5LP1Y8_User Manual_REV1

FCC ID: 2AEUPBHAPB001

Users Manual

Download: PDF
FCCID_4125218

108mm Beams Spotlight 90mm 02_Spotlight_MANUAL.indd 1 9/28/18 4:19 PM

1. Set up your Spotlight. Set up your Ring Beams Bridge. The Bridge connects your Ring Beams lights to the rest of your Ring system. To set up your Bridge, follow the instructions in the Ring app or Bridge user manual. Download the Ring app. The app walks you through setting up and managing your Spotlight. If you do not own a Bridge, don’t Search for “Ring” in one of these app worry. Your Spotlight will work fine, but you won’t be able to stores, or visit: ring.com/app control it in the app. Download from Windows Store 2 3 02_Spotlight_MANUAL.indd 3 9/28/18 4:19 PM

Insert the batteries. Set up your Spotlight in the Ring app. Twist and pull off In the app, tap Doorbells the front of the light, Set Up a Device. Security Cams then press the side Chimes buttons on the battery When prompted, Beams compartment to open. select Beams and Alarm follow the in-app instructions. Insert four D-Cell batteries, then slide the battery cover back onto your Spotlight. 4 5 02_Spotlight_MANUAL.indd 5 9/28/18 4:19 PM

2. Install your Spotlight. Hold the base against the surface and drive the three mounting screws. Loosen the locking Insert your Spotlight screw on the base into the base at your and remove the base chosen angle and from your Spotlight. tighten the screw. Use the base as a Loosen the side template to mark the screw on your screw holes. Spotlight, rotate to Your Spotlight detects motion desired angle, and best when mounted 8-12 feet above the ground. tighten the screw. 6 7 02_Spotlight_MANUAL.indd 7 9/28/18 4:19 PM

For additional help, visit: ring.com/help Or give us a call… US 1 800 656 1918 Canada 1 855 300 7289 Worldwide +1 310 929 7085 For a list of all our customer support numbers, visit: ring.com/callus To review your warranty coverage, please visit www.ring.com/warranty. Patents: www.ring.com/patents © 2018 Ring LLC or its affiliates. RING, ALWAYS HOME, and all related logos are trademarks of Ring LLC or its affiliates. Last updated: 09/28/18 02_Spotlight_MANUAL.indd 8 9/28/18 4:19 PM

Warnings This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason- able protection against harmful interference in a residential This device complies with part 15 of the FCC Rules and installation. This equipment generates, uses and can Industry Canada licence-exempt RSS standard(s). Opera- radiate radio frequency energy and, if not installed and tion is subject to the following two conditions: (1) this used in accordance with the instructions, may cause device may not cause interference, and (2) this device must harmful interference to radio communications. However, accept any interference, including interference that may there is no guarantee that interference will not occur in a cause undesired operation of the device. particular installation. If this equipment does cause harmful Le présent appareil est conforme aux CNR d'Industrie interference to radio or television reception, which can be Canada applicables aux appareils radio exempts de determined by turning the equipment off and on, the user licence. L'exploitation est autorisée aux deux conditions is encouraged to try to correct the suivantes : (1) l'appareil ne doit pas produire de brouillage, interference by one or more of the following measures: et (2) l'utilisateur de l'appareil doit accepter tout brouillage • Reorient or relocate the receiving antenna. radioélectrique subi, même si le brouillage est susceptible • Increase the separation between the equipment and d'en compromettre le fonctionnement. receiver. • Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected. de moin de 20 cm. Installer les antennes de facon à ce que • Consult the dealer or an experienced radio/TV technician le personnel ne puisse approcher à 20 cm ou moins de la for help. position centrale de l’ antenne. Caution: Any changes or modifications to this device not La FCC des éltats-unis stipule que cet appareil doit être en explicitly approved by manufacturer could void your tout temps éloigné d’au moins 20 cm des personnes authority to operate this equipment. pendant son functionnement. MPE Reminding To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance


Document Created: 2018-12-31 10:00:55
Document Modified: 2018-12-31 10:00:55
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC