15_WF-Q379-USA1 UserMan-US r1

FCC ID: 2AFG6-WF-Q379-USA1

Users Manual

Download: PDF
FCCID_4335681

WF-Q379-USA1Series IEEE 802.11a/b/g/n/ac 2T2R USB WiFi Module 特性 Features：  接收制式 Reserving System IEEE Std. 802.11a IEEE Std. 802.11b IEEE Std. 802.11g IEEE Std. 802.11n IEEE Std. 802.11ac  芯片方案 Chip Solution Qualcomm 9379-7  结构大小 Size 18.0mm x 27.0mm x 3.0mm 型号预览 Model Overview： 型号 安装方式 支持标准 速率 频段 天线接口 备注 3.3V WF-Q379-USA1 SMD IEEE 802.11a/b/g/n/ac 866.7Mbps 2.4G/5G 外置天线 供电 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. 地址 Add: 四川省绵阳市安州工业园区 Anzhou,Industrial park,Mianyang,Sichuan 传真 Fax : +86-0816-2416943 网址 : http://www.changhong.com

WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 客户确认反馈 Feedback of customer’s Confirmation 经确认，我方承认该规格书 We accept the specification after Confirmed 客户名称 客户签字 确认日期 Customer name Customer signature Confirmation Date 请签字后将此页与首页按以下地址回传我公司，谢谢！ Please feed back this paper and first paper after your signature by the address,thanks! 地址：四川省绵阳市安州工业园区 ADD： Anzhou,Industrial park,Mianyang,Sichuan 公司：四川爱联科技有限公司 Factory： Sichuan AI-Link Technology Co.,Ltd. 批准 审核 拟制 产品 无线模块 Approved Checked Designed Product WiFi Module 型号 WF-Q379-USA1 Model 日期 2018-03-06 Date 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 2 of 16

WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 更改记录 Record of Modification 更改日期 主要更改内容 更改原因 更改通知编号 序号 确认 Date of Main content of Reason of Serial number of No Confirm modification modification modification modification 1 2018/03/06 首次承认 黄伟 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 3 of 16

WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 1. Introduction WF-Q379-USA1 module design is based on Qualcomm 9379-7 solution, The QCA9379-7 is a highly integrated single chip which has built in a 2x2 dual-band wireless LAN radio. The Module is a highly integrated MAC/BBP and 2.4/5GHz PA/LNA single chip which supports a 866.7Mbps PHY rate. The Module is designed to support standard-based features in the areas of security, quality of service, and international regulations, giving end users the greatest performance anytime and in any circumstance. This documentation describes the engineering requirements specification. 1.1 RF module Overview The general HW architecture for the module is shown in Figure 1. This WLAN Module design is based on Qualcomm QCA9379-7. It is a highly integrated single-chip MIMO(Multiple In Multiple Out) Wireless LAN (WLAN) network interface controller complying with the 802.11 specification and Bluetooth over USB interface. It combines a MAC, a 2T2R capable baseband, and RF in a single chip. An intelligent Wi-Fi coexistence algorithm is implemented to provide the best harmonized Wi-Fi radio performance. 3.3V INPUT 2.4G TX0/RX0 GPIO WF_ Dixplexer Antenna0 RFIO 5G TX0/RX0 WLAN USB2.0 Interface QCA9379-7 2.4G TX1/RX1 WF_ Dixplexer Antenna1 RFIO 5G TX1/RX1 48MHz Figure 1 WF-Q379-USA1 Block Diagram 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 4 of 16

WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 1.2 Specification reference This specification is based on additional references listed below. _ IEEE Std. 802.11a _ IEEE Std. 802.11b _ IEEE Std. 802.11g _ IEEE Std. 802.11n _ IEEE Std. 802.11ac 1.3 System Functions Table1: General Specification as below: Main Chipset Qualcomm QCA9379-7 Operating Frequency 2.4G/5G WiFi Standard 802.11a/b/g/n/ac (2x2) Modulation WIFI:11b: DBPSK, DQPSK and CCK and DSSS 11a/g: BPSK, QPSK, 16QAM, 64QAM and OFDM 11n: BPSK, QPSK, 16QAM, 64QAM and OFDM 11ac: BPSK, QPSK, 16QAM, 64QAM,256QAM and OFDM Data rates 11b: 1, 2, 5.5 and 11Mbps 11a/g: 6, 9, 12, 18, 24, 36, 48 and 54 Mbps 11n: MCS0~15, up to 300Mbps 11ac: MCS0~9, Nss=2, up to 866.7Mbps Form factor 32pins , Host Interface USB 2.0 for WLAN PCB Stack 6-layers design Dimension Typical，18mm x 27mm x 3mm Antenna External Antennas Design Operation Temperature 0℃ to +70℃ Storage Temperature -15℃ to +45℃ Operation Voltage 3.3V +/-10% 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 5 of 16

WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 2. Mechanical Specification 2.1 Mechanical Outline Drawing Typical Dimension (W x L x H): 18.0mm x 27.0mm x 3.0mm General tolerance: ±0.15mm 2.2 Pin definition TOP VIEW 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 6 of 16

WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module Pin Define Description Pin Define Description 1 NC NC 17 NC NC 2 NC NC 18 GND Ground 3 NC NC 19 WL_RF0 Wi-Fi RF port0，connect to external antenna 4 NC NC 20 GND Ground 5 GND Ground 21 GND Ground 6 WL_USB_DP WLAN USB2.0 DP Signal 22 WL_RF1 Wi-Fi RF port1，connect to external antenna 7 WL_USB_DM WLAN USB2.0 DM Signal 23 GND Ground 8 GND Ground 24 GND Ground 9 NC NC 25 GND Ground 10 NC NC 26 QOW(GPIO General GPIO single. 35) 11 GND Ground 27 BT_EN Bluetooth enable，active high 12 BT_RF BT RF Output，connect to 28 WLAN_EN WLAN enable，active external antenna high 13 GND Ground 29 GND Ground 14 BT_WAKE_HOST Bluetooth wakeup the host， 30 VDD_3.3V 3.3V input (GPIO24) active high 15 HOST_WAKE_BT Host wakeup Bluetooth 31 3D_SYNC Frame sync signals from (GPIO33) through UART，active low (GPIO34) TV to sync with 3D glass via Bluetooth 16 NC NC 32 GND Ground 2.3 Product Picture 2.4 TOP VIEW BOTTOM VIEW 丝印说明: 1、红色框内为我司 PCB 图号； 2、橙色框内为生产批次号； 3、黄色框内为阻燃标志； 4、蓝色框内为 SMT 管控丝印； 5、紫色框内为天线通道说明； 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 7 of 16

WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 3. Electrical Specification This Specification is based-on conductive DVT testing result. The extreme condition include overall temperature (0℃,+25℃,+40℃) and overall voltage (3.0V,3.3V,3.6V). 3. 1 IEEE 802.11g/a Section: Items Contents Specification IEEE802.11g & IEEE802.11a Mode BPSK, QPSK, 16QAM, 64QAM and OFDM CH1 to CH13 @ 11g Channel CH36 to CH165 @ 11a Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels 1) 16.5dBm Target (For Each antenna port) 14.5 16.5 18.5 dBm @ 11g/6Mbps~24Mbps 2) 16dBm Target (For Each antenna port) 14 16 18 dBm @ 11g 36Mbps 3) 15.5dBm Target (For Each antenna port) 13.5 15.5 17.5 dBm @ 11g 48Mbps 4) 14.5dBm Target (For Each antenna port) 12.5 14.5 16.5 dBm @ 11g 54Mbps 5) 15.5dBm Target (For Each antenna port) 13.5 15.5 17.5 dBm @ 11a/6Mbps~36Mbps 6) 14.5dBm Target (For Each antenna port) 12.5 14.5 16.5 dBm @ 11a 48Mbps 7) 13.5dBm Target (For Each antenna port) 11.5 13.5 15.5 dBm @ 11a 54Mbps 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz - - -20 dBr 2) at fc +/-20MHz - - -28 dBr 3) at fc > +/-30MHz - - -40 dBr 3. Constellation Error(EVM) @ Target Power 1) 6Mbps - - -5 dB 2) 9Mbps - - -8 dB 3) 12Mbps - - -10 dB 4) 18Mbps - - -13 dB 5) 24Mbps - - -16 dB 6) 36Mbps - - -19 dB 7) 48Mbps - - -22 dB 8) 54Mbps - - -25 dB 4. Frequency Error 1) IEEE802.11g -25 - 25 ppm 2) IEEE802.11a -30 30 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) 6Mbps (PER ≦10%) - - -82 dBm 2) 9Mbps (PER ≦10%) - - -81 dBm 3) 12Mbps (PER ≦10%) - - -79 dBm 4) 18Mbps (PER ≦10%) - - -77 dBm 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 8 of 16

WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 5) 24Mbps (PER ≦10%) - - -74 dBm 6) 36Mbps (PER ≦10%) - - -70 dBm 7) 48Mbps (PER ≦10%) - - -66 dBm 8) 54Mbps (PER ≦10%) - - -65 dBm 6. Maximum Input Level (PER ≦10%) 1) IEEE802.11g -20 - - dBm 2) IEEE802.11a -30 dBm 3.2 IEEE 802.11b Section: Items Contents Specification IEEE802.11b Mode DBPSK, DQPSK and CCK and DSSS Channel CH1 to CH13 Data rate 1, 2, 5.5, 11Mbps TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels(Calibrated) 1) 17dBm Target (For Each antenna port) 15.5 17.5 19.5 dBm @1Mbps~11Mbps 2. Spectrum Mask @ Target Power 1) fc +/-11MHz to +/-22MHz - - -30 dBr 2) fc > +/-22MHz - - -50 dBr 3. Constellation Error(EVM) @ Target Power 1) 1Mbps - - -10 dB 2) 2Mbps - - -10 dB 3) 5.5Mbps - - -10 dB 4) 11Mbps - -20 -10 dB 4. Frequency Error -25 - 25 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) 1Mbps (FER ≦8%) - -83 -76 dBm 2) 2Mbps (FER ≦8%) - -80 -76 dBm 3) 5.5Mbps (FER ≦8%) - -79 -76 dBm 4) 11Mbps (FER ≦8%) - -76 -76 dBm 6. Maximum Input Level (FER ≦8%) -10 - - dBm 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 9 of 16

WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 3.3 IEEE 802.11n HT20 Section: Items Contents IEEE802.11n HT20 @ 2.4G Specification IEEE802.11n HT20 @ 5G Mode BPSK, QPSK, 16QAM, 64QAM and OFDM CH1 to CH13 @ 2.4G Channel CH36 to CH165 @ 5G Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels 1) 16.5dBm Target (For Each antenna port) 14.5 16.5 18.5 dBm @ 2.4G/MCS0~MCS2 2) 16dBm Target (For Each antenna port) 14 16 18 dBm @ 2.4G/MCS3~MCS4 3) 15dBm Target (For Each antenna port) 13 15 17 dBm @ 2.4G/MCS5~MCS6 4) 14.5dBm Target (For Each antenna port) 12.5 14.5 16.5 dBm @ 2.4G/MCS7 5) 15.5dBm Target (For Each antenna port) 13.5 15.5 17.5 dBm @ 5G/MCS0~MCS2 6) 15dBm Target (For Each antenna port) 13 15 17 dBm @ 5G/MCS3~MCS5 7) 14.5dBm Target (For Each antenna port) 12.5 14.5 16.5 dBm @ 5G/MCS6 8) 13.5dBm Target (For Each antenna port) 11.5 13.5 15.5 dBm @ 5G/MCS7 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz - - -20 dBr 2) at fc +/-20MHz - - -28 dBr 3) at fc > +/-30MHz - - -45 dBr 3. Constellation Error(EVM) @ Target Power 1) MCS0 - - -5 dB 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - - -28 dB 4. Frequency Error 1) IEEE802.11n HT20 @ 2.4G -25 - 25 ppm 2) IEEE802.11n HT20 @ 5G -20 - 20 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER ≦10%) - - -82 dBm 2) MCS1 (PER ≦10%) - - -79 dBm 3) MCS2 (PER ≦10%) - - -77 dBm 4) MCS3 (PER ≦10%) - - -74 dBm 5) MCS4 (PER ≦10%) - - -70 dBm 6) MCS5 (PER ≦10%) - - -66 dBm 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 10 of 16

WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 7) MCS6 (PER ≦10%) - - -65 dBm 8) MCS7 (PER ≦10%) - - -64 dBm 6. Maximum Input Level (PER ≦10%) 1) IEEE802.11n HT20 @ 2.4G -20 - - dBm 2) IEEE802.11n HT20 @ 5G -30 - - dBm 3.4 IEEE 802.11n HT40 Section: Items Contents IEEE802.11n HT20 @ 2.4G Specification IEEE802.11n HT20 @ 5G Mode BPSK, QPSK, 16QAM, 64QAM and OFDM CH3 to CH11 @ 2.4G Channel CH38 to CH163 @ 5G Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels (Calibrated) 1) 15.5dBm Target (For Each antenna port) 13.3 15.5 17.5 dBm @ 2.4G/MCS0~MCS2 2) 15dBm Target (For Each antenna port) 13 15 17 dBm @ 2.4G/MCS3~MCS4 3) 14dBm Target (For Each antenna port) 12 14 16 dBm @ 2.4G/MCS5~MCS6 4) 13.5dBm Target (For Each antenna port) 11.5 13.5 15.5 dBm @ 2.4G/MCS7 5) 14.5dBm Target (For Each antenna port) 12.5 14.5 16.5 dBm @ 5G/MCS0~MCS2 6) 14dBm Target (For Each antenna port) 12 14 16 dBm @ 5G/MCS3~MCS5 7) 13.5dBm Target (For Each antenna port) 11.5 13.5 15.5 dBm @ 5G/MCS6 8) 12.5dBm Target (For Each antenna port) 10.5 12.5 14.5 dBm @ 5G/MCS7 2. Spectrum Mask @ Target Power 1) at fc +/-21MHz - - -20 dBr 2) at fc +/-40MHz - - -28 dBr 3) at fc > +/-60MHz - - -45 dBr 3. Constellation Error(EVM) @ Target Power 1) MCS0 - - -5 dB 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - - -28 dB 4. Frequency Error 1) IEEE802.11n HT20 @ 2.4G -25 - 25 ppm 2) IEEE802.11n HT20 @ 5G -20 - 20 ppm RX Characteristics Min. Typ. Max. Unit 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 11 of 16

WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 5. Minimum Input Level Sensitivity(each chain) 1) MCS0 (PER ≦10%) - - -79 dBm 2) MCS1 (PER ≦10%) - - -76 dBm 3) MCS2 (PER ≦10%) - - -74 dBm 4) MCS3 (PER ≦10%) - - -71 dBm 5) MCS4 (PER ≦10%) - - -67 dBm 6) MCS5 (PER ≦10%) - - -63 dBm 7) MCS6 (PER ≦10%) - - -62 dBm 8) MCS7 (PER ≦10%) - - -61 dBm 6. Maximum Input Level(PER ≦10%) 1) IEEE802.11n HT20 @ 2.4G -20 - - dBm 2) IEEE802.11n HT20 @ 5G -30 - - dBm 3.5 IEEE 802.11ac Section: Items Contents Specification IEEE802.11ac Mode BPSK, QPSK, 16QAM, 64QAM ,256QAM and OFDM CH36 to CH165 VHT20 Channel CH38 to CH163 VHT40 CH42 to CH157 VHT80 Data rate (MCS index) MCS0/1/2/3/4/5/6/7/8/9 TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels (Calibrated) 1) 15.5dBm Target (For Each antenna port) 13.5 15.5 17.5 dBm @VHT20 MCS0~MCS2 2) 15dBm Target (For Each antenna port) 13 15 17 dBm @VHT20 MCS3~MCS5 3) 14.5dBm Target (For Each antenna port) 12.5 14.5 16.5 dBm @VHT20 MCS6 4) 13.5dBm Target (For Each antenna port) 11.5 13.5 15.5 dBm @VHT20 MCS7 5) 12.5dBm Target (For Each antenna port) 10.5 12.5 14.5 dBm @VHT20 MCS8 6) 14.5dBm Target (For Each antenna port) 12.5 14.5 16.5 dBm @VHT40 MCS0~MCS2 7) 14dBm Target (For Each antenna port) 12 14 16 dBm @VHT40 MCS3~MCS5 8) 13.5dBm Target (For Each antenna port) 11.5 13.5 15.5 dBm @VHT40 MCS6 9) 12.5dBm Target (For Each antenna port) 10.5 12.5 14.5 dBm @VHT40 MCS7 10) 11.5dBm Target (For Each antenna port) 9.5 11.5 13.5 dBm @VHT40 MCS8 11) 10.5dBm Target (For Each antenna port) 8.5 10.5 12.5 dBm @VHT40 MCS9 12) 13.5dBm Target (For Each antenna port) 11.5 13.5 15.5 dBm 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 12 of 16

WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module @VHT80 MCS0~2 13) 13dBm Target (For Each antenna port) 11 13 15 dBm @VHT80 MCS3~5 14) 12.5dBm Target (For Each antenna port) 10.5 12.5 14.5 dBm @VHT80 MCS6 15) 11.5dBm Target (For Each antenna port) 9.5 11.5 13.5 dBm @VHT80 MCS7 16) 10.5dBm Target (For Each antenna port) 8.5 10.5 12.5 dBm @VHT80 MCS8 17) 9.5dBm Target (For Each antenna port) 7.5 9.5 11.5 dBm @VHT80 MCS9 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz /20MHz/30MHz - - -20 dBr 2) at fc +/-21MHz /40MHz/60MHz - - -28 dBr 3) at fc +/-41MHz /80MHz/120MHz - - -40 dBr 3. Constellation Error(EVM) @ Target Power 1) MCS0 - - -5 dB 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - - -27 dB 9) MCS8 -30 dB 10) MCS9 -32 dB 4. Frequency Error -10 - 10 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity(each chain) VHT20 VHT40 VHT80 1) MCS0 (PER ≦10%) - - -82 -79 -76 dBm 2) MCS1 (PER ≦10%) - - -79 -76 -73 dBm 3) MCS2 (PER ≦10%) - - -77 -74 -71 dBm 4) MCS3 (PER ≦10%) - - -74 -71 -68 dBm 5) MCS4 (PER ≦10%) - - -70 -67 -64 dBm 6) MCS5 (PER ≦10%) - - -66 -63 -60 dBm 7) MCS6 (PER ≦10%) - - -65 -62 -59 dBm 8) MCS7 (PER ≦10%) - - -64 -61 -58 dBm 9) MCS8 (PER ≦10%) - - -59 -56 -53 dBm 10) MCS9 (PER ≦10%) - - -57 -54 -51 dBm 6. Maximum Input Level(PER ≦10%) -30 - - dBm 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 13 of 16

WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 4. Software Requirements The driver supports the following operating systems: Linux, Microsoft Windows XP, Vista and Win7. Mfg. software tool is QDART. 5. Antenna matching The BT RF ，ANT0 and ANT1 Pin connect to antenna, please refer to design demand a). 模块和天线要求远离干扰源，模块地和天线地要求为一个整体。 b). PIN12,PIN19和PIN22为模组的RF接口，与天线之间布线要求共面阻抗为50Ω，建议使用弧线和直线，长 度尽可能短。 c). L1, L2, C1组成π型匹配网络并靠近天线接口设计，具体根据天线推荐及排版设计的实测效果进行调整。 6. Key component List 序 关键件名称 型号 规格/材料 生产者 备注 号 1 集成电路 QCA9379-7 QFN Qualcomm 顺 络 2 PCB JUI7.820. 0317系列 FR-6,4LAY 英 创 力 昌盛艺龙 晶 威 特 Hosonic 3 晶体振荡器 SMD2520-48M 加高 TXC ACX TDK 4 双工器 1608 华新科 顺络 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 14 of 16

WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 7. Packaging Information: 编带尺寸： 编带方向：（箭头代表编带走向） 包装示意图： 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 15 of 16

WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 注：上图 3 个框示处为内盒标签粘贴位置。 注：红色箭头处为外箱标签粘贴位置。 标签样式： 内盒标签示例 外箱装箱清单标签示例 包装说明： 1. 产品放置方向、标签粘贴位置、包装按示意图进行； 2. 每卷放600只产品，每小盒放1卷，大箱共5装个小盒，产品数量共3000只/箱; 3. 外箱尺寸：378mm*297mm*370mm，小盒尺寸：355mm*355mm*50mm; 4. 真空包内放置2g干燥剂2袋，6色湿度卡1张; 5.其它按CVTE包装要求执行; 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 16 of 16

FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC ID: 2AFG6-WF-Q379-USA1” any similar wording that expresses the same meaning may be used. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. The module is limited to installation in mobile or fixed application. A separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and difference antenna configurations. There is requirement that the grantee provide guidance to the host manufacturer for compliance with Part 15B requirements

Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules Part 15.247 and Part 15.407 2.3 Specific operational use conditions The module is limited to installation in mobile or fixed application. A separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and difference antenna configurations. 2.4 Limited module procedures Not applicable as this is not a limited modular. 2.5 Trace antenna designs Not applicable as there is no trace antenna design in this modular. 2.6 RF exposure considerations For the end host, the antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. 2.7 Antennas For BT&LE Ant. Brand P/N Antenna Type Connector Gain (dBi) 1 TB-SR-41Y Dipole N/A 2.76 For WIFI 2.4G &5G Ant. Brand Model Name Antenna Type Connector Gain (dBi) 3.95(2.4G) 1 N/A PCB N/A 3.33(5G) 3.95(2.4G) 2 N/A PCB N/A 3.33(5G) 2.8 Label and compliance information Host product manufacturers are required to provide a physical or e-label stating “Contains FCC ID: 2AFG6-WF-Q379-USA1” with their finished product. 2.9 Information on test modes and additional testing requirements Test modes should take into consideration different operational conditions for a stand-alone

modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product. 2.10 Additional testing, Part 15 Subpart B disclaimer This modular transmitter is only FCC authorized for FCC Part 15.247&15.407 as listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.


Document Created: 2019-06-21 10:34:47
Document Modified: 2019-06-21 10:34:47
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC