User Manual

FCC ID: 2AEB4ALT01

Users Manual

Download: PDF
FCCID_3600793

User Manual AR-4LH Vehicle Tracking Device The information presented in this document is strictly confidential and contains trade secrets and other confidential information that are the exclusive property of Connected Holdings Author Revision Changes Date Tony_Wang V01 Initial version 2017-08-27 © 2017 Connected Holdings LLC 1/ 9

Contents 1 Introduction 3 2 Hardware Design 4 2.1 Basic Hardware 4 2.2 Basic RF Performance 5 2.3 Certification and Safety 6 4 Test Method 7 4.1 Hardware 7 4.2 Software Test 7 Mechanical Structure(mm) 8 FCC Statement 9 IC STATEMENT 9 © 2017 Connected Holdings LLC 2/ 9

1 Introduction The Arrow-L is a self-Contained vehicle tracking device that combines GPS location with WCDMA/LTE connectivity. The Arrow-L appears to a user or a server application as a single endpoint device. It can be queried, updated and configured either through a serial connection, or an over the air LTE or WCDMA IP connection, or through SMS messaging. The Arrow-L presents itself over these connections as an enhanced cellular modem with attached functional elements. These elements include:  GPS location engine  General Purpose Bidirectional I/O (GPIO) pins  Relay drive pin output  Serial UART port  Input voltage monitor (optional)  Watchdog lockup protection Access to these elements and general purpose interfaces is done through an extended AT command set as defined herein. Application scene: This product will be designed based on the MDM9207-1 baseband chipset, which includes LTE Cat.1, WCDMA, and GPS functionality. The device will use one multi-band antenna and one dedicated GPS antenna. © 2017 Connected Holdings LLC 3/ 9

2 Hardware Design 2.1 Basic Hardware Items Requirement Baseband Chipset MDM9207-1 RF Transceiver WTR2965 Memory MCP_NAND 2Gb / mobile DDR2 1Gb Air Interface Support for WCDMA and LTE Cat.1 Frequency 4G band support : Band2/4/12 3G band support : Band2/5 Antenna Internal Antenna GPS Antenna Dedicated high performance ceramic antenna Interface UART TX UART RX 12V DC Input（1A current） Relay Drive GPIO1 GPIO2 Battery Monitor internal analog input scaled (Optional) Watchdog Supported Motion Detect Sensor LED 2 LED Supported 2 LEDs(one is RED，one is Green) Battery Built in battery（80MAH Lion） Working Time 4 hours Power Cable connector type 8 pin Power Consumption < 5Watts The Arrow-L provides support for specialized hardware features through extended AT commands. The features supported include the following. GPS The major functionality of the GPS system is to compute the correlation results between the incoming signal and the selected PRN code based on certain Carrier Doppler Frequency, Code Doppler Frequency, code phase, carrier phase, and the particular satellite the system is tracking or acquiring. GPIO The GPIO pins are presented to the external environment on the main connector. They are general purpose bidirectional lines capable of providing system interrupts to generate a report or drive logic levels to external devices. These lines are 2.8V logic level and are 16V tolerant. © 2017 Connected Holdings LLC 4/ 9

LED’s Two LED status indicators are provided to verify correct installation and operation. UART A UART port is provided for AT command and data interaction and optionally for application specific control. Relay Driver A 500mA sink capable output pin is provided. This pin is meant to drive a relay coil intended to interrupt the starter solenoid relay for the ignition circuit to a car. Battery Monitor The battery monitor is internal analog input scaled such that the DC value of the power input pin to the Arrow-L system is measured. Watchdog MDM9207-1 chipset provide internal software and hardware Watchdog. Motion Detect This function will work with firmware power down options to keep the Arrow-L in a very low power down state until motion is detected. Upon wakening, a report can then be generated. 2.2 Basic RF Performance Items Requirements Remark TRP free space CTIA TRP free space TIS free space CTIA TIS free space Board RF Specification 3G WCDMA Band Band2 / Band5 Rx Spec Follow TS 34.121 Ch.6 Tx Spec Follow TS 34.121 Ch.5 4G LTE Cat.1 Band Band2 / Band4 / Band12 Rx Spec Follow TS 36.521 Ch.7 Tx Spec Follow TS 36.521 Ch.6 GPS L1-band (1.57542GHz) Frequency Support Channels: 210 PRN， 66 Search， 22 Simultaneous tracking Sensitivity (UHIS): Sensitivity Tracking: -156dBm © 2017 Connected Holdings LLC 5/ 9

Reacquisition: -153dBm Acquisition: -144dBm Acquisition time: Hot: <2s Tracking Time Requirement Warm: <15s Cold: <60s Reacquisition: 2s - 10s Depends on signal level 2.3 Certification and Safety Items Requirement Drop Design 0.8meter 6 direction standard drop test Temperature Range -20 to 40°C Operation -40 to +85°C Storage Humidity: 20% to 90% Operation 10% to 95% Storage Altitude: -500 to +18,000m FCC Certification FCC 47 CFR Part 15 and Part 18 Safety UL Listing ESD Requirement 8KV non-Conductive © 2017 Connected Holdings LLC 6/ 9

3 Test Method 3.1 Hardware Test Item Description Baseband Function Test • Power Input Test • Power Consumption and Current Test • Heat Dissipation Test • UART Stability Test • GPIO Level Test • LED Stability Test • Drop Down Test • ESD Test • High/Low Temperature Test RF Test • RF Performance Test • GPS Performance Test • Antenna Performance Test 3.2 Software Test Test Environment Construct  Message Test environment 1. USB dongle and PC as message server 2. Send message to Arrow-L  UART Test environment 1. Connect Arrow-L to pc with com serial cable 2. Open Terminal tool and send at command 3. Response can be shown at terminal window © 2017 Connected Holdings LLC 7/ 9

Mechanical Structure(mm) © 2017 Connected Holdings LLC 8/ 9

FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. IC STATEMENT This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. © 2017 Connected Holdings LLC 9/ 9


Document Created: 2017-09-29 17:47:45
Document Modified: 2017-09-29 17:47:45
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC