User Manual

FCC ID: 2AE6GVHF-01

Users Manual

Download: PDF
FCCID_2692038

VHF WIRELESS Receiver VHF-01 FCC ID:2AE6GVHF-01 USER’S MANUAL PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATION

SPECIFICATIONS RECEIVER Receiver Parts Description Frequency Range: 177.6MHz or 186.6MHz or 198.6MHz or 204.6MHz Frequency Stability: 10PPM Sensitivity: -92dBm Frequency Response: 80Hz~12KHz Single Audio Output Level: 150mV(RMS) Front Channel S/N: >75dB Distortion: <1% 1 2 3 4 Power Supply: DC 9V 200mA Current Consumption: 150mA Rear Transmitter 5 6 7 Frequency Range: 177.6MHz or 186.6MHz or 198.6MHz or 204.6MHz Frequency Stability: 10ppm RF Output: <10mW Modulation: FM Max Deviation: ±75KHz 1. Power Indicator 5. 1/4" unbalanced output jack Harmonic Suppression : >45dB 2. ON/OFF Switch 6. DC input jack Power Supply: 3V(2xAA batteries) 3. Volume Control 7. Antenna Current Consumption: 100mA 4. RF Indicator Operation 1. Connect one end of supplied 6.35mm to 6.35mm plug audio cable into AF OUT jack on rear panel of the receiver. Connect the other end of the audio cable into "MIC IN" or "AUX IN" of amplifier or mixer. 2. Connect DC plug of supplied AC/DC adapter to DC INPUT jack on rear panel of the receiver. Connect AC plug of AC/DC adapter to mains power socket. 3. Press ON/OFF button on front panel to turn on the receiver. 4. Extend antenna fully. 5. Turn on the transmitter. RF indicator on receiver will light. 6. Adjust receiver volume and your amplifier or mixer volume to suitable level.

HANDHELD MIC BELT PACK TRANSMITTER Parts Description Parts Description 1 2 3 1. Grille(Capsule inside) 1 1. Power ON/OFF/MUTE Switch 2. Power/low battery Indicator 2. Power/low battery Indicator 3. Power ON/OFF/MUTE Switch 3. MIC in jack 4. Battery Compartment/Cover 4. Battery Compartment/Cover 2 3 4 4 Operation 1. Open battery cover. Install the provided 2pcs 1.5V AA batteries and then close the cover. Pay attention to the correct polarity. 2. Push power switch to ON position, power indicator should flash once briefly indicating that the transmitter has sufficient power. If Operation the power LED indicator stays on, it indicates that the battery has insufficient power and should be changed. If the power LED 1. Open battery cover. Install the provided 2pcs 1.5V AA batteries and indicator does not light at all and the transmitter does not work, it then close the cover. Pay attention to the correct polarity. indicates the battery is dead and you should change the battery. 2. Insert headset MIC or clip-on MIC plug into MIC IN jack. And turn 3. Now receiver RF indicator should light(Please confirm frequency of plug clockwise to lock the headset MIC. microphone same as that of receiver before operation). 3. Slide power switch to ON position, power indicator should flash 4. Push power switch to MUTE position to mute the sound. once briefly indicating that the transmitter has sufficient power. If 5. During operation if power indicator lights red, this indicates the the power LED indicator stays on, it indicates that the battery has battery is Iow. Please replace new battery. insufficient power and should be changed. If the power LED 6. If the microphone is not going to be used for any length of time, indicator does not light at all and the transmitter does not work, it push power switch to OFF position and remove the battery. indicates the battery is dead and you should change the battery. 4. Now receiver RF indicator should light. Please confirm frequency of transmitter is same as receiver before operation. 5. Slide power switch to MUTE position to mute the sound. 6. If the transmitter is not going to be used for any length of time, push the power switch to OFF position and remove the battery.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.


Document Created: 2015-07-20 10:17:04
Document Modified: 2015-07-20 10:17:04
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC