Modular Appr Letter

FCC ID: 2ADHKBM83SM1

Cover Letter(s)

Download: PDF
FCCID_4191035

Applicant/Grantee        Microchip Technology Inc.
FCC ID:                  2ADHKBM83SM1                   |                       |
                                     Section 15.212 Modular Transmitters /
     Request for Modular Approval |            | Request for Limited Modular Approval
       |                 Requirements                          Device Conditions                    Comply (Y¥/N)
                                    Single Modular Approval Requirements
          The radio elements must have the radio            This module has shielding case.
          frequency circuitry shielded.
          Physical/discrete and tuning capacitors
          may be located external to the shield, but
          must be on the module assembly.

          [The module shall have buffered              All modulation and data input(s) are
          modulation/data input(s) (if such inputs are buffered. The EUT has buffered data
          provided) to ensure that the module will     inputs, it is integrated on the RF chip
          comply with the requirements set out in the
          applicable RSS standard under conditions
          of excessive data rates or over—modulation.


          The module shall have its own power               Bluetooth system on Chip IC contains
          supply regulation on the module. This is to       multiple dedicated voltage regulators
          ensure that the module will comply with           for transmitter chain including
          the requirements set out in the applicable        modulator, per—power amplifier, and
          standard regardless of the design of the          power amplifier.
          power supplying circuitry in the host
          device which houses the module.
          Requirements set out in the applicable
          standard regardless of the
          design of the power supplying circuitry in
          the host device which houses the module.
          [The module shall comply with the           The Module has a Printed antenna.
          provisions for external power amplifiers
          and antennas detailed in this standard. The
          Equipment certification submission shall
          contain a detailed description of the
          configuration of all antennas that will be
          used with the module.




           The module shall be tested for compliance See Setup Photos
           with the applicable standard in a stand—
           alone configuration, i.e. the module must
           not be inside another device during testing.


           The modular transmitter must be                  See Label Exhibit
           equipped with either a permanently affixed
           label.


         The modular transmitter complies with all    Instructions in User Manual
         specific rules or operating requirements
         that ordinarily apply to a complete
         transmitter and the manufacturer will
    7    |provide adequate instructions along with                                                      y
         the module to explain any such
         requirements. A copy of these instructions
         is included in this application for
         equipment authorization:

         Address compliance with the                  Instructions are given in the installation
         Commission‘s RF exposure limits in           manual for compliance to the RF
         Sections 1.1310 and 2.1093. In addition,     exposure requirements.
         spread spectrum transmitters operating
         under Section 15.247 are required to
         address RF exposure compliance in
         accordance with Section 15.247(b)(4).

A limited modular approval may be granted for single or split modular transmitters that do not comply with
all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or
power supply regulation, if the manufacturer can demonstrate by alternative means in the application for
equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the
operating conditions in which the transmitter will be used. Limited modular approval also may be granted in
those instances where compliance with RF exposure rules is demonstrated only for particular product
configurations. The applicant for certification must state how control of the end product into which the module
will be installed will be maintained such that full compliance of the end product is always ensured.




    TCP

Signature
Name/Title: Steve Caldwell / Vice President
Company Name: Microchip Technology Inc.
Date: 21 Feb 2019



Document Created: 2019-07-08 22:54:08
Document Modified: 2019-07-08 22:54:08

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC