Test Report_DTS

FCC ID: 2AEUPBHASC042

Test Report

Download: PDF
FCCID_4206058

FCC&ISED Radio Test Report FCC ID: 2AEUPBHASC042 IC: 20271-BHASC042 This report concerns (check one): Original Grant Class I Change Class II Change Project No. : 1804T043C Equipment : Ring Test Model : Spotlight Cam-Battery Series Model : N/A Applicant : Ring, Inc. Address : 1523 26th St, Santa Monica, CA 90404,USA Date of Receipt : Oct. 23, 2018 Date of Test : Oct. 23, 2018 ~ Nov. 08, 2018 Issued Date : Nov. 09, 2018 Tested by : BTL Inc. Testing Engineer : (Kenji Lin) Technical Manager : (James Chiu) Authorized Signatory : (Andy Chiu) BTL INC. No.18, Ln. 171, Sec. 2, Jiuzong Rd., Neihu Dist., Taipei City, Taiwan (R.O.C.) TEL:+886-2-2657-3299 FAX: +886-2-2657-3331 Report No.: BTL-FICP-1-1804T043C Page 1 of 34 Report Version: R00

Declaration BTL represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with standards traceable to international standard(s) and/or national standard(s). BTL's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. BTL shall have no liability for any declarations, inferences or generalizations drawn by the client or others from BTL issued reports. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and ourselves, the test report shall not be reproduced, except in full, without our written approval. BTL’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. BTL is not responsible for the sampling stage, so the results only apply to the sample as received. The information, data and test plan are provided by manufacturer, so it is manufacturer’s responsibility to ensure that the apparatus meets the essential requirements in all the possible configurations as representative of its intended use. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Report No.: BTL-FICP-1-1804T043C Page 2 of 34 Report Version: R00

Table of Contents Page 1 . CERTIFICATION 5 2 . SUMMARY OF TEST RESULTS 6 2.1 TEST FACILITY 7 2.2 MEASUREMENT UNCERTAINTY 7 3 . GENERAL INFORMATION 8 3.1 GENERAL DESCRIPTION OF EUT 8 3.2 DESCRIPTION OF TEST MODES 9 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 9 3.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 10 3.5 DESCRIPTION OF SUPPORT UNITS 10 4 . EMC EMISSION TEST 11 4.1 RADIATED EMISSION MEASUREMENT 11 4.1.1 RADIATED EMISSION LIMITS 11 4.1.2 TEST PROCEDURE 12 4.1.3 DEVIATION FROM TEST STANDARD 12 4.1.4 TEST SETUP 13 4.1.5 EUT OPERATING CONDITIONS 14 4.1.6 EUT TEST CONDITIONS 14 4.1.7 TEST RESULTS (9KHZ TO 30MHZ) 14 4.1.8 TEST RESULTS (30MHZ TO 1000 MHZ) 14 4.1.9 TEST RESULTS (ABOVE 1000 MHZ) 14 5 . MAXIMUM PEAK CONDUCTED OUTPUT POWER TEST 15 5.1 APPLIED PROCEDURES / LIMIT 15 5.1.1 TEST PROCEDURE 15 5.1.2 DEVIATION FROM STANDARD 15 5.1.3 TEST SETUP 15 5.1.4 EUT OPERATION CONDITIONS 15 5.1.5 EUT TEST CONDITIONS 15 5.1.6 TEST RESULTS 15 6 . MEASUREMENT INSTRUMENTS LIST 16 7 . EUT TEST PHOTO 17 APPENDIX A - RADIATED EMISSION (9KHZ TO 30MHZ) 20 APPENDIX B - RADIATED EMISSION (30MHZ TO 1000MHZ) 25 APPENDIX C - RADIATED EMISSION (ABOVE 1000MHZ) 28 APPENDIX D - MAXIMUM PEAK CONDUCTED OUTPUT POWER 33 Report No.: BTL-FICP-1-1804T043C Page 3 of 34 Report Version: R00

REPORT ISSUED HISTORY Report Version Description Issued Date Original Issue. This is a supplementary report to the original test report (BTL-FICP-1-1804T043). The difference compared with original report is change bandpass R00 filter for WIESON Antenna. Nov. 09, 2018 Only Peak Output Power and Radiated Emissions (TX G MODE Low Channel) test need to be verified and the other original test data are kept in this report. Report No.: BTL-FICP-1-1804T043C Page 4 of 34 Report Version: R00

1. CERTIFICATION Equipment : Ring Brand Name : Test Model : Spotlight Cam-Battery Series Model : N/A Applicant : Ring, Inc. Manufacturer : Goldtek Technology CO.,LTD. Address : 16F., No166, Jian 1st Rd., Zhonghe Dist., New Taipei City 235, Taiwan (R.O.C.) Factory Goldtek Technology CO.,LTD. Address 16F., No166, Jian 1st Rd., Zhonghe Dist., New Taipei City 235, Taiwan (R.O.C.) Date of Test : Oct. 23, 2018 ~ Nov. 08, 2018 Test Sample : Engineering Sample Standard(s) : FCC Part15, Subpart C:(15.247) / ANSI C63.10-2013 RSS-247 Issue 2, Feb. 2017 RSS-GEN Issue 5, Apr. 2018 The above equipment has been tested and found in compliance with the requirement of the relative standards by BTL Inc. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. BTL-FICP-1-1804T043C) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of TAF according to the ISO-17025 quality assessment standard and technical standard(s). Report No.: BTL-FICP-1-1804T043C Page 5 of 34 Report Version: R00

2. SUMMARY OF TEST RESULTS Test procedures according to the technical standard(s): Applied Standard(s): FCC Part15 (15.247) , Subpart C Canada RSS-247 Issue 2, Feb. 2017, RSS-GEN Issue 5, Apr. 2018 Standard(s) Section Test Item Judgment Remark FCC IC 15.247(b)(3) RSS-247 5.4 (d) Peak Output Power PASS ------ 15.247(d)/ Transmitter Radiated 15.205/ RSS-247 5.5 PASS ------ 15.209 Emissions NOTE: (1)” N/A” denotes test is not applicable in this test report. (2) Input power is supplied by battery. Report No.: BTL-FICP-1-1804T043C Page 6 of 34 Report Version: R00

y BeSprile * 3UTL Bmd & % 2 2.1 TEST FACILITY The test facilities used to collect the test data in this report: Radiated emission Test (Below 1 GHz): CB15: (FCC RN:674415; FCC DN:TWO659; ISED Assigned Code:20088—5) No. 68—1, Ln. 169, Sec. 2, Datong Rd., Xizhi Dist., New Taipei City 221, Taiwan (R.O.C.) Radiated emission Test (Above 1 GHz): CB15: (FCC RN:674415; FCC DN:TWO659; ISED Assigned Code:20088—5) No. 68—1, Ln. 169, Sec. 2, Datong Rd., Xizhi Dist., New Taipei City 221, Taiwan (R.O.C.) 2.2 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16—4—2. The BTL measurement uncertainty is less than the CISPR 16—4—2 Usisp, requirement. The reported uncertainty of measurement y + U, where expanded uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of contfidence of approximately 95 %. A. Radiated emission test: Test Site Method Measurement Frequency Range U,(dB) CB15 9kHz ~ 150kHz 2.82 (3m) CISPR 150kHz ~ 3OMHz 258 Test Site |_Method Measurement Frequency Range Ant. |U,(dB) 3OMHz ~ 200MHz V 4.20 CB15 ciSPR 30MHz ~ 200MHz H_| 3.64 (3m) 200MHz ~ 1,000MHz V_| 4.56 200MHz ~ 1,000MHz H 3.90 Test Site |_Method Measurement Frequency Range Ant. |U,(dB) 1GHz ~ 6GHz V 4.46 Ton) cser sone—isene imE 6GHz ~18GHz H_| 4.00 Test Site Method Measurement Frequency Range U,(dB) i oser Bes —40 onz si2 Our calculated Measurement Instrumentation Uncertainty is shown in the tables above. These are our Uigp values in CISPR 16—4—2 terminology. Since Table 1 of CISPR 16—4—2 has values of measurement instrumentation uncertainty, called Uciser, as follows: Conducted Disturbance (mains port) — 150 kHz — 30 MHz: —3.6 dB Radiated Disturbance (electric field strength on an open area test site or alternative test site) — 30 MHz — 1000 MHz: 5.2 dB It can be seen that our Uvalues are smaller than Uciger. Note: unless specifically mentioned, the uncertainty of measurement has not been taken into account to declare the compliance or non—compliance to the specification. Report No.: BTL—FICP—1—18041T043C Page 7 of 34 Report Version: ROO

& y BeSprile 3UTL 5 mR 8y % 3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT Equipment Ring Brand Name rl n g Test Model Spotlight Cam—Battery Series Model N/A Model Difference N/A Battery supplied. Power Source (Battery is charged independently by USB power supply) Battery charge input: DC 5V Power Rating (1) Battery output: DC 3.65V 6040mAh 22.046Wh 2 * Battery Products Covered 1 * USB Cable Operation Frequency 2412~2462 MHz 802.11b:DSSS Modulation Technology 802.11g:OFDM 802.11n:OFDM 802.11b: 11/5.5/2/1 Mbps Bit Rate of Transmitter 802.11g: 54/48/36/24/18/12/9/6 Mbps 802.11n up to 72.2 Mbps 802.11b: 14.81dBm Output Power (Max.) 802.11g: 19.27dBm 802.11n(20MHz): 19.14dBm Note: 1. For a more detailed features description, please refer to the manufacturer‘s specifications or the user‘s manual. 2. Channel List: CHO1 — CH11 for 802.11b, 802.11g, 802.11n(20MHz) Frequency Frequency Frequency Frequency Channel (MHz) Channel (MHz) Channel (MH2) Channel (MHz) 01 2412 04 2427 07 2442 10 2457 02 2417 05 2432 08 2447 11 2462 03 2422 06 2437 09 2452 3. Table for Filed Antenna: Ant. Manufacturer Model Name Antenna Type Connector Gain (dBi) 1 WIESON N/A Dipole Antenna —PEX 1.08 Report No.: BTL—FICP—1—1804170430 Page 8 of 34 Report Version: ROO

3.2 DESCRIPTION OF TEST MODES The test system was pre-tested based on the consideration of all possible combinations of EUT operation mode. Following mode(s) as (were) found to be the worst case(s) and selected for the final test. Test Items Test mode Channel Note Transmitter Radiated Emissions TX G MODE 01 - (BELOW 1GHz) Transmitter Radiated Emissions TX G MODE 01 - (ABOVE 1GHz) TX B MODE 01/06/11 - Peak Output Power TX G MODE 01/06/11 - TX N-20M MODE 01/06/11 - Note: (1) The measurements are performed at the high, middle, low available channels. (2) 802.11b mode: DBPSK (1Mbps) 802.11g mode: OFDM (6Mbps) 802.11n HT20 mode : BPSK (MCS 0) For radiated emission tests, the highest output powers were set for final test. 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING During testing, channel & power controlling software provided by the customer was used to control the operating channel as well as the output power level. The RF output power selection is for the setting of RF output power expected by the customer and is going to be fixed on the firmware of the final end product power parameters of WLAN Test software version 1.0.2.0 Frequency (MHz) 2412 2437 2462 802.11b 6 6 2 802.11g 0 3 0 802.11n (20MHz) 5 6 0 Report No.: BTL-FICP-1-1804T043C Page 9 of 34 Report Version: R00

& y B Spmiie 3UTL nssm ? 2 3.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED EUT 3.5 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Mfr/Brand Model/Type No. FCC ID Series No. Item Shielded Type Ferrite Core Length Note Report No.: BTL—FICP—1—180417043C Page 10 of 34 Report Version: ROO

4. EMC EMISSION TEST 4.1 RADIATED EMISSION MEASUREMENT 4.1.1 RADIATED EMISSION LIMITS In case the emission fall within the restricted band specified on 15.205(a) & RSS-247 5.5, then the 15.209(a) & RSS-Gen limit in the table below has to be followed. LIMITS OF RADIATED EMISSION MEASUREMENT (9KHz-1000MHz) Frequency Field Strength Measurement Distance (MHz) (microvolts/meter) (meters) 0.009~0.490 2400/F(KHz) 300 0.490~1.705 24000/F(KHz) 30 1.705~30.0 30 30 30~88 100 3 88~216 150 3 216~960 200 3 960~1000 500 3 LIMITS OF RADIATED EMISSION MEASUREMENT (Above 1000MHz) (dBuV/m) (at 3 meters) Frequency (MHz) PEAK AVERAGE Above 1000 74 54 Notes: (1) The limit for radiated test was performed according to FCC PART 15C/RSS-247. (2) The tighter limit applies at the band edges. (3) Emission level (dBuV/m)=20log Emission level (uV/m). (4) The test result calculated as following: Measurement Value = Reading Level + Correct Factor Correct Factor = Antenna Factor + Cable Loss - Amplifier Gain(if use) Margin Level = Measurement Value - Limit Value Report No.: BTL-FICP-1-1804T043C Page 11 of 34 Report Version: R00

Spectrum Parameter Setting Attenuation Auto Start Frequency 1000 MHz Stop Frequency 10th carrier harmonic RBW / VBW 1MHz / 3MHz for Peak, (Emission in restricted band) 1MHz / 1/T for Average Receiver Parameter Setting Attenuation Auto Start ~ Stop Frequency 9KHz~90KHz for PK/AVG detector Start ~ Stop Frequency 90KHz~110KHz for QP detector Start ~ Stop Frequency 110KHz~490KHz for PK/AVG detector Start ~ Stop Frequency 490KHz~30MHz for QP detector Start ~ Stop Frequency 30MHz~1000MHz for QP detector 4.1.2 TEST PROCEDURE a. The measuring distance of 3 m shall be used for measurements. The EUT was placed on the top of a rotating table 0.8 meter above the ground at a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation.(below 1GHz) b. The measuring distance of 3 m shall be used for measurements. The EUT was placed on the top of a rotating table 1.5 meter above the ground at a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of the highest radiation.(above 1GHz) c. The height of the equipment or of the substitution antenna shall be 0.8m or 1.5m; the height of the test antenna shall vary between 1 m to 4 m. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights find the maximum reading (used Bore sight function). e. The receiver system was set to peak and average detect function and specified bandwidth with maximum hold mode when the test frequency is above 1GHz. f. The initial step in collecting radiated emission data is a receiver peak detector mode pre-scanning the measurement frequency range. Significant peaks are then marked and then Quasi Peak detector mode re-measured. g. All readings are Peak unless otherwise stated QP in column of Note. Peak denotes that the Peak reading compliance with the QP Limits and then QP Mode measurement didn‘t perform. (below 1GHz) h. All readings are Peak Mode value unless otherwise stated AVG in column of Note. If the Peak Mode Measured value compliance with the Peak Limits and lower than AVG Limits, the EUT shall be deemed to meet both Peak & AVG Limits and then only Peak Mode was measured, but AVG Mode didn‘t perform. (above 1GHz) i. For the actual test configuration, please refer to the related Item –EUT Test Photos. 4.1.3 DEVIATION FROM TEST STANDARD No deviation Report No.: BTL-FICP-1-1804T043C Page 12 of 34 Report Version: R00

4.1.4 TEST SETUP (A) Radiated Emission Test Set-Up Frequency Below 1 GHz Absorbers 1-4 m 3m EUT 1m 0.8 m Ground Plane Receiver Amp. (B) Radiated Emission Test Set-Up Frequency Above 1 GHz Band edge Absorbers 1-4 m 3m EUT 0.7 m 0.8 m 1m Absorbers 0.3 m Ground Plane Receiver Amp. Report No.: BTL-FICP-1-1804T043C Page 13 of 34 Report Version: R00

(C) For Radiated Emissions Below 30MHz 4.1.5 EUT OPERATING CONDITIONS The EUT was programmed to be in continuously transmitting mode. 4.1.6 EUT TEST CONDITIONS Temperature: 25°C Relative Humidity: 55% Test Voltage: DC 3.6V 4.1.7 TEST RESULTS (9KHZ TO 30MHZ) Please refer to the Appendix A. Remark: (1) The amplitude of spurious emissions which are attenuated by more than 20 dB below the permissible value has no need to be reported. (2) Distance extrapolation factor = 40 log (specific distance / test distance) (dB). (3) Limit line = specific limits (dBuV) + distance extrapolation factor. 4.1.8 TEST RESULTS (30MHZ TO 1000 MHZ) Please refer to the Appendix B. 4.1.9 TEST RESULTS (ABOVE 1000 MHZ) Please refer to the Appendix C. Remark: (1) No limit: This is fundamental signal, the judgment is not applicable. For fundamental signal judgment was referred to Peak output test. Report No.: BTL-FICP-1-1804T043C Page 14 of 34 Report Version: R00

5. MAXIMUM PEAK CONDUCTED OUTPUT POWER TEST 5.1 APPLIED PROCEDURES / LIMIT FCC Part15 (15.247) , Subpart C/ RSS-247 Frequency Range Section Test Item Limit Result (MHz) 15.247(b)(3) Maximum Output 1 Watt or 30dBm 2400-2483.5 PASS RSS-247 5.4 (d) Power 5.1.1 TEST PROCEDURE a. The EUT was directly connected to the power meter and antenna output port as show in the block diagram below, b. The maximum peak conducted output power was performed in accordance with method 9.1.2 of FCC KDB 558074 D01 DTS Meas Guidance. 5.1.2 DEVIATION FROM STANDARD No deviation. 5.1.3 TEST SETUP 5.1.4 EUT OPERATION CONDITIONS The EUT was programmed to be in continuously transmitting mode. 5.1.5 EUT TEST CONDITIONS Temperature: 25°C Relative Humidity: 55% Test Voltage: DC 3.6V 5.1.6 TEST RESULTS Please refer to the Appendix D. Report No.: BTL-FICP-1-1804T043C Page 15 of 34 Report Version: R00

6. MEASUREMENT INSTRUMENTS LIST Radiated Emission Measurement Item Kind of Equipment Manufacturer Type No. Serial No. Calibrated until 1 Preamplifier EMCI 012645B 980267 Apr. 14, 2019 2 Preamplifier EMCI EMC02325 980217 Apr. 14, 2019 3 Preamplifier EMCI EMC2654045 980030 Apr. 14, 2019 EMC104-SM-S 4 Test Cable EMCI 8m Apr. 14, 2019 M-8000 EMC104-SM-S 5 Test Cable EMCI 150207 Apr. 14, 2019 M-800 EEMC104-SM-S 6 Test Cable EMCI 151205 Apr. 14, 2019 M-3000 MY5542012 7 MXE EMI Receiver Agilent N9038A Jan. 27, 2019 7 MY5222099 8 Signal Analyzer Agilent N9010A May 22, 2019 0 9 Loop Ant EMCI LPA600 274 May 03, 2019 10 Horn Ant SCHWARZBECK BBHA 9120D 9120D-1342 May 02, 2019 11 Horn Ant Schwarzbeck BBHA 9170 187 Aug. 16, 2019 Trilog-Broadband 12 Schwarzbeck VULB 9168 9168-548 Mar. 22, 2019 Antenna 13 5dB Attenuator EMCI EMCI-N-6-05 AT-N0623 Mar. 22, 2019 Peak Output Power Measurement Item Kind of Equipment Manufacturer Type No. Serial No. Calibrated until 1 Power Meter Anritsu ML2495A 1128008 Aug. 15, 2019 2 Power Sensor Anritsu MA2411B 1126001 Aug. 15, 2019 Remark: ”N/A” denotes no model name, serial no. or calibration specified. All calibration period of equipment list is one year. Report No.: BTL-FICP-1-1804T043C Page 16 of 34 Report Version: R00

APPENDIX A - RADIATED EMISSION (9KHZ TO 30MHZ) Report No.: BTL-FICP-1-1804T043C Page 20 of 34 Report Version: R00

Test Mode: TX G MODE 2412MHz Ant 90° Report No.: BTL-FICP-1-1804T043C Page 21 of 34 Report Version: R00

Test Mode: TX G MODE 2412MHz Ant 90° Report No.: BTL-FICP-1-1804T043C Page 22 of 34 Report Version: R00

Test Mode: TX G MODE 2412MHz Ant 0° Report No.: BTL-FICP-1-1804T043C Page 23 of 34 Report Version: R00

Test Mode: TX G MODE 2412MHz Ant 0° Report No.: BTL-FICP-1-1804T043C Page 24 of 34 Report Version: R00

APPENDIX B - RADIATED EMISSION (30MHZ TO 1000MHZ) Report No.: BTL-FICP-1-1804T043C Page 25 of 34 Report Version: R00

Test Mode TX G MODE 2412MHz Polarization Vertical Report No.: BTL-FICP-1-1804T043C Page 26 of 34 Report Version: R00

Test Mode TX G MODE 2412MHz Polarization Horizontal Report No.: BTL-FICP-1-1804T043C Page 27 of 34 Report Version: R00

APPENDIX C - RADIATED EMISSION (ABOVE 1000MHZ) Report No.: BTL-FICP-1-1804T043C Page 28 of 34 Report Version: R00

Test Mode TX G MODE _2412 MHz Polarization Vertical Report No.: BTL-FICP-1-1804T043C Page 29 of 34 Report Version: R00

Test Mode TX G MODE _2412 MHz Polarization Vertical Report No.: BTL-FICP-1-1804T043C Page 30 of 34 Report Version: R00

Test Mode TX G MODE _2412 MHz Polarization Horizontal Report No.: BTL-FICP-1-1804T043C Page 31 of 34 Report Version: R00

Test Mode TX G MODE _2412 MHz Polarization Horizontal Report No.: BTL-FICP-1-1804T043C Page 32 of 34 Report Version: R00

APPENDIX D - MAXIMUM PEAK CONDUCTED OUTPUT POWER Report No.: BTL-FICP-1-1804T043C Page 33 of 34 Report Version: R00

Test Mode :TX B Mode_CH01/06/11 Frequency Conducted Conducted Max. Limit Max. Limit Result (MHz) Power (dBm) Power (W) (dBm) (W) 2412 14.28 0.0268 30.00 1.00 Complies 2437 14.24 0.0265 30.00 1.00 Complies 2462 14.81 0.0303 30.00 1.00 Complies Test Mode :TX G Mode_CH01/06/11 Frequency Conducted Conducted Max. Limit Max. Limit Result (MHz) Power (dBm) Power (W) (dBm) (W) 2412 19.27 0.0845 30.00 1.00 Complies 2437 19.20 0.0832 30.00 1.00 Complies 2462 19.12 0.0817 30.00 1.00 Complies Test Mode :TX N20 Mode_CH01/06/11 Frequency Conducted Conducted Max. Limit Max. Limit Result (MHz) Power (dBm) Power (W) (dBm) (W) 2412 16.90 0.0490 30.00 1.00 Complies 2437 17.06 0.0508 30.00 1.00 Complies 2462 19.14 0.0820 30.00 1.00 Complies End of Test Report Report No.: BTL-FICP-1-1804T043C Page 34 of 34 Report Version: R00


Document Created: 2019-03-07 15:37:07
Document Modified: 2019-03-07 15:37:07
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC