Antenna Taoglas ALA.01.07.0095A

FCC ID: 2AFDI-ITCOQ626S

Operational Description

Download: PDF
FCCID_4291295

SPECIFICATION Part No. : AP.17F.07.0064A Product Name : 17mm Two Stage GPS/GALILEO Active Patch Antenna Module Features : 22.2mm*23.8mm*7.8mm 64mm 1.13 IPEX MHFI Wide Voltage Input 1.8V to 5.5V 28dB LNA Tested in Free space RoHS Compliant SPE-11-8-145/D/SS Page 1 of 10

1. Introduction The AP.17F is a two stage 17mm active patch antenna that has been designed specifically for embedded (inside device) integration with GPS/GALILEO receiver modules. The AP.17F combines a 17*17*4mm advanced low profile ceramic patch antenna with a one stage LNA and a front-end SAW filter with ultra thin coaxial cable. It comes with it’s own integrated ground-plane. The front end SAW filter reduces the risks where there is a cellular transmitter nearby of interference from out of band frequencies which can cause LNA burn-out, saturation, or radiated spurious emissions. The antenna can work on a wide input voltage from 1.8V to 5.5V with best in class power consumption figures. If further tuning and optimization specific to a customer device is required Taoglas offers a custom tuned and optimized part service. Contact sales@taoglas.com for more information. Cables and connectors can be customized according to request. ANTENNA SAW Filter LNA I-PEX +cable SPE-11-8-145/D/SS Page 2 of 10

2. Specifications ELECTRICAL Input Voltage Min:1.8V Typ.: 3.0V Max: 5.5V Frequency Range 1575.42MHz +/- 1.023 MHz Gain -1.5dBic Typ. @zenith Polarization RHCP Axial ratio Max 3.0dB@zenith Frequency Range 1575.42MHz +/- 1.023 MHz At 90° At 5.5V 22.5 ± 3dBic Gain (With LNA) At 3.0V 29.5 ± 3dBic At 1.8V 32.5 ± 3dBic Output Impedance 50Ω LNA Frequency 1575.42 ± 1.023MHz F0=1575.42MHz F0±30MHz 6dB min. Outer Band Attenuation F0±50MHz 20dB min. F0±100MHz 25dB min. Output Impedance 50Ω Output VSWR 2.0 Max Pout at 1dB Gain Typ. -5dBm Compression point Min. -9dBm LNA Gain, Power Consumption and Noise Figure LNA Gain Power Consumption Noise Figure Voltage (Typ) (mA) Typ Typ Min. 1.8V 21dB 3.3mA 2.7dB Typ. 3.0V 28dB 7.5mA 2.5dB Max. 5.5V 31dB 15.5mA 2.7dB SPE-11-8-145/D/SS Page 3 of 10

MECHANICAL RF Cable Ø1.13 RF Coaxial Cable L=64mm1.5mm RF Connector I-PEX(MHF) - U.FL Comp. Dimensions 22.2mm*23.8mm*7.8mm ENVIRONMENTAL Operation Temperature -40°C to + 85°C Storage Temperature -40°C to + 85°C Relative Humidity 40% to 95% SPE-11-8-145/D/SS Page 4 of 10

2.1. LNA Gain and Out Band Rejection @3.0V 2.2. LNA Noise Figure @3.0V SPE-11-8-145/D/SS Page 5 of 10

3. Radiation Patterns XY Plane XZ Plane YZ Plane SPE-11-8-145/D/SS Page 6 of 10

4. Plugs Usage Precautions 4.1. Mating / Unmating (1) To disconnect connectors, insert the end portion of I-PEX under the connector flanges and pull off vertically, in the direction of the connector mating axis. (2) To mate the connectors, the mating axes of both connectors must be aligned and the connectors can be mated. The "click" will confirm fully mated connection. Do not attempt +Z to insert on an extreme angle. +X 4.2. Pull forces on the cable after connectors are mated After the connectors are mated, do not apply a load to the cable in excess of the values indicated in the diagram below. SPE-11-8-145/D/SS Page 7 of 10

5. Mechanical Drawing (Unit: mm) SPE-11-8-145/D/SS Page 8 of 10

6. Packaging SPE-11-8-145/D/SS Page 9 of 10

Taoglas makes no warranties based on the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Taoglas reserves all rights to this document and the information contained herein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. Copyright © Taoglas Ltd. SPE-11-8-145/D/SS Page 10 of 10


Document Created: 2018-11-09 14:12:02
Document Modified: 2018-11-09 14:12:02
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC