MPE Report

FCC ID: 2ADZRG240WE

RF Exposure Info

Download: PDF
FCCID_3934534

MPE TEST REPORT Applicant NOKIA Shanghai Bell CO. Ltd. FCC ID 2ADZRG240WE Product GPON ONU Model G-240W-E Report No. R1804B0034-M1 Issue Date June 21, 2018 TA Technology (Shanghai) Co., Ltd. tested the above equipment in accordance with the requirements in FCC 47 CFR Part 1 1.1310. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Performed by: Jiangpeng Lan Approved by: Kai Xu TA Technology (Shanghai) Co., Ltd. No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai, China TEL: +86-021-50791141/2/3 FAX: +86-021-50791141/2/3-8000

MPE Test Report Report No: R1804B0034-M1 Table of Contents 1 Test Laboratory............................................................................................................................... 3 1.1 Notes of the Test Report ......................................................................................................... 3 1.2 Test facility .............................................................................................................................. 3 1.3 Testing Location ...................................................................................................................... 4 1.4 Laboratory Environment .......................................................................................................... 4 2 Description of Equipment under Test .............................................................................................. 5 3 Maximum conducted output power (measured) and antenna Gain ................................................ 6 TA Technology (Shanghai) Co., Ltd. Page 2 of 9 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

MPE Test Report Report No: R1804B0034-M1 1 Test Laboratory 1.1 Notes of the Test Report This report shall not be reproduced in full or partial, without the written approval of TA technology (shanghai) co., Ltd.The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein .Measurement Uncertainties were not taken into account and are published for informational purposes only. This report is written to support regulatory compliance of the applicable standards stated above. 1.2 Test facility CNAS (accreditation number:L2264) TA Technology (Shanghai) Co., Ltd. has obtained the accreditation of China National Accreditation Service for Conformity Assessment (CNAS). FCC (Designation number: CN1179, Test Firm Registration Number: 446626) TA Technology (Shanghai) Co., Ltd. has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. IC (recognition number is 8510A) TA Technology (Shanghai) Co., Ltd. has been listed by industry Canada to perform electromagnetic emission measurement. VCCI (recognition number is C-4595, T-2154, R-4113, G-10766) TA Technology (Shanghai) Co., Ltd. has been listed by industry Japan to perform electromagnetic emission measurement. A2LA (Certificate Number: 3857.01) TA Technology (Shanghai) Co., Ltd. has been listed by American Association for Laboratory Accreditation to perform electromagnetic emission measurement. TA Technology (Shanghai) Co., Ltd. Page 3 of 9 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

MPE Test Report Report No: R1804B0034-M1 1.3 Testing Location Company: TA Technology (Shanghai) Co., Ltd. Address: No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai, China City: Shanghai Post code: 201201 Country: P. R. China Contact: Xu Kai Telephone: +86-021-50791141/2/3 Fax: +86-021-50791141/2/3-8000 Website: http://www.ta-shanghai.com E-mail: xukai@ta-shanghai.com 1.4 Laboratory Environment Temperature Min. = 18C, Max. = 25 C Relative humidity Min. = 30%, Max. = 70% Ground system resistance < 0.5  Ambient noise is checked and found very low and in compliance with requirement of standards. Reflection of surrounding objects is minimized and in compliance with requirement of standards. TA Technology (Shanghai) Co., Ltd. Page 4 of 9 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

MPE Test Report Report No: R1804B0034-M1 2 Description of Equipment under Test Client Information Applicant Nokia Shanghai Bell CO., Ltd. 388#, Ningqiao Road, China (Shanghai) Pilot Free Trade Zone, Applicant address Shanghai 201206, China Manufacturer Nokia Shanghai Bell CO., Ltd. 388#, Ningqiao Road, China (Shanghai) Pilot Free Trade Zone, Manufacturer address Shanghai 201206, China General Technologies Model G-240W-E SN / Hardware Version Version C Software Version 3FE47344AFIB36 Date of Testing: June 10, 2018 ~ June 19, 2018 TA Technology (Shanghai) Co., Ltd. Page 5 of 9 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

MPE Test Report Report No: R1804B0034-M1 3 Maximum conducted output power (measured) and antenna Gain The numeric gain (G) of the antenna with a gain specified in dB is determined by Numeric gain (G)=10^(antenna gain/10) Maximum Conducted Output Antenna Gain Band Power Numeric gain (dBi) (dBm) (mW) WiFi 2.4G 28.42 695.02 3 2.00 WiFi 5G 29.12 816.58 4 2.51 TA Technology (Shanghai) Co., Ltd. Page 6 of 9 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

MPE Test Report Report No: R1804B0034-M1 According to section 1.1310 of FCC 47 CFR Part 1, limits for maximum permissible exposure (MPE) are as following Note1. Occupational/controlled limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when an individual is transient through a location where occupational / controlled limits apply provided he or she is made aware of the potential for exposure. Note2: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or can not exercise control over their exposure. TA Technology (Shanghai) Co., Ltd. Page 7 of 9 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

MPE Test Report Report No: R1804B0034-M1 The maximum permissible exposure for for 1500~100,000MHz is 1.0.So Band The maximum permissible exposure WiFi 2.4G 1.0mW/cm2 WiFi 5G 1.0mW/cm2 IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. No change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. TA Technology (Shanghai) Co., Ltd. Page 8 of 9 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.

MPE Test Report Report No: R1804B0034-M1 RF Exposure Calculations: The following information provides the minimum separation distance for the highest gain antenna provided. This calculation is based on the conducted power, considering maximum power and antenna gain. The formula shown in KDB 447498 D01 is used in the calculation. Equation from KDB 447498 D01 General RF Exposure Guidance v06 (10/23/2015) is: 2 S= PG / 4∏R 2 Where: S = power density (in appropriate units, e.g. mW/cm ) P = Time-average maximum tune up procedure (in appropriate units, e.g., mW) G = the numeric gain of the antenna R = distance to the center of radiation of the antenna (20 cm = limit for MPE) Test Result Limit Value The MPE Band PG (mW) 2 2 (mW/cm ) (mW/cm ) ratio WiFi 2.4G 1386.76 0.28 1.00 0.28 WiFi 5G 2051.16 0.41 1.00 0.41 Note: R = 20cm ∏= 3.1416 The MPE ratio = Mac Test Result÷Limit Value So the simultaneous transmitting antenna pairs as below: ∑of MPE ratios=WiFi 2.4G + WiFi 5G =0.28+0.41=0.69 <1 Note: For transmitters, minimum separation distance is 20cm, even if calculations indicate MPE distance is less. TA Technology (Shanghai) Co., Ltd. Page 9 of 9 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.


Document Created: 2018-06-21 18:31:43
Document Modified: 2018-06-21 18:31:43
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC