FCC Part 15.247 Test Report

FCC ID: 2ADLNXY4D1

Test Report

Download: PDF
FCCID_3629956

Test Report Prepared for: SMK USA Model: XY4D Description: This is a TAG that tracks valuables. These valuables can be items or people. It performs this by finding its location with BLE beacon. It transmites its position via BLE Serial Number: 8 FCC ID: 2ADLN-XY4D1 IC: 12506A-XY4D1 To FCC Part 15.247 IC RSS-247 Date of Issue: November 6, 2017 On the behalf of the applicant: XY – The Findables Company 1133 Columbia St. Suite 205 San Diego, CA 92101 By the request of: SMK Manufacturing, Inc. 1055 Tierra Del Rey Suite H Chila Vista, CA 91910 Attention of: Leon Gateno, Sr RF Engineer Ph: (619)216-6425 Email: lgateno@smkusa.com Prepared By Compliance Testing, LLC 1724 S. Nevada Way Mesa, AZ 85204 (480) 926-3100 phone / (480) 926-3598 fax www.compliancetesting.com Project No: p1790001 Kenneth Lee Project Test Engineer This report may not be reproduced, except in full, without written permission from Compliance Testing. All results contained herein relate only to the sample tested. p1740020_FCC_Part 15.247_Rev 2.0 Page 1 of 18

Test Report Revision History Revision Date Revised By Reason for Revision 1.0 September 25, 2017 Kenneth Lee Original Document Added Environmental Information, Updated version 2.0 November 6, 2017 Kenneth Lee number of used KDB. p1740020_FCC_Part 15.247_Rev 2.0 Page 2 of 18

Table of Contents Description Page Standard Test Conditions Engineering Practices ............................................................................... 6 Output Power ...................................................................................................................................... 8 Radiated Spurious Emissions ............................................................................................................. 9 Emissions at Band Edges ................................................................................................................. 10 DTS Bandwidth ................................................................................................................................. 12 Transmitter Power Spectral Density (PSD) ....................................................................................... 15 Test Equipment Utilized .................................................................................................................... 18 p1740020_FCC_Part 15.247_Rev 2.0 Page 3 of 18

ILAC / A2LA Compliance Testing, LLC, has been accredited in accordance with the recognized International Standard ISO/IEC 17025:2005. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to the joint ISO-ILAC-IAF Communiqué dated January 2009). The tests results contained within this test report all fall within our scope of accreditation, unless noted below. Please refer to http://www.compliancetesting.com/labscope.html for current scope of accreditation. Testing Certificate Number: 2152.01 FCC Site Reg. #349717 IC Site Reg. #2044A-2 Non-accredited tests contained in this report: N/A p1740020_FCC_Part 15.247_Rev 2.0 Page 4 of 18

The applicant has been cautioned as to the following 15.21 - Information to User The user’s manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 15.27(a) - Special Accessories Equipment marked to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer without an additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. p1740020_FCC_Part 15.247_Rev 2.0 Page 5 of 18

Standard Test Conditions Engineering Practices Except as noted herein, the following conditions and procedures were observed during the testing: In accordance with ANSI C63.10-2013 and unless otherwise indicated in the specific measurement results, the ambient temperature of the actual EUT was maintained within the range of 10° to 40°C (50° to 104°F) unless the particular equipment requirements specified testing over a different temperature range. Also, unless otherwise indicated, the humidity levels were in the range of 10% to 90% relative humidity. Measurement results, unless otherwise noted, are worst-case measurements. Environmental Conditions Temperature Humidity Pressure (ºC) (%) (mbar) 19-26 30-38 966-974 EUT Description Model: XY4D Description: This is a TAG that tracks valuables. These valuables can be items or people. It performs this by finding its location with BLE beacon. It transmites its position via BLE Firmware: codeless_585 Software: N/A Serial Number: 8 Additional Information: The EUT implements BLE modulation. EUT Operation during Tests The EUT was set to transmit at the lowest, middle and highest channel of operation at the maximum available power setting. The EUT was controlled via TeraTerm software on a laptop computer. Accessories: None Cables: None Modifications: None 15.203: Antenna Requirement: X The antenna is permanently attached to the EUT The antenna uses a unique coupling The EUT must be professionally installed The antenna requirement does not apply p1740020_FCC_Part 15.247_Rev 2.0 Page 6 of 18

Test Results Summary FCC 15.247 RSS-247 Pass, Test Name Comments Specification Specification Fail, N/A 15.247(b) Section 5.4(d) Output Power Pass 15.247(d) Section 5.5 Conducted Spurious Emissions N/A EUT has no Antenna Port 15.247(d), Section 5.5 Radiated Spurious Emissions Pass 15.209(a), 15.205 15.247(d), Section 5.5 Emissions At Band Edges Pass 15.209(a), 15.205 15.247(a)(2) Sections 5.2(a) Occupied Bandwidth Pass 15.247(e) Section 5.2(b) Transmitter Power Spectral Density Pass RSS-GEN 15.207 A/C Powerline Conducted Emissions N/A EUT is Battery Powered Section 8.8 References Description CFR47, Part 15, Subpart B Unintentional Radiators CFR47, Part 15, Subpart C Intentional Radiators ANSI C63.10-2013 American National standard for testing Unlicensed Wireless Devices Method and Measurements of Radio-Noise Emissions from low-Voltage ANSI C63.4-2014 Electrical and Electronic Equipment in the range 9kHz to 40GHz. General requirements for the Competence of Testing and Calibrations ISO/IEC 17025:2005 Laboratories Guidance for Performing Compliance Measurements on Digital Transmission KDB 558074 D01 v04 Systems (DTS) Operating under §15.247 p1740020_FCC_Part 15.247_Rev 2.0 Page 7 of 18

Output Power Engineer: Kenneth Lee Test Date: 9/25/2017 Test Procedure The EUT was setup in a semi-anechoic test chamber set 3m from the receiving antenna. The EUT was set to transmit on the lowest, middle and highest frequency of operation at the maximum power level. The EUT was tested, in 3 orthogonal axis, by rotating it 360 with the receive antenna in both the vertical and horizontal orientation while raised from 1 to 4 meters to ensure the TX signal levels were maximized. A spectrum analyzer was used to verify that the EUT met the requirements for Output Power. The Spectrum Analyzer was set to the following: RBW ≥ DTS Bandwidth VBW ≥ 3 x RBW Span ≥ 3 x RBW Sweep time = auto couple Detector = peak Trace Mode = max hold Test Setup EUT Antenna Spectrum Analyzer Transmitter Output Power Summary Table Tuned Frequency Measured Value Specification Limit Result (MHz) (dBm) 2402 5.971 1 W (30 dBm) Pass 2452 3.093 1 W (30 dBm) Pass 2480 -1.431 1 W (30 dBm) Pass p1740020_FCC_Part 15.247_Rev 2.0 Page 8 of 18

Radiated Spurious Emissions Engineer: Kenneth Lee Test Date: 9/25/2017 Test Procedure Radiated Spurious Emissions: 30 – 1000 MHz The EUT was setup in a semi-anechoic test chamber set 3m from the receiving antenna. The EUT was set to transmit on the lowest, middle and highest frequency of operation at the maximum power level. The EUT was tested, in 3 orthogonal axis, by rotating it 360 with the receive antenna in both the vertical and horizontal orientation while raised from 1 to 4 meters to ensure the TX signal levels were maximized. A spectrum analyzer was used to verify that the EUT met the requirements for Radiated Spurious Emissions. All emissions from 30 MHz to 1 GHz were examined. Measured Level includes antenna and receiver cable correction factors. Correction factors were input into the spectrum analyzer before recording “Measured Level”. RBW = 100 KHz VBW = 300 KHz Detector – Quasi Peak Test Setup EUT Antenna Spectrum Analyzer Test Procedure for Radiated Spurious Emissions above 1 GHz The EUT was setup in a semi-anechoic test chamber set 3m from the receiving antenna. The EUT was set to transmit on the lowest, middle and highest frequency of operation at the maximum power level. The EUT was tested, in 3 orthogonal axis, by rotating it 360 with the receive antenna in both the vertical and horizontal orientation while raised from 1 to 4 meters to ensure the TX signal levels were maximized. A spectrum analyzer was used to verify that the EUT met the requirements for Radiated Spurious Emissions. RBW = 100 KHz and 1 MHz VBW = 300 KHz and 3 MHz Detector – Peak Test Setup Band Reject EUT Antenna Filter Amplifier Spectrum Analyzer (if necessary See Annex A for test data p1740020_FCC_Part 15.247_Rev 2.0 Page 9 of 18

Emissions at Band Edges Engineer: Kenneth Lee Test Date: 8/1/2017 Test Procedure The EUT was setup in a semi-anechoic test chamber set 3m from the receiving antenna. The EUT was set to transmit on the lowest and highest frequency of operation at the maximum power level. The EUT was tested, in 3 orthogonal axis, by rotating it 360 with the receive antenna in both the vertical and horizontal orientation while raised from 1 to 4 meters to ensure the TX signal levels were maximized. A spectrum analyzer was used to verify that the EUT met the requirements for band edges. Test Setup EUT Antenna Spectrum Analyzer Band Edge Emissions Summary Tuned Frequency Emission Frequency Monitored Level Detector Limit Result (MHz) (MHz) 2402 2400 -22.92 Peak -20 dBc Pass 2480 2483.5 -42.97 Peak -20 dBc Pass p1740020_FCC_Part 15.247_Rev 2.0 Page 10 of 18

Band Edge Plots Low Channel High Channel p1740020_FCC_Part 15.247_Rev 2.0 Page 11 of 18

DTS Bandwidth Engineer: Kenneth Lee Test Date: 9/25/2017 Test Procedure The EUT was setup in a semi-anechoic test chamber set 3m from the receiving antenna. The EUT was set to transmit on the lowest, middle and highest frequency of operation at the maximum power level. The EUT was tested, in 3 orthogonal axis, by rotating it 360 with the receive antenna in both the vertical and horizontal orientation while raised from 1 to 4 meters to ensure the TX signal levels were maximized. A spectrum analyzer was used to verify that the EUT met the Bandwidth requirements. The Spectrum Analyzer was set to the following: RBW = 100 kHz VBW ≥ 3 x RBW Peak Detector Trace mode = max hold Sweep = auto couple Span = 1.5 x EBW Test Setup EUT Antenna Spectrum Analyzer 6 dB Occupied Bandwidth Summary Frequency Measured Bandwidth Specification Limit Result (MHz) (kHz) (kHz) 2402 712.179 ≥ 500 Pass 2452 744.151 ≥ 500 Pass 2480 747.587 ≥ 500 Pass 99% Bandwidth Summary Frequency Measured Bandwidth Result (MHz) (kHz) 2402 1.0837 Pass 2452 1.1026 Pass 2480 1.1089 Pass p1740020_FCC_Part 15.247_Rev 2.0 Page 12 of 18

6 dB and 99% Bandwidth Plots Low Channel Mid Channel p1740020_FCC_Part 15.247_Rev 2.0 Page 13 of 18

High Channel p1740020_FCC_Part 15.247_Rev 2.0 Page 14 of 18

Transmitter Power Spectral Density (PSD) Engineer: Kenneth Lee Test Date: 9/25/2017 Test Procedure The EUT was setup in a semi-anechoic test chamber set 3m from the receiving antenna. The EUT was set to transmit on the lowest, middle and highest frequency of operation at the maximum power level. The EUT was tested, in 3 orthogonal axis, by rotating it 360 with the receive antenna in both the vertical and horizontal orientation while raised from 1 to 4 meters to ensure the TX signal levels were maximized. A spectrum analyzer was used to verify that the EUT met the requirements. The Spectrum Analyzer was set to the following: DTS channel center frequency Span 1.5 x DTS bandwidth RBW =3 kHz ≤ RBW ≤ 100 kHz VBW ≥ 3 x RBW Peak Detector Sweep time = auto couple Trace mode = max hold Once the trace has stabilized the peak marker was used to determine the power spectral density. Test Setup EUT Antenna Spectrum Analyzer PSD Summary Frequency Measured Data Specification Limit Result (MHz) (dBm) (dBm) 2402 -8.88 8 Pass 2452 -11.69 8 Pass 2480 -16.36 8 Pass p1740020_FCC_Part 15.247_Rev 2.0 Page 15 of 18

PSD Plots Low Channel Mid Channel p1740020_FCC_Part 15.247_Rev 2.0 Page 16 of 18

High Channel p1740020_FCC_Part 15.247_Rev 2.0 Page 17 of 18

Test Equipment Utilized Last Cal Cal Due Description Manufacturer Model # CT Asset # Date Date Horn Antenna ARA DRG-118/A i00271 6/16/16 6/16/18 Humidity / Temp Meter Newport IBTHX-W-5 i00282 6/9/17 6/9/18 Bi-Log Antenna Schaffner CBL 6111D i00349 8/3/16 8/3/18 3 Meter Semi-Anechoic 3 Meter Semi-Anechoic Panashield i00428 8/15/16 8/15/19 Chamber Chamber EMI Analyzer Agilent E7405A i00379 2/22/17 2/22/18 Spectrum Analyzer Agilent E4407B i00331 10/19/16 10/19/17 Preamplifier for 1-18GHz AFS44 00101 400 23- Miteq i00509 N/A N/A horn antenna 10P-44 In addition to the above listed equipment standard RF connectors and cables were utilized in the testing of the described equipment. Prior to testing these components were tested to verify proper operation. END OF TEST REPORT p1740020_FCC_Part 15.247_Rev 2.0 Page 18 of 18


Document Created: 2017-11-06 11:43:35
Document Modified: 2017-11-06 11:43:35
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC