Modular Application Letter

FCC ID: 2AFDI-ITCOQ626S

Cover Letter(s)

Download: PDF
FCCID_4285224

Applicant/Grantee Intrinsyc Technologies Corporation FCC ID: 2AFDI-ITCOQ626S Section 15.212 Modular Transmitters Request For Modular Approval Requirements EUT Conditions Comply (Y/N) Single Modular Approval Requirements 1 The radio elements of the modular Device is equipped with metal Y transmitter must have their own shielding to cover the RF sections. shielding. The physical crystal and Refer to external photos tuning capacitors may be located external to the shielded radio elements. 2 The modular transmitter must have All inputs to the modules are Y buffered modulation/data inputs (if buffered through logic or such inputs are provided) to ensure microprocessor inputs. that the module will comply with Part 15 requirements under conditions of excessive data rates or over- modulation. 3 The modular transmitter must have Provided by PM8953 and Y its own power supply regulation. PMI8952 Power management integrated circuits. Refer to Block Diagram 4 The modular transmitter must comply Device is equipped with unique Y with the antenna and transmission antenna U.FL connector. system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. 5 The modular transmitter must be Device was tested in stand-alone Y tested in a stand-alone configuration, configuration on a carrier board. i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines

and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)). 6 The modular transmitter must be One proposed FCC ID label format Y equipped with either a permanently is included in the filing. The label affixed label or must be capable of is to be placed on the module. electronically displaying its FCC Labeling instructions are also identification number. provided for integrators of the (A) If using a permanently affixed module in the Module label, the modular transmitter must Certification TechNote68 OEM be labeled with its own FCC Integrator Guide document. identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization.

(B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. 7 The modular transmitter must comply Refer to Module Certification Y with any specific rules or operating TechNote68 OEM Integrator requirements that ordinarily apply to Guide document. a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. 8 The modular transmitter must comply Transmitter meets MPE Y with any applicable RF exposure calculation of 47 CFR 1.1307 (b) requirements in its final (1). Refer to configuration. MPE section of the test reports.


Document Created: 2019-03-29 16:56:43
Document Modified: 2019-03-29 16:56:43
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC