Test Report

FCC ID: 2AFKNF316W

Test Report

Download: PDF
FCCID_4459276

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch o2 0197 oo f,/’/,‘:\\"\‘\? AccrREDITED) *Aw ceat #asie01 Report No.: SZEM190801754401 Page: 1 of 29 TEST REPORT Application No.: SZEM1908017544CR Applicant: Spigen Korea Co., Ltd. Address of Applicant: Spigen HQ—A, 446, Bongeunsa—ro, Gangnam—gu, Seoul, 06153, South Korea Manufacturer: Spigen Korea Co., Ltd. Address of Manufacturer: 446, Bongeunsa—ro, Gangnam—gu, Seoul, 06153, South Korea. Factory: ShenZhen Fangxin Technology Co., Ltd. Address of Factory: Rm 503, 5F, Hengbo Innovation Science and Technology Park, No.33, Qingning Rd, Longhua St, Longhua Dist, Shenzhen, China Equipment Under Test (EUT): EUT Name: Flex Wireless Charger Model No.: F316GW Trade mark: Spigen, Steadiboost FCC ID: 2AFKNF316W Standard(s) : 47 CFR Part 15, Subpart C Date of Receipt: 2019—08—15 Date of Test: 2019—08—17 to 2019—08—20 Date of Issue: 2019—08—26 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. leal0 Keny Xu EMC Laboratory Manager Unless otherwise agreed in writing, this document is issued by the Company subject to its General Conditions of Service printed overieaf, available on request or accessible at hitp:‘/www.sus.com/en/Terms—and—Gonditions.aspx and, for electronic format documents, subject io Terms and Conditions for Electronic Documents at hitp:/Fww.sgs.comfen/Terms—and—Conditlons/Terms—©—Document. aspx Attention is drawn to the limitation of labilty, indamnification and Juriediction issues deined tharein. Any holder of this documentis advised that information contained hereonreflects the Company‘s findings at the time of ts intervention only and within the limits of Clients instructions, if any. The Company‘s sole responsibility is to it Client and this document does not exonerate parties to a transaction from exereising all their rights and obligations underthe transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this documentis unlawiul and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. Attention: To check the authenticity of testing /inspection report & certificate, please contact us at talephane: (86—755) 8307 1443, or email: CN.Doecheck@sgs.com Co,Lid No.t WortshopN—10,l Secton, Science 8 TechnologyPar,Shnzhen, Chine $18057 t (86—755)20012053 1 (%6—759) 26710504 wnw:sgegroup.com.en abodlory #B —RHI— ARRIHEN—10H—S1B AB4: 51g057 t (B6—758)26012053 1 (86—755)26710504 sgochina@sgs.com T Member of the SGS Group (SGS SA)

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 2 of 29 Revision Record Version Chapter Date Modifier Remark 01 2019-08-26 Original Authorized for issue by: Damon Su /Project Engineer Eric Fu /Reviewer

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 3 of 29 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result 47 CFR Part 15, 47 CFR Part 15, Subpart Antenna Requirement N/A Pass Subpart C C 15.203 Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Emissions 47 CFR Part 15, ANSI C63.10 (2013) 47 CFR Part 15, Subpart at AC Power Line Pass Subpart C Section 6.2 C 15.207 (150kHz-30MHz) 47 CFR Part 15, ANSI C63.10 (2013) 47 CFR Part 15, Subpart 20dB Bandwidth Pass Subpart C Section 6.9.2 C 15.215 47 CFR Part 15, ANSI C63.10 (2013) 47 CFR Part 15, Subpart Restricted Bands Pass Subpart C Section 6.10.5 C 15.205 Radiated Emissions 47 CFR Part 15, ANSI C63.10 (2013) 47 CFR Part 15, Subpart Pass (9kHz-30MHz) Subpart C Section 6.4 C 15.205 & 15.209 Radiated Emissions 47 CFR Part 15, ANSI C63.10 (2013) 47 CFR Part 15, Subpart Pass (30MHz-1GHz) Subpart C Section 6.5 C 15.205 & 15.209

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 4 of 29 3 Contents Page COVER PAGE ... . ... ccnnnnennennenneeeeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneenennennennenee 1 TEST SUMMARY ..... ... .e n0e 00e en rerrerernerneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeennennenneea 3 es n 4 GENERAL INFORMATION ... ... ... 00e n0000nmerrerrerrerreereereereeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneenennennenee 5 4.1 DETAILS OF E.ULT. .cc & o o o 1 n 4.2 DescRrirtion or Support Units.. 4.3 MEASUREMENT UNCERTAINTY . 4.4 TEST LOCATION .scccccceeee. 4.5 TEST FAGILITY «.cc 4.6 DEeviaTION FRoM STANDARDS . 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ... ... ... cce en en en en en en en en en eereereereereereereereeneeneeneeneee. EQUIPMENT LIST ... .000 00000eeeeeeeeeeeeeeeneenerneenerneeneenerneenernernernernernernernennennennennennennennennennennennennnnnnnnnnnn 7 RADIO SPECTRUM TECHNICAL REQUIREMENT ........0.00000 0000 eeeeeeeeeeeeeenenernernernernernernernennnnnnnnn 9 6.1 ANTENNA REQUIREMENT . ... ... .200 en ee e e en en en eereereereereereereereereereereereereereereereereereereereereeneeneeneeneeneee 9 6.1.1 Test Requirement: 6.1.2 Conclusion......... RADIO SPECTRUM MATTER TEST RESULTS .......0.00 0006 eeeeeeeeeeenenerneeneenernerneeneeneenernennennennnnnnee 10 7.1 ConpuctEp Emissions at AC Powenr LinE (150KHz—30MHz) «.c 40 7.1.1 E.U.T. OD&@FANOM...........cccceeereermermernernernernernerererrerrenes .11 7.1.2 Test Setup Diagram ... 2411 7.1.3 Measurement Procedure and Data 12 7.2 200B BANDWIDTH ..... A5 7,2.1 E.U.T. Operation... 15 7.2.2 Test Setup Diagram. 15 7.2.3 Measurement Procedure and Data 15 7.3 RestRICTED BANDsS ... A7 7.8.1 E.U.T. Operation... 17 7.3.2 Test Setup Diagram. 17 7.3.3 Measurement Procedure and Data 2. 47 7.4 RaDiaTED EMissiONs (9KHz—30MHz) ... «...19 7.4.1 E.U.T. Operation...... ...20 7.4.2 Test Setup Diagram. ...20 7.4.3 Measurement Procedure and Data ... 20 7.5 RapiatED Emissions (3OMHz—1GHz) ... ....23 7.5.1 E.U.T. Operation...... .... 24 7.5.2 Test Setup Diagram. .... 24 7.5.3 MBEASU@M@NT PYOCB@UU® @MU DBIA.................cccceereereermermermermermermermermernererererererervenvens 25 PHOTOGRAPHS ..... ... ... ccnnmeeneenneeeeneereereereereereereereereereereereereereereereereerrerreneeeeneeeeneeneene en en nnnnnn en en n 29 8.1 TEST SETUP ... .20 en en ee en en en en en en en en en eeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneeneen en 29 8.2 EUT CONSTRUCTIONAL DETAILS (EUT PHOTOS) 1..2.. ... 0. 00ee0eeeeeeeeeeeeeeeeeeeeeneerevreeneenevnevnevnevnevnevnennevne 29 Unless otherwise agreed in writing, this document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at hitp/waw.sas..comen/Terms—and—Conditions.aspx and, for electronic format documents, Subject to Terms and Gonditions for Electronte Documents at hliplwim sgs. comfenTerms—ang:Condiionsyterms—e—Dpoument.aspr: Attention is drawn to the limitation of lability, indamnification and jurlediction issues defined tharein. Any holder of this document is advised that information contained hereon raflects the Company‘s findings at the time of ts intervention only and within the !imits of Clients instructions, if any. The Company‘s sole responsibiity is to its Client and this document does not exonerate parties to a transaction from exereising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this documentis unlawful and offendars may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample() tested and such sample(s) are retained for 30 days only. Aftention: To check the authenticity of testing /inspection report & certificate, please contact us at talephone: (86—755) 8307 1443, or email: CN.Doecheck@sgs.com 3. [No—t Woristep,N—1, Middl Secion,Scence & Technology Prt Shenthen, China 518057 t (86—756)26012053 1 (%6—750)26710504 wincsggroup.comon #B 0+ RRRIHEN—10H—S1B #B4§: 518057 t (€6—750)20012058 1 (@6—755) 26710504 sgo.china@sgs.com Member of the SGS Group (SGS SA)

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 5 of 29 4 General Information 4.1 Details of E.U.T. Power supply: Input: DC5V, 3A or 9V, 2A or 12V, 1.5A, Output: 5W/7.5W/10W/15W Adapter Model: TY0U01QC Input: AC 100-240V, 50/60Hz 0.8A Output: DC (3.6V-6.5V), 3A or (6.5V-9V), 2A or (9V-12V), 1.5A Cable: USB Cable(Unshielded, 120cm) Operation Frequency: 113.30kHz to 137.66kHz Modulation Type: Load Modulation Antenna Type: Loop Antenna Remark: This device has been tested the worst status of intermediate load and horizontal placement, vertical placement had been tested and only the worst vertical placement had been recorded in the report. The device has been tested with mobile phone at zero charge, intermediate charge, and full charge. 4.2 Description of Support Units Description Manufacturer Model No. Serial No. Smart charger Toye TY0U01QC N/A iPhone 8 Apple A1863 F4GVQ656JC6D Mobile Phone SAMSUNG SM-G9500 R28J9140LPB 4.3 Measurement Uncertainty No. Item Measurement Uncertainty 1 Radio Frequency ± 7.25 x 10-8 2 Conduction Emission ± 3.0dB (150kHz to 30MHz) 3 Occupied Bandwidth ± 3% ± 4.5dB (Below 1GHz) 4 Radiated Spurious emission test ± 4.8dB (Above 1GHz) 5 Temperature test ± 1°C 6 Humidity test ± 3% 7 Supply voltages ± 1.5% 8 Time ± 3%

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 6 of 29 4.4 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Shenzhen, Guangdong, China. 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. 4.5 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 3m Fully-anechoic chamber for above 1GHz, 10m Semi-anechoic chamber for below 1GHz, Shielded Room for Mains Port Conducted Interference Measurement and Telecommunication Port Conducted Interference Measurement of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-20026, R-14188, C-12383 and T-11153 respectively. • FCC –Designation Number: CN1178 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: 406779. • Innovation, Science and Economic Development Canada SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized by ISED as an accredited testing laboratory. CAB identifier: CN0006. IC#: 4620C. 4.6 Deviation from Standards None 4.7 Abnormalities from Standard Conditions None

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 7 of 29 5 Equipment List Radiated Emissions (9kHz-30MHz) Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date 10m Semi-Anechoic SAEMC FSAC1018 SEM001-03 2018-03-31 2021-03-30 Chamber e3 V8.2014-6- Measurement Software AUDIX N/A N/A N/A 27 Coaxial Cable SGS N/A SEM029-01 2019-07-11 2020-07-10 EMI Test Receiver Rohde & Schwarz ESR SEM004-03 2019-04-01 2020-03-31 (9kHz-7GHz) BiConiLog Antenna ETS-LINDGREN 3142C SEM003-02 2019-05-24 2022-05-23 (26-3000MHz) Sonoma Instrument Pre-amplifier 310N SEM005-04 2019-04-12 2020-04-11 Co Active Loop Antenna ETS-Lindgren 6502 SEM003-08 2017-08-22 2020-08-21 20dB Bandwidth Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date DC Power Supply ZhaoXin RXN-305D SEM011-02 2018-09-25 2019-09-24 Spectrum Analyzer Rohde & Schwarz FSP SEM004-06 2018-09-27 2019-09-26 JS1120-2 Measurement Software JS Tonscend N/A N/A N/A BT/WIFI V2. Coaxial Cable SGS N/A SEM031-02 2018-07-12 2019-07-11 Attenuator Weinschel Associates WA41 SEM021-09 N/A N/A Signal Generator KEYSIGHT N5173B SEM006-05 2018-09-27 2019-09-26 Power Meter Rohde & Schwarz NRVS SEM014-02 2018-09-25 2019-09-24 Restricted Bands Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date DC Power Supply ZhaoXin RXN-305D SEM011-02 2018-09-25 2019-09-24 Spectrum Analyzer Rohde & Schwarz FSP SEM004-06 2018-09-27 2019-09-26 JS1120-2 Measurement Software JS Tonscend N/A N/A N/A BT/WIFI V2. Coaxial Cable SGS N/A SEM031-02 2018-07-12 2019-07-11 Attenuator Weinschel Associates WA41 SEM021-09 N/A N/A Signal Generator KEYSIGHT N5173B SEM006-05 2018-09-27 2019-09-26 Power Meter Rohde & Schwarz NRVS SEM014-02 2018-09-25 2019-09-24

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 8 of 29 Radiated Emissions Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date 10m Semi-Anechoic SAEMC FSAC1018 SEM001-03 2018-03-31 2021-03-30 Chamber e3 V8.2014-6- Measurement Software AUDIX N/A N/A N/A 27 Coaxial Cable SGS N/A SEM029-01 2019-07-11 2020-07-10 EMI Test Receiver Rohde & Schwarz ESR SEM004-03 2019-04-01 2020-03-31 (9kHz-7GHz) BiConiLog Antenna ETS-LINDGREN 3142C SEM003-02 2019-05-24 2022-05-23 (26-3000MHz) Sonoma Instrument Pre-amplifier 310N SEM005-04 2019-04-12 2020-04-11 Co Active Loop Antenna ETS-Lindgren 6502 SEM003-08 2017-08-22 2020-08-21 General used equipment Equipment Manufacturer Model No Inventory No Cal Date Cal Due Date Shanghai Humidity/ Temperature Meteorological ZJ1-2B SEM002-03 2018-09-27 2019-09-26 Indicator Industry Factory Shanghai Humidity/ Temperature Meteorological ZJ1-2B SEM002-04 2018-09-27 2019-09-26 Indicator Industry Factory Humidity/ Temperature Mingle N/A SEM002-08 2018-09-27 2019-09-26 Indicator Changchun Barometer Meteorological DYM3 SEM002-01 2019-04-04 2020-04-03 Industry Factory

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 9 of 29 6 Radio Spectrum Technical Requirement 6.1 Antenna Requirement 6.1.1 Test Requirement: 47 CFR Part 15, Subpart C 15.203 6.1.2 Conclusion Standard Requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit permanently attached antenna or of an so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. EUT Antenna: The antenna is integrated on the main PCB and no consideration of replacement. The best case gain of the antenna is 0dBi. Antenna location: Refer to Internal photos.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 10 of 29 7 Radio Spectrum Matter Test Results 7.1 Conducted Emissions at AC Power Line (150kHz-30MHz) Test Requirement 47 CFR Part 15, Subpart C 15.207 Test Method: ANSI C63.10 (2013) Section 6.2 Limit: Frequency of Conducted limit(dBμV) emission(MHz) Quasi-peak Average 0.15-0.5 66 to 56* 56 to 46* 0.5-5 56 46 5-30 60 50 *Decreases with the logarithm of the frequency.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 11 of 29 7.1.1 E.U.T. Operation Operating Environment: Temperature: 23 °C Humidity: 55 % RH Atmospheric Pressure: 1000 mbar Pretest these a:Charge mode_Keep the EUT charging(5W ). modes to find b:Charge mode_Keep the EUT charging(7.5W). the worst case: c:Charge mode_Keep the EUT charging(10W). d:Charge mode_Keep the EUT charging(15W). The worst case c:Charge mode_Keep the EUT charging(10W) for final test: 7.1.2 Test Setup Diagram

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 12 of 29 7.1.3 Measurement Procedure and Data 1) The mains terminal disturbance voltage test was conducted in a shielded room. 2) The EUT was connected to AC power source through a LISN 1 (Line Impedance Stabilization Network) which provides a 50ohm/50μH + 5ohm linear impedance. The power cables of all other units of the EUT were connected to a second LISN 2, which was bonded to the ground reference plane in the same way as the LISN 1 for the unit being measured. A multiple socket outlet strip was used to connect multiple power cables to a single LISN provided the rating of the LISN was not exceeded. 3) The tabletop EUT was placed upon a non-metallic table 0.8m above the ground reference plane. And for floor-standing arrangement, the EUT was placed on the horizontal ground reference plane, 4) The test was performed with a vertical ground reference plane. The rear of the EUT shall be 0.4 m from the vertical ground reference plane. The vertical ground reference plane was bonded to the horizontal ground reference plane. The LISN 1 was placed 0.8 m from the boundary of the unit under test and bonded to a ground reference plane for LISNs mounted on top of the ground reference plane. This distance was between the closest points of the LISN 1 and the EUT. All other units of the EUT and associated equipment was at least 0.8 m from the LISN 2. 5) In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ANSI C63.10 on conducted measurement. Remark: LISN=Read Level+ Cable Loss+ LISN Factor

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 13 of 29 Mode:c; Line:Live Line

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 14 of 29 Mode:c; Line:Neutral Line

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 15 of 29 7.2 20dB Bandwidth Test Requirement 47 CFR Part 15, Subpart C 15.215 Test Method: ANSI C63.10 (2013) Section 6.9.2 Limit: 7.2.1 E.U.T. Operation Operating Environment: Temperature: 23 °C Humidity: 55 % RH Atmospheric Pressure: 1000 mbar Pretest these a:Charge mode_Keep the EUT charging(5W ). modes to find b:Charge mode_Keep the EUT charging(7.5W). the worst case: c:Charge mode_Keep the EUT charging(10W). d:Charge mode_Keep the EUT charging(15W). The worst case c:Charge mode_Keep the EUT charging(10W). for final test: 7.2.2 Test Setup Diagram 7.2.3 Measurement Procedure and Data Test Frequency(KHz) 20dB bandwidth (Hz) Limit (Hz) Results 114.000 26.122 N/A Pass

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 16 of 29 * RBW 10 Hz Marker 1 [T1 ] * VBW 30 Hz -48.78 dBm Ref -20 dBm * Att 10 dB SWT 1 s 113.999839744 kHz -20 ndB [T1] 20.00 dB BW 26.121794872 Hz Temp 1 [T1 ndB] A -30 -69.01 dBm 1 PK 113.986858974 kHz VIEW -40 Temp 2 [T1 ndB] -68.76 dBm 1 114.012980769 kHz -50 -60 T1 T2 -70 3DB -80 -90 -100 -110 -120 Center 113.9998397 kHz 10 Hz/ Span 100 Hz

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 17 of 29 7.3 Restricted Bands Test Requirement 47 CFR Part 15, Subpart C 15.205 Test Method: ANSI C63.10 (2013) Section 6.10.5 Limit: The fundamental wave can not fall in the restricted band 90KHz-110KHz 7.3.1 E.U.T. Operation Operating Environment: Temperature: 23 °C Humidity: 55 % RH Atmospheric Pressure: 1000 mbar Pretest these a:Charge mode_Keep the EUT charging(5W ). modes to find b:Charge mode_Keep the EUT charging(7.5W). the worst case: c:Charge mode_Keep the EUT charging(10W). d:Charge mode_Keep the EUT charging(15W). The worst case c:Charge mode_Keep the EUT charging(10W). for final test: 7.3.2 Test Setup Diagram 7.3.3 Measurement Procedure and Data

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 18 of 29 * RBW 1 kHz Marker 1 [T1 ] VBW 3 kHz -47.80 dBm Ref -20 dBm * Att 10 dB SWT 100 ms 133.012820513 kHz -20 OBW 24.358974359 kHz Temp 1 [T1 OBW] -51.53 dBm A -30 113.301282051 kHz 1 PK Temp 2 [T1 OBW] VIEW -40 -51.60 dBm 137.660256410 kHz 1 T1 T2 -50 -60 -70 3DB -80 -90 -100 -110 -120 Start 100 kHz 10 kHz/ Stop 200 kHz According the test data of Radiated Emission(9-150KHz) in clause 7.4, the fundamental wave is not fall in the restricted band 90KHz-110KHz, the field strength also meet the 15.209 requirement, so this test is Pass.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 19 of 29 7.4 Radiated Emissions (9kHz-30MHz) Test Requirement 47 CFR Part 15, Subpart C 15.205 & 15.209 Test Method: ANSI C63.10 (2013) Section 6.4 Measurement Distance: 3m Limit: Frequency(MHz) Field strength(microvolts/meter) Measurement distance(meters) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 Remark: The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands 9-90kHz, 110-490kHz. Radiated emission limits in these three bands are based on measurements employing an average detector, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. If field strength is measured at only a single point, then that point shall be at the radial from the EUT that produces the maximum emission at the frequency being measured, as described in 5.4. If that point is closer to the EUT than λ/2π and the limit distance is greater than λ/2π, the measurement shall be extrapolated to the limit distance by conservatively presuming that the field strength decreases at a 40 dB/decade of distance rate to the λ/2π distance, and at a 20 dB/decade of distance rate beyond λ/2π. This shall be accomplished using Equation (2): FS(10m) = FS(30/300m) + 40log{d(near field)/d(10m)} + 20log{d(30/300m)/d(near field)} (2) If the single point measured is at a distance greater than λ/2π, then extrapolation to the limit distance shall be calculated using Equation (3): FS(10m) = FS(30/300m) + 20log{d(30/300m)/d(10m)} (3) If both the single point and the limit distance are equal to or closer to the EUT than λ/2π, then extrapolation to the limit distance shall be calculated using Equation (4): FS(10m) = FS(30/300m) + 40log{d(30/300m)/d(10m)} (4) Remark: dnear field = 47.77 / fMHz where f MHz is the frequency of the emission being measured in MHz.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 20 of 29 7.4.1 E.U.T. Operation Operating Environment: Temperature: 23 °C Humidity: 55 % RH Atmospheric Pressure: 1000 mbar Pretest these a:Charge mode_Keep the EUT charging(5W ). modes to find b:Charge mode_Keep the EUT charging(7.5W). the worst case: c:Charge mode_Keep the EUT charging(10W). d:Charge mode_Keep the EUT charging(15W). The worst case c:Charge mode_Keep the EUT charging(10W). for final test: 7.4.2 Test Setup Diagram 7.4.3 Measurement Procedure and Data For testing performed with the loop antenna, the center of the loop was positioned 1 m above the ground and positioned with its plane vertical at the specified distance from the EUT. During testing the loop was rotated about its vertical axis for maximum response at each azimuth and also investigated with the loop positioned in the horizontal plane. Only the worst position of vertical was shown in the report.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 21 of 29 Mode:c 9kHz-150KHz

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 22 of 29 150kHz-30MHz

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 23 of 29 7.5 Radiated Emissions (30MHz-1GHz) Test Requirement 47 CFR Part 15, Subpart C 15.205 & 15.209 Test Method: ANSI C63.10 (2013) Section 6.5 Measurement Distance: 10m Limit: Frequency(MHz) Field strength(microvolts/meter) Measurement distance(meters) 30-88 100 3 88-216 150 3 216-960 200 3 Above 960 500 3 Remark: The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 24 of 29 7.5.1 E.U.T. Operation Operating Environment: Temperature: 23 °C Humidity: 55 % RH Atmospheric Pressure: 1000 mbar Pretest these a:Charge mode_Keep the EUT charging(5W ). modes to find b:Charge mode_Keep the EUT charging(7.5W). the worst case: c:Charge mode_Keep the EUT charging(10W). d:Charge mode_Keep the EUT charging(15W). The worst case c:Charge mode_Keep the EUT charging(10W). for final test: 7.5.2 Test Setup Diagram

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 25 of 29 7.5.3 Measurement Procedure and Data a. The EUT was placed on the top of a rotating table 0.8 meters above the ground for below 1GHz at a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. g. Test the EUT in the lowest channel,the middle channel,the Highest channel h. The radiation measurements are performed in X, Y, Z axis positioning for Transmitting mode,And found the X axis positioning which it is worse case. i. Repeat above procedures until all frequencies measured was complete. Remark: Level= Read Level+ Cable Loss+ Antenna Factor- Preamp Factor

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 26 of 29 Mode:c; Polarization:Horizontal

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 27 of 29 Mode:c; Polarization:Vertical

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 28 of 29 The test was performed at a 10m test site. According to below formulate and the test data at 10m test distance, L3 / L10 = D10 / D3 Note: L3: Level @ 3m distance. Unit: uV/m; L10: Level @ 10m distance. Unit: uV/m; D3: 3m distance. Unit: m D10: 10m distance. Unit: m The level at 3m test distance is below: Level @ Frequency Level @ Level @ 3m Level @ 3m Limit @ 3m Ant. 10m Margin (dB) (MHz) 10m (uV/m) (uV/m) (dBuV/m) (dBuV/m) Polarization (dBuV/m) 32.86 24.59 16.96 56.54 35.05 40.00 -4.95 V 54.26 22.26 12.97 43.24 32.72 40.00 -7.28 V 140.84 20.18 10.21 34.03 30.64 43.50 -12.86 V 383.93 21.59 12.01 40.03 32.05 46.00 -13.95 V 739.66 27.81 24.58 81.92 38.27 46.00 -7.73 V 938.83 29.60 30.20 100.67 40.06 46.00 -5.94 V 31.29 18.97 8.88 29.61 29.43 40.00 -10.57 H 37.68 15.49 5.95 19.83 25.95 40.00 -14.05 H 144.84 16.21 6.46 21.55 26.67 43.50 -16.83 H 366.82 21.47 11.84 39.48 31.93 46.00 -14.07 H 737.07 28.46 26.49 88.28 38.92 46.00 -7.08 H 912.86 30.09 31.95 106.51 40.55 46.00 -5.45 H

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM190801754401 Page: 29 of 29 8 Photographs 8.1 Test Setup Please refer to setup photos. 8.2 EUT Constructional Details (EUT Photos) Please refer to external and internal photos for details. - End of the Report -


Document Created: 2019-09-24 15:05:24
Document Modified: 2019-09-24 15:05:24
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC