180424178GZU-001-reportR1_Security

FCC ID: 2AFT4-BPETO

Test Report

Download: PDF
FCCID_3951899

TXS Industrial Design Inc., dba Brandstand TEST REPORT SCOPE OF WORK EMC TESTING–BPETO REPORT NUMBER 180424178GZU-001 ISSUE DATE [REVISED DATE] 03-July-2018 [---------------------] PAGES 21 DOCUMENT CONTROL NUMBER FCC Part 15C -a © 2017 INTERTEK

Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD Guangzhou, China TEST REPORT Telephone: 86-20-8213 9688 Facsimile: 86-20-3205 7538 www.intertek.com Applicant Name & : TXS Industrial Design Inc. dba Brandstand Products Address 801 E. Campbell Road #620 Richardson, TX 75081 United States Manufacturing Site : Same as applicant Intertek Report No: 180424178GZU-001 FCC ID: 2AFT4-BPETO Test standards 47 CFR PART 15 Subpart C:2017 Sample Description Product : Cubietrio Model No. : BPETO Electrical Rating : Input: 125Vac, 60Hz USB Output: 5Vdc, 2.4A Wireless output: Up to 15W Serial No. Not Labeled Date Received : 24 April 2018 Date Test : 24 April 2018-02 July 2018 Conducted Prepared and Checked By Approved By: Daniel He Helen Ma Project Engineer Team Leader Intertek Guangzhou Intertek Guangzhou This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Version: 21 August 2017 Page 2 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT CONTENT TEST REPORT ........................................................................................................................... 1 CONTENT ............................................................................................................................. 3 1.0 TEST RESULT SUMMARY............................................................................................ 4 2.0 GENERAL DESCRIPTION ............................................................................................. 5 2.1 PRODUCT DESCRIPTION........................................................................................................ 5 2.2 RELATED SUBMITTAL(S) GRANTS ........................................................................................... 5 2.3 TEST METHODOLOGY .......................................................................................................... 5 2.4 TEST FACILITY ..................................................................................................................... 5 3.0 SYSTEM TEST CONFIGURATION ................................................................................. 6 3.1 JUSTIFICATION .................................................................................................................... 6 3.2 EUT EXERCISING SOFTWARE ................................................................................................. 7 3.3 SPECIAL ACCESSORIES .......................................................................................................... 7 3.4 MEASUREMENT UNCERTAINTY .............................................................................................. 7 3.5 EQUIPMENT MODIFICATION ................................................................................................. 8 3.6 SUPPORT EQUIPMENT LIST AND DESCRIPTION.......................................................................... 8 4.0 RADIATED EMISSION ................................................................................................. 9 5.0 CONDUCTED EMISSION TEST ................................................................................... 18 6.0 TEST EQUIPMENT LIST ............................................................................................. 21 Version: 21 August 2017 Page 3 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT 1.0 TEST RESULT SUMMARY Classification of EUT: Class B Test Item Test Requirement Test Method Result Conducted disturbance FCC PART 15 C ANSI C63.10: Clause 6.2 voltage at mains ports PASS section 15.207 FCC PART 15 C ANSI C63.10: Clause 6.4 & Radiated Emission PASS section 15.209 6.5 Remark: When determining the test results, measurement uncertainty of tests has been considered. Version: 21 August 2017 Page 4 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT 2.0 General Description 2.1 Product Description Operating Frequency 123-146KHz Type of Modulation: MSK Antenna Type Inductive loop coil antenna Antenna gain: 0 dBi Power Supply: Input: 125Vac, 60Hz USB Output: 5Vdc, 2.4A Wireless output: Up to 15W Power cord: 1.8m x 2 wires unscreened cable 2.2 Related Submittal(s) Grants This is an application for certification of: DCD-Part 15 Low Power Transmitter below 1705kHz Remaining portions are subject to the following procedures: The USB Charging function: tested together with wireless charger. 2.3 Test Methodology Both AC mains line-conducted and radiated emission measurements were performed according to the procedures in ANSI C63.10. Radiated emission measurement was performed in semi-anechoic chamber and conducted emission measurement was performed in shield room. For radiated emission measurement, preliminary scans and final tests were performed in the semi-anechoic chamber to determine the worst case modes. All radiated tests were performed at an antenna to EUT distance of 3 meters, unless stated otherwise. 2.4 Test Facility All tests were performed at: Room102/104, No 203, KeZhu Road, Science City, GETDD Guangzhou, China Except Conducted Emissions was performed at: Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD Guangzhou, China Version: 21 August 2017 Page 5 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT A2LA Certificate Number 0078.10 Intertek Testing Services Shenzhen Ltd. Guangzhou Branch is accredited by A2LA and Listed in FCC website. FCC accredited test labs may perform both Certification testing under Parts 15 and 18 and Declaration of Conformity testing. 3.0 System Test Configuration 3.1 Justification For emissions testing, the equipment under test (EUT) setup to transmit continuously to simplify the measurement methodology. Care was taken to ensure proper power supply voltages during testing. It was powered by AC 125V/60Hz supply. When below 30MHz, the measurement antenna was positioned with its plane perpendicular to the ground at the specified distance. When perpendicular to the ground plane, the lowest height of the magnetic antenna was 1 m above the ground and was positioned at 3m distance from the EUT. During testing the loop antenna was rotated about its vertical axis for maximum response at each azimuth and also investigated with the loop positioned in the horizontal plane. For each measurement antenna alignment, the EUT shall be rotated through 0° to 360° on a turntable. When above 30MHz, the antenna height and polarization are varied during the search for maximum signal level. The antenna height is varied from 1 to 4 meters. Radiated emissions are taken at three meters unless the signal level is too low for measurement at that distance. If necessary, a pre-amplifier is used and/or the test is conducted at a closer distance. All readings are extrapolated back to the equivalent three meter reading using inverse scaling with distance. The spurious emissions more than 20 dB below the permissible value are not reported. For an intentional radiator, the spectrum shall be investigated from the lowest radio frequency signal generated in the device, without going below 9 kHz, up to at least the frequency shown in the following table: Frequency range of radiated emission measurements Lowest frequency generated in the Upper frequency range of measurement device 10th harmonic of highest fundamental frequency or to 9 kHz to below 10 GHz 40 GHz, whichever is lower At or above 10 GHz to below 5th harmonic of highest fundamental frequency or to 30 GHz 100 GHz, whichever is lower 5th harmonic of highest fundamental frequency or to At or above 30 GHz 200 GHz, whichever is lower, unless otherwise specified Version: 21 August 2017 Page 6 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT Number of fundamental frequencies to be tested in EUT transmit band Frequency range in which device Number of Location in frequency operates frequencies range of operation 1 MHz or less 1 Middle 1 near top and 1 near 1 MHz to 10 MHz 2 bottom 1 near top, 1 near More than 10 MHz 3 middle and 1 near bottom 3.2 EUT Exercising Software N/A 3.3 Special Accessories N/A 3.4 Measurement Uncertainty No. Item Measurement Uncertainty 1 Conduction Emission (9 kHz-150 kHz) 2.51 dB 2 Conduction Emission (150 kHz-30 MHz) 2.69 dB 3 Disturbance Power (30 MHz-300 MHz) 3.21 dB 4 Radiated Emission (30 MHz-1 GHz) 4.79 dB 5 Radiated Emission (1 GHz-6 GHz) 5.02 dB 6 Radiated Emission (6 GHz-18 GHz) 5.17 dB The measurement uncertainty describes the overall uncertainty of the given measured value during the operation of the EUT. Measurement uncertainty is calculated in accordance with ETSI TR 100 028-2001. The measurement uncertainty is given with a confidence of 95%, k=2. When determining of the test conclusion, the Measurement Uncertainty of test has been considered. Uncertainty and Compliance – Unless the standard specifically states that measured values are to be extended by the measurement uncertainty in determining compliance, all compliance determinations are based on the actual measured value Version: 21 August 2017 Page 7 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT 3.5 Equipment Modification Any modifications installed previous to testing by TXS Industrial Design Inc., dba Brandstand Products will be incorporated in each production model sold / leased in the United States. No modifications were installed by Intertek Testing Services Shenzhen Ltd. Guangzhou Branch. 3.6 Support Equipment List and Description This product was tested with corresponding support equipment as below: Support Equipment: Equipment Model No. Rating Supplier Mobile phone LG V30+ -- Client Remark: the device will be sold with adaptor. To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested based on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above evaluated respectively Pre-test mode Description Standby Mode kept transmitting continuously CH: Low Mobile phone is charging at 1% battery Charging Mode CH: Middle power, 50% and 99% battery power CH: High respectively, keep transmitting continuously. For AC port Conducted Emission: Pre-test all modes listed above, find the worst case as: wireless charging at low channel for Mobile at 1% battery power with USB charging (full load). For Radiated Emission: Pre-test all modes listed above, find the worst case as: wireless charging at low channel for Mobile at 1% battery power with USB charging (full load). Version: 21 August 2017 Page 8 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT 4.0 Radiated Emission Test Requirement: FCC PART 15 C section 15.209 (a)(f) § 15.209 (a) Except as provided elsewhere in this subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency (MHz) Field Strength (dBµV/m @ 3m) 0.009-0.490 128-93.8 0.490-1.705 73.8-62.9 1.705-30.0 69.5 30-88 40 88-216 43.5 216-960 46 Above 960 54 (f) In accordance with §15.33(a), in some cases the emissions from an intentional radiator must be measured to beyond the tenth harmonic of the highest fundamental frequency designed to be emitted by the intentional radiator because of the incorporation of a digital device. If measurements above the tenth harmonic are so required, the radiated emissions above the tenth harmonic shall comply with the general radiated emission limits applicable to the incorporated digital device, as shown in §15.109 and as based on the frequency of the emission being measured, or, except for emissions contained in the restricted frequency bands shown in §15.205, the limit on spurious emissions specified for the intentional radiator, whichever is the higher limit. Emissions which must be measured above the tenth harmonic of the highest fundamental frequency designed to be emitted by the intentional radiator and which fall within the restricted bands shall comply with the general radiated emission limits in §15.109 that are applicable to the incorporated digital device. Test Method: ANSI C63.10: Clause 6.4 and 6.5. Test Status: Pre-Scan has been conducted to determine the worst-case mode from all possible configuration. Test site: Measurement Distance: 3m (Semi-Anechoic Chamber) Detector: Quasi-Peak detector: RBW=200 Hz for 9 kHz to 150 kHz RBW=9 kHz for 150 kHz to 30 MHz Version: 21 August 2017 Page 9 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT RBW=120 kHz for 30 MHz to 1GHz Sweep = auto Trace = max hold Field Strength Calculation: The field strength is calculated by adding the reading on the Spectrum Analyzer to the factors associated with preamplifiers (if any), antennas, cables, pulse desensitization and average factors (when specified limit is in average and measurements are made with peak detectors). A sample calculation is included below: FS = RA + AF + CF - AG + PD + AV FS = RA + Correct Factor + AV FS = Field Strength in dBµV/m Where: RA = Receiver Amplitude (including preamplifier) in dBµV AF = Antenna Factor in dB CF = Cable Attenuation Factor in dB AG = Amplifier Gain in dB PD = Pulse Desensitization in dB AV = Average Factor in –dB Correct Factor = AF + CF – AG + PD In the radiated emission table which follows, the reading shown on the data table may reflect the preamplifier gain. An example of the calculations, where the reading does not reflect the preamplifier gain, follows: FS = RA + AF + CF - AG + PD + AV Assume a receiver reading of 62.0 dBµV is obtained. The antenna factor of 7.4 dB and cable factor of 1.6 dB is added. The amplifier gain of 29 dB is subtracted. The pulse desensitization factor of the spectrum analyzer was 0 dB, and the resultant average factor was - 10 dB. The net field strength for comparison to the appropriate emission limit is 32 dBµV/m. RA = 62.0 dBµV AF = 7.4 dB CF = 1.6 dB AG = 29.0 dB PD = 0 dB AV = -10 dB Correct Factor = 7.4 + 1.6 – 29.0 + 0 = -20 dB FS = 62 + (-20) + (-10) = 32 dBµV/m Version: 21 August 2017 Page 10 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT Section 15.205 Restricted bands of operation. MHz MHz MHz GHz 0.090 - 0.110 16.42 - 16.423 399.9 - 410 4.5 - 5.15 1 0.495 - 0.505 16.69475 - 16.69525 608 - 614 5.35 - 5.46 2.1735 - 2.1905 16.80425 - 16.80475 960 - 1240 7.25 - 7.75 4.125 - 4.128 25.5 - 25.67 1300 - 1427 8.025 - 8.5 4.17725 - 4.17775 37.5 - 38.25 1435 - 1626.5 9.0 - 9.2 4.20725 - 4.20775 73 - 74.6 1645.5 - 1646.5 9.3 - 9.5 6.215 - 6.218 74.8 - 75.2 1660 - 1710 10.6 - 12.7 6.26775 - 6.26825 108 - 121.94 1718.8 - 1722.2 13.25 - 13.4 6.31175 - 6.31225 123 - 138 2200 - 2300 14.47 - 14.5 8.291 - 8.294 149.9 - 150.05 2310 - 2390 15.35 - 16.2 8.362 - 8.366 156.52475 - 2483.5 - 2500 17.7 - 21.4 8.37625 - 8.38675 156.52525 2655 - 2900 22.01 - 23.12 8.41425 - 8.41475 156.7 - 156.9 3260 - 3267 23.6 - 24.0 12.29 - 12.293 162.0125 - 167.17 3332 - 3339 31.2 - 31.8 12.51975 - 12.52025 167.72 - 173.2 3345.8 - 3358 36.43 - 36.5 12.57675 - 12.57725 240 - 285 3600 - 4400 13.36 - 13.41 322 - 335.4 The field strength of emissions appearing within these frequency bands shall not exceed the limits shown in 15.209. Version: 21 August 2017 Page 11 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT Test Configuration: 1) 9 kHz to 30 MHz emissions: 2) 30 MHz to 1 GHz emissions: Version: 21 August 2017 Page 12 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT Test Procedure: 1) 9 kHz to 30 MHz emissions: For testing performed with the loop antenna. The centre of the loop was positioned 1 m above the ground and positioned with its plane vertical at the special distance from the EUT. During testing the loop was rotated about its vertical axis for maximum response at each azimuth and also investigated with the loop positioned in the horizontal plane. 2) 30 MHz to 1 GHz emissions: For testing performed with the bi-log type antenna. The measurement is performed with the EUT rotated 360º, the antenna height scanned between 1m and 4m, and the antenna rotated to repeat the measurement for both the horizontal and vertical antenna polarizations. 3) The receiver was scanned from 9 kHz to 1 GHz. When an emission was found, the table was rotated to produce the maximum signal strength. An initial pre-scan was performed for in peak detection mode using the receiver. The EUT was measured for both the Horizontal and Vertical polarities and performed a pre-test three orthogonal planes. For intentional radiators, measurements of the variation of the input power or the radiated signal level of the fundamental frequency component of the emission, as appropriate, shall be performed with the supply voltage varied between 85% and 115% of the nominal rated supply voltage. The worst case emissions were reported. Used Test Equipment List: 3m Semi-Anechoic Chamber, EMI Test Receiver (9 kHz~7 GHz), Signal and Spectrum Analyzer (10 Hz~40 GHz), Loop antenna (9 kHz-30 MHz). TRILOG Super Broadband test Antenna(30 MHz- 3 GHz）(RX), Refer to Clause 4 Test Equipment List for details. Version: 21 August 2017 Page 13 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT Radiated Emissions (Below 30 MHz) Vertical: 189 180 160 140 120 100 dBµV/m Level in 80 FCC 15-9K-30MHz-wireless charging 60 40 20 0 9k 20 30 50 100k 200 300 500 1M 2M 3M 5M 10M 20 30M Frequency in Hz Correction Detector Frequency Read Margin Factor Level Limit (MHz) Level (dB) (dBμV/m) (dBμV/m) (dBμV) (dB) 0.128 69.7 20.6 90.3 105.4 15.1 PK 0.386 42.9 20.9 63.8 95.9 32.1 PK 0.638 32.2 21.3 53.5 71.5 18.0 PK 0.898 27.3 21.3 48.6 68.5 19.9 PK Version: 21 August 2017 Page 14 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT Horizontal: 189 180 160 140 120 100 dBµV/m Level in 80 FCC 15-9K-30MHz-wireless charging 60 40 20 0 9k 20 30 50 100k 200 300 500 1M 2M 3M 5M 10M 20 30M Frequency in Hz Correction Detector Frequency Read Margin Factor Level Limit (MHz) Level (dB) (dBμV/m) (dBμV/m) (dBμV) (dB) 0.128 65.0 20.6 85.6 105.4 19.8 PK 0.386 41.9 20.9 62.8 95.9 33.1 PK 0.638 32.6 21.3 53.9 71.5 17.6 PK 0.898 26.5 21.3 47.8 68.5 20.7 PK The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands 9-90 kHz, 110-490 kHz and above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector. Commented [HMI1]: 都是用的 PK？ Remark: 1. Corr. (dB) = Antenna Factor (dB) + Cable Loss (dB) 2. Level (dBμV/m) = Corr. (dB) + Read Level (dBμV) 3. Margin (dB) = Limit (dBμV/m) –Level (dBμV/m) 4. Only record the date closed to limit 5. The emission is worst case on Vertical 6. When Peak emission level was below AV or QP limit, the AV and QP emission level did not be Commented [HMI2]: 去掉？ recorded. Version: 21 August 2017 Page 15 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT 30 MHz~1 GHz Spurious Emissions. Quasi-Peak Measurement Vertical: 100 90 80 70 60 FCC 15 50 dBµV/m Level in 40 30 20 10 0 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz Receiver Correction Emission Frequency Reading factors Limit Level (MHz) Level (dB/m) (dBµV/m) (dBµV/m) (dBµV) 58.92 14.3 10.2 24.5 40.0 109.04 10.6 12.4 23.0 43.5 163.84 13.7 9.4 23.1 43.5 Remark: Final Test Level =Receiver Reading + Correction Factor Correction Factor = Antenna Factor + Cable Loss. Version: 21 August 2017 Page 16 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT Horizontal: 100 90 80 70 60 FCC 15 50 dBµV/m Level in 40 30 20 10 0 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz Receiver Correction Emission Frequency Reading factors Limit Level (MHz) Level (dB/m) (dBµV/m) (dBµV/m) (dBµV) 70.00 8.0 9.9 17.9 40.0 109.28 6.7 12.4 19.1 43.5 192.12 11.7 11.6 23.3 43.5 Remark: Final Test Level =Receiver Reading + Correction Factor Correction Factor = Antenna Factor + Cable Loss. Version: 21 August 2017 Page 17 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT 5.0 Conducted Emission Test Test Configuration: AC power 50Ω terminator source AE TRANSFORMER AMN EUT TEST RECEIVER Passive voltage probe Test Setup and Procedure: Test was performed according to ANSI C63.10 Clause 6.2. The EUT was set to achieve the maximum emission level. The mains terminal disturbance voltage was measured with the EUT in a shielded room. The EUT was connected to AC power source through an Artificial Mains Network which provides a 50Ω linear impedance Artificial hand is used if appropriate (for handheld apparatus). The load/control terminal disturbance voltage was measured with passive voltage probe if appropriate. The table-top EUT was placed on a 0.8m high non-metallic table above earthed ground plane (Ground Reference Plane).And for floor standing EUT, was placed on a 0.1m high non-metallic supported on GRP. The EUT keeps a distance of at least 0.8m from any other of the metallic surface. The Artificial Mains Network is situated at a distance of 0.8m from the EUT. During the test, mains lead of EUT excess 0.8m was folded back and forth parallel to the lead so as to form a horizontal bundle with a length between 0.3m and 0.4m The bandwidth of test receiver was set at 9 kHz. The frequency range from 150 kHz to 30MHz was checked. Version: 21 August 2017 Page 18 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT Test Data and Curve At main terminal: Pass Tested Wire: Live Full Spectrum 100 80 FCC Part 15 B Voltage on Mains QP 60 Level in dBμ FCC Part 15 B Voltage on Mains AV 40 20 0 150k 300 400 500 800 1M 2M 3M 4M 5M 6 8 10M 20M 30M Frequency in Hz Frequency QuasiPeak Average Limit Margin Meas. Bandwidth Line Filter Corr. (MHz) (dB¦ÌV) (dB¦ÌV) (dB¦ÌV) (dB) Time (kHz) (dB) (ms) 0.178000 --- 39.46 54.58 15.12 1000. 9.000 L1 ON 9.7 0.178000 48.55 --- 64.58 16.03 0 1000. 9.000 L1 ON 9.7 0.270000 42.02 --- 61.12 19.10 0 1000. 9.000 L1 ON 9.7 0.354000 --- 35.97 48.87 12.90 0 1000. 9.000 L1 ON 9.7 0.446000 38.36 --- 56.95 18.59 0 1000. 9.000 L1 ON 9.7 0.446000 --- 35.32 46.95 11.63 0 1000. 9.000 L1 ON 9.7 0.806000 --- 33.15 46.00 12.85 0 1000. 9.000 L1 ON 9.7 0.818000 36.46 --- 56.00 19.54 0 1000. 9.000 L1 ON 9.7 1.250000 --- 29.53 46.00 16.47 0 1000. 9.000 L1 ON 9.7 1.730000 33.63 --- 56.00 22.37 0 1000. 9.000 L1 ON 9.7 2.322000 --- 27.42 46.00 18.58 0 1000. 9.000 L1 ON 9.7 3.486000 35.69 --- 56.00 20.31 0 1000. 9.000 L1 ON 9.7 4.070000 34.81 --- 56.00 21.19 0 1000. 9.000 L1 ON 9.7 4.646000 --- 30.98 46.00 15.02 0 1000. 9.000 L1 ON 9.9 8.130000 --- 31.86 50.00 18.14 0 1000. 9.000 L1 ON 9.8 16.878000 --- 19.05 50.00 30.95 0 1000. 9.000 L1 ON 10.0 23.370000 --- 30.81 50.00 19.19 0 1000. 9.000 L1 ON 10.2 0 Remark: 1. Corr. (dB) = LISN Factor (dB) + Cable Loss (dB) 2. Level (dBμV) = Corr. (dB) + Read Level (dBμV) 3. Delta Limit (dB) = Level (dBμV)-Limit (dBμV) Version: 21 August 2017 Page 19 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT Tested Wire: Neutral Full Spectrum 100 80 FCC Part 15 B Voltage on Mains QP 60 Level in dBμ FCC Part 15 B Voltage on Mains AV 40 20 0 150k 300 400 500 800 1M 2M 3M 4M 5M 6 8 10M 20M 30M Frequency in Hz Frequency QuasiPeak Average Limit Margin Meas. Bandwidth Line Filter Corr. (MHz) (dB¦ÌV) (dB¦ÌV) (dB¦ÌV) (dB) Time (kHz) (dB) (ms) 0.178000 --- 41.46 54.58 13.12 1000.0 9.000 N ON 9.7 0.182000 46.20 --- 64.39 18.20 1000.0 9.000 N ON 9.7 0.354000 --- 37.93 48.87 10.94 1000.0 9.000 N ON 9.7 0.358000 40.83 --- 58.78 17.95 1000.0 9.000 N ON 9.7 0.718000 39.72 --- 56.00 16.28 1000.0 9.000 N ON 9.7 0.722000 --- 35.55 46.00 10.45 1000.0 9.000 N ON 9.7 0.970000 36.08 --- 56.00 19.92 1000.0 9.000 N ON 9.7 0.990000 --- 34.50 46.00 11.50 1000.0 9.000 N ON 9.7 1.250000 --- 32.50 46.00 13.50 1000.0 9.000 N ON 9.7 1.330000 36.82 --- 56.00 19.18 1000.0 9.000 N ON 9.7 2.326000 --- 30.09 46.00 15.91 1000.0 9.000 N ON 9.7 3.490000 32.09 --- 56.00 23.91 1000.0 9.000 N ON 9.7 3.606000 --- 17.09 46.00 28.91 1000.0 9.000 N ON 9.7 3.606000 27.83 --- 56.00 28.17 1000.0 9.000 N ON 9.7 16.014000 --- 32.24 50.00 17.76 1000.0 9.000 N ON 10.1 23.514000 --- 30.25 50.00 19.75 1000.0 9.000 N ON 10.3 Remark: 1. Corr. (dB) = LISN Factor (dB) + Cable Loss (dB) 2. Level (dBμV) = Corr. (dB) + Read Level (dBμV) 3. Delta Limit (dB) = Level (dBμV)-Limit (dBμV) Version: 21 August 2017 Page 20 of 21 FCC Part 15C-a

Intertek Report: No: 180424178GZU-001 TEST REPORT 6.0 Test Equipment List Conducted Disturbance-Mains Terminal(1) Cal. Due date Calibration Equipment No. Equipment Model Manufacturer (DD-MM-YYYY) Interval EM080-05 EMI receiver ESCI R&S 24/07/2018 1Y EM006-05 LISN ENV216 R&S 06/06/2019 1Y Digital Temperature-Humidity SA047-112 RS210 YIJIE 03/11/2018 1Y Recorder EM004-04 EMC shield Room 8m×3m×3m Zhongyu 07/01/2019 1Y Radiated Disturbance（9 kHz-30 MHz） Cal. Due date Calibration Equipment No. Equipment Model Manufacturer (DD-MM-YYYY) Interval ETS- EM030-04 3m Semi-Anechoic Chamber 9×6×6 m3 06/05/2019 1Y LINDGREN EM031-02 EMI Test Receiver (9 kHz~7 GHz) R&S ESR7 R&S 03/11/2019 1Y EM011-04 Loop antenna (9 kHz-30 MHz) HFH2-Z2 R&S 14/06/2019 1Y EM031-02-01 Coaxial cable / R&S 06/05/2019 1Y Digital Temperature-Humidity SA047-118 RS210 YIJIE 7/10/2018 1Y Recorder EM045-01-01 EMC32 software (RE/RS) V10.01.00 R&S N/A N/A Radiated Disturbance（30 MHz-1 GHz） Cal. Due date Calibration Equipment No. Equipment Model Manufacturer (DD-MM-YYYY) Interval ETS- EM030-04 3m Semi-Anechoic Chamber 9×6×6 m3 06/05/2019 1Y LINDGREN EM031-02 EMI Test Receiver (9 kHz~7 GHz) R&S ESR7 R&S 03/11/2019 1Y TRILOG Super Broadband test SCHWARZBEC EM033-01 VULB 9163 19/09/2018 1Y Antenna（30 MHz-3 GHz） K EM031-02-01 Coaxial cable / R&S 06/05/2019 1Y EM036-01 Common-mode absorbing clamp CMAD 20B TESEQ 31/07/2018 1Y Digital Temperature-Humidity SA047-118 RS210 YIJIE 10/07/2018 1Y Recorder EM045-01-01 EMC32 software (RE/RS) V10.01.00 R&S N/A N/A ********************************End of the test report****************************** Version: 21 August 2017 Page 21 of 21 FCC Part 15C-a


Document Created: 2018-08-03 09:33:11
Document Modified: 2018-08-03 09:33:11
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC