SAR_Test_Report_ANNEX E1

FCC ID: 2AFZZC3IG

RF Exposure Info

Download: PDF
FCCID_4440697

l7/7 tEANT 1 @x‘7"/"J , a s P In Collaboration with ‘ in 8 A AkraiA S wWmaaeese>" CALIBRATION LABORATORY kCNA Toaneg S#: »llfl\‘\ v CALIBRATION Add: No.51 Xucyuan Road, Haidian District, Beijing, 100191, China Mlll CNAS L0570 Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com Hitp://www.chinattl.on Certificate No: 219—60101 CALIBRATION CERTIFICATE Object ES3DV3 — SN:3090 Calibration Procedure(s) FF—211—004—01 Calibration Procedures for Dosimetric E—field Probes Calibration date: April 12, 2019 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(@2243)°c and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRP2 101919 20—Jun—18 (CTTL, No.J18X05032) Jun—19 Power sensor NRP—Z91 101547 20—Jun—18 (CTTL, No.J18X05032) Jun—19 Power sensor NRP—Z91 101548 20—Jun—18 (CTTL, No.J18X05032) Jun—19 Reference10dBAttenuator 18N50OW—10dB 09—Feb—18(CTTL, No.J18X01133) Feb—20 Reference20dBAttenuator 18N5OW—20dB 09—Feb—18(CTTL, No.J18X01132) Feb—20 Reference Probe EX3DV4 SN 7514 27—Aug—18(SPEAG,No.EX3—7514_Aug18/2) Aug—19 DAE4 SN 1555 20—Aug—18(SPEAG, No.DAE4—1555_Aug18) Aug —19 Secondary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration SignalGeneratorMG3700A 6201052605 21—Jun—18 (CTTL, No.J18X05033) Jun—19 Network Analyzer E5071C MY46110673 24—Jan—19 (CTTL, No.J19X00547) Jan —20_ Name Function Signature Calibrated by: Yu Zongying SAR Test Engineer Reviewed by: Lin Hao SAR Test Engineer T{M Approved by: Qi Dianyuan SAR Project Leader Seys \_." Issued: April 14, 2019 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: Z19—60101 Page 1 of 11

A‘ In Collaboration with @‘7/"/‘]/, sa p e _ Wiaaayy>>" CALIBRATION LABORATORY Add: No.51 Xucyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com Hittp://www.chinattl.cn Glossary: TSL tissue simulating liquid NORMx,y,z2 sensitivity in free space ConvF sensitivity in TSL / NORMx,y,z DCP diode compression point CF crest factor (1/duty_cycle) of the RF signal A,B,C,D modulation dependent linearization parameters Polarization ® 4 rotation around probe axis Polarization 0 0 rotation around an axis that is in the plane normal to probe axis (at measurement center), i O0=0 is normal to probe axis Connector Angle information used in DASY system to align probe sensor X to the robot coordinate system Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Methods Applied and Interpretation of Parameters: e NORMx,y,z: Assessed for E—field polarization 0=0 (fs900MHz in TEM—cell; f>1800MHz: waveguide). NORMx,y,z are only intermediate values, i.e., the uncertainties of NORMx,y,z does not effect the E" field uncertainty inside TSL (see below ConvF). e NORM(Px,y,z2 = NORMx,y,z* frequency_response (see Frequency Response Chart). This linearization is implemented in DASY4 software versions later than 4.2. The uncertainty of the frequency response is included in the stated uncertainty of ConvF. e DCPx,y,z; DCP are numerical linearization parameters assessed based on the data of power sweep (no uncertainty required). DCP does not depend on frequency nor media. e PAR: PAR is the Peak to Average Ratio that is not calibrated but determined based on the signal characteristics. e Axyz Bx,y,z; Cx,y,z;VRx,y,z:A,B,C are numerical linearization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltage across the diode. e ConvF and Boundary Effect Parameters: Assessed in flat phantom using E—field (or Temperature Transfer Standard for fs800MHz) and inside waveguide using analytical field distributions based on power measurements for f >800MHz. The same setups are used for assessment of the parameters applied for boundary compensation (alpha, depth) of which typical uncertainty valued are given. These parameters are used in DASY4 software to improve probe accuracy close to the boundary. The sensitivity in TSL corresponds to NORMx,y,z* ConvF whereby the uncertainty corresponds to that given for ConvF. A frequency dependent ConvF is used in DASY version 4.4 and higher which allows extending the validity from:+50MHz to+100MHz. e Spherical isotropy (3D deviation from isotropy): in a field of low gradients realized using a flat phantom exposed by a patch antenna. e Sensor Offset: The sensor offset corresponds to the offset of virtual measurement center from the probe tip (on probe axis). No tolerance required. e Connector Angle: The angle is assessed using the information gained by determining the NORMx (no uncertainty required). Certificate No: Z19—60101 Page 2 of 11

mm© in collsboration with =‘/"/‘/, s p e a q Wmm CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail; cttl@chinattl.com Hittp://www.chinattl.en Probe ES3DV3 SN: 3090 Calibrated: April 12, 2019 Calibrated for DASY/EASY Systems (Note: non—compatible with DASY2 system!) Certificate No: Z19—60101 Page 3 of 11

48 in Collsboration with a=‘/"/‘]/, a Wiaages>"" CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Hitp://www.chinattl.en DASY/EASY — Parameters of Probe: ES3DV3 — SN: 3090 Basic Calibration Parameters Sensor X Sensor Y Sensor Z Unc (k=2) Norm(uV/(V/im))A 1.22 1.38 1.33 £10.0% DCP(mV)® 104.2 104.9 104.1 Modulation Calibration Parameters UID Communication A B C D VR Unc System Name dB dByuV dB mV (k=2) 0 Cw X 0.0 0.0 1.0 0.00 260.9 +2.8% Y 0.0 0.0 1.0 280.0 Z 0.0 0.0 1.0 276.1 The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. A The uncertainties of Norm X, Y, Z do not affect the E*—field uncertainty inside TSL (see Page 5 and Page 6). 8 Numerical linearization parameter: uncertainty not required. & Uncertainly is determined using the max. deviation from linear response applying rectangular distribution and is expressed for the square of the field value. Certificate No: Z19—60101 Page 4 of 11

;7'"“]'_’2 In Collaboration with 31 s_ p _e a _0 s CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: ctti@chinattl.com Hitp://www.chinattl.on DASY/EASY — Parameters of Probe: ES3DV3 — SN: 3090 Calibration Parameter Determined in Head Tissue Simulating Media . . ; f[MHz]® P::]'i:i"‘:;w c°"°:;7r:‘)":y ConvF X ConvF Y GConvF Z Alpha® D(:’:) :’k:;t) 750 a1.9 0.89 622 622 622 040 145 +£121% 835 41.5 0.90 6iz 612 612 045 145 +121% 1750 40.1 1.37 536 536 536 065 125 121% 1900 40.0 1.40 506 506 506 ofi 120 +121% 2300 39.5 1.67 4.81 4.81 asi 0.90 1.08 £121% 2450 39.2 1.80 as? 457 457 090 1.08 £121% 2600 39.0 1.96 aas 448 448 090 107 £121% © Frequency validity above 300 MHz of +100MHz only applies for DASY v4.4 and higher (Page 2), else it is restricted to *50MHz. The uncertainty is the RSS of ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validity below 300 MHz is * 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Above 5 GHz frequency validity can be extended to + 110 MHz. F At frequency below 3 GHz, the validity of tissue parameters (¢ and 0) can be relaxed to +10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (e and 0) is restricted to £5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters. © Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for the frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: Z19—60101 Page 5 of 11

=A® In Collaboration with ‘/"/‘/, s p e a g V CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Hitp://www.chinattl.on DASY/!EASY — Parameters of Probe: ES3DV3 — SN: 3090 Calibration Parameter Determined in Body Tissue Simulating Media n x a f [MHz]® Pe?r:Iie:iI:/’::y ¢ Cond(;;:::\)n:y ConvF X ConvF Y ConvF Z Alpha® D(:):) ::::;t) 750 §65.6 0.96 6.40 6.40 6.40 0.40 1.30 |#121% 835 55.2 0.97 6.18 6.18 6.18 0.48 146 +12.1% 1750 53.4 1.49 4.95 4.95 4.95 0.64 1.30 £12.1% 1900 63.3 1.52 4.19 4.19 4.19 0.65 1,29 £12.1% 2300 52.9 1.81 4.54 4.54 4.54 0.70 1.32 £12.1% 2450 §2.7 1.95 4.A7 4.A7 4.A7 0.75 1.30 £12.1% 2600 52.5 2.16 4.24 4.24 4.24 0.80 1.22 £12.1% © Frequency validity above 300 MHz of +100MHz only applies for DASY v4.4 and higher (Page 2), else it is restricted to *50MHz. The uncertainty is the RSS of ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validity below 300 MHz is + 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Above 5 GHz frequency validity can be extended to * 110 MHz. " At frequency below 3 GHz, the validity of tissue parameters (s and 0) can be relaxed to £10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (€ and 0) is restricted to £5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue parameters. © Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for the frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: Z19—60101 Page 6 of 11

mWz© in Collaboration with a=‘/"[‘[, a m CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Hitp://www.chinattl.en Frequency Response of E—Field (TEM—Cell: ifi110 EXX, Waveguide: R22) Frequency response {normalized) T T I T T T 0 500 1000 1500 2000 2500 3000 [—=—] f [MHz] =o— TEM R22 Uncertainty of Frequency Response of E—field: £7.4% (k=2) Certificate No: Z19—60101 Page 7 of 11

4&C in collsboration with =®‘/"/‘]/, s p e a q uy CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Hitp://www.chinattl.on Receiving Pattern (®), 0=0° f=600 MHz, TEM f=1800 MHz, R22 Error[dB] + f i ~150 ~100 —50 0 — 50 — 1(I)0 l 150 Rollfe] [—*~100MHz __—+—600MHz —+— 1800MHz___—+— 2500MHz] Uncertainty of Axial Isotropy Assessment: £1.2% (k=2) Certificate No: Z19—60101 Page 8 of 11

In Collaboration with a=‘/"/‘/, a Wiapaaee>>" CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com Http://www.chinattl.on Dynamic Range f(SARnead) (TEM cell, f = 900 MHz) Input Signal[u¥] 10° 3 SAR[mW/cm] [—M—)not compensated —@— compensated Error{dB] i44 i—i———4 : 10° 10° 4 SAR[mW/cm [___ —®—|not compensated —e— compensated _] Uncertainty of Linearity Assessment: £0.9% (k=2) Certificate No: Z19—60101 Page 9 of 11

bfi In Collaboration with ‘/"/‘/, s p e a q y CALIBRATION LABORATORY Add: No.51 Xucyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Hittp://www.chinattl.en Conversion Factor Assessment f=835 MHz, WGLS R9(H_convF) {=1900 MHz, WGLS R22(H_convF) 4.00 30.00 3.50 \ n mjm \ 8 8 orn S sARWAgW SAR[WAgV L* s m a S & \ 10.00 : 1.00 R 5.00 0.50 0.00 7 + 0.00 0 20 40 60 80 100 0 10 20 30 40 50 60 T0 2{mm} 2{mm] _——analytical Deviation from Isotropyin Liquid 1.0 0.8 0.6 0.4 0.2 Z7 Axis 0.0 —0.2 —0.4 150 30 4\'4*‘ 200 20 :6 19 250 10 00 y 300 aso __° —1.0 —0.80 —060 —0.40 —0.20 0 020 040 060 0.80 10 Uncertainty of Spherical Isotropy Assessment: £3.2% (K=2) Certificate No: Z19—60101 Page 10 of 11

=—A® In Collaboration with ‘/"/‘/, s p e a q y CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Hittp://www.chinattl.en DASY/!EASY — Parameters of Probe: ES3DV3 — SN: 3090 Other Probe Parameters Sensor Arrangement Triangular Connector Angle (°) 1.2 Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disable Probe Overall Length 337mm Probe Body Diameter 10mm Tip Length 10mm Tip Diameter 4mm Probe Tip to Sensor X Calibration Point 2mm Probe Tip to Sensor Y Calibration Point 2mm Probe Tip to Sensor Z Calibration Point 2mm Recommended Measurement Distance from Surface 3mm Certificate No: Z19—60101 Page 11 of 11

} In Collabaration with s + BA iA 1i T"7/, s p e a 0 *A Rik®L caupration Lagoratory ififi CNAs o# Add: No.51 Xucyuan Road, Haidian District, Beijing, 100191, China %,"/%=~ s v eho Tel: +86—10—62304633—2079 Fax:+86—10—62304633—2504 "ll,m;\\“ CNAS LO570 E—mail: cttt@chinattl.com hitp://www.chinattl.on Client Hydsoft Testing Co., Ltd Certificate No: 218—60116 CALIBRATION CERTIFICATE Object D835V2 — SN: 40005 Calibration Procedure(s) FP—211—003—01 Calibration Procedures for dipole validation kits Calibration date: May 18, 2018 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(22#3)c and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRVD 102083 01—Nov—17 (CTTL, No.J17X08756) Oct—18 Power sensor NRV—Z5 100542 01—Nov—17 (CTTL, No.J17X08756) Oct—18 Reference Probe EX3DV4 SN 7464 12—Sep—17(SPEAG,No.EX3—7464_Sep17) Sep—18 DAE4 SN 1525 02—Oct—17(SPEAG,No.DAE4—1525_Oct17) Oct—18 Secondary Standards ID # Cal Date(Calibratedby, Certificate No.) Scheduled Calibration Signal Generator E4438C MY49071430 23—Jan—18 (CTTL, No.J18X00560) Jan—19 NetworkAnalyzer E5071C MY46110673 24—Jan—18 (CTTL, No.J18X00561) Jan—19 Name Function Signature Calibrated by: Zhao Jing SAR Test Engineer /g Z_/ Reviewed by: Lin Hao SAR Test Engineer T‘W}Tfi% Approved by: Qi Dianyuan SAR Project Leader %/ Issued: May 20, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: Z18—60116 Page 1 of 8

In Collabaration with ‘ . s_ _b ea _0 __, cAtipration LAcoratory Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Pax: +86—10—62304633—2504 E—mail: ettt@chinattl.com https//wwwehinattl.en Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORMx,y,z N/A not applicable or not measured Calibrationis Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for assessment of specific absorption rate of human exposure to radio frequency fields from hand—held and body—mounted wireless communication devices~ Part 1: Device used next to the ear (Frequency range of 300MHz to 6GHz)", July 2016 c) IEC 62209—2, "Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices usedin close proximily to the human body (frequency range of 30MHz to 6GHz)", March 2010 d) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Reportat the end of the certificate. All figures statedin the certificate are valid at the frequency indicated. e Antenna Parameters with TSL.: The dipole is mounted with the spacerto positionits feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned underthe liquidfilled phantom. The impedance statedis transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay betweenthe SMA connector and the antenna feed point. No uncertainty required. e SAR measured: SAR measuredat the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. o SAR for nominal TSL parameters: The measured TSL. parameters are usedto calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. Certificate No: Z18—60116 Page 2 of 8

In Collaboration with ‘i T TL se_(___ CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—6230—1633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com hittps//www.chinattl.en Measurement Conditions DASY system configuration, as far as not given on page 1. _ DASY Version DASY52 52.10.0.1446 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom5.1C Distance Dipole Center— TSL. 15 mm with Spacer Zoom Scan Resolution dx, dy, dz = 5 mm Frequency 835 MHz & 1 MHz Head TSL parameters The following parameters andcalculations were applied. Temperature Permitivity Conductivity Nominal Head TSL parametors 22.0 °C 41.5 0.90 mho/m Measured Head TSL parametors (22.0 £ 0.2) °C 42.1 x 6 % 0.88 mho/m * 6 % Head TSL temporature change during tost <1.0 °C SAR result with Head TSL SAR averagedover 1_cn" (1 g) of Hoad TSl. Condition SAR measured 250 mW input power 2.31 mW/g SAR for nominal Head TSL parameters normalizedto 1W 9.45 mW 7g * 18.8 % (Ie2) SAR averaged over 10 cm (10 g) of Head TSL Condition SAR measured 250 mW input power 147 mW/g SAR for nominal Head TSL parameters normalizedto 1W 5. 98 mW 1g & 18.7 % (k=2) Body TSL parameters The following parameters and calculations were applied. Tomperature Permittivity Conductivity Nominal Body TSL. parametors 22.0 °C 55.2 0.97 mho/m Measured Body TSI. paramoters (22.0 £ 0.2) °C 64.3 £ 6 % 0.95 mho/m x 6 % Body TSL temperature change during tost <1.0 °C SAR result with Body TSL SAR averagedover 1 cm" (1 g) of Body TSL Condition SAR measured 250 mW input power 241 mW/g SAR for nominal Body TSL parameters normalizedto 1W 9. 74 mW 1g # 18.8 % (Ic=2) SAR averaged over 10 cm* (10 g) of Body TSL Condition SAR measured 250 mW input power 1.57 mW/g SAR for nominal Body TSL parameters normalized to 1W 6.34 mW ig & 18.7 % (Ik=2) Certificate No: Z18—60116 Page 3 of 8

In Collabarati sp_ e_a___, ‘ cALIBRATION LAgoRATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62301633—2501 E—mail: ettt@chinattl.com https//www.chinattl.en Appendix (Additional assessments outsicde the scope of CNAS 1.0570) Antenna Parameters with Head TSL Impedance, transformedto feed point 49.50— 1.89J0 Return Loss —34.10B Antenna Parameters with Body TSL Impedance, transformedto feed point 46.60— 6.78J0 Return Loss —22.10B General Antenna Parameters and Design Electrical Delay (one direction) 1.257 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connectedto the secondarmof the dipole. The antenna is therefore short—circuitedfor DC—signals. On some of the dipoles, small end caps are addedto the dipole arms in order to improve matching when loaded according to the position as explainedin the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bendor the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z18—60116 Page 4 of8

In Collabaration with T"V‘/ . s p e a g “— CALIRRATION LARORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62301633—2501 E—mail: ett!@chinattl.com httpo//www.chinatt.en DASY5 Validation Report for Head TSL Date: 05.17.2018 Test Laboratory: CTTL, Beijing, China DUT: Dipole 835 MHz; Type: D835V2; Serial: D835V2 — SN: 44005 Communication System: UID 0, CW; Frequency: 835 MHz; Duty Cycle: 1:1 Medium parameters used: [= 835 MHz; 0 = 0.881 $/m; & =42.71; p= 1000 kg/m" Phantomsection: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI €63.19—2007) DASY5 Configuration: e Probe: EX3DV4 — SN7464; ConvF(10.28, 10.28, 10.28); Calibrated: 9/12/2017; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn1525; Calibrated: 10/2/2017 * Phantom: Triple Flat Phantom5.1C; Type: QD 000 PS1 CA; Serial: 116171 e Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) Dipole Calibration/Zoom Sean (7x7x7) (7x7x7)/Cube 0; Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 59.63 V/m; Power Drift =—0.06 dB Peak SAR (extrapolated) = 3.72 W/kg SAR(I g)=2.31 W/kg; SAR(10 g) = 1.47 W/kg Maximum value of SAR (measured) =3.21 W/kg 0 dB =3.21 W/kg = 5.07 dBW/kg Certificate No: Z18—60116 Page 5 of 8

m In Collabaration with T"T / s_p e a _g CALIBRATION LARORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—6230—41633—2079 Fax: +86—10—62301633—2501 E—mail: ettt@chinattl.com hitps/www.chinattl.en Impedance Measurement Plot for Head TSL Tri S11 tog Mag 10,00d8/ ref 0,000d[F1} +990 r53~835,00000 hiz ~34.076 do 40.00 30.00 2000 10.00 0,000 —10.00 *T x —20.00 —30.00 —40, 00 ~50. 00 — " C —al DfGB] S11 saith (Rijx) scale 1.000u [FL bel) >A 835.00000 miiz 49.458 0 »A.89M4 0 100.77—pF" 1<’h\ r.._._* // 1 Stort 635 MHr IFBWY100 He Stop 1.035 Gttz 1 Certificate No: Z18—60116 Page 6 of 8

In Collaboration with T"7‘/, s p e a g mss CAUIBRATION LAUORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—6230—41633—2504 E—mail: ett!@chinattl.com https//www.chinattl.en DASY5 Validation Report for Body TSL Date: 05.16.2018 Test Laboratory: CTTL, Beijing, China DUT: Dipole 835 MHz; Type: D835V2; Serial: D835V2 — SN: 40005 Communication System: UID 0, CW; Frequency: 835 MHz; Duty Cyele: 1:1 Medium parameters used: f= 835 MHz; o = 0.952 $/m; &, = 54.34; p = 1000 kg/m3 Phantomsection: Center Section Measurement Standard: DASYS (IEEE/IEC/ANSI €63.19—2007) DASY5 Configuration: e Probe: EX3DV4 — SN7464; ConvF(10.21, 10.21, 10.21); Calibrated: 9/12/2017; e Sensor—Surface: 1.4mim(Mechanical Surface Detection) e Electronics: DAEA4 Sn1525; Calibrated: 10/2/2017 e Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 116171 e Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) Dipole Calibration/Zoom Scan(7x7x7) (7x7x7)/Cube 0; Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 54.99 V/m; Power Drift =—0.05 dB Peak SAR (extrapolated) = 3.74 W/kg SAR(I g)=2.41 W/kg; SAR(10 g)= 1.57 W/kg Maximum value of SAR (measured) = 3.28 W/kg dB 210 4.36 +6.54 ~8.12 0 dB =3.28 W/kg = 5.16 dBW/kg Certificate No: Z18—60116 Page 7 of 8

m In Collaboration with T"/‘7, a s_p 7 Y i > CALIRRATION LARORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com hittp:/wwwchinattl.en Impedance Measurement Plot for Body TSL Tri S11 tog flag 10.00d8/ ReF 0.000d0 [r1} so. 00 31— 835.00000 tmz —22.149 do — 40. 00 20.00 20. 00 10.00 o 0.000 2 — , e . esb ce —10.00 $ » —20.00 \/ ~30, 00 —40. 00 ~50, 00 —— a._.—. % PSX s11 satch (m}x) scale 1.000u [F1 bel) CC 10 $35,.00000 fink 46.638 0 ~6.7757 n 28. l/u pFCo 1 Start 655 Mi BW100 ho Step noss ctte [NWl 1 Certificate No: Z18—60116 Page 8 of 8

Justification for Extended SAR Dipole Calibrations Date of Return Loss Dipole Delta (%) Impedance Delta(ohm) Measurement (dB) May 18, 2018 -34.1 - 49.5 - Head 835 MHz Apr. 17, 2019 -33.6 -1.47 46.2 -3.3 Note: The return loss is <-20dB, within 20% of prior calibration; the impedance is within 5 ohm of prior calibration. Therefore the verification results meet the requirement of extended calibration.

Justification for Extended SAR Dipole Calibrations Date of Return Loss Dipole Delta (%) Impedance Delta(ohm) Measurement (dB) May 18, 2018 -22.1 - 46.6 - Body 835 MHz Apr. 17, 2019 -22.2 0.45 46.0 -0.6 Note: The return loss is <-20dB, within 20% of prior calibration; the impedance is within 5 ohm of prior calibration. Therefore the verification results meet the requirement of extended calibration.

!&‘&‘m, ® In Collaboration with P ~, *¥ 4Amf m‘}"}‘}, _ m Y Y cipaggesss CALIBRATION LABORATORY EF’WE‘* Add: No.5 1 Xueyuan Road, Haidian District, Beijing, 100191, China "/,,/_\g< CALIBRATION Teh +86—10—62304633—2079 Fas: +86—10—62304633—2504 ’//,,/,,;,,\\\\ CNAS LO570 E—mail: ctt|@chinattl.com httpfwwnchinattLen Cenrtificate No: 218—60118 Object D1750V2 — SN: 1086 Calibration Procedure(s) FF:211—003—01. Calibration Procedures for dipole validation kits Calibration date: May 18, 2018 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(@243)‘C and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRVD 102083 O1—Nov—17 (CTTL, No.J17X08758) Oct—18 Power sensor NRV—Z56 100542 O1—Nov~17 (CTTL, No.J17X08756) Oct—18 Reference Probe EX3DV4 SN 7464 12—Sep—17(SPEAG,No.EX3—7464_Sep17) Sep—18 DAE4 SN 1525 02—Oct—17(SPEAG,N0.DAE4—1525_Oct17) Oct—18 Secondary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Signal Generator E4438C MY49071430 23—Jan—18 (CTTL, No.J18X00560) Jan—19 NetworkAnalyzer E50741C MY46110873 24—Jan—18 (CTTL, No.J18X00561) Jan—19 Function _ _ Signatc re ; y s Lo9 e . P Calibrated by: Reviewed by: Lin Hao Approved by: : Ql Dienyuan. ‘SARProject Leader * *‘ Issued: May 20, 2018 This callbration certificate shall not be reproduced except In full without written approval of the laboratory. Certificate No: Z18—60118 Page 1 of 8

a77), p_e —mmgss=>...©* In Colfaberation with We CALIBRATION LARORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, L00191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hittp/www.chinattlon Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORMx,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) |EEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for assessment of specific absorption rate of human exposure to radio frequency fields from hand—held and body—mounted wireless communication devices— Part 1: Device used next to the ear (Frequency range of 300MHz to 6GHz)", July 2016 c} IEC 62209—2, "Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices used in close proximity to the human body (frequency range of 30MHz to 6GHz)", March 2010 d) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the fiat phantom section, with the arms oriented paralle! to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. Certificate No: Z18—60118 Page 2 of 8

it.8 In Collaboration with aae‘// "// //, e v/ CALIBRATION LABORATORY Add; No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ctt@chinaltl.com hitp/wwwss.chinattlen Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Verslon DASY52 52.10.0.1446 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom 5.1C —__| Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz = 5 mm LFrequency 1750 MHz £ 1 MHz ___] Head TSL parameters ‘The following parameters and calculations were applied. Temporature Permlttivity Conductivity Nominal Head TSL parameters 22.0 °C 40.1 1.37 mho/m Measured Head TSL paramaters (22.0 £ 0.2) °C 40.7 £ 6 % 1.33 mho/m £8 % Head TSL temperature change during test <1.0 °C SAR result with Head TSL SAR averaged over 1_cn1" _(1 g) of Head TSL Condition SAR measured 250 mW input power 9.03 mW /g SAR for nominal Head TSL parameters normalized to 1W 36.9 mW /ig £ 18.8 % (k=2)_{ SAR averaged over 10 en‘ {10 g) of Head TSL Condition SAR measured 250 mW input power 4.74 mW 1 g SAR for nominal Head TSL parameters normalized to 1W 19.2 mW ig £18.7 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity ( Conductlvity ——]| Nominal Body TSL parameters 22.0 °C 53.4 1.49 mho/m Measured Body TSL parameters | croso2)°‘c 52.0 £ 6 % 145 mho/m £ 6 % Body TSL temperature change during test <1.0 °C SAR result with Body TSL SAR averaged over 1 cm (1 g) of Body TSL Condition SAR measured 250 mW Input power 9.32 mW /g SAR for nominal Body TSL paramsters normalized to 1W 37.6 mW (g 4 18.8 % (k=2) SAR averaged over 10 cm" (10 g) of Body TSL Condition SAR measured \‘ 250 mW input power 4.92 mW 1g SAR for nominal Body TSL parameters normalized to 1W 19.8 mW ig £ 18.7 % (ke2) Certificate No: Z18—60118 Page 3 of 8

ailillii®®®. 8 n Collshoration with a_‘/"/‘}, _p__e_ =1‘Py/ CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fox: +86—10—62304633—2504 E—mail: ett{@chinattl.com hitpul/wwo.chinattLen Appendix (Additional assessments outside the scope of CNAS LO570) Antenna Parameters with Head TSL Impedance, fransformed to feed point 48.30+ 2.80 JQ Retur Loss —29.4 dB Antenna Parameters with Body TSL tmpedance, transformed to feed point 45.00— 1.99 JQ Relurn Loss —24.9 dB General Antenna Parameters and Design ’Eacm'cal Delay (one direction) 1.126 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm ofthe dipole. The antenna is therefore short—clreuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph, The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z18—60118 Page 4 of 8

‘Q’i‘\ +s $ In Collebaration with ‘}"}/"‘}/, 'T’l‘w,/ _ CALIBRATION LABORATORY Add: No,51 Xueyuan Road, Haidian District, Beijing, 100191, China ‘Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ctt@chinaftl.com hittpuffwiwns.chinattl.on DASY5 Validation Report for Head TSL Date: 05,18.2018 Test Laboratory: CTTL, Beijing, China DUT: Dipole 1750 MHz; Type: D1750V2; Scrial; D1750V2 — SN; 1086 Communication System: UID 0, CW; Frequency: 1750 MHz; Duty Cycle: 1:1 Medium parameters used: £= 1750 MHz; 0 = 1.33 S/m; sr = 40.7; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI €63.19—2007) DASYS Configuration: e Probe: EX3DV4 — SN7464; ConvF(8.7, 8.7, 8.7); Calibrated: 9/12/2017; e Sensor—Surface: 1.4mim(Mechanical Surface Detection) * Electronics; DAE4 Sn1525; Calibrated: 10/2/2017 «_ Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P5L CA; Serial: 116171 & Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.(0 (7417) System Performance Check/Zoom Sean (7x7x7) (7x7x7)/Cube 0; Measurement grid: dx=5mm, dy=Smm, dz=$mm Reference Value = 97.86 V/m; Power Drift= 0.05 dB Peak SAR (extrapolated) = 17.4 W/kg SAR(I g)=9.03 W/kg; SAR(IO g) =4.74 Wikg Maximumvalue of SAR (measured)= 14.3 W/kg ————————— 0 dB = 14.3 W/kg = 11.55 dBW/kg Certificate No: Z18—60118 Page 5 of 8

mt> in Coltaboration with @ 4/+ . mg‘/"~"/‘/, c %‘J CALIBRATION LABORATORY Add: No.51 Xucyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail; cttt@chinattl.com hltpi//wws.chinatiLon Impedance Measurement Plot for Head TSL MTFI 311tog fiag 10. 00d8/ Ref 0. 00006 [F1] 5990 154127500000 aliz =29. 428 do 40.00 30.00 20,00 10, 00 0.000 p) d 10200 or———_ ‘N»\‘ fi At —20.00 ‘ — — 1/’ — ~30.00 < j ~40.00 —50.00 x smith (R+JX) scale 1,000U [F1 bel} »1 1.7300000 Giz 48.340 o 28786 0 261. 73—pH ‘ Certificate No: Z18—60118 Page 6 of 8

Qf'; «8 In Collaboration with a‘}/"}‘/, _3 %/ CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: eltl@chinattl.com hitp/wwiw.chioattl.en DASYS Validation Report for Body TSL Date: 05.16.2018 Test Laboratory: CTTL, Beijing, China DUT: Dipole 1750 MHz; Type: D1750V2; Serial: D1750V2 — SN: 1086 Communication System: UID 0, CW; Frequency: 1750 MHz; Duty Cyele: 1:1 Medium parameters used; £= 1750 MHz; 0 = L452 S/m; e = 51.98; p = 1000 kg/m3 Phantom section; Center Section Measurement Standard; DASYS (IEEE/IEC/ANSI C63.19—2007) DASY5 Configuration: * Probe; EX3DV4 « SN7464; ConyF($.6, 8.6, 8.6); Calibrated: 9/12/2017; e Sensor—Surface; 1.4min (Mechanical Surface Detection) + Electronics: DAE4 $n1525; Calibrated: 10/2/2017 + Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1 16171 e Measurement SW; DASY52, Version 52.10 (0) SEMCAD X Version 14.6.10 (7417) SystemPerformance Check/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measucement grid: dx=5mm, dy=5mm, dz=5mm Reforence Value = 85.43 V/m; Power Drift=—0.07 dB Peak SAR (extrapolated) = 17.1 W/kg SAR(1 g)=9.32 W/kg; SAR(IO g) =4.92 W/kg Maximum value of SAR (measured) = 14.4 W/kg 0 dB = 14.4 W/kg =11.58 dBW/kg Certificate No: Z18—60118 Page 7 of 8

In Collsboration with TV"7 7, _ %-‘w/ CALIBRATION LABGRATORY Add: No.51 Xucyan Road, Haidian Distriet, Beifing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: citt@chinatil.com httpi/www.chinalt.cn Impedance Measurement Plot for Body TSL Tr si1 Log Hay 10. 60de/ ref 0. dande (H) 5900 5217500000 onz 324. 893 an 40. 00 30.00 20,00 10.00 ~50,00 PM 511 seith (Re]x) scale 1.000U (Fi brl) »2 1,7500000 lfr 44.973 n —1.9937 0 45.616—pF° _ Certificate No: Z18—60118 Page & of 8


Document Created: 2019-08-27 17:18:29
Document Modified: 2019-08-27 17:18:29
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC