Part 15B Test Report

FCC ID: 2AFMZ-RK-175

Test Report

Download: PDF
FCCID_3021848

FCC Test Report FCC ID:2AFMZ-RK-175 Product: RK-175 Trade Name: RTK Model Number: RK-175 Serial Model: N/A Report No.: NTEK- 2016NT05035459F4 Prepared for ACCESS TELECOM 1882 NW 97TH AVE, DORAL, MIAMI, FL 33172, UNITED STATES OF AMERICA. Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao’an District, Shenzhen P.R. China Tel.: +86-0755-61156588 Fax.: +86-0755-61156599 Website: www.ntek.org.cn

Page 2 of 23 Report No.: NTEK- 2016NT05035459F4 TEST RESULT CERTIFICATION Applicant’s name ................. : ACCESS TELECOM Address ................................. : 1882 NW 97th Ave, Doral, Miami, Fl 33172, United States of America. Manufacturer's Name .......... : Locopo Technolgy Co.,Ltd. B Rm./Flat 1501(056), 15/F, Spa Centre,53-55 Lockhart Road, Wan Address ................................. : Chai, Kong Kong. Product description Product name ........................... : RK-175 Model and/or type reference : RTK FCC Part15B:01 Oct.2016 Standards ............................. : ANSI C63.4:2014 This device described above has been tested by NTEK, and the test results show that the equipment under test (EUT) is in compliance with Part 15 of FCC Rules. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of NTEK, this document may be altered or revised by NTEK, personnel only, and shall be noted in the revision of the document. Date of Test ............................................ : Date (s) of performance of tests ............. : 03 May. 2016 ~ 24 May. 2016 Date of Issue ........................................... : 24 May. 2016 Test Result ............................................... : Pass Testing Engineer : (Jack Li) Technical Manager : (Jason Chen) Authorized Signatory : (Sam Chen)

Page 3 of 23 Report No.: NTEK- 2016NT05035459F4 Table of Contents Page 1 . TEST SUMMARY 4 1.1 TEST FACILITY 5 1.2 MEASUREMENT UNCERTAINTY 5 2 . GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF EUT 6 2.2 DESCRIPTION OF TEST SETUP 8 2.3 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL 9 2.4 MEASUREMENT INSTRUMENTS LIST 10 3 . EMC EMISSION TEST 11 3.1 CONDUCTED EMISSION MEASUREMENT 11 3.1.1 POWER LINE CONDUCTED EMISSION 11 3.1.2 TEST PROCEDURE 12 3.1.3 TEST SETUP 12 3.1.4 EUT OPERATING CONDITIONS 12 3.1.5 TEST RESULTS 13 3.2 RADIATED EMISSION MEASUREMENT 17 3.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT 17 3.2.2 TEST PROCEDURE 17 3.2.3 TEST SETUP 18 3.2.4 TEST RESULTS 19 3.2.5 TEST RESULTS(1000~12400MHz) 21 4 . EUT TEST PHOTO 22

Page 4 of 23 Report No.: NTEK- 2016NT05035459F4 1. TEST SUMMARY Test procedures according to the technical standards: EMC Emission Standard Test Item Limit Judgment Remark Conducted Emission Class B PASS FCC Part15B:2014 ANSI C63.4: 2014 Radiated Emission Class B PASS NOTE: (1) ’N/A’ denotes test is not applicable in this Test Report (2) For client’s request and manual description, the test will not be executed.

Page 5 of 23 Report No.: NTEK- 2016NT05035459F4 1.1 TEST FACILITY NTEK Testing Technology Co., Ltd Add. : 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao’an District, Shenzhen P.R. China. FCC Registration Number:238937; IC Registration Number:9270A-1 CNAS Registration Number:L5516 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. A. Conducted Measurement : Test Site Method Measurement Frequency Range U,(dB) NOTE NTEKC01 ANSI 150 KHz ~ 30MHz 3.2 B. Radiated Measurement : Test Site Method Measurement Frequency Range U,(dB) NOTE NTEKA01 ANSI 30MHz ~ 1000MHz 4.7 1GHz ~12.4GHz 5.0

Page 6 of 23 Report No.: NTEK- 2016NT05035459F4 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment RK-175 Trade Name RTK Model Name RK-175 Serial Model N/A Model Difference N/A The EUT is a Industrial RK-175. Connecting I/O port: USB, Earphone Operation Frequency: BT:2402~2480 MHz WIFI:802.11b/g/n(20MHz): 2412~2462MHz 802.11n(40MHz):2422~2452MHz GSM: 824.2-848.8MHz/1850.2-1909.8MHz WCDMA: 826.4-846.6MHz/ Product Description 1852.4-1907.6MHz Modulation Type: BT(1Mbps): GFSK BT EDR(2Mbps): π/4-DQPSK BT EDR(3Mbps): 8-DPSK IEEE 802.11b : DSSS (CCK, QPSK, DBPSK) IEEE 802.11g/n (HT20/HT40) : OFDM (64QAM, 16QAM, QPSK, BPSK) GSM / DCS: GMSK WCDMA:QPSK Power Source DC Voltage Model: XHY050200UUCH Adapter Input: 100-240V~, 50/60Hz, 0.5A MAX Output: 5.0V 2A Battery DC 3.7V, 2500mAh

Page 7 of 23 Report No.: NTEK- 2016NT05035459F4 2.1.1 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 Connect to PC Mode 2 Camera Mode 3 TF card Play Mode 4 “H” Pattern For Conducted Test Final Test Mode Description Mode 1 Connect to PC Mode 2 Camera Mode 3 TF card Play Mode 4 “H” Pattern For Radiated Test Final Test Mode Description Mode 1 Connect to PC Mode 2 Camera Mode 3 TF card Play Mode 4 “H” Pattern Note: Final Test Mode: Through Pre-scan, find the mode 1 is the worst case. Only the worst case mode is recorded in the report.

Page 8 of 23 Report No.: NTEK- 2016NT05035459F4 2.2 DESCRIPTION OF TEST SETUP RE AC Source AC Source AC Source C-7 C-6 C-2 C-3 C-8 C-1 E-2 E-3 E-1 E-4 Printer PC EUT Monitor 0.8m C-4 C-5 E-5 E-6 KB Mouse Table 1.5m CE AC Source C-3 C-2 C-7 AC Source C-1 C-8 E-2 E-4 E-1 E-3 C-6 Printer Monitor EUT PC LISN 0.8m C-4 C-5 E-5 E-6 KB Mouse Table 1.5m

Page 9 of 23 Report No.: NTEK- 2016NT05035459F4 2.3 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Brand Model/Type No. Series No. Note RLTP5567-BLACK ,RLTP556 7-CHAMPAGNE, E-1 RK-175 N/A RK-175 RLTP5567-WHITE, EUT T4016,T5016,T4515,T5015,T 4010,T5010,T5012,T6010 E-2 Printer Canon L11121E LBP2900 E-3 Personal computer DELL FT4Y23X 34413561645 cn-0y6mhx-74261-11f-67e E-4 Monitor DELL IN2020MB s E-5 Keyboard DELL SK-8185 OY526KUS E-6 Mouse DELL MS111-P cn-011d3v-71581-11e-1th7 Item Cable Type Shielded Type Ferrite Core Length Note C-1 USB Cable unshielded NO 1.2m C-2 VGA unshielded NO 1.0m C-3 USB Cable unshielded NO 1.2m C-4 USB Cable unshielded NO 1.0m C-5 USB Cable unshielded NO 1.0m C-6 Power Line unshielded NO 1.2m C-7 Power Line unshielded NO 1.2m C-8 Power Line unshielded NO 1.2m Note: (1) The support equipment was authorized by Declaration of Confirmation. (2) For detachable type I/O cable should be specified the length in cm in『Length』column. (3) “YES” means “shielded” “with core”; “NO” means “unshielded” “without core”.

Page 10 of 23 Report No.: NTEK- 2016NT05035459F4 2.4 MEASUREMENT INSTRUMENTS LIST Radiation Test equipment Item Kind of Manufacturer Type No. Serial No. Last Calibrated Calibratio Equipment calibration until n period 1 Spectrum MY4510804 Agilent E4407B 2015.07.06 2016.07.05 1 year Analyzer 0 2 Test Receiver R&S ESPI 101318 2015.06.07 2016.06.06 1 year 3 Bilog Antenna TESEQ CBL6111D 31216 2015.07.06 2016.07.05 1 year 50Ω Coaxial 620026441 4 Anritsu MP59B 2015.06.07 2016.06.06 1 year Switch 6 Spectrum 5 ADVANTEST R3132 150900201 2015.06.07 2016.06.06 1 year Analyzer EM-AH-101 6 Horn Antenna EM 2011071402 2015.07.06 2016.07.05 1 year 80 7 Horn Ant Schwarzbeck BBHA 9170 9170-181 2015.07.06 2016.07.05 1 year 8 Amplifier EM EM-30180 060538 2015.07.06 2016.07.05 1 year 9 Loop Antenna ARA PLA-1030/B 1029 2015.06.08 2016.06.07 1 year 10 Power Meter R&S NRVS 100696 2015.07.06 2016.07.05 1 year Power 0395.1619. 11 R&S URV5-Z4 2015.07.06 2016.07.05 1 year Sensor 05 12 Test Cable N/A R-01 N/A 2015.07.06 2016.07.05 1 year 13 Test Cable N/A R-02 N/A 2015.07.06 2016.07.05 1 year Conduction Test equipment Item Kind of Manufactu Type No. Serial No. Last Calibrated Calibratio Equipment rer calibration until n period 1 Test Receiver R&S ESCI 101160 2015.06.06 2016.06.05 1 year 2 LISN R&S ENV216 101313 2015.08.24 2016.08.23 1 year 3 LISN EMCO 3816/2 00042990 2015.08.24 2016.08.23 1 year 50Ω Coaxial 620026441 4 Anritsu MP59B 2015.06.07 2016.06.06 1 year Switch 7 5 Passive Voltage R&S ESH2-Z3 100196 2015.06.07 2016.06.06 1 year Probe 6 Absorbing clamp R&S MOS-21 100423 2015.06.08 2016.06.07 1 year 7 Test Cable N/A C01 N/A 2015.06.08 2016.06.07 1 year 8 Test Cable N/A C02 N/A 2015.06.08 2016.06.07 1 year 9 Test Cable N/A C03 N/A 2015.06.08 2016.06.07 1 year

Page 11 of 23 Report No.: NTEK- 2016NT05035459F4 3. EMC EMISSION TEST 3.1 CONDUCTED EMISSION MEASUREMENT 3.1.1 POWER LINE CONDUCTED EMISSION (Frequency Range 150KHz-30MHz) Class A (dBuV) Class B (dBuV) FREQUENCY (MHz) Quasi-peak Average Quasi-peak Average 0.15 -0.5 79.00 66.00 66 - 56 * 56 - 46 * 0.50 -5.0 73.00 60.00 56.00 46.00 5.0 -30.0 73.00 60.00 60.00 50.00 Note: (1) The tighter limit applies at the band edges. (2) The limit of " * " marked band means the limitation decreases linearly with the logarithm of the frequency in the range. The following table is the setting of the receiver Receiver Parameters Setting Attenuation 10 dB Start Frequency 0.15 MHz Stop Frequency 30 MHz IF Bandwidth 9 kHz

Page 12 of 23 Report No.: NTEK- 2016NT05035459F4 3.1.2 TEST PROCEDURE a. The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d. LISN at least 80 cm from nearest part of EUT chassis. e. For the actual test configuration, please refer to the related Item –EUT Test Photos. 3.1.3 TEST SETUP 3.1.4 EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 2.3 Unless otherwise a special operating condition is specified in the follows during the testing.

Page e 13 of 23 Rep port No.: NTEK- 2016NT T05035459F4 4 3.1.5 TE EST RESUL LTS EUT: RK-175 R Moodel Name. : RK-1 175 Temperaature: 2 ℃ 26 Re elative Humidity: 54% % Pressuree: 1010hPa Tes st Date: 2016 6-5-11 Test Modde: M Mode 1 Ph hase : L Test Volttage: D 5V From DC m PC AC 12 20V/60Hz Frequency Reading Level Correct Factor Measure-ment Limiits M Margin Remark (MHzz) (d dBμV) (dB) (dBμV) (dBμ μV) (dB) 0.202 20 3 31.27 10.28 41.55 63.5 52 --21.97 QP 0.502 20 2 29.22 10.02 39.24 56.0 00 --16.76 AVG 1.102 20 2 25.12 10.00 35.12 56.0 00 --20.88 QP 7.077 79 3 35.23 9.88 45.11 60.0 00 --14.89 AVG 25.066 60 3 33.41 10.18 43.59 60.0 00 --16.41 QP 16.141 19 3 31.85 10.02 41.87 60.0 00 --18.13 AVG 0.198 80 2 28.03 10.28 38.31 53.6 69 --15.38 QP 0.402 20 2 23.52 10.24 33.76 47.8 81 --14.05 AVG 24.962 20 2 27.97 10.18 38.15 50.0 00 --11.85 QP 16.237 79 2 24.72 10.02 34.74 50.0 00 --15.26 AVG Remark: 1. All readings are Quassi-Peak and Avverage valuess. 2. Factor = Insertion Losss + Cable Loss.

Page e 14 of 23 Rep port No.: NTEK- 2016NT T05035459F4 4 EUT: RK-175 R Moodel Name. : RK-1 175 Temperaature: 2 ℃ 26 Re elative Humidity: 54% % Pressuree: 1010hPa Tes st Date: 2016 6-5-11 Test Modde: M Mode 1 Ph hase : N Test Volttage: D 5V From DC m PC AC 12 20V/60Hz Frequency Reading Level Correct Factor Measure-ment Limiits M Margin Remark (MHzz) (d dBμV) (dB) (dBμV) (dBμ μV) (dB) 0.202 20 3 33.82 10.17 43.99 63.5 52 --19.53 QP 0.802 20 2 26.60 10.03 36.63 56.0 00 --19.37 AVG 1.506 60 2 24.96 9.94 34.90 56.0 00 --21.10 QP 7.2419 3 37.20 9.85 47.05 60.0 00 --12.95 AVG 25.166 60 3 33.91 10.17 44.08 60.0 00 --15.92 QP 0.202 20 2 29.55 10.17 39.72 53.5 52 --13.80 AVG 0.802 20 2 24.53 10.03 34.56 46.0 00 --11.44 QP 25.166 60 2 27.92 10.17 38.09 50.0 00 --11.91 AVG Remark: 1. All readings are Quassi-Peak and Avverage valuess. 2. Factor = Insertion Losss + Cable Loss.

Page e 15 of 23 Rep port No.: NTEK- 2016NT T05035459F4 4 EUT: RK-175 R Moodel Name. : RK-1 175 Temperaature: 2 ℃ 26 Re elative Humidity: 54% % Pressuree: 1010hPa Tes st Date: 2016 6-5-11 Test Modde: M Mode 1 Ph hase : L Test Volttage: D 5V From DC m PC AC 24 40V/60Hz Frequency Reading Level Correct Factor Measure-ment Limiits M Margin Remark (MHzz) (d dBμV) (dB) (dBμV) (dBμ μV) (dB) 0.202 20 2 25.87 10.28 36.15 63.5 52 --27.37 QP 0.502 20 2 29.43 10.02 39.45 56.0 00 --16.55 AVG 7.373 39 3 38.14 9.88 48.02 60.0 00 --11.98 QP 16.061 19 3 31.48 10.02 41.50 60.0 00 --18.50 AVG 25.190 00 3 34.24 10.18 44.42 60.0 00 --15.58 QP 1.406 60 2 25.46 9.94 35.40 56.0 00 --20.60 AVG 0.502 20 2 24.26 10.02 34.28 46.0 00 --11.72 QP 1.406 60 2 23.75 9.94 33.69 46.0 00 --12.31 AVG 15.857 79 2 23.67 10.01 33.68 50.0 00 --16.32 QP 25.390 00 2 27.45 10.18 37.63 50.0 00 --12.37 AVG Remark: 1. All readings are Quassi-Peak and Avverage valuess. 2. Factor = Insertion Losss + Cable Loss.

Page e 16 of 23 Rep port No.: NTEK- 2016NT T05035459F4 4 EUT: RK-175 R Moodel Name. : RK-1 175 Temperaature: 2 ℃ 26 Re elative Humidity: 54% % Pressuree: 1010hPa Tes st Date: 2016 6-5-11 Test Modde: M Mode 1 Ph hase : N Test Volttage: D 5V From DC m PC AC 24 40V/60Hz Frequency Reading Level Correct Factor Measure-ment Limiits M Margin Remark (MHzz) (d dBμV) (dB) (dBμV) (dBμ μV) (dB) 0.202 20 3 33.50 10.17 43.67 63.5 52 --19.85 QP 0.502 20 2 27.34 10.04 37.38 56.0 00 --18.62 AVG 1.102 20 2 25.41 10.02 35.43 56.0 00 --20.57 QP 7.265 59 3 36.48 9.85 46.33 60.0 00 --13.67 AVG 25.174 40 3 34.58 10.17 44.75 60.0 00 --15.25 QP 9.393 39 3 36.31 9.88 46.19 60.0 00 --13.81 AVG 0.202 20 3 30.66 10.17 40.83 53.5 52 --12.69 QP 0.802 20 2 23.42 10.03 33.45 46.0 00 --12.55 AVG 25.174 40 2 27.32 10.17 37.49 50.0 00 --12.51 QP Remark: 1. All readings are Quassi-Peak and Avverage valuess. 2. Factor = Insertion Losss + Cable Loss.

Page 17 of 23 Report No.: NTEK- 2016NT05035459F4 3.2 RADIATED EMISSION MEASUREMENT 3.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT Class A (at 10m) Class B (at 3m) FREQUENCY (MHz) dBuV/m dBuV/m 30 ~ 88 39.0 40.0 88 ~ 216 43.5 43.5 216 ~ 960 46.5 46.0 Above 960 49.5 54.0 Notes: (1) The limit for radiated test was performed according to as following: FCC PART 15B /ICES-003. (2) The tighter limit applies at the band edges. (3) Emission level (dBuV/m)=20log Emission level (uV/m). 3.2.2 TEST PROCEDURE Test Arrangement for Radiated Emissions up to 1 GHz a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at an accredited test facility. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. Note: The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for quasi-peak detection (QP) at frequency below 1GHz. Test Arrangement for Radiated Emissions above 1 GHz. a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at an accredited chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna can be varied from one meter to four meters, the height of adjustment depends on the EUT height and the antenna 3dB beamwidth both, to detect the maximum value of the field strength.Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. Note：For the hand-held device, the EUT should be measured for all 3 axes and only the worst case is recorded in the report

Page 18 of 23 Report No.: NTEK- 2016NT05035459F4 During the radiated emission test, the Spectrum Analyzer was set with the following configurations: Frequency Band Function Resolution bandwidth Video Bandwidth (MHz) 30 to 1000 QP 120 kHz 300 kHz Peak 1 MHz 1 MHz Above 1000 Avg 1 MHz 10 Hz 3.2.3 TEST SETUP For Radiated Emission 30~1000MHz (B) Radiated Emission Test Set-Up Frequency Above 1GHz

Page e 19 of 23 Rep port No.: NTEK- 2016NT T05035459F4 4 3.2.4 TE EST RESUL LTS TEST RES SULTS (30~ ~1000 MHz)) EUT: R RK-175 Moodel Name. : RK-1175 Temperaature: 2 ℃ 24 Re elative Humidity: 54% % Pressure e: 1010 hPa Tes st Date : 2016 6-5-11 Test Mod de : M Mode 1 Po olarization : Horizzontal Test Pow wer : D 5V From DC m PC AC 12 20V/60Hz Meter Em mission Frequenc cy Fac ctor Limits Margin Polar Read ding Level L (H/V) Remark (MHz) (dBuV) (d dB) (dB BuV/m) (dBuV/m) (dB) H 228.490 04 19.61 10 0.85 30.46 3 46.00 -15.54 QP H 163.1818 15.34 11.63 26.97 2 43.50 -16.53 QP H 133.618 88 13.45 10 0.95 24.40 2 43.50 -19.10 QP Remark: Factor = Antenna A Fa actor + Cable Loss - Am mplifier.

Page e 20 of 23 Rep port No.: NTEK- 2016NT T05035459F4 4 EUT: RK-175 R Moodel Name. : RK-1175 Temperaature: 2 ℃ 24 Re elative Humidity: 54% % Pressure e: 1010 hPa Tes st Date : 20166-5-11 Test Mod de : M Mode 1 Po olarization : Vertiical Test Pow wer : D 5V From DC m PC AC 12 20V/60Hz Me eter Em mission Frequency Factor Limits Margin Polar Read ding Level L (H/V) Remark (MHz) (dB BuV) (d dB) (dB BuV/m) (dBuV/m) (dB) V 127.21776 27.26 10 0.76 38.02 3 43.50 -5.48 QP V 204.95550 19.73 11 1.57 31.30 3 43.50 -12.20 QP V 332.51887 16.36 13 3.72 30.08 3 46.00 -15.92 QP V 42.74966 15.99 13 3.16 29.15 2 40.00 -10.85 QP V 665.80334 20.69 20 0.77 41.46 4 46.00 -4.54 QP Remark:: Factor = Antenna Factor + Cab ble Loss - Amplifier. A

Page 21 of 23 Report No.: NTEK- 2016NT05035459F4 3.2.5 TEST RESULTS(1000~12400MHz) All the modulation modes have been tested, and the worst result was report as below: Meter Emission Frequency Factor Limits Margin Polar Reading Level Remark (H/V) (MHz) (dBuV) (dB) (dBuV/m) (dBuV/m) (dB) V 4823.05 48.80 1.34 50.14 74.00 -23.86 peak V 4823.05 50.47 -12.49 37.98 54.00 -16.02 AVG V 2347.56 51.09 -10.84 40.25 74.00 -33.75 peak V 2347.56 50.48 -4.88 45.60 54.00 -8.40 AVG H 4866.45 47.90 1.52 49.42 74.00 -24.58 peak H 4866.45 51.19 -4.66 46.53 54.00 -7.47 AVG H 4433.62 49.71 -0.56 49.15 74.00 -24.85 peak H 4433.62 50.38 -12.69 37.69 54.00 -16.31 AVG Remark: 1. Absolute Level= ReadingLevel+ Factor, Margin= Absolute Level – Limit All other emissions more than 20dB below the limit.

Page 22 of 23 Report No.: NTEK- 2016NT05035459F4 4. EUT TEST PHOTO Radiated Measurement Photos

Page 23 of 23 Report No.: NTEK- 2016NT05035459F4 Conducted Measurement Photos


Document Created: 2016-06-07 15:53:29
Document Modified: 2016-06-07 15:53:29
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC