User Manual

FCC ID: 2AD9X-KFG

Users Manual

Download: PDF
FCCID_4436544

GE Keyfob Manual Installation Instructions The Versa KeyfobG is a 4‐button key ring remote. The KeyfobG enables you to turn the GE system on and off before entering the home or after exiting. If there is an emergency, you can turn on the siren and automatically call the central monitoring station. If lamp modules have been installed, you can use the key fob to turn all system‐controlled lights on or off via the open collector output. Use with the GE Alarm System to open a garage door. The KeyfobG is a lithium coin battery‐powered, wireless key fob designed to fit on a keychain, in a pocket, or in a purse. It provides a convenient option for the following system operations: • Arm the system (doors, windows, and motion sensors). • Arm the system with no entry delay (if programmed). • Disarm the system. • Trigger panic alarms. • Turn system‐controlled lights on or off (via the open collector output) • Other open collector output functions (if applicable) • Use with the GE Alarm System to open a garage door. See the Testing GE install instructions. 1. From the Installer Toolbox, select walk test. brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the Away any interference, including interference that may cause undesired operation of the device.Le présent following two conditions: (1) this device may not cause interference, and (2) this device must accept 2. To test the disarm button, hold the button down for 2 Programming seconds. This disarms the Control Panel as well as the doors, L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de The following steps are for programming (learning) the sensor Versa Disarm windows, and motion detectors. KeyfobG into the GE control panel. Scroll between options using the ← 3. To test the away button, hold the button down for 2 and → arrows. Move to the previous or next prompt by pressing the ↑ Stay seconds. This arms the Control Panel as well as the doors and ↓ arrows. and windows (in Away mode). 1. Go to Q3: Select fob # (1 to 8). 4. To test the stay button, hold the button down for 2 Auxiliary 2. Fob used (0 to 1) or Fob enabled (0 to 1). seconds. This arms the Control Panel as well as the doors (0) unused (1) used (0) disabled (1) enabled and windows (in Stay mode). 5. To test the Auxiliary button (if previously programmed, brouillage est susceptible d'en compromettre le fonctionnement. 3. Select RF sensor equipment code. Enter 0866 for the Versa Key 4‐button key ring remote. this button can trigger a pre-selected output). 4. Enter RF sensor serial number (7 digits). 6. To test the Away and Disarm buttons (if the emergency key Inserting & Replacing Manual Entry: Type in the last 7 digits of the TX ID that is found was programmed in step 6 above), pressing both the Away Batteries continued... outside of the box or on the back of the device. and Disarm buttons at the same time for 5 seconds sends Auto Entry: With the panel in learn‐in mode (press Shift then Replace only with the same or one of four types of emergency signals: Learn). The correct TX ID should appear. Accept the correct TX ID equivalent type of battery as (1) silent panic (2) audible alarm (3) silent panic (4) fire by pressing OK. Remember to press the ↓ arrow to continue going recommended by the 7. Exit the Installer Toolbox. through the 2GIG system configuration prompts. manufacturer. See 5. Select RF sensor equipment age (0 to 1). specifications. Batteries must (0) new (product is new) (1) existing (product already exists) not be recharged, FCC Notice 6. Select fob emergency key (0 to 4). disassembled or disposed of in This device comples with FCC Rules Part 15. Operation is subject to the (0) disabled (1) auxiliary alarm (2) audible alarm (3) silent panic fire. Disposal of used batteries following two conditions: must be made in accordance 1. this device may not cause interference, and IC Notice (4) fire with the waste recovery and 7. Select fob key 2 can disarm (0 to 1). 2. this device must accept any interference, including interference recycling regulations in your (0) disabled (1) enabled that may cause undesired operation of the device¹. area. Keep away from small 8. Construct RF sensor voice descriptor. NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR children. If batteries are Press Insert then press any number between 002 and 255 to add a MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE swallowed, promptly seek word. For example, if you wanted to name this key ring remote as FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S medical attention. “main key remote,” press Insert then press 138 for MAIN. Press AUTHORITY TO OPERATE THE EQUIPMENT Insert then press 121 for KEY. Press Insert then press 183 for California Only: This Perchlorate Remote. warning applies only to Manganese Dioxide Lithium cells 9. Select fob arm no delay (0 to 1). sold or distributed ONLY in / (0) disabled (1) enabled California, U.S.A. Perchlorate 10. Select fob key 4 output (0 to 2). Material‐special handling may (0) disabled (1) toggle output (2) momentary output apply. See dtsc.ca.gov/hazard- 11. To program another sensor click next. ouswaste/perchlorate. 12. To exit programming, click skip then end and exit. Upon exit, the panel takes a several seconds to reboot. Tip: Each key fob that is learned in uses one of the available fob sensor numbers as programmed in step 1. Inserting & Replacing Batteries WARNING: The polarity of the battery must be observed, as shown. Improper handling of lithium batteries may result in heat generation, explosion or fire, resulting in personal injuries. Continued >


Document Created: 2019-07-29 14:28:06
Document Modified: 2019-07-29 14:28:06
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC