Test report

FCC ID: 2ADX6-7320

Test Report

Download: PDF
FCCID_2562434

Global United Technology Services Co., Ltd. Report No.: GTSE14110205302 FCC REPORT Applicant: Braeburn Systems LLC Address of Applicant: 2215 Cornell Avenue Montgomery, Illinois 60538 USA Equipment Under Test (EUT) Product Name: ELECTRONIC THERMOSTAT Model No.: 7320 FCC ID: 2ADX6-7320 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.249:2013 Date of sample receipt: January 30, 2015 Date of Test: February 02-05, 2015 Date of report issued: February 06, 2015 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Authorized Signature: Robinson Lo Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the GTS product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of GTS or testing done by GTS in connection with, distribution or use of the product described in this report must be approved by GTS in writing. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.

Report No.: GTSE14110205302 2 Version Version No. Date Description 00 February 06, 2015 Original Prepared By: Date: February 06, 2015 Project Engineer Check By: Date: February 06, 2015 Reviewer Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 20

Report No.: GTSE14110205302 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 VERSION .................................................................................................................................................. 2 3 CONTENTS .............................................................................................................................................. 3 4 TEST SUMMARY ..................................................................................................................................... 4 5 GENERAL INFORMATION ...................................................................................................................... 5 5.1 CLIENT INFORMATION ......................................................................................................................... 5 5.2 GENERAL DESCRIPTION OF EUT ......................................................................................................... 5 5.3 TEST MODE ........................................................................................................................................ 6 5.4 DESCRIPTION OF SUPPORT UNITS ....................................................................................................... 6 5.5 TEST FACILITY.................................................................................................................................... 6 5.6 TEST LOCATION ................................................................................................................................. 6 5.7 OTHER INFORMATION REQUESTED BY THE CUSTOMER ......................................................................... 6 6 TEST INSTRUMENTS LIST ..................................................................................................................... 7 7 TEST RESULTS AND MEASUREMENT DATA...................................................................................... 8 7.1 ANTENNA REQUIREMENT:.................................................................................................................... 8 7.2 CONDUCTED EMISSIONS ..................................................................................................................... 9 7.3 RADIATED EMISSION METHOD ........................................................................................................... 12 7.3.1 Field Strength of The Fundamental Signal ................................................................................ 14 7.3.2 Spurious emissions .................................................................................................................... 14 7.3.3 Bandedge emissions.................................................................................................................. 17 7.4 20DB OCCUPY BANDWIDTH .............................................................................................................. 18 8 TEST SETUP PHOTO ............................................................................................................................ 19 9 EUT CONSTRUCTIONAL DETAILS ..................................................................................................... 20 Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 20

Report No.: GTSE14110205302 4 Test Summary Test Item Section in CFR 47 Result Antenna requirement 15.203 Pass AC Power Line Conducted Emission 15.207 Pass Field strength of the fundamental signal 15.249 (a) Pass Spurious emissions 15.249 (a) (d)/15.209 Pass Band edge 15.249 (d)/15.205 Pass 20dB Occupied Bandwidth 15.215 (c) Pass Pass: The EUT complies with the essential requirements in the standard. Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 4 of 20

Report No.: GTSE14110205302 5 General Information 5.1 Client Information Applicant: Braeburn Systems LLC Address of Applicant: 2215 Cornell Avenue Montgomery, Illinois 60538 USA Manufacturer: Computime Limited Address of Manufacturer: 9/F, Tower One, Lippo Centre, 89 Queensway, Hong Kong Factory: Computime Electronics (shenzhen) Company Limited Address of Factory: Yuekenguangyu Industrial Park,Kangqiao Road 88#, Danzhutou Community, Nanwan Street Office Longgang District, Shenzhen, China 5.2 General Description of EUT Product Name: ELECTRONIC THERMOSTAT Model No.: 7320 Operation Frequency: 915MHz Modulation type: GFSK Antenna Type: Integral antenna Antenna gain: 0dBi Power supply: AC 24V Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 5 of 20

Report No.: GTSE14110205302 5.3 Test mode Transmitting mode Keep the EUT in continuously transmitting mode. Remark: During the test, the test voltage was tuned from 85% to 115% of the nominal rated supply voltage, and found that the worst case was under the nominal rated supply condition. So the report just shows that condition’s data. Per-test mode. We have verified the construction and function in typical operation, The EUT was placed on three different polar directions; i.e. X axis, Y axis, Z axis. which was shown in this test report and defined as follows: Axis X Y Z Field Strength(dBuV/m) 85.57 89.10 86.38 Final Test Mode: According to ANSI C63.4 standards, the test results are both the “worst case” and “worst setup”: Y axis (see the test setup photo) 5.4 Description of Support Units Manufacturer Description Model Serial Number FCC approval AC/AC Linear ET ETE40310F N/A Verification Transformer 5.5 Test Facility The test facility is recognized, certified, or accredited by the following organizations: ● CNAS —Registration No.: CNAS L5775 CNAS has accredited Global United Technology Services Co., Ltd. To ISO/IEC 17025 General Requirements for the competence of testing and calibration laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. ● FCC —Registration No.: 600491 Global United Technology Services Co., Ltd., Shenzhen EMC Laboratory has been registered and fuly described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in files. Registration 600491, June 28, 2013. ● Industry Canada (IC) —Registration No.: 9079A-2 The 3m Semi-anechoic chamber of Global United Technology Services Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 9079A-2, June 26, 2013. 5.6 Test Location All tests were performed at: Global United Technology Services Co., Ltd. Address: 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China Tel: 0755-27798480 Fax: 0755-27798960 5.7 Other Information Requested by the Customer None. Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 6 of 20

Report No.: GTSE14110205302 6 Test Instruments list Radiated Emission: Inventory Cal.Date Cal.Due date Item Test Equipment Manufacturer Model No. No. (mm-dd-yy) (mm-dd-yy) 3m Semi- Anechoic 1 ZhongYu Electron 9.2(L)*6.2(W)* 6.4(H) GTS250 Mar. 28 2014 Mar. 27 2015 Chamber 2 Control Room ZhongYu Electron 6.2(L)*2.5(W)* 2.4(H) GTS251 N/A N/A 3 Spectrum Analyzer Agilent E4440A GTS533 Dec. 4 2014 Dec. 3 2015 4 EMI Test Receiver Rohde & Schwarz ESU26 GTS203 July 01 2014 June 30 2015 SCHWARZBECK 5 BiConiLog Antenna VULB9163 GTS214 July 01 2014 June 30 2015 MESS-ELEKTRONIK Double -ridged waveguide SCHWARZBECK 6 9120D-829 GTS208 June 27 2014 June 26 2015 horn MESS-ELEKTRONIK 7 Horn Antenna ETS-LINDGREN 3160 GTS217 Mar. 28 2014 Mar. 27 2015 8 EMI Test Software AUDIX E3 N/A N/A N/A 9 Coaxial Cable GTS N/A GTS213 Mar. 29 2014 Mar. 28 2015 10 Coaxial Cable GTS N/A GTS211 Mar. 29 2014 Mar. 28 2015 11 Coaxial cable GTS N/A GTS210 Mar. 29 2014 Mar. 28 2015 12 Coaxial Cable GTS N/A GTS212 Mar. 29 2014 Mar. 28 2015 13 Amplifier(100kHz-3GHz) HP 8347A GTS204 July 01 2014 June 30 2015 14 Amplifier(2GHz-20GHz) HP 8349B GTS206 July 01 2014 June 30 2015 AFS33-18002 15 Amplifier (18-26GHz) Rohde & Schwarz GTS218 June 27 2014 June 26 2015 650-30-8P-44 16 Band filter Amindeon 82346 GTS219 Mar. 29 2014 Mar. 28 2015 17 Power Meter Anritsu ML2495A GTS540 July 01 2014 June 30 2015 18 Power Sensor Anritsu MA2411B GTS541 July 01 2014 June 30 2015 Conducted Emission: Inventory Cal.Date Cal.Due date Item Test Equipment Manufacturer Model No. No. (mm-dd-yy) (mm-dd-yy) 1 Shielding Room ZhongYu Electron 7.0(L)x3.0(W)x3.0(H) GTS264 Sep. 07 2013 Sep. 06 2015 2 EMI Test Receiver Rohde & Schwarz ESCS30 GTS223 July 01 2014 June 30 2015 3 10dB Pulse Limita Rohde & Schwarz N/A GTS224 July 01 2014 June 30 2015 4 Coaxial Switch ANRITSU CORP MP59B GTS225 July 01 2014 June 30 2015 SCHWARZBECK 5 LISN NSLK 8127 GTS226 July 01 2014 June 30 2015 MESS-ELEKTRONIK 6 Coaxial Cable GTS N/A GTS227 July 01 2014 June 30 2015 7 EMI Test Software AUDIX E3 N/A N/A N/A General used equipment: Inventory Cal.Date Cal.Due date Item Test Equipment Manufacturer Model No. No. (mm-dd-yy) (mm-dd-yy) 1 Barometer ChangChun DYM3 GTS257 July 08 2014 July 07 2015 Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 7 of 20

Report No.: GTSE14110205302 7 Test results and Measurement Data 7.1 Antenna requirement: Standard requirement: FCC Part15 C Section 15.203 15.203 requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. E.U.T Antenna: The antenna is Internal Integral antenna, the best case gain of the antenna is 0dBi RF Antenna Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 8 of 20

Report No.: GTSE14110205302 7.2 Conducted Emissions Test Requirement: FCC Part15 C Section 15.207 Test Method: ANSI C63.4:2009 Test Frequency Range: 150KHz to 30MHz Class / Severity: Class B Receiver setup: RBW=9KHz, VBW=30KHz, Sweep time=auto Limit: Limit (dBuV) Frequency range (MHz) Quasi-peak Average 0.15-0.5 66 to 56* 56 to 46* 0.5-5 56 46 5-30 60 50 * Decreases with the logarithm of the frequency. Test setup: Test procedure: 1. The E.U.T is connected to the main power through a line impedance stabilization network (L.I.S.N.). This provides a 50ohm/50uH coupling impedance for the measuring equipment. 2. The peripheral devices are also connected to the main power through a LISN that provides a 50ohm/50uH coupling impedance with 50ohm termination. (Please refer to the block diagram of the test setup and photographs). 3. Both sides of A.C. line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ANSI C63.4: 2009 on conducted measurement. Test Instruments: Refer to section 6.0 for details Test mode: Refer to section 5.3 for details Test results: Pass Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 9 of 20

Report No.: GTSE14110205302 Measurement data Line: Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 10 of 20

Report No.: GTSE14110205302 Neutral: Notes: 1. An initial pre-scan was performed on the line and neutral lines with peak detector. 2. Quasi-Peak and Average measurement were performed at the frequencies with maximized peak emission. 3. Final Level =Receiver Read level + LISN Factor + Cable Loss 4. If the average limit is met when using a quasi-peak detector receiver, the EUT shall be deemed to meet both limits and measurement with the average detector receiver is unnecessary. Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 11 of 20

Report No.: GTSE14110205302 7.3 Radiated Emission Method Test Requirement: FCC Part15 C Section 15.209 Test Method: ANSI C63.4:2009 Test Frequency Range: 30MHz to 10GHz Test site: Measurement Distance: 3m Receiver setup: Frequency Detector RBW VBW Remark 30MHz- Quasi-peak 120KHz 300KHz Quasi-peak Value 1GHz Peak 1MHz 3MHz Peak Value Above 1GHz Peak 1MHz 10Hz Average Value For the field strength test, the RBW and VBW were set to 300kHz and 1MHz. Limit: Frequency Limit (dBuV/m @3m) Remark (Field strength of the 902MHz ~ 928MHz 94.00 Quasi-peak fundamental signal) Limit: Frequency Limit (dBuV/m @3m) Remark (Spurious Emissions) 30MHz-88MHz 40.00 Quasi-peak Value 88MHz-216MHz 43.50 Quasi-peak Value 216MHz-960MHz 46.00 Quasi-peak Value 960MHz-1GHz 54.00 Quasi-peak Value 54.00 Average Value Above 1GHz 74.00 Peak Value Limit: Emissions radiated outside of the specified frequency bands, except for (band edge) harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in Section 15.209, whichever is the lesser attenuation. Test setup: Below 1GHz Above 1GHz Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 12 of 20

Report No.: GTSE14110205302 Test Procedure: 1. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter camber. The table was rotated 360 degrees to determine the position of the highest radiation. 2. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. 3. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. 4. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rota table was turned from 0 degrees to 360 degrees to find the maximum reading. 5. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. 6. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. Test Instruments: Refer to section 6.0 for details Test mode: Refer to section 5.3 for details Test results: Pass Measurement data: Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 13 of 20

Report No.: GTSE14110205302 7.3.1 Field Strength of The Fundamental Signal Quasi-peak value: Read Antenna Cable Preamp Over Frequency Level Limit Line Level Factor Loss Factor Limit polarization (MHz) (dBuV/m) (dBuV/m) (dBuV) (dB/m) (dB) (dB) (dB) 915.00 89.21 23.18 4.91 29.10 88.20 94.00 -5.80 Horizontal 915.00 90.11 23.18 4.91 29.10 89.10 94.00 -4.90 Vertical 7.3.2 Spurious emissions  Below 1GHz Read Antenna Cable Preamp Over Frequency Level Limit Line Level Factor Loss Factor Limit polarization (MHz) (dBuV/m) (dBuV/m) (dBuV) (dB/m) (dB) (dB) (dB) 54.84 39.17 15.02 0.82 29.96 25.05 40.00 -14.95 Vertical 103.08 39.41 14.87 1.22 29.68 25.82 43.50 -17.68 Vertical 268.49 39.77 14.34 2.21 29.79 26.53 46.00 -19.47 Vertical 393.47 39.95 16.92 2.82 29.53 30.16 46.00 -15.84 Vertical 533.83 39.60 19.26 3.46 29.30 33.02 46.00 -12.98 Vertical 958.79 39.85 23.49 5.08 29.10 39.32 46.00 -6.68 Vertical 31.40 40.00 14.32 0.57 30.09 24.80 40.00 -15.20 Horizontal 57.80 39.59 14.84 0.84 29.94 25.33 40.00 -14.67 Horizontal 103.08 39.84 14.87 1.22 29.68 26.25 43.50 -17.25 Horizontal 155.91 40.48 10.51 1.60 29.38 23.21 43.50 -20.29 Horizontal 214.51 39.34 13.03 1.93 29.35 24.95 43.50 -18.55 Horizontal 776.88 40.96 21.77 4.37 29.20 37.90 46.00 -8.10 Horizontal Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 14 of 20

Report No.: GTSE14110205302  Above 1GHz Peak value: Read Antenna Cable Preamp Over Frequency Level Limit Line Level Factor Loss Factor Limit polarization (MHz) (dBuV/m) (dBuV/m) (dBuV) (dB/m) (dB) (dB) (dB) 1830.00 39.72 25.42 4.87 34.17 35.84 74.00 -38.16 Vertical 2745.00 44.66 28.24 5.71 33.61 45.00 74.00 -29.00 Vertical 3660.00 39.37 29.20 7.27 32.56 43.28 74.00 -30.72 Vertical 4575.00 41.33 31.47 8.40 31.97 49.23 74.00 -24.77 Vertical 5490.00 39.76 31.98 9.49 32.42 48.81 74.00 -25.19 Vertical 6405.00 31.50 33.49 10.78 32.11 43.66 74.00 -30.34 Vertical 7320.00 30.84 36.37 11.72 31.89 47.04 74.00 -26.96 Vertical 8235.00 31.57 36.76 12.47 31.73 49.07 74.00 -24.93 Vertical 9150.00 28.92 37.31 13.78 32.13 47.88 74.00 -26.12 Vertical 1830.00 39.30 25.42 4.87 34.17 35.42 74.00 -38.58 Horizontal 2745.00 43.51 28.24 5.71 33.61 43.85 74.00 -30.15 Horizontal 3660.00 38.70 29.20 7.27 32.56 42.61 74.00 -31.39 Horizontal 4575.00 36.51 31.47 8.40 31.97 44.41 74.00 -29.59 Horizontal 5490.00 31.67 31.98 9.49 32.42 40.72 74.00 -33.28 Horizontal 6405.00 31.89 33.49 10.78 32.11 44.05 74.00 -29.95 Horizontal 7320.00 29.80 36.37 11.72 31.89 46.00 74.00 -28.00 Horizontal 8235.00 29.95 36.76 12.47 31.73 47.45 74.00 -26.55 Horizontal 9150.00 29.09 37.31 13.78 32.13 48.05 74.00 -25.95 Horizontal Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 15 of 20

Report No.: GTSE14110205302 Average value: Read Antenna Cable Preamp Over Frequency Level Limit Line Level Factor Loss Factor Limit polarization (MHz) (dBuV/m) (dBuV/m) (dBuV) (dB/m) (dB) (dB) (dB) 1830.00 * Vertical 2745.00 * Vertical 3660.00 * Vertical 4575.00 * Vertical 5490.00 * Vertical 6405.00 * Vertical 7320.00 * Vertical 8235.00 * Vertical 9150.00 * Vertical 1830.00 * Horizontal 2745.00 * Horizontal 3660.00 * Horizontal 4575.00 * Horizontal 5490.00 * Horizontal 6405.00 * Horizontal 7320.00 * Horizontal 8235.00 * Horizontal 9150.00 * Horizontal Remark: 1. Final Level =Receiver Read level + Antenna Factor + Cable Loss – Preamplifier Factor 2. The emission levels of other frequencies are very lower than the limit and not show in test report. 3. (*)The test result on peak is lower than average limit, then average measurement needn’t be performed. Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 16 of 20

Report No.: GTSE14110205302 7.3.3 Bandedge emissions All of the restriction bands were tested, and only the data of worst case was exhibited. Quasi-peak value: Read Antenna Cable Preamp Over Frequency Level Limit Line Level Factor Loss Factor Limit Polarization (MHz) (dBuV/m) (dBuV/m) (dBuV) (dB/m) (dB) (dB) (dB) 902.00 28.18 23.12 4.87 29.10 27.07 46.00 -18.93 Horizontal 928.00 28.56 23.28 4.96 29.10 27.70 46.00 -18.30 Horizontal 902.00 27.11 23.12 4.87 29.10 26.00 46.00 -20.00 Vertical 928.00 28.36 23.28 4.96 29.10 27.50 46.00 -18.50 Vertical Remark: 1. Final Level =Receiver Read level + Antenna Factor + Cable Loss – Preamplifier Factor 2. If the average limit is met when using a quasi-peak detector receiver, the EUT shall be deemed to meet both limits and measurement with the average detector receiver is unnecessary. Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 17 of 20

Report No.: GTSE14110205302 7.4 20dB Occupy Bandwidth Test Requirement: FCC Part15 C Section 15.249/15.215 Test Method: ANSI C63.4:2009 Limit: Operation Frequency range 902MHz ~ 928MHz Test setup: Test Instruments: Refer to section 6.0 for details Test mode: Refer to section 5.3 for details Test results: Pass Measurement Data Operation Frequency 20dB bandwidth(MHz) Result 915MHz 0.232 Pass Test plot as follows: Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 18 of 20

Report No.: GTSE14110205302 8 Test Setup Photo Radiated Emission Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 19 of 20

Report No.: GTSE14110205302 Conducted Emission 9 EUT Constructional Details Reference to the test report No. GTSE14110205301 ------End------ Global United Technology Services Co., Ltd. Project No.: GTSE141102053RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 20 of 20


Document Created: 2015-03-20 11:42:45
Document Modified: 2015-03-20 11:42:45
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC