FCC Modular Approval Request

FCC ID: 2AEMI-PHOTON

Cover Letter(s)

Download: PDF
FCCID_2659051

! Modular Approval Request FCC (per DA 00-1407)! Company!name:!Spark!Labs,!Inc.,! Address:!320!Alabama!St!#2!San!Francisco,!CA!94110,!San!Francisco,!California,!! !!!!!!!!!!!!!!!!!United!States! FCC!ID 2AEMIDPHOTON! Items to be covered Answer from applicant 1.! The modular transmitter must have its own RF shielding. YES, Please refer to External Photos. 2.! The modular transmitter must have buffered modulation/data inputs (if such inputs are YES, U1 STM32F205RGY6 is provided) to ensure that the module will comply with Part 15 requirements under conditions used for the function. of excessive data rates or over-modulation. 3.! The modular transmitter must have its own power supply regulation. YES, U2 RT8008-33GB is used for the power supply regulation. 4.! The modular transmitter must comply with the antenna requirements of Section 15.203 and YES, it is Chip antenna. 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable).. 5.! The modular transmitter must be tested in a stand-alone configuration, i.e., the module must YES, The EUT is tested in a not be inside another device during testing. This is intended to demonstrate that the module stand-alone configuration as the is capable of complying with Part 15 emission limits regardless of the device into which it is test photos show. eventually installed. 6.! The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is YES, please refer to the not visible when the module is installed inside another device, then the outside of the device exhibition label sample for this into which the module is installed must also display a label referring to the enclosed module. module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: 2AEMI-PHOTON” or “Contains FCC ID: 2AEMI-PHOTON.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7.! The modular transmitter must comply with any specific rule or operating requirements YES, please refer to the user applicable to the transmitter and the manufacturer must provide adequate instructions along manual. with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF exposure requirements. For YES, RF exposure statement is example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including attached in the user manual. 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be possible to obtain a “Limited Modular Approval” (LMA). ( 5- 5 2 5: :1 2 - 5: :2 1) : )205 :


Document Created: 0640-10-01 00:00:00
Document Modified: 0640-10-01 00:00:00
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC