SAR_Test_Report_Part2

FCC ID: 2AFZZC3JH

RF Exposure Info

Download: PDF
FCCID_4403713

® In Collsborationwith -iTTL a e a LABORATORY Add: No.5 1 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +8 6. 10—6230463 3—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http//www.chinatt.en Measurement Condit ions Dasy System configuration, as far as not given on page 1. DASY Version DasY52 52.10.0.1446 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom 5.1C Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz = 5 mm Frequency 1900 MHz & 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 40.0 1.40 mho/m Measured Head TSL parameters (22.0 £0.2) °C 39.9 £ 6 % 141 mho/m £ 6 % Head TSL temperature change during test <1.0 °C — — SAR result with Head TSL SAR averaged over 1_Cm2°_(1 g) of Head TSL Condition SAR measured 250 mW input power 10.1 mW/g SAR for nominal Head TSL parameters normalized to 1W 40,1 mW /g £ 18.8 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL Condition SAR measured 250 mW input power 5.19 mW /g SAR for nominal Head TSL parameters normalized to 1W 20.7 mW Ig £ 18.7 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 53.3 1.52 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 53.6 46 % 1.53 mho/m + 6 % Body TSL temperature change during test <1.0 °C —— — SAR result with Body TSL SAR averaged over 1 cm* _(1 g) of Body TSL Condition SAR measured 250 mW input power 9.90 mW /g SAR for nominal Body TSL parameters normalized to 1W 39.5 mW /g + 18.8 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL Condition SAR measured 250 mW input power 5.21 mw/g SAR for nominal Body TSL parameters normalized to 1W 20.8 mW 1g £ 18.7 % (k=2) Certificate No: Z17—97115 Page 3 of 8

® in Collaborationwith TTL a CALIERATION LABORATORY Add: Iy Xueyuan Road, Haidian Tek +3g]s|; District, Beijing, 100191, China Bomghq §2304633—2079 Pug:+86—10—02308633—2504 all: ettl@chinattl.com hitps//wwawchinatten Appendix (Additional assessments outside the scope of CNAS L0570) Antenna Parameters with Head TSL Impadance, transformed to feed point 52.00+ 6.5910 Return Loss —23.408 Antenna Parameters with Body TSL Impedance, transformed to feed point §52.70+ 8.3510 Return Loss —21.408 General Antenna Parameters and Design Elactrical Delay (one direction) J 1.302 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antennais therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in orderto improve matching when loaded according to the position as explained in the "Measurement Conditions® paragraph. The SAR data are not affected by this change. The overall dipole lengthis still according to the Standard No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z17—97115 Page 4 of 8

b’ in Collaboration with ©77TJI a 1\-/ causranon tasor, Add: No.51 Xueyuan Road . Haidian District, Beijing. Eel: f!{s- mfz:_om:. 100191, China mw Fax: +86—10—62304633—2504 »mail: ¢H @chinaitl.com bups//wwchinanl.en DASY5 Validation Report for Head TSL Test Laboratory: CTTL, Beijing, China Bate: 08.26.2017 UT: Dipole 1900 MHz; Typ e: D1900V2; Serial: D1900V 2 — SN: 54060 Communication System: UID 0, CW; Fre quency: 190 0 MHz: Duty Cycle: 1:1 Medium parameters used: f= 190 0 MHz; 0 = 1.413.8/m; er=39.85; Phantom section: Left Section p= 1000 kg/m3 Mcasurement Standard: DASYS (IEE EIEC/ANSI ©63.19—2007) DASY3 Configuration: »— Probe: EX3DV4— SN3617; ConvF(8.26, 8.26, 8.26); Calibrated: 1/23/2017; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn1331; Calibrated: 1/19/2 017 * Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 + Measurement SW: DASY52, Version 52.10 (0); SEMCA D X Version 14.6.10 (7417) System Performance Check/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measure ment grid: dx=5mm, dy=Smm, dz=Smm Reference Value =94.94 V/m; Power Drift=0.01 dB Peak SAR (extrapolated)=19.5 W/kg SAR(I g) =10.1 W/kg; SAR(10 g)=5.19 W/kg Maximum value of SAR (measured)= 15.9 W/kg ~3.64 ~1.28 10.93 14.57 18.21 _ 0 dB =15.9 W/kg=12.01 dBW/kg Certificate No: Z17—97115 Page 5 of 8

#dd: No.51 Xueyuan Road, Haidis T: 86—10—62304633—2079 ian District, Befjing, 100191, China E—mail: cri@chinattl.com ray, +ss-|o-5536'3533-2504 hitp/fwww.chinatten Impedance Measurement Plot for Head TSL Tri si1 Log Hag 10.00087 nef 0.000d0 [F2] 50. * i—asvtor en crranr as «0. 00 —— > 30.00 _ _1 20.00 _ —_. 20,00 — I — & + — 0. 0000 — > : + abe.__1 — (f —20.00 ‘ ~20.00 ~30.00 ~40.00 ~50.00 IMIBRM s11 snith (a+p) scale 1,0000 [FL oe1] »2. 2,9000000 ahz 31.991 0 6.5866 o. 551.7, Certificate No: 217—97115 Page 6 of 8

Add:y No.51 Xueyyuan Roud, idion n Distric Di t, Beljing i , 100191, China j TEI» *_85-I0-623I]4633-2fl79 Haidia i Fax: +86—10—62304633—2504 —mall: ctll@chinattl.com hipolinwwchinattl.en DASYS Validation Report for Body TSL Date: 08.26.20 17 Test Laboratory: CTTL, Beijing, China DUT: Dipole 1900 MHz; Type: D1900V2; Serial; D1900V2 — SN: 50060 Communication System: UID 0. CW; Frequency: 1900 MHz; Duty Cycle: 1:1 Medium parameters used: = 1900 MHz; a= 1.528 S/im; ; = 53.55; p=1000 kg/m! Phantom section: Center Section Measurement Standard: DASY5 (IEEEIEC/ANSI C63.19—2007) DASYS5 Configuration: * Probe: EX3DV4 — SN3617; ConvF(7.95, 7.95, 7.95); Calibrated: 1/23/2017; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn1331; Calibrated: 1/19/2017 + Phantom: Triple Plat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 + Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) System Performance Check/Zoom Scan (7x787) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=Smm, dz=5mm Reference Value =91.19 V/m; Power Drif=0.01 dB Peak SAR (extrapolated)= 18.1 W/kg SAR(I g) = 9.9 W/kg; SAR(LO g)=5.21 Wikg Maximum value of SAR (measured) =15.3 W/kg 0 dB=15.3 W/kg = 11.85 dBW/kg Certificate No: Z17—97115 Page 7 of 8

C !-\- in Collaboration with 2 7TI a ‘, CAUB RANON LABOR ATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China 1:: : +86—1 fl~623_0463 3<1079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hups//wwachinaltlen Impedance Measurement Plot for Bod y TSL Tri SX Log nag 15. 09087 nar 0.00008 iT 50.0 * pr— romumrec—amore 40.00 ——— 30.00 ———— 20.00 10.00 % F 0.000p] +4 f 1 ~20.00 —f ~20.00 ~30.00 ~40.00 c m sia smith (raefx) seate 1.0000 [ri oel] s1 2.9000000 GHz $2.660 0. s.3483 0 699. 39. om Certificate No: 217—97115 Pagesofs

TL sop—0—a_o _ *\ tikky ® in Collaboration with C uy Add: N n epuennion taqnstont l‘CNASMWN oad, Haidian District, Beijing, 100191, Chis ‘f, f Tel +85.ié.’éz;oy:;l;zr% Tec "B6.To—2304633 2s _ *4 "h, * CNAS LO570 E—mail: cttl@chinattl.com hitp://wwwchinattl.en ~diachas 7 s zen S Client [TA(Shanghai) _____ | [Gertificate No:\ 217—97116 Object (b2asova®su~7a§ es ul 4P l Calibration Procedure(s) ee m mm | Calibration Procedures for dipole validation kits_ Calibration date: (August 29,2017 _ This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility; environment temperature(2223)c and humidity<70%. Callbration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRVD 102083 22—Sep—16 (CTTL, No.J16X06309) Sep—17 Power sensor NRV—Z5 100595 22—Sep—16 (CTTL, No.J16X06809) Sep—17 Reference Probe EX3DV4 SN 3617 23—Jan—17(SPEAG,No.EX3—3617_Jan17) Jan—18 DAE4 SN 1331 18—Jan—17(CTTL—SPEAG,No.217—97015) Jan—18 Secondary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Signal Generator E4438C MY49071430 13—Jan—17 (CTTL, No.J17X00286) Jan—18 Network Analyzer E5071C MY46110673 13—Jan—17 (CTTL, No.J17X00285) Jan—18 N_amg _ Functlon — es — Signature Calibrated by: |Zhao Jing SAR Test Engineer Reviewed by: | Lin Hao SAR TestEnémeér Approved by: {Q[Dianyuan SAR Project Leader Issued: September 1, 2017 This calibration certificate shall not be reproduced except in full without written approvalof the laboratory. Certificate No: Z17—97116 Page 1 of 8

!\' in Collaboration with %TTL a Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http://wwwchinattl.en Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORMx,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for assessment of specific absorption rate of human exposure to radio frequency fields from hand—held and body—mounted wireless communication devices— Part 1: Device used next to the ear (Frequency range of 300MHz to 6GHz)", July 2016 c) IEC 62209—2, "Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices used in close proximity to the human body (frequency range of 30MHz to 6GHz)", March 2010 d) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. & Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. * SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. Certificate No: Z17—97116 Page 2 of 8

top—.> * in Collaboration with TTL a CALIBRATION LABORArory Add: No.S1 Xucyuan Road, Haidian District, Neljing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ctt!@chinattl.com hitps//www.chinattl.en Measurement Conditions DASY system configuration, as far as not given on page 1 DASY Version DASY52 52.10.0.1446 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom 5.1C Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2450 MHz £ 1 MHz Head TSL parameters The followingparameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0°C 39.2 1.80 mho/m Measured Head TSL paramaters (22.0 £0.2) °C 39.7 26 % 1,82 mho/m £ 6 % Head TSL temperature change during test <1.0 °C — hane SAR result with Head TSL SAR averaged over 1_Cm"_(1g) of Head TSL Condition SAR measured 250 mW input power 13.2 mW/g SAR for nominal Head TSL parameters normalized to 1W 52.6 mW ig 4 18.8 % (k=2) SAR averaged over 10 cm° (10 g) of Head TSL Condition SAR measured 250 mW input power 6.16 mW /g SAR for nominal Head TSL parameters normalized to 1W 24.6 mW ig £ 18.7 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permitivity Conductivity Nominal Body TSL parameters 22.0 °C §2.7 1.95 mho/m Measured Body TSL parameters (22.0 £0.2) °C 525146 % 1.94 mho/m £ 6 % Body TSL temperature change during test <1.0°C us se SAR result with Body TSL SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 250 mW input power 12.7 mW /g SAR for nominal Body TSL parameters normalized to 1W 50.8 mW Ig + 18.8 % (k=2) SAR averaged over 10 _cm> _(10 g) of Body TSL Condition SAR measured 250 mW input power 587 mW 1g SAR for nominal Body TSL parameters normalized to 1W 23.5 mW 1g 2 18.7 % (k=2) Certificate No: Z17—97116 Page 3 of 8 vems eopores ornan e we we roprenracen cnnupe mm gony c

’ in Collaboration with g L __MLL_ Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com http:/www.chinattl.en Appendix (Additional assessments outside the scope of CNAS LO570) Antenna Parameters with Head TSL Impedance, transformed to feed point 53.40+ 4.29)0 Returm Loss —25.50B Antenna Parameters with Body TSL Impedance, transformed to feed point 51.00+ 6.6110 Return Loss —23.6dB General Antenna Parameters and Design Electrical Delay (one direction) 1,265 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductorof the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in orderto improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data [ Manufactured by SPEAG ] Certificate No: Z17—97116 Page 4 of 8

Caueranon Lagorarory Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ctt!@chinattl.com http/frww.chinatth.en DASYS Validation Report for Head TSL Date: 08.29.2017 Test Laboratory: CTTL, Beijing, China DUT: Dipole 2450 MHz; Type: D2450V2; Serial; D2450V2 — SN: 786 Communication System: UID 0, CW; Frequency: 2450 MHz; Duty Cycle: 1:1 Medium parameters used: £= 2450 MHz; 0 = 1.822 S/m; er = 39.65; p = 1000 kg/m3 Phantom section; Left Section Measurement Standard: DASYS (IEEE/AIEC/ANSI €63.19—2007) DASYS Configuration: + Probe: EX3DV4 — SN3617; ConvF(7.74, 7.74, 7.74); Calibrated: 1/23/2017; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) + Electronics: DAE4 Sn1331; Calibrated: 1/19/2017 + Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 * Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurementgrid: dx=5mm, dy=5mm, dz=5mm Reference Value=105.1 V/m; Power Drift= —0.03 dB Peak SAR (extrapolated)=27.5 W/kg SAR(I g)=13.2 W/kg; SAR(10 g)=6.16 W/kg Maximum value of SAR (measured) =22.2 W/kg dB 0 ~4.33 —8.66 12.98 "17.31 C —21.64 0 dB =22.2 W/kg=13.46 dBW/kg Certificate No: Z17—97116 Page 5 of8

t in Collaboration with CALIBRATION LABORKTORy Add: No.51 Xueyuan Road, Haidian District, Beljing, 100191, China Tel: +86—10—62304633—2079 Fax: +6—1 M?)fl‘fl]—lim E—mail: e@chinatt.com hitp/wwwchinatilen Impedance Measurement Plot for Head TSL Tri iX Log mag 10.00007 wer 5. 00008 [FI] 00(51 2322300000 one —33.30. ds 40.00 30.c0 20.00 10.60 0. 000 B 4 —10.00 —20.00 —30.00 ~40.c0 —50.c0 NIRBJ 511 seith (ReJX) Scale 1.000U [¢1 bel] »2. 2.4500000 cz 83.436 0. 4.2806 0. 278.3 Certificate No: 217—97116 Page 6 ofs

@TTL s‘p.e—a Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel:+86—10—62304833—2079 Fax: +86—10—62304633—2504 E—mail: ctti@chinattl.com hitps/wwchinattl.en DASY5 Validation Report for Body TSL Date: 08.29.2017 Test Laboratory: CTTL, Beijing, China DUT: Dipole 2450 MHz; Type: D2450V2; Serial; D2450V2 — SN: 786 Communication System: UID 0, CW; Frequency: 2450 MHz; Duty Cycle: 1:1 Medium parameters used: {=2450 MHz; 0= 1.943 S/m; &,= 52.45; p= 1000 kg/m* Phantom section: Right Section Measurement Standard: DASYS (IEEE/IEC/ANSI €63.19—2007) DASY5 Configuration: + Probe: EX3DV4 — SN3617; ConvF(7.8, 7.8, 7.8); Calibrated: 1/23/2017; + Sensor—Surface: 1Amm (Mechanical Surface Detection) * Electronics: DAE4 Sn1331; Calibrated: 1/19/2017 * Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 * Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=Smm, dy=5mm, dz=5mm Reference Value =92.28 V/m; Power Drift =—0.01 dB Peak SAR (extrapolated) = 27.0 W/kg SAR(L g)= 12.7 W/kg; SAR(1O g)= 5.87 W/kg Maximum value of SAR (measured) = 21.5 W/kg dB 0 ~4.38 —8.75 13.13 —17.50 L —21.80 0 dB =21.5 W/kg =13.32 dBW/kg Certificate No: Z17—97116 Page 7 of 8

TL : p -ema q CALIBRATION LABORArory Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitps//wwwchinatten Impedance Measurement Plot for Body TSL Tri siL Log nay 10.00087 ner 0,000d8 [F1] s0.00 31 —7.2500005 onz —23, 801. de 40.00 T 30. 06 20. 00 20. 00 ; ~40. oo ~50. 00 M si1 snith (RJ>) scale 1.000u [ea oel] »1 2.4500000 anz S1.046 0 6.6076 0. 420.2 Certificate No: 217—97116 Page 8 of 8

es as"wil a «l7 M PRWH TTL s a j\\—_,/;’?CNASggfl Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, Chinn S v CALIBRATION Tel: +86—10—62304033—2079 Fux: +86—10—62304637—2504 "m“ CNAS LO570 E—mail ettl@chinatiLoom hitpetfwenwchinattlen TA(Shanghal) Certificate No: 218—60094 en‘ '“;‘F > =———l TJON CERTIFICATE______ e e Object D2600V2 — SN 1025 Calibration Procedure(s) FP211—003—01 Calibration Procedures for dipole validation kits Calibration date: May 2, 2018 This calibration Cerfificate documents the traceability to national standards, which realize the physical units of measurements(S)), The messurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(2223)C and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRVD 102083 O1—Nov—17 (CTTL, No.J17X08756) Oct—18 Power sensor NRV—Z5 100542 01—Nov—17 (CTTL, No.J17X08766) Oct—18 Reference Probe EX3DV4 SN 7464 12—Sep—17(SPEAG No.EX3—7464_Sep17) Sep—18 DaE4 sN1525 02—0ct—17(SPEAG No,DAE4—1525_Oct17) Oct—18 Secondary Standards 1D # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Signal Generator E4438C MY49071430 23—Jan—18 (CTTL, No.J18X00560) Jan—19 Network Analyzer E5071C MY46110673. 24—Jan—18 (CTTL, No.J18X00561) Jan—19 Name Function Sigqature Calibrated by: ‘Zhao Jing SAR Test Engineer q&@f4%. ¢ Reviewed by:e Lin Hao 1 / ~ubo SAR Test Engineer Lfi‘fi%} {\:'l \ 7 1'5‘:‘ Appraved by: Ql Dianyuan SAR Project Leader ; ,"."e/ % /;/,'--; , lssued: May 5, 20418 *6 This calibration certificate shall not be reproduced except in full without written approvalof the laboratory, Certificate No: Z18—60094 Page 1 of 8

C !TTL ;_Leiar_s._ CALIRZATION LABORATORY Add: No,51 Xuey uan Road, Haldian District, Heijing, 100191, China Tet +86—10—62304633—2070 Fux: +8be10—62304633—2504 Exmail: ettl@chinatt.com httpeiriwceliintther Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORMx.y.a NA not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, *IEEE Recommended Practice for Determining the Peak Spatia—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices; Measurement Techniques®, June 2013 b) IEC 62209—1, "Measurement procedure for assessment of specific absorption rate of human exposure to radio frequency fields from hand—held and body—mounted wireless communication devices— Part 1: Device used nextto the ear (Frequency range of 300MHz to 6GHz)", July 2016 c) IEC 62209—2, *Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices used in close proximity to the human body (frequency range of 30MHz to 6GH2z)", March 2010 d) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: «_ Measurement Conditions: Further details are available from the Validation Report at the end ofthe certificate. All figures stated in the certificate are valid at the freq uency indicated. a Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the fiat phantom section, with the arms oriented parallel to the body axis. «_ Feed Point Impedance and Retum Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. «_ Electical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required.. «_ SAR measured: SAR measured at the stated antenna input power. «_ SAR normalized: SAR as measured, normalized to an input powerof 1 W at the antenna connector. «_ SAR fornominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR res ult. The reporied uncertainty of measurement is stated as the standard uncertainty of Measurement multipied by the coverage factor k=2, which for a normal distribution Corrasponds to a coverage probability of approximately 95%. Certificate No: Z18—60094 Page 2 of 8

« TTL ;_um_a.s_ CALIERATION LABORATORY Add: No,$1 Xuey an Road, Haklian District, Beljing. 10019 China Tel:+86—10—62304632—2079 Faxt +86—10—62304633—2504 E—muil ctt}zchinattl.com hitpsthnin;chinstthen Measurement Conditions DASYsystem configuration, as far as not gven on page 1. DASY Vorsion DASY52 $2,10.0.1446 Extrapolation Advanced Extrapotation Phantom Triple Flat Phantom 5.1C Distance Dipole Center —TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, ce = 5 mm Frequancy 2600 MHz + 1 MHz Head TSL paramaters The following parameters and calculations were applied. Temporature Parmittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.0 1.98 mhaim Measured Hoad TSL para meters (22.0 £0.2) °C 40.1 £6% 2.01 mho‘m # 6 % Head TSL tomperature change during test <1.0 °C — a SAR result with Head TSL SAR averagedover 1_cnt"_(1 g) of Head TSL Condition SAR measured 250 mW input power 136 mW/g SAR for nominal Head TSL parameters normallzed to 1W 54.1 mW (g # 18.8 % (k=2) SAR avoraged over 10 cm? (10 g) of Head TSL Condition SAR measured 250 mW input power 6.03 mW /g SAR for nominal Head TSL parameters normalized to 1W 24,1 mW /g 4 18.7 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Pormittivity Conductivity Nomiral Body TSL paramoters 22.0°C §2.6 2.16 mhaim Measurad Body TSL parameters (22.020.2) °C §2116% 2.15 mhoim + 6.% Lawd-y TSL temperature change during test <1.0°C — n SAR result with Body TSL SAR avoraged over 1 cm> (1 g) of Body TSL Condition SAR measured 250 mW input power 13.6 mW/g SAR for nominal Body TSL parameters normalized to 1W 54.5 mW /g +#18.8 % (k=2) SAR averaged over 10. Cm* {10 g) of Body TSL Condition SAR measured 250 rrW input power 6.05 mW /g SAR for nominal Body TSL parameters normalized to 1W 24.3 mW Ig & 18.7 % (ke2) Certificate No: Z18—60094 Page 3 of #

é_TTL ;—E_?:l_fl_—- CALIBRATION LABORATORY Add: No.S1 Xury uan Road, Haiian District, Beljing, 100 191, Chine Tel: +86—10—62304633—2079 Fiee: +86—10—62304633—2504 E—mail: atk@chinattLcom hitphwwchinattLen Appendix(Additional assessments outside the scope of CNAS LO570) Antenna Parameters with Head TSL Impadance, transformed to feed point 48.10—7.55]0 Retum Loss —22.008 Antenna Parameters with Body TSL impadance, transformed to feed point 46.60—7.0510 Retum Loss —21.908 General Antenna Parameters and Design Electrical Delay (one direction) 1,014 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured, The dipole is made ofstandard semingid coaxial cable. The center conductor of the feeding line is direcily connected to the second arm ofthe dipole. The antenina is therefore short—cirouited for DC—signals, On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend orthe soldered connections nearthe feedpoint may be damaged, Additional EUT Data Manufactured by | sFreac _ Certificate No: Z18—60094 Page 4 of n

C BP3 inColsborsionwith 7T‘J, <, s a e a Add: No.$1 Xueyuan Road, Haidian District, Beijing, 100191, China Tek +86—10—62304633—2079 Fax: +86—10—02304633—2504 E—mail: ctt¥@ichinattl.coms hitp oAwww chinattl en DASYS Validation Report for Head TSL Date: 05.02.2018 Test Laboratory: CTTL, Beijing, China DUT: Dipole 2600 MHz; Type: D2600V2; Serial: D2600V2 — SN; 1025 Communication System: UID 0, CW; Frequency: 2600 MHz; Duty Cyele: 1 :1 Medium parameters used: £= 2600 MHz; 0 = 2.014 S/m; er = 40.09; p = 1000 kg/m3 Phantom section: F it Section Measurement Standard: DAS Y5 (IEEE/IEC/ANSI C63.19—2007) DASY5 Configuration: + Probe: EX3DV4 — SN7464; ConvF(7.76, 7.76, 7.76); Calibrated: 9/12/2017; * Sensor—Surface: 1 4mm (Mechanical Surface Detection) * Electronies: DAE4 Sn1525; Calibrated: 10/2/2017 * Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 * Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0; Measurement grid: dx=3 mm, dy=Smm, dz=5mm Reference Value = 98.50 V/m; Power Drift= 0.00 dB Peak SAR (extrapolated) = 29.6 W/kg SAR(I g)=13.6 Wikg; SAR(10 g)=6.03 W/kg Maximum value of SAR (measured)= 23.5 W/kg ~4.80 —1.59 ~14.39 ~19.18 ~23.98 L. 0 dB =23.5 Wikg =13.71 dBWkg Certificate No: Z18—60094 Page 5 of &

In Collaberation with TTL a CAUIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191,China Tel: +86—10—62304633—2079 Fix: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitprtivinchinatLen Impedance Measurement Plot for Head TSL Tri siT Log nag 10.00d87 ref 0.00000 [F] $0.00 H 2w ene <22.00 0s 10.60 30.00 20.00 10.00 a.coo y —10. 00 i ~20. 00 ~30. 00 40. 00 ~40.c0 e sin satch (rofx) scale 1.0000 [52 oel] s1 2.6000000 onz 48.007 o —7.8%0r 8. .1 Certificate No: Z18—60094 Page 6 of 8

C !\ In Collaboration with @7"7"J, un sa Add: No.51 Xuey uan Road, Haidian District, Beljing. 100191, China Tel +86—10—62304633—2070 Fax: +86—10—62304633—2504 E—mail: cttl@chinatiL.com bitpriwwwchinatthen DASYS Validation Report for Body TSL Date: 05.02.2018 Test Laboratory: CTTL, Beijing. China DUT: Dipole 2600 MHz; Type: D2600V2; Serial: D2600 V2 — SN: 1025 Communication System: UID 0, CW; Frequency: 2600 MHz; Duty Cycle: 1 :1 Medium parameters used: {= 2600 MHz; 0 = 2.146 S/m; & = 52.09; p = 1000 kg/m* Phantom section: Right Section Mcasurement Standard: DASY3 (IEEE/IEC/ANSI €63.19—2007) DASYS Configuration: «_ Probe: EX3DV4 — SN7464; ConvF(7.$4, 7.84,7.84); Calibrated : 9/12/2017; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 $n1525; Calibrated: 10/2/2017 * Phantom: Tripk Flat Phantom 5.1C; Type: QD 000 PS1 CA; Serial: 1161/1 * Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7 )Cube 0: Measurement grid : dx=5 mm, dy=5mm, dz=5mm Reference Value = 83.79 V/im; Power Drift= 0.02 dB Peak SAR (exirapolated)=29.7 W/kg SAR(L g)= 13.6 Wikg; SAR(IO g)=6.06 W/kg Maximum value of SAR (measured)= 23.6 W/kg dB o ~4.69 —9.38 14.07 18.76 . —23.45 0 dB =23.6 Wikg =13.73 dB Wikg Certificate No: £18—60094 Page 7 of 8

TTi, ;_e_éi_.q_ Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattLcom hitpoiwww.chinattLen Impedance Measurement Plot for Body TSL Tek si% Lo nay 10.00007 nef 0.90000 [Fi] **+ 09. 223000000 5t ne —#1. ad £0.00 30.c0 20.c0 10.c0 o.oco9) i —10.00 —20.00 ~s0.00 ~s0.00 ~$0,00 a IMIRM 511 smith (iefx) Scale 1.000u {e1 bel) 3%. 2,6000000 ohz d6.642 6 —7.056% n 8.67 Certificate No: Z18—60094 Page 8 of 8

EE‘A zs CALIBRATION LABoRArory Mfi CNA ‘ & Rag Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China ’4,,/—\\\\‘ v CALIBRATION Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 /,,m\.\\ CNAS LO570 E—mail: cttl@chinattl.com http://www.chinattl.en Client TA(Shangha|) Certificate No: 217—97001 Object DSGHzV2 — SN: 1151 Calibration Procedure(s) FD—Z11—003—01 Calibration Procedures for dipole validation kits Calibration date: January 5, 2017 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(22+3)‘C and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRP2 101919 27—Jun—16 (CTTL, No.J16X04777) Jun=17 Power sensor NRP—Z291 101547 27—Jun—16 (CTTL, No.J16X04777) Jun—17 ReferenceProbe EX3DV4 SN 7433 26—Sep—16(SPEAG,No.EX3—7433_Sep16) Sep—17 DAE4 SN 771 02—Feb—16(CTTL—SPEAG,N0.Z16—97011) Feb—17 Secondary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Signal Generator E4438C MY49071430 01—Feb—16 (CTTL, No.J16X00893) Jan—17 NetworkAnalyzer E5071C MY46110673 26—Jan—16 (CTTL, No.J16X00894) Jan—17 Name Function Signature Calibrated by: Zhao Jing SAR Test Engineer Reviewed by: Qi Dianyuan SAR Project Leader Approved by: Lu Bingsong Deputy Director of the laboratory 1 Issued: January 7{42017 This calibration certificate shall not be reproduced exceptin full without written approval of the laboratory. Certificate No: Z17—97001 Page 1 of 14

*® In Collaboration with m_‘7/"]"J, -““/ a CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitp://www.chinattl.en Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORMx,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) For hand—held devices used in close proximity to the ear (frequency range of 300MHz to 3GHz)", February 2005 c) IEC 62209—2, "Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices used in close proximity to the human body (frequency range of 30MHz to 6GHz)", March 2010 d) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: «_ Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. * SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. Certificate No: Z17—97001 Page 2 of 14


Document Created: 2019-08-16 16:51:09
Document Modified: 2019-08-16 16:51:09
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC