Test Report (2 of 2)

FCC ID: 2AFWN-SLG-CP101

Test Report

Download: PDF
FCCID_3497182

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 3.5 Unwanted Emissions (Radiated) ▣ Test Requirements and limit, §15.247(d), §15.205, §15.209 & RSS-247 [5.5], RSS-Gen [8.9], RSS-Gen [8.10] In any 100 kHz bandwidth outside the operating frequency band. In case the emission fall within the restricted band specified on 15.205(a) and (b), then the 15.209(a) limit in the table below has to be followed ▪ FCC Part 15.209(a) and (b) Frequency (MHz) Limit (uV/m) Measurement Distance (meter) 0.009 ~ 0.490 2400/F (kHz) 300 0.490 ~ 1.705 24000/F (kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 ** 3 88 ~ 216 150 ** 3 216 ~ 960 200 ** 3 Above 960 500 3 ** Except as provided in 15.209(g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54 ~ 72 MHz, 76 ~ 88 MHz, 174 ~ 216 MHz or 470 ~ 806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g. 15.231 and 15.241. ▪ FCC Part 15.205 (a) : Only spurious emissions are permitted in any of the frequency bands listed below : MHz MHz MHz MHz GHz GHz 0.009 ~ 0.110 8.41425 ~ 8.41475 108 ~ 121.94 1300 ~ 1427 4.5 ~ 5.15 14.47 ~ 14.5 0.495 ~ 0.505 12.29 ~ 12.293 123 ~ 138 1435 ~ 1626.5 5.35 ~ 5.46 15.35 ~ 16.2 2.1735 ~ 2.1905 12.51975 ~ 149.9 ~ 150.05 1645.5 ~ 1646.5 7.25 ~ 7.75 17.7 ~ 21.4 4.125 ~ 4.128 12.52025 156.52475 ~ 1660 ~ 1710 8.025 ~ 8.5 22.01 ~ 23.12 4.17725 ~ 4.17775 12.57675 ~ 156.52525 1718.8 ~ 1722.2 9.0 ~ 9.2 23.6 ~ 24.0 4.20725 ~ 4.20775 12.57725 156.7 ~ 156.9 2200 ~ 2300 9.3 ~ 9.5 31.2 ~ 31.8 6.215 ~ 6.218 13.36 ~ 13.41 162.0125 ~ 167.17 2310 ~ 2390 10.6 ~ 12.7 36.43 ~ 36.5 6.26775 ~ 6.26825 16.42 ~ 16.423 167.72 ~ 173.2 2483.5 ~ 2500 13.25 ~ 13.4 Above 38.6 6.31175 ~ 6.31225 16.69475 ~ 240 ~ 285 2655 ~ 2900 8.291 ~ 8.294 16.69525 322 ~ 335.4 3260 ~ 3267 8.362 ~ 8.366 16.80425 ~ 399.90 ~ 410 3332 ~ 3339 8.37625 ~ 8.38675 16.80475 608 ~ 614 3345.8 ~ 3358 25.5 ~ 25.67 960 ~ 1240 3600 ~ 4400 37.5 ~ 38.25 73 ~ 74.6 74.8 ~ 75.2 ▪ FCC Part 15.205(b) : The field strength of emissions appearing within these frequency bands shall not exceed the limits shown in §15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in §15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in §15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in §15.35 apply to these measurements. TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 41 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 3.5.1 Test Setup Refer to the APPENDIX I. 3.5.2 Test Procedures 1. The EUT is placed on a non-conductive table. For emission measurements at or below 1 GHz, the table height is 80 cm. For emission measurements above 1 GHz, the table height is 1.5 m. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 1 or 3 m away from the receiving antenna, which is varied from 1 m to 4 m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Repeat above procedures until the measurements for all frequencies are complete. Note: Measurement Instrument Setting for Radiated Emission Measurements. 1. Frequency Range: ≤ 1 GHz RBW = 100 or 120 kHz, VBW = 3 x RBW, Detector = Peak or Quasi Peak 2. Frequency Range: > 1 GHz Peak Measurement RBW = 1 MHz, VBW = 3 MHz, Detector = Peak, Sweep time = Auto, Trace mode = Max Hold until the trace stabilizes Average Measurement The result of Average measurement was calculated using PK result and duty cycle reduction factor. (The Peak measurement was performed at 100% duty cycle. But, this device has a low duty cycle when actual operation.) Note: Refer to appendix II for duty cycle correction factor. TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 42 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 3.5.3 Test Results Test Mode: TM 1 Frequency Range : 9 kHz ~ 25 GHz ▪ Lowest Channel Distance Frequency ANT EUT Position Detector Reading T.F D.C.F Result Limit Margin Factor (MHz) Pol (Axis) Mode (dBuV) (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) 2388.62 V Y PK 50.03 0.77 N/A N/A 50.80 74.00 23.20 2388.62 V Y AV 50.03 0.77 -33.98 N/A 16.82 54.00 37.18 4809.72 H Y PK 44.15 7.62 N/A N/A 51.77 74.00 22.23 4809.72 H Y AV 44.15 7.62 -33.98 N/A 17.79 54.00 36.21 ▪ Middle Channel Frequency ANT EUT Position Detector Reading T.F D.C.F Distance Result Limit Margin (MHz) Pol (Axis) Mode (dBuV) (dB/m) (dB) Factor(dB) (dBuV/m) (dBuV/m) (dB) 4880.63 H Y PK 44.40 7.34 N/A N/A 51.74 74.00 22.26 4880.63 H Y AV 44.40 7.34 -33.98 N/A 17.76 54.00 36.24 ▪ Highest Channel Distance Frequency ANT EUT Position Detector Reading T.F D.C.F Result Limit Margin Factor (MHz) Pol (Axis) Mode (dBuV) (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) 2483.54 V Y PK 58.32 1.10 N/A N/A 59.42 74.00 14.58 2483.54 V Y AV 58.32 1.10 -33.98 N/A 25.44 54.00 28.56 4960.69 H Y PK 43.96 7.47 N/A N/A 51.43 74.00 22.57 4960.69 H Y AV 43.96 7.47 -33.98 N/A 17.45 54.00 36.55 ▪ Note. 1. No other spurious and harmonic emissions were found greater than listed emissions on above table. 2. Information of Distance Factor For finding emissions, the test distance might be reduced from 3 m to 1 m. In this case, the distance factor(-9.54 dB) is applied to the result. - Calculation of distance factor = 20 log( applied distance / required distance ) = 20 log( 1 m / 3 m ) = -9.54 dB When distance factor is “N/A”, the distance is 3 m and distance factor is not applied. 3. Sample Calculation. Margin = Limit – Result / Result = Reading + T.F + D.C.F / T.F = AF + CL – AG Where, T.F = Total Factor, AF = Antenna Factor, CL = Cable Loss, AG = Amplifier Gain, DCF = Duty Cycle Correction Factor. TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 43 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 Test Mode: TM 2 Frequency Range : 9 kHz ~ 25 GHz ▪ Lowest Channel Distance Frequency ANT EUT Position Detector Reading T.F D.C.F Result Limit Margin Factor (MHz) Pol (Axis) Mode (dBuV) (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) 2389.68 H Z PK 49.29 0.78 N/A N/A 50.07 74.00 23.93 2389.68 H Z AV 49.29 0.78 -4.98 N/A 45.09 54.00 8.91 4809.24 H Y PK 43.88 7.62 N/A N/A 51.50 74.00 22.50 4809.24 H Y AV 43.88 7.62 -4.98 N/A 46.52 54.00 7.48 ▪ Middle Channel Frequency ANT EUT Position Detector Reading T.F D.C.F Distance Result Limit Margin (MHz) Pol (Axis) Mode (dBuV) (dB/m) (dB) Factor(dB) (dBuV/m) (dBuV/m) (dB) 4881.80 H Y PK 44.85 7.31 N/A N/A 52.16 74.00 21.84 4881.80 H Y AV 44.85 7.31 -4.98 N/A 47.18 54.00 6.82 ▪ Highest Channel Distance Frequency ANT EUT Position Detector Reading T.F D.C.F Result Limit Margin Factor (MHz) Pol (Axis) Mode (dBuV) (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) 2483.59 H Z PK 52.71 1.10 N/A N/A 53.81 74.00 20.19 2483.59 H Z AV 52.71 1.10 -4.98 N/A 48.83 54.00 5.17 4961.14 H Y PK 44.46 7.47 N/A N/A 51.93 74.00 22.07 4961.14 H Y AV 44.46 7.47 -4.98 N/A 46.95 54.00 7.05 ▪ Note. 1. No other spurious and harmonic emissions were found greater than listed emissions on above table. 2. Information of Distance Factor For finding emissions, the test distance might be reduced from 3 m to 1 m. In this case, the distance factor(-9.54 dB) is applied to the result. - Calculation of distance factor = 20 log( applied distance / required distance ) = 20 log( 1 m / 3 m ) = -9.54 dB When distance factor is “N/A”, the distance is 3 m and distance factor is not applied. 3. Sample Calculation. Margin = Limit – Result / Result = Reading + T.F + D.C.F / T.F = AF + CL – AG Where, T.F = Total Factor, AF = Antenna Factor, CL = Cable Loss, AG = Amplifier Gain, DCF = Duty Cycle Correction reduction Factor. TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 44 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 Test Mode: TM 3 Frequency Range : 9 kHz ~ 25 GHz ▪ Lowest Channel Distance Frequency ANT EUT Position Detector Reading T.F D.C.F Result Limit Margin Factor (MHz) Pol (Axis) Mode (dBuV) (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) 2386.94 V Y PK 50.64 0.77 N/A N/A 51.41 74.00 22.59 2386.94 V Y AV 50.64 0.77 -33.98 N/A 17.43 54.00 36.57 4810.38 H Y PK 44.49 7.62 N/A N/A 52.11 74.00 21.89 4810.38 H Y AV 44.49 7.62 -33.98 N/A 18.13 54.00 35.87 ▪ Middle Channel Frequency ANT EUT Position Detector Reading T.F D.C.F Distance Result Limit Margin (MHz) Pol (Axis) Mode (dBuV) (dB/m) (dB) Factor(dB) (dBuV/m) (dBuV/m) (dB) 4878.81 H Y PK 44.53 7.34 N/A N/A 51.87 74.00 22.13 4878.81 H Y AV 44.53 7.34 -33.98 N/A 17.89 54.00 36.11 ▪ Highest Channel Distance Frequency ANT EUT Position Detector Reading T.F D.C.F Result Limit Margin Factor (MHz) Pol (Axis) Mode (dBuV) (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) 2483.53 V Y PK 58.01 1.10 N/A N/A 59.11 74.00 14.89 2483.53 V Y AV 58.01 1.10 -33.98 N/A 25.13 54.00 28.87 4959.34 H Y PK 44.05 7.47 N/A N/A 51.52 74.00 22.48 4959.34 H Y AV 44.05 7.47 -33.98 N/A 17.54 54.00 36.46 ▪ Note. 1. No other spurious and harmonic emissions were found greater than listed emissions on above table. 2. Information of Distance Factor For finding emissions, the test distance might be reduced from 3 m to 1 m. In this case, the distance factor(-9.54 dB) is applied to the result. - Calculation of distance factor = 20 log( applied distance / required distance ) = 20 log( 1 m / 3 m ) = -9.54 dB When distance factor is “N/A”, the distance is 3 m and distance factor is not applied. 3. Sample Calculation. Margin = Limit – Result / Result = Reading + T.F + D.C.F / T.F = AF + CL – AG Where, T.F = Total Factor, AF = Antenna Factor, CL = Cable Loss, AG = Amplifier Gain, DCF = Duty Cycle Correction reduction Factor. TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 45 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 Test Mode: TM 4 Frequency Range : 9 kHz ~ 25 GHz ▪ Lowest Channel Distance Frequency ANT EUT Position Detector Reading T.F D.C.F Result Limit Margin Factor (MHz) Pol (Axis) Mode (dBuV) (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) 2386.94 H Z PK 49.07 0.77 N/A N/A 49.84 74.00 24.16 2386.94 H Z AV 49.07 0.77 -4.98 N/A 44.86 54.00 9.14 4810.54 H Y PK 44.20 7.62 N/A N/A 51.82 74.00 22.18 4810.54 H Y AV 44.20 7.62 -4.98 N/A 46.84 54.00 7.16 ▪ Middle Channel Frequency ANT EUT Position Detector Reading T.F D.C.F Distance Result Limit Margin (MHz) Pol (Axis) Mode (dBuV) (dB/m) (dB) Factor(dB) (dBuV/m) (dBuV/m) (dB) 4879.70 H Y PK 44.42 7.34 N/A N/A 51.76 74.00 22.24 4879.70 H Y AV 44.42 7.34 -4.98 N/A 46.78 54.00 7.22 ▪ Highest Channel Distance Frequency ANT EUT Position Detector Reading T.F D.C.F Result Limit Margin Factor (MHz) Pol (Axis) Mode (dBuV) (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) 2483.50 H Z PK 52.83 1.10 N/A N/A 53.93 74.00 20.07 2483.50 H Z AV 52.83 1.10 -4.98 N/A 48.95 54.00 5.05 4959.33 H Y PK 44.20 7.47 N/A N/A 51.67 74.00 22.33 4959.33 H Y AV 44.20 7.47 -4.98 N/A 46.69 54.00 7.31 ▪ Note. 1. No other spurious and harmonic emissions were found greater than listed emissions on above table. 2. Information of Distance Factor For finding emissions, the test distance might be reduced from 3 m to 1 m. In this case, the distance factor(-9.54 dB) is applied to the result. - Calculation of distance factor = 20 log( applied distance / required distance ) = 20 log( 1 m / 3 m ) = -9.54 dB When distance factor is “N/A”, the distance is 3 m and distance factor is not applied. 3. Sample Calculation. Margin = Limit – Result / Result = Reading + T.F + D.C.F / T.F = AF + CL – AG Where, T.F = Total Factor, AF = Antenna Factor, CL = Cable Loss, AG = Amplifier Gain, DCF = Duty Cycle Correction reduction Factor. TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 46 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 3.6 Power line Conducted Emissions ▣ Test Requirements and limit, §15.207 & RSS-Gen [8.8] For an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies, within the band 150 kHz to 30 MHz, shall not exceed the limits in the following table, as measured using a 50 μH/50 ohms line impedance stabilization network (LISN). Conducted Limit (dBuV) Frequency Range (MHz) Quasi-Peak Average 0.15 ~ 0.5 66 to 56 * 56 to 46 * 0.5 ~ 5 56 46 5 ~ 30 60 50 * Decreases with the logarithm of the frequency Compliance with this provision shall be based on the measurement of the radio frequency voltage between each power line (LINE and NEUTRAL) and ground at the power terminals. 3.6.1 Test Setup See test photographs for the actual connections between EUT and support equipment. 3.6.2 Test Procedures Conducted emissions from the EUT were measured according to the ANSI C63.10. 1. The test procedure is performed in a 6.5 m × 3.5 m × 3.5 m (L × W × H) shielded room. The EUT along with its peripherals were placed on a 1.0 m (W) × 1.5 m (L) and 0.8 m in height wooden table and the EUT was adjusted to maintain a 0.4 meter space from a vertical reference plane. 2. The EUT was connected to power mains through a line impedance stabilization network (LISN) which provides 50 ohm coupling impedance for measuring instrument and the chassis ground was bounded to the horizontal ground plane of shielded room. 3. All peripherals were connected to the second LISN and the chassis ground also bounded to the horizontal ground plane of shielded room. 4. The excess power cable between the EUT and the LISN was bundled. The power cables of peripherals were unbundled. All connecting cables of EUT and peripherals were moved to find the maximum emission. Note: The worst data TM 3 was reported. Refer to the next page. TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 47 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 3.6.3 Test Results AC Line Conducted Emissions (Graph) = TM 3 & Test Channel : Middle TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 48 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 AC Line Conducted Emissions (List) = TM 3 & POE & Test Channel : Middle TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 49 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 3.7 Occupied Bandwidth ▣ Test Requirements, RSS-Gen [6.6] When an occupied bandwidth value is not specified in the applicable RSS, the transmitted signal bandwidth to be reported is to be its 99 % emission bandwidth, as calculated or measured. 3.7.1 Test Setup Refer to the APPENDIX I. 3.7.2 Test Procedures The 99 % power bandwidth was measured with a calibrated spectrum analyzer. The resolution bandwidth (RBW) shall be in the range of 1 % to 5 % of the occupied bandwidth (OBW) and video bandwidth (VBW) shall be approximately 3 × RBW. Spectrum analyzer plots are included on the following pages. 3.7.3 Test Results Test Mode Tested Channel Test Results (MHz) Lowest 2.015 TM 1 Middle 2.035 Highest 2.022 Lowest 2.002 TM 2 Middle 2.046 Highest 2.022 TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 50 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 Occupied Bandwidth (99 %) TM 1 & Test Channel : Lowest Occupied Bandwidth (99 %) TM 1 & Test Channel : Middle TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 51 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 Occupied Bandwidth (99 %) TM 1 & Test Channel : Highest TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 52 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 Occupied Bandwidth (99 %) TM 2 & Test Channel : Lowest Occupied Bandwidth (99 %) TM 2 & Test Channel : Middle TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 53 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 Occupied Bandwidth (99 %) TM 2 & Test Channel : Highest TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 54 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 4. ANTENNA REQUIREMENTS ▣ According to FCC 47 CFR §15.203 & RSS-Gen [8.3] “An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by the responsible party can be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section.” The internal antenna employs a unique antenna connector. Therefore this E.U.T Complies with the requirement of §15.203 TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 55 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 APPENDIX I Test set up diagrams ▪ Radiated Measurement Below 1GHz Above 1GHz For measurement below 30MHz, the proper calibration between the chamber and OATS has been done per KDB 937606. ▪ Conducted Measurement Path loss information Frequency (GHz) Path Loss (dB) Frequency (GHz) Path Loss (dB) 0.03 0.28 15 4.73 1 1.30 20 5.22 2.405 & 2.440 & 2.480 1.86 25 5.81 5 2.96 - - 10 3.41 - - Note 1: The path loss from EUT to Spectrum analyzer was measured and used for test. Path loss (S/A’s correction factor) = Cable A (Attenuator, Applied only when it was used externally) TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 56 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 APPENDIX II Duty cycle ▪ Test Procedure Duty Cycle was measured using section 6.0 b) of KDB558074 : The zero-span mode on a spectrum analyzer or EMI receiver if the response time and spacing between bins on the sweep are sufficient to permit accurate measurements of the on and off times of the transmitted signal. Set the center frequency of the instrument to the center frequency of the transmission. Set RBW ≥ OBW if possible; otherwise, set RBW to the largest available value. Set VBW ≥ RBW. Set detector = peak or average. The zero-span measurement method shall not be used unless both RBW and VBW are > 50/T and the number of sweep points across duration T exceeds 100. (For example, if VBW and/or RBW are limited to 3 MHz, then the zero-span method of measuring duty cycle shall not be used if T ≤ 16.7 microseconds.) TM 1 & Test Channel : Middle TM 2 & Test Channel : Middle Measured duty cycle under testing condition 100% Declared the max duty cycle under normal TM 1(Modem #2) 2.0% (1ms / 50 ms) operating condition (Transmit on time / period) Duty cycle reduction factor 20 x log (1ms/50ms) = -33.98 dB Measured duty cycle under testing condition 100% Declared the max duty cycle under normal TM 2(Modem #4) 56.3 % (4ms / 7.1ms) operating condition (Transmit on time / period) Duty cycle reduction factor 20 x log (4ms/7.1ms) = -4.98 dB Note: The worst case duty cycle has heen provided by the manufacturer’s technical documentation. TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 57 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 APPENDIX III Unwanted Emissions (Radiated) Test Plot TM 1 & Lowest & Y& Ver Detector Mode : PK TM 1 & Highest & Y & Ver Detector Mode : PK TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 58 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 TM 1 & Lowest & Y & Hor Detector Mode : PK TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 59 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 TM 2 & Lowest & Z & Hor Detector Mode : PK TM 2 & Highest & Z & Hor Detector Mode : PK TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 60 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 TM 2 & Middle & Y & Hor Detector Mode : PK TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 61 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 TM 3 & Lowest & Y & Ver Detector Mode : PK TM 3 & Highest & Y & Ver Detector Mode : PK TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 62 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 TM 3 & Middle & Y & Hor Detector Mode : PK TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 63 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 TM 4 & Lowest & Z & Hor Detector Mode : PK TM 4 & Highest & Z & Hor Detector Mode : PK TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 64 / 65

FCC ID: 2AFWN-SLG-CP101 Report No.: DRTFCC1707-0130(1) IC: 22800-SLGCP101 TM 4 & Highest & Y & Hor Detector Mode : PK TRF-RF-238(04)161101 Prohibits the copying and re-issue of this report without DT&C approval. Pages: 65 / 65


Document Created: 2017-08-04 09:20:57
Document Modified: 2017-08-04 09:20:57
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC