Test Report

FCC ID: 2AEZ5M-US1

Test Report

Download: PDF
FCCID_2677262

JMA Alejandro Altuna S.L.U. Model: M-US1 FCC Part 15C Measurement and Test Report For JMA Alejandro Altuna S.L.U. BIDEKURTZETA 6, ARRASATE, GIPUZKOA, SPAIN FCC ID: 2AEZ5M-US1 FCC Rules: FCC Part 15.231 Product Description: Remote Control Transmitter Tested Model: M-US1 Report No.: STR15058166I Tested Date: 2015-05-21 to 2015-07-03 Issued Date: 2015-07-03 Tested By: Jong Wang / Engineer Reviewed By: Lahm Peng / EMC Manager Approved & Authorized By: Jandy so / PSQ Manager Prepared By: Shenzhen SEM.Test Technology Co., Ltd. 1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C.（518101） Tel.: +86-755-33663308 Fax.: +86-755-33663309 Website: www.semtest.com.cn Note: This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen SEM. Test Technology Co., Ltd. REPORT NO.: STR15058166I PAGE 1 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 TABLE OF CONTENTS 1. GENERAL INFORMATION ...................................................................................................................................3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ...............................................................................3 1.2 TEST STANDARDS...................................................................................................................................................4 1.3 TEST METHODOLOGY .............................................................................................................................................4 1.4 TEST FACILITY .......................................................................................................................................................4 1.5 EUT SETUP AND TEST MODE .................................................................................................................................5 2. SUMMARY OF TEST RESULTS ...........................................................................................................................6 3. ANTENNA REQUIREMENT ..................................................................................................................................7 3.1 STANDARD APPLICABLE.........................................................................................................................................7 3.2 TEST RESULT..........................................................................................................................................................7 4. RADIATED EMISSIONS .........................................................................................................................................8 4.1 MEASUREMENT UNCERTAINTY ..............................................................................................................................8 4.2 STANDARD APPLICABLE.........................................................................................................................................8 4.3 TEST EQUIPMENT LIST AND DETAILS .....................................................................................................................9 4.4 TEST PROCEDURE ...................................................................................................................................................9 4.5 CORRECTED AMPLITUDE & MARGIN CALCULATION ............................................................................................10 4.6 ENVIRONMENTAL CONDITIONS ............................................................................................................................10 4.7 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................10 5. 20DB BANDWIDTH ...............................................................................................................................................13 5.1 STANDARD APPLICABLE.......................................................................................................................................13 5.2 TEST EQUIPMENT LIST AND DETAILS ...................................................................................................................13 5.3 TEST PROCEDURE .................................................................................................................................................13 5.4 ENVIRONMENTAL CONDITIONS ............................................................................................................................13 5.5 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................13 6. TRANSMISSION TIME .........................................................................................................................................15 6.1 STANDARD APPLICABLE.......................................................................................................................................15 6.2 TEST EQUIPMENT LIST AND DETAILS ...................................................................................................................15 6.3 TEST PROCEDURE .................................................................................................................................................15 6.4 ENVIRONMENTAL CONDITIONS ............................................................................................................................15 6.5 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................15 7. DUTY CYCLE .........................................................................................................................................................17 7.1 STANDARD APPLICABLE.......................................................................................................................................17 7.2 TEST EQUIPMENT LIST AND DETAILS ...................................................................................................................17 7.3 TEST PROCEDURE .................................................................................................................................................17 7.4 ENVIRONMENTAL CONDITIONS ............................................................................................................................17 7.5 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................17 REPORT NO.: STR15058166I PAGE 2 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 1. GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) Client Information Applicant: JMA Alejandro Altuna S.L.U. Address of applicant: BIDEKURTZETA 6, ARRASATE, GIPUZKOA, SPAIN Manufacturer: Shenzhen C&D Electronics Co., Ltd Address of manufacturer: 9th Floor 9 Building no.1 Qingxing Road Baoneng Science and Technology Industrial Park Longhua New District Shenzhen City General Description of EUT Product Name: Remote Control Transmitter Trade Name: JMA, ERREBI Model No.: M-US1 Adding Model(s): / Rated Voltage: DC 3V Power Adaptor Model: / Note: The test data is gathered from a production sample, provided by the manufacturer. Technical Characteristics of EUT Frequency Range: 314.8125MHz Max. Field Strength: 87.97dBuV/m (at 3m distance) Data Rate: / Modulation: ASK Antenna Type: PCB Antenna Antenna Gain: 0dBi REPORT NO.: STR15058166I PAGE 3 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 1.2 Test Standards The following report is prepared on behalf of the JMA Alejandro Altuna S.L.U. in accordance with FCC Part 15, Subpart C, and section 15.231, 15.203, 15.205 and 15.209 of the Federal Communication Commissions rules. The objective is to determine compliance with FCC Part 15, Subpart C, and section 15.231, 15.203, 15.205 and 15.209 of the Federal Communication Commissions rules. Maintenance of compliance is the responsibility of the manufacturer. Any modification of the product, which result in lowering the emission/immunity, should be checked to ensure compliance has been maintained. 1.3 Test Methodology All measurements contained in this report were conducted with ANSI C63.4-2009, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the range of 9 kHz to 40 GHz. 1.4 Test Facility • FCC – Registration No.: 934118 Shenzhen SEM.Test Technology Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files and the Registration is 934118. • Industry Canada (IC) Registration No.: 11464A The 3m Semi-anechoic chamber of Shenzhen SEM.Test Technology Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 11464A. • CNAS Registration No.: L4062 Shenzhen SEM.Test Technology Co., Ltd. is a testing organization accredited by China National Accreditation Service for Conformity Assessment (CNAS) according to ISO/IEC 17025. The accreditation certificate number is L4062. All measurement facilities used to collect the measurement data are located at 1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C (518101) REPORT NO.: STR15058166I PAGE 4 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 1.5 EUT Setup and Test Mode The EUT was operated at continuous transmitting mode that was for the purpose of the measurements. All testing shall be performed under maximum output power condition, and to measure its highest possible emissions level, more detailed description as follows: Test Mode List Test Mode Description Remark TM1 Transmitting With modulation Special Cable List and Details Cable Description Length (m) Shielded/Unshielded With / Without Ferrite / / / / Auxiliary Equipment List and Details Description Manufacturer Model Serial Number / / / / REPORT NO.: STR15058166I PAGE 5 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 2. SUMMARY OF TEST RESULTS FCC Rules Description of Test Item Result §15.203 Antenna Requirement Compliant §15.205 Restricted Band of Operation Compliant §15.207(a) Conducted Emission Compliant §15.209 Radiated Spurious Emissions Compliant §15.231(a) Deactivation Testing Compliant §15.231(b) Radiated Emissions Compliant §15.231(c) 20dB Bandwidth Testing Compliant REPORT NO.: STR15058166I PAGE 6 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 3. Antenna Requirement 3.1 Standard Applicable According to FCC Part 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. 3.2 Test Result This product has a PCB antenna, fulfill the requirement of this section. REPORT NO.: STR15058166I PAGE 7 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 4. Radiated Emissions 4.1 Measurement Uncertainty Based on NIS 81, The Treatment of Uncertainty in EMC Measurements, the best estimate of the uncertainty of a radiation emissions measurement is +5.10 dB. 4.2 Standard Applicable According to §15.231(b), the field strength of emissions from intentional radiators operated under this section shall not exceed the following: The limits on the field strength of the spurious emissions in the above table are based on the fundamental frequency of the intentional radiator. Spurious emissions shall be attenuated to the average (or, alternatively, CISPR quasi-peak) limits shown in this table or to the general limits shown in §15.209, whichever limit permits a higher field strength. The emission limit in this paragraph is based on measurement instrumentation employing an average detector. The provisions in §15.35 for limiting peak emissions apply. Spurious Radiated Emissions measurements starting below or at the lowest crystal frequency. Compliance with the provisions of §15.205 shall be demonstrated using the measurement instrumentation specified in that section. REPORT NO.: STR15058166I PAGE 8 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 4.3 Test Equipment List and Details Description Manufacturer Model Serial Number Cal. Date Due. Date Spectrum Analyzer R&S FSP 836079/035 2015-05-28 2016-05-27 EMI Test Receiver R&S ESVB 825471/005 2015-05-28 2016-05-27 Pre-amplifier Agilent 8447F 3113A06717 2015-05-28 2016-05-27 Pre-amplifier Compliance Direction PAP-0118 24002 2015-05-28 2016-05-27 Trilog Broadband SCHWARZBECK VULB9163 9163-333 2015-05-28 2016-05-27 Antenna Horn Antenna ETS 3117 00086197 2015-05-28 2016-05-27 Loop Antenna SCHWARZECK HFRA 5165 9365 2015-05-28 2016-05-27 4.4 Test Procedure The setup of EUT is according with per ANSI C63.4-2009 measurement procedure. The specification used was with the FCC Part 15.205 15.231(b) and FCC Part 15.209 Limit. Antenna Tower 1m-4m 3m EUT 0.8m Turntable Table To EMI Receiver Ground Plane Frequency :9kHz-30MHz Frequency :30MHz-1GHz Frequency :Above 1GHz RBW=10KHz, RBW=120KHz, RBW=1MHz, VBW =30KHz VBW=300KHz VBW=3MHz(Peak), 10Hz(AV) Sweep time= Auto Sweep time= Auto Sweep time= Auto Trace = max hold Trace = max hold Trace = max hold Detector function = peak Detector function = peak, QP Detector function = peak, AV REPORT NO.: STR15058166I PAGE 9 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 4.5 Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and the Cable Factor, and subtracting the Amplifier Gain from the Amplitude reading. The basic equation is as follows: Corr. Ampl. = Indicated Reading +Ant.Loss +Cab. Loss – Ampl.Gain The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of -6dBμV means the emission is 6dBμV below the maximum limit. The equation for margin calculation is as follows: Margin = Corr. Ampl. – FCC Part 15C Limit 4.6 Environmental Conditions Temperature: 21° C Relative Humidity: 50% ATM Pressure: 1011 mbar 4.7 Summary of Test Results/Plots According to the data below, the FCC Part 15.205, 15.209 and 15.231 standards, and had the worst margin of: -8.55 dB at 314.9500MHz in the Horizontal polarization, Ave Detector, 9 kHz to 4 GHz, 3 Meters Note: this EUT was tested in 3 orthogonal positions and the worst case position data was reported. REPORT NO.: STR15058166I PAGE 10 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 Plot of Radiated Emissions Test Data EUT: Remote Control Transmitter Tested Model: M-US1 Operating Condition: Transmitting Comment: DC 3V Test Specification: Horizontal No. Frequency Reading Correct Dutycycle Result Limit Margin Degree Height Detector (MHz) (dBuV) (dB/m) Factor (dBuV/m) (dBuV/m) (dB) ( ) (cm) (dB) 1* 314.8125 68.64 12.27 N/A 80.91 95.62 -14.71 0 100 peak 314.8125 / / -8.60 72.31 75.62 -3.31 0 100 Ave 2 629.6250 35.02 18.33 N/A 53.35 75.62 -22.27 0 100 peak 629.6250 / / -8.60 44.75 55.62 -10.87 0 100 Ave 3 944.4375 36.03 16.25 N/A 52.28 75.62 -23.34 0 100 peak 944.4375 / / -8.60 43.68 55.62 -11.94 0 100 Ave Above 1GHz No. Frequency Reading Correct Dutycycle Result Limit Margin Degree Height Detector MHz dBuV/m Factor Factor dBuV/m dBuV/m dB (°) (cm) (dB) (dB) 1 1259.65 50.92 -8.43 N/A 42.49 74.00 -31.51 0 100 Peak 1259.65 / / -8.60 33.89 54.00 -20.11 0 100 Ave REPORT NO.: STR15058166I PAGE 11 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 Test Specification: Vertical No. Frequency Reading Correct Dutycycle Result Limit Margin Degree Height Detector (MHz) (dBuV) (dB/m) Factor (dBuV/m) (dBuV/m) (dB) ( ) (cm) (dB) 1* 314.8125 61.93 12.27 N/A 74.20 95.62 -21.42 0 100 Peak 314.8125 / / -8.60 65.60 75.62 -10.02 0 100 Ave 2 629.6250 25.61 18.33 N/A 43.94 75.62 -31.68 0 100 Peak 629.6250 / / -8.60 35.34 55.62 -20.28 0 100 Ave 3 944.4375 31.02 16.25 N/A 47.27 75.62 -28.35 0 100 Peak 944.4375 / / -8.60 38.67 55.62 -16.95 0 100 Ave Above 1GHz No. Frequency Reading Correct Dutycycle Result Limit Margin Degree Height Detector MHz dBuV/m Factor Factor dBuV/m dBuV/m dB (°) (cm) (dB) (dB) 1 1259.65 46.90 -8.43 N/A 38.47 74.00 -35.53 0 100 Peak 1259.65 / / -8.60 29.87 54.00 -24.13 0 100 Ave Note: Testing is carried out with frequency rang 9kHz to the tenth harmonics, which above 5th Harmonics are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. The measurements greater than 20dB below the limit from 9kHz to 30MHz. The fundamental frequency is 314.8125 the fundamental and spurious emissions radiated limit base on the operating frequency 314.8125MHz. REPORT NO.: STR15058166I PAGE 12 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 5. 20dB Bandwidth 5.1 Standard Applicable According to FCC Part 15.231(c), The bandwidth of the emission shall be no wider than 0.25% of the center frequency for devices operating above 70 MHz and below 900 MHz. Bandwidth is determined at the points 20 dB down from the modulated carrier. 5.2 Test Equipment List and Details Description Manufacturer Model Serial Number Cal. Date Due. Date Spectrum Analyzer Agilent E4402B US41192821 2015-05-28 2016-05-27 Attenuator ATTEN ATS100-4-20 / 2015-05-28 2016-05-27 5.3 Test Procedure With the EUT’s antenna attached, the EUT’s 20dB Bandwidth power was received by the test antenna, which was connected to the spectrum analyzer with the START, and STOP frequencies set to the EUT’s operation band. 5.4 Environmental Conditions Temperature: 21° C Relative Humidity: 52% ATM Pressure: 1011 mbar 5.5 Summary of Test Results/Plots Test Frequency 20dB Bandwidth Limit Result MHz kHz kHz 314.8125 54.86 787.03 Pass Limit = Fundamental Frequency X 0.25% = 314.8125 MHz X 0.25% = 787.03kHz Please refer to the attached plots. REPORT NO.: STR15058166I PAGE 13 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 20dB Bandwidth Test Plot REPORT NO.: STR15058166I PAGE 14 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 6. Transmission Time 6.1 Standard Applicable According to FCC Part 15.231 (a), the transmitter shall be complied the following requirements: 1) A manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released. (2) A transmitter activated automatically shall cease transmission within 5 seconds after activation. (3) Periodic transmissions at regular predetermined intervals are not permitted. However, polling or supervision transmissions, including data, to determine system integrity of transmitters used in security or safety applications are allowed if the total duration of transmissions does not exceed more than two seconds per hour for each transmitter. There is no limit on the number of individual transmissions, provided the total transmission time does not exceed two seconds per hour. 6.2 Test Equipment List and Details Description Manufacturer Model Serial Number Cal. Date Due. Date Spectrum Analyzer Agilent E4402B US41192821 2015-05-28 2016-05-27 Attenuator ATTEN ATS100-4-20 / 2015-05-28 2016-05-27 6.3 Test Procedure With the EUT’s antenna attached, the EUT’s output signal was received by the test antenna, which was connected to the spectrum analyzer. Set the center frequency to 314.8125MHz, than set the spectrum analyzer to Zero Span for the release time reading. During the testing, the switch was released then the EUT automatically deactivated. 6.4 Environmental Conditions Temperature: 20° C Relative Humidity: 52% ATM Pressure: 1011 mbar 6.5 Summary of Test Results/Plots Test Frequency Transmission Time Limit Transmission Type Result MHz seconds s Manually 314.8125 0.100 5 Pass Please refer to the attached plots. REPORT NO.: STR15058166I PAGE 15 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 Transmission Time REPORT NO.: STR15058166I PAGE 16 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 7. Duty Cycle 7.1 Standard Applicable According to FCC Part 15.231 (b)(2) and 15.35 (c), For pulse operation transmitter, the averaging pulsed emissions are calculated by peak value of measured emission plus duty cycle factor. 7.2 Test Equipment List and Details Description Manufacturer Model Serial Number Cal. Date Due. Date Spectrum Analyzer Agilent E4402B US41192821 2015-05-28 2016-05-27 Attenuator ATTEN ATS100-4-20 / 2015-05-28 2016-05-27 7.3 Test Procedure With the EUT’s antenna attached, the EUT’s output signal was received by the test antenna, which was connected to the spectrum analyzer. Set the center frequency to 314.8125MHz, than set the spectrum analyzer to Zero Span for the release time reading. During the testing, the switch was released then the EUT automatically deactivated. 7.4 Environmental Conditions Temperature: 20° C Relative Humidity: 52% ATM Pressure: 1011 mbar 7.5 Summary of Test Results/Plots Type of Pulse Width of Pulse Quantity of Pulse Transmission Time Total Time (Ton) ms ms ms Pulse 1 0.81 11 8.91 12.55 Pulse 2 0.26 14 3.64 Test Period (Tp) Total Time (Ton) Duty Cycle Duty Cycle Factor ms ms % dB 33.78 12.55 37.15 -8.60 Remark: Duty Cycle Factor=20*log(Duty Cycle) Please refer to the attached test plots REPORT NO.: STR15058166I PAGE 17 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 Quantity of Pulse REPORT NO.: STR15058166I PAGE 18 OF 19 FCC PART 15.231

JMA Alejandro Altuna S.L.U. Model: M-US1 Width of Pulse 1 and Pulse 2 ***** END OF REPORT ***** REPORT NO.: STR15058166I PAGE 19 OF 19 FCC PART 15.231


Document Created: 2015-07-13 13:42:24
Document Modified: 2015-07-13 13:42:24
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC