FCC Part 25 Test Report_Part1_rev 3.pdf

FCC ID: 2AD8UFZMFWH201

Test Report

Download: PDF
FCCID_4320433

MRT Technology (Taiwan) Co., Ltd Report No.: 1812TW0108-U1 Phone: +886-3-3288388 Report Version: V01 Web: www.mrt-cert.com Issue Date: 05-03-2019 MEASUREMENT REPORT FCC PART 25 Subpart B LTE FCC ID: 2AD8UFZMFWH201 Applicant: Nokia Solutions and Networks, OY Application Type: Certification Product: Flexi Zone 2400 Model No.: FWH2 Brand Name: Nokia FCC Classification: Licensed Non-Broadcast Station Transmitter (TNB) FCC Rule Part(s): Part 25 Subpart B (Section 25.149) Test Procedure(s): ANSI C63.26-2015, KDB 971168 D01v03r01 Test Date: April 02 ~ 12, 2018 Reviewed By: ( Paddy Chen ) Approved By: (Chenz Ker) The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.26-2015. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Taiwan) Co., Ltd. FCC ID: 2AD8UFZMFWH201 Page Number: 1 of 50

Report No.: 1812TW0108-U1 Revision History Report No. Version Description Issue Date Note 1812TW0108-U1 Rev. 01 Initial Report 05-03-2019 Valid FCC ID: 2AD8UFZMFWH201 Page Number: 2 of 50

Report No.: 1812TW0108-U1 CONTENTS Description Page 1. INTRODUCTION ...................................................................................................................... 6 1.1. Scope ........................................................................................................................... 6 1.2. MRT Test Location ....................................................................................................... 6 2. PRODUCT INFORMATION ...................................................................................................... 7 2.1. Feature of Equipment under Test ................................................................................. 7 2.2. Emission Designator .................................................................................................... 7 2.3. Antenna Information ..................................................................................................... 8 2.4. Details of Test Mode .................................................................................................... 8 2.5. Device Capabilities ....................................................................................................... 8 2.6. Test Configuration ........................................................................................................ 9 2.7. EMI Suppression Device(s)/Modifications..................................................................... 9 3. TEST EQUIPMENT CALIBRATION DATE ............................................................................. 10 4. MEASUREMENT UNCERTAINTY ......................................................................................... 11 5. TEST RESULT ....................................................................................................................... 12 5.1. Summary .................................................................................................................... 12 5.2. 6dB Bandwidth ........................................................................................................... 13 5.2.1. Test Limit ................................................................................................................ 13 5.2.2. Test Procedure ....................................................................................................... 13 5.2.3. Test Setting............................................................................................................. 13 5.2.4. Test Setup .............................................................................................................. 13 5.2.5. Test Result.............................................................................................................. 14 5.3. Maximum Transmit Power .......................................................................................... 23 5.3.1. Test Limit ................................................................................................................ 23 5.3.2. Test Procedure ....................................................................................................... 23 5.3.3. Test Setting............................................................................................................. 23 5.3.4. Test Setup .............................................................................................................. 23 5.3.5. Test Result.............................................................................................................. 24 5.4. Power Spectral Density Measurement ........................................................................ 25 5.4.1. Test Limit ................................................................................................................ 25 5.4.2. Test Procedure Used .............................................................................................. 25 5.4.3. Test Setting............................................................................................................. 25 5.4.4. Test Setup .............................................................................................................. 26 5.4.5. Test Setup .............................................................................................................. 27 5.5. Frequency Stability Measurement............................................................................... 36 FCC ID: 2AD8UFZMFWH201 Page Number: 3 of 50

Report No.: 1812TW0108-U1 5.5.1. Test Limit ................................................................................................................ 36 5.5.2. Test Procedure Used .............................................................................................. 36 5.5.3. Test Setting............................................................................................................. 36 5.5.4. Test Setup .............................................................................................................. 37 5.5.5. Test Result.............................................................................................................. 38 5.6. Band Edge Measurement ........................................................................................... 39 5.6.1. Test Limit ................................................................................................................ 39 5.6.2. Test Procedure Used .............................................................................................. 39 5.6.3. Test Setting............................................................................................................. 39 5.6.4. Test Setup .............................................................................................................. 40 5.6.5. Test Result.............................................................................................................. 41 5.7. Conducted Spurious Emissions Measurement ........................................................... 42 5.7.1. Test Limit ................................................................................................................ 42 5.7.2. Test Procedure Used .............................................................................................. 42 5.7.3. Test Setting............................................................................................................. 42 5.7.4. Test Setup .............................................................................................................. 43 5.7.5. Test Result.............................................................................................................. 44 5.8. Radiated Spurious Emissions Measurement .............................................................. 47 5.8.1. Test Limit ................................................................................................................ 47 5.8.2. Test Procedure Used .............................................................................................. 47 5.8.3. Test Setting............................................................................................................. 47 5.8.4. Test Setup .............................................................................................................. 48 5.8.5. Test Result.............................................................................................................. 49 6. CONCLUSION ....................................................................................................................... 50 FCC ID: 2AD8UFZMFWH201 Page Number: 4 of 50

Report No.: 1812TW0108-U1 §2.1033 General Information Applicant: Nokia Solutions and Networks, OY Applicant Address: 2000 W. Lucent Lane, Naperville, Illinois, United States, 60563 Manufacturer: Nokia Solutions and Networks, OY Manufacturer Address: 2000 W. Lucent Lane, Naperville, Illinois, United States, 60563 Test Site: MRT Technology (Taiwan) Co., Ltd Test Site Address: No. 38, Fuxing Second Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C) Test Facility / Accreditations Measurements were performed at MRT Laboratory located in Fuxing Rd., Taoyuan, Taiwan ( R.O.C ) MRT facility is a FCC registered (Reg. No. 153292) test facility with the site description report on file and is designated by the FCC as an Accredited Test Film.  MRT facility is an IC registered (MRT Reg. No. 21723-1) test laboratory with the site description on file at Industry Canada.  MRT Lab is accredited to ISO 17025 by the American Association for Laboratory Accreditation (TAF) under the American Association for Laboratory Accreditation Program (TAF Cert. No. 3261) in EMC, Telecommunications and Radio testing for FCC, Industry Taiwan, EU and TELEC Rules. FCC ID: 2AD8UFZMFWH201 Page Number: 5 of 50

Report No.: 1812TW0108-U1 1. INTRODUCTION 1.1. Scope Measurement and determination of electromagnetic emissions (EMC) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Industry Canada Certification and Engineering Bureau. 1.2. MRT Test Location The map below shows the location of the MRT LABORATORY, its proximity to the Taoyuan City. These measurement tests were conducted at the MRT Technology (Taiwan) Co., Ltd. Facility located at No.38, Fuxing 2nd Rd., Guishan Dist., Taoyuan City 33377, Taiwan (R.O.C). FCC ID: 2AD8UFZMFWH201 Page Number: 6 of 50

Report No.: 1812TW0108-U1 2. PRODUCT INFORMATION 2.1. Feature of Equipment under Test Product Name: Flexi Zone 2400 Model No.: FWH2 Brand Name: Nokia Serial No.: EB183400030 Hardware Version: FWH2, 474328A.X11 Software Version: TLF18A GPS Frequency Range: 1575.42MHz FCC ID of Built-in Bluetooth 2AD8UNBTM01 Module: LTE Operating Band: LTE TDD Band 53 Frequency Range: Uplink: 2483.5 ~ 2495 MHz; Downlink: 2483.5 ~ 2495 MHz Carriers: Up to 1 carrier Carrier Bandwidth: 10MHz Type of Modulation: QPSK, 16QAM, 64QAM, 256QAM TX & RX Configuration: 2TX & 2RX Conducted Power: 29.87dBm Maximum Output Power: EIRP: 34.88dBm Emission Designator: Refer to section 2.2 Antenna Information: Refer to section 2.3 Transmit Antenna is connected directly to the 6dB attenuator Accessory Information: Attenuator: Position: One attenuator connected directly to the FWH2 main and diversity antenna ports. Attenuation: 6dB Nokia Part Number: 091860A 2.2. Emission Designator Channel Bandwidth 10MHz: QPSK: 8M95G7D 16QAM: 8M95W7D 64QAM: 8M96W7D 256QAM: 8M95W7D FCC ID: 2AD8UFZMFWH201 Page Number: 7 of 50

m I Report No.: 1812TWO108—U1 2.3. Antenna Information Technology Antenna Type Nokia Part Number Antenna Gain LTE Band 53 Omni Antenna 473227A 20Bi 2.4. Details of Test Mode Test Item Test Frequency Channel Bandwidth Modulation (MHz) (MHz) . QPSK, 16QAM, 6dB Bandwidth 2488.5, 2489, 2490 10 6A4QAM, 256QAM QPSK, 16QAM, Output Power 2488.5, 2489, 2490 10 6A4QAM, 256QAM . QPSK, 16QAM, Power Spectral Density 2488.5, 2489, 2490 10 6A4QAM, 256QAM Frequency Stability 2489 10 16QAM Band Edge 2488.5, 2489, 2490 10 16QAM Conducted Emission 2488.5, 2489, 2490 10 16QAM Radiated Spurious Emission 2488.5, 2489, 2490 10 16QAM Note: Test Items "Band Edge Measurements" & "Conducted Spurious Emissions" & "Radiated Spurious Emissions" have been assessed all the test modes, and showed the worst test data in this report. 2.5. Device Capabilities This device contains the following capabilities: LTE TDD Band 53. Note: The maximum achievable duty cycles for all modes were determined based on measurements performed on a spectrum analyzer in zero—span mode with RBW = 1MHz, VBW = 3MHz, and detector = average. The duty cycles are as follows: Modulation Duty Cycle QPSK 67.5 % 16QAM 67.5 % 6A4QAM 68.0 % 256QAM 68.0 % FCC ID: 2AD8UFZMFWH2O1 Page Number: 8 of 50

Report No.: 1812TW0108-U1 QPSK 16QAM 64QAM 256QAM 2.6. Test Configuration The device was tested per the guidance of KDB 971168 D01v03r01. ANSI C63.26-2015 was used to reference the appropriate EUT setup for radiated spurious emissions testing. 2.7. EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and/or no modifications were made during testing. FCC ID: 2AD8UFZMFWH201 Page Number: 9 of 50

Report No.: 1812TW0108-U1 3. TEST EQUIPMENT CALIBRATION DATE Radiated Emissions - AC1 Instrument Manufacturer Type No. Asset No. Cali. Interval Cali. Due Date Acitve Loop Antenna SCHWARZBECK FMZB 1519B MRTTWA00002 1 year 2019/04/24 Broadband TRILOG SCHWARZBECK VULB 9162 MRTTWA00001 1 year 2019/05/22 Antenna Log-Periodic Antenna SCHWARZBECK VULP 9118A MRTSUE06174 3 years 2019/08/01 Broadband Hornantenna SCHWARZBECK BBHA 9120D MRTSUE06023 1 year 2019/10/19 Broadband Hornantenna SCHWARZBECK BBHA 9120D MRTTWA00003 1 year 2019/04/24 Breitband Hornantenna SCHWARZBECK BBHA 9170 MRTTWA00004 1 year 2019/04/23 Broadband Preamplifier SCHWARZBECK BBV 9718 MRTTWA00005 1 year 2019/04/23 Broadband Amplifier SCHWARZBECK BBV 9721 MRTTWA00006 1 year 2019/04/23 Signal Analyzer R&S FSV40 MRTTWA00007 1 year 2020/03/20 EMI Test Receiver R&S ESR3 MRTTWA00009 1 year 2020/03/19 EXA Signal Analyzer KEYSIGHT N9010A MRTTWA00012 1 year 2019/07/30 Antenna Cable HUBERSUHNER SF106 MRTTWE00010 1 year 2019/05/18 Temperature/Humidity Meter TFA 35.1078.10.IT MRTTWA00032 1 year 2019/05/21 Conducted Test Equipment - TR3 Instrument Manufacturer Type No. Asset No. Cali. Interval Cali. Due Date X-Series USB Peak and KEYSIGHT U2021XA MRTTWA00014 1 year 2019/04/24 Average Power Sensor X-Series USB Peak and KEYSIGHT U2021XA MRTTWA00015 1 year 2020/03/20 Average Power Sensor EXA Signal Analyzer KEYSIGHT N9010A MRTTWA00012 1 year 2019/07/30 Signal Analyzer R&S FSV40 MRTTWA00007 1 year 2020/03/20 Programmable AC Power N4L N4A3 MRTTWA00068 1 year 2020/02/12 Source Temperature/Humidity Meter TFA 35.1078.10.IT MRTTWA00033 1 year 2019/05/21 Software Version Function EMI Software V3 EMI Test Software FCC ID: 2AD8UFZMFWH201 Page Number: 10 of 50

Report No.: 1812TW0108-U1 4. MEASUREMENT UNCERTAINTY Where relevant, the following test uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2. This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k = 2. Conducted Measurement Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 2.65dB Radiated Emission Measurement Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 4.25dB (30M~1G) 4.40dB (1G~18G) FCC ID: 2AD8UFZMFWH201 Page Number: 11 of 50

Report No.: 1812TW0108-U1 5. TEST RESULT 5.1. Summary FCC Test Test Test Test Reference Section(s) Description Limit Condition Result 25.149 6dB bandwidth ≥ 500kHz Conducted Pass Section 5.2 (c)(4)(ii) 25.149 Maximum Conducted ≤ 30dBm; Conducted Pass Section 5.3 (c)(4)(iii) Transmit Power EIRP ≤ 6dBw / Radiated Maximum 25.149 (c)(4) Power Spectral ≤ 8dBm/3kHz Pass Section 5.4 (iv) Density Frequency 2.1055 N/A Pass Section 5.5 Stability 2.1051; Conducted Band Edge 25.149 (c)(4) Refer to Section 5.6 Pass Section 5.6 Measurements (v) (vi) 2.1051; Conducted 25.149 (c)(4) Spurious Refer to Section 5.7 Pass Section 5.7 (v) (vi) Emissions 2.1053; Radiated 25.149 (c)(4) Spurious Refer to Section 5.8 Radiated Pass Section 5.8 (v) (vi) Emissions Notes: 1. The analyzer plots shown in this section were all taken with a correction table loaded into the analyzer. The correction table was used to account for the losses of the cables and attenuators used as part of the system to connect the EUT to the analyzer at all frequencies of interest. 2. Test Items “Band Edge Measurements” & “Conducted Spurious Emissions” & “Radiated Spurious Emissions” have been assessed all the test modes, and showed the worst test data in this report. FCC ID: 2AD8UFZMFWH201 Page Number: 12 of 50

Report No.: 1812TW0108-U1 5.2. 6dB Bandwidth 5.2.1.Test Limit The minimum 6dB bandwidth shall be at least 500 kHz. 5.2.2.Test Procedure KDB 971168 D01v03r01 - Section 4.2 ANSI C63.26-2015 - Section 5.4.3 5.2.3.Test Setting 1. Set center frequency to the nominal EUT channel center frequency; 2. RBW = 100 kHz (The nominal RBW shall be in the range of 1% to 5% of the anticipated OBW); 3. VBW≧ 3 × RBW; 4. Detector = Peak; 5. Trace mode = max hold; 6. Sweep = auto couple; 7. Allow the trace to stabilize; 8. The dynamic range of the spectrum analyzer at the selected RBW shall be more than 10 dB below the target “−X dB” requirement, i.e., if the requirement calls for measuring the −6 dB OBW, the spectrum analyzer noise floor at the selected RBW shall be at least 36 dB below the reference level 5.2.4.Test Setup FCC ID: 2AD8UFZMFWH201 Page Number: 13 of 50

Report No.: 1812TW0108-U1 5.2.5.Test Result Product Flexi Zone 2400 Temperature 25°C Test Engineer Kevin Ker Relative Humidity 54% Test Site SR2 Test Date 2019/04/14 Test Mode Modulation Frequency 99% 6dB Limit Result (MHz) Bandwidth(MHz) Bandwidth(MHz) (MHz) Chain D 2488.5 8.95 9.02 ≥ 0.5 Pass Band 53 QPSK 2489.0 8.94 9.01 ≥ 0.5 Pass 2490.0 8.94 9.02 ≥ 0.5 Pass 2488.5 8.94 9.00 ≥ 0.5 Pass Band 53 16QAM 2489.0 8.94 8.99 ≥ 0.5 Pass 2490.0 8.95 9.00 ≥ 0.5 Pass 2488.5 8.95 9.04 ≥ 0.5 Pass Band 53 64QAM 2489.0 8.95 9.03 ≥ 0.5 Pass 2490.0 8.95 9.02 ≥ 0.5 Pass 2488.5 8.94 9.01 ≥ 0.5 Pass Band 53 256QAM 2489.0 8.94 9.01 ≥ 0.5 Pass 2490.0 8.95 9.02 ≥ 0.5 Pass Chain M 2488.5 8.94 9.01 ≥ 0.5 Pass Band 53 QPSK 2489.0 8.95 9.02 ≥ 0.5 Pass 2490.0 8.95 9.01 ≥ 0.5 Pass 2488.5 8.95 9.03 ≥ 0.5 Pass Band 53 16QAM 2489.0 8.95 9.02 ≥ 0.5 Pass 2490.0 8.95 9.01 ≥ 0.5 Pass 2488.5 8.95 9.04 ≥ 0.5 Pass Band 53 64QAM 2489.0 8.96 9.05 ≥ 0.5 Pass 2490.0 8.94 9.02 ≥ 0.5 Pass 2488.5 8.94 9.02 ≥ 0.5 Pass Band 53 256QAM 2489.0 8.94 9.01 ≥ 0.5 Pass 2490.0 8.94 9.01 ≥ 0.5 Pass FCC ID: 2AD8UFZMFWH201 Page Number: 14 of 50

Report No.: 1812TW0108-U1 Occupied Bandwidth - Chain D (QPSK) 2488.5MHz 2489.0MHz 2490.0MHz FCC ID: 2AD8UFZMFWH201 Page Number: 15 of 50

Report No.: 1812TW0108-U1 Occupied Bandwidth - Chain D (16QAM) 2488.5MHz 2489.0MHz 2490.0MHz FCC ID: 2AD8UFZMFWH201 Page Number: 16 of 50

Report No.: 1812TW0108-U1 Occupied Bandwidth - Chain D (64QAM) 2488.5MHz 2489.0MHz 2490.0MHz FCC ID: 2AD8UFZMFWH201 Page Number: 17 of 50

Report No.: 1812TW0108-U1 Occupied Bandwidth - Chain D (256QAM) 2488.5MHz 2489.0MHz 2490.0MHz FCC ID: 2AD8UFZMFWH201 Page Number: 18 of 50

Report No.: 1812TW0108-U1 Occupied Bandwidth - Chain M (QPSK) 2488.5MHz 2489.0MHz 2490.0MHz FCC ID: 2AD8UFZMFWH201 Page Number: 19 of 50

Report No.: 1812TW0108-U1 Occupied Bandwidth - Chain M (16QAM) 2488.5MHz 2489.0MHz 2490.0MHz FCC ID: 2AD8UFZMFWH201 Page Number: 20 of 50

Report No.: 1812TW0108-U1 Occupied Bandwidth - Chain M (64QAM) 2488.5MHz 2489.0MHz 2490.0MHz FCC ID: 2AD8UFZMFWH201 Page Number: 21 of 50

Report No.: 1812TW0108-U1 Occupied Bandwidth - Chain M (256QAM) 2488.5MHz 2489.0MHz 2490.0MHz FCC ID: 2AD8UFZMFWH201 Page Number: 22 of 50

Report No.: 1812TW0108-U1 5.3. Maximum Transmit Power 5.3.1.Test Limit The maximum transmit power is no more than 1 W with a peak EIRP of no more than 6 dBw. EIRP Limit = 6 + 30 = 36 dBm 5.3.2.Test Procedure KDB 971168 D01v03r01 - Section 5.2.4 ANSI C63.26-2015 - Section 5.2.4.2 5.3.3.Test Setting Method AVGPM-G (Measurement using a gated RF average-reading power meter) Measurements may be performed using a wideband gated RF power meter provided that the gate parameters are adjusted such that the power is measured only when the EUT is transmitting at its maximum power control level. Since this measurement is made only during the ON time of the transmitter, no duty cycle correction is required. 5.3.4.Test Setup FCC ID: 2AD8UFZMFWH201 Page Number: 23 of 50

Report No.: 1812TW0108-U1 5.3.5.Test Result Product Flexi Zone 2400 Temperature 25°C Test Engineer Kevin Ker Relative Humidity 54% Test Site SR2 Test Date 2019/04/14 Test Mode Modulation Frequency Output Power (dBm) Total Power Output EIRP EIRP Limit Result (MHz) (dBm) Power Limit (dBm) (dBm) Chain D Chain M (dBm) 2488.5 26.75 26.56 29.67 ≤ 30.00 34.68 ≤ 36.00 Pass Band 53 QPSK 2489.0 26.83 26.77 29.81 ≤ 30.00 34.82 ≤ 36.00 Pass 2490.0 26.93 26.59 29.77 ≤ 30.00 34.78 ≤ 36.00 Pass 2488.5 27.00 26.66 29.84 ≤ 30.00 34.85 ≤ 36.00 Pass Band 53 16QAM 2489.0 26.66 26.74 29.71 ≤ 30.00 34.72 ≤ 36.00 Pass 2490.0 26.98 26.73 29.87 ≤ 30.00 34.88 ≤ 36.00 Pass 2488.5 26.84 26.45 29.66 ≤ 30.00 34.67 ≤ 36.00 Pass Band 53 64QAM 2489.0 26.69 26.68 29.70 ≤ 30.00 34.71 ≤ 36.00 Pass 2490.0 26.92 26.74 29.84 ≤ 30.00 34.85 ≤ 36.00 Pass 2488.5 26.67 26.40 29.55 ≤ 30.00 34.56 ≤ 36.00 Pass Band 53 256QAM 2489.0 26.79 26.51 29.66 ≤ 30.00 34.67 ≤ 36.00 Pass 2490.0 26.87 26.54 29.72 ≤ 30.00 34.73 ≤ 36.00 Pass (Chain D Average Power /10) (Chain M Average Power /10) Note 1: The Total Average Power (dBm) = 10*log{10 +10 }. NANT/Nss Note 2: EIRP (dBm) = Total Average Power (dBm) + Antenna Gain (dBi) + Array Gain (10*log( )). FCC ID: 2AD8UFZMFWH201 Page Number: 24 of 50

Report No.: 1812TW0108-U1 5.4. Power Spectral Density Measurement 5.4.1.Test Limit The maximum power spectral density conducted to the antenna is not greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission 5.4.2.Test Procedure Used KDB 971168 D01v03r01 - Section 5.4 ANSI C63.26-2015 - Section 5.2.4.5 5.4.3.Test Setting 1. Set the analyzer center frequency to the OBW center frequency 2. RBW = 3kHz 3. VBW = 10kHz 4. Sweep time = auto 5. Detector = power averaging (rms) 6. Set sweep trigger to “free run.” 7. Trace average at least 100 traces in power averaging (rms) mode if sweep is set to auto-couple. To accurately determine the average power over the on and off time of the transmitter, it can be necessary to increase the number of traces to be averaged above 100, or if using a manually configured sweep time, increase the sweep time. 8. Add 10 log (1/duty cycle) to the measured power level to compute the average power during continuous transmission. FCC ID: 2AD8UFZMFWH201 Page Number: 25 of 50

Report No.: 1812TW0108-U1 5.4.4.Test Setup FCC ID: 2AD8UFZMFWH201 Page Number: 26 of 50

Report No.: 1812TW0108-U1 5.4.5.Test Setup Product Flexi Zone 2400 Temperature 25°C Test Engineer Kevin Ker Relative Humidity 54% Test Site SR2 Test Date 2019/04/14 Test Mode Modulation Frequency PSD (dBm/3kHz) Duty Factor Total PSD Limit Result (MHz) Chain D Chain M Cycle (dBm/3kHz) (dBm/3kHz) 2488.5 -4.48 -4.52 0.22 ≤ 8.00 Pass Band 53 QPSK 2489.0 -3.91 -4.22 67.5% 1.71 0.66 ≤ 8.00 Pass 2490.0 -4.41 -4.66 0.19 ≤ 8.00 Pass 2488.5 -4.48 -4.64 0.16 ≤ 8.00 Pass Band 53 16QAM 2489.0 -4.81 -4.27 67.5% 1.71 0.19 ≤ 8.00 Pass 2490.0 -4.63 -4.59 0.11 ≤ 8.00 Pass 2488.5 -5.60 -5.90 -1.07 ≤ 8.00 Pass Band 53 64QAM 2489.0 -5.35 -5.49 68.0% 1.67 -0.74 ≤ 8.00 Pass 2490.0 -4.98 -5.41 -0.51 ≤ 8.00 Pass 2488.5 -6.18 -5.94 -1.38 ≤ 8.00 Pass Band 53 256QAM 2489.0 -5.67 -5.75 68.0% 1.67 -1.03 ≤ 8.00 Pass 2490.0 -6.04 -5.58 -1.12 ≤ 8.00 Pass (Chain D PSD /10) (Chain M PSD /10) Note: The Total PSD (dBm/3kHz) = 10*log{10 +10 } + 10*log(1/duty cycle) FCC ID: 2AD8UFZMFWH201 Page Number: 27 of 50

Report No.: 1812TW0108-U1 Power Spectral Density - Chain D (QPSK) 2488.5MHz 2489.0MHz 2490.0MHz FCC ID: 2AD8UFZMFWH201 Page Number: 28 of 50

Report No.: 1812TW0108-U1 Power Spectral Density - Chain D (16QAM) 2488.5MHz 2489.0MHz 2490.0MHz FCC ID: 2AD8UFZMFWH201 Page Number: 29 of 50


Document Created: 2019-06-17 16:38:58
Document Modified: 2019-06-17 16:38:58
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC