RF Exposure

FCC ID: 2AD7Z-K40

RF Exposure Info

Download: PDF
FCCID_4437606

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.                                                            FCC ID: 2AD7Z-K40

                                        FCC RF Exposure Evaluation
         1. Product Information

           FCC ID:                                     2AD7Z-K40
           Product name                                Bluetooth Speaker
           Model number                                K40, A60A, A60C, A60S
                                                       PCB board, structure and internal of these model(s) are
           Model Declaration
                                                       the same, So no additional models were tested.
           Test Model                                  K40
           Power supply                                DC 5V 1A
           Modulation Type                             GFSK, π/4-DQPSK for Bluetooth V5.0 (BDR/EDR)
           Antenna Type                                PCB antenna
           Antenna Gain                                0dBi (maximum)
           Hardware version                            /
           Software version                            /
           Bluetooth Operation frequency               2402MHz-2480MHz
           Bluetooth Version                           V5.0
           Exposure category                           General population/uncontrolled environment
           EUT Type                                    Production Unit
           Device Type                                 Portable Device

         2. Evaluation Method

          According to KDB447498 D01 General RF Exposure Guidance v06Section 4.3.1 Standalone SAR test
          exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures,
          standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure
          conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test
          Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on
          source-based time-averaged maximum conducted output power of the RF channel requiring evaluation,
          adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure
          conditions. The minimum test separation distance is determined by the smallest distance from the
          antenna and radiating structures or outer surface of the device, according to the host form factor,
          exposure conditions and platform requirements, to any part of the body or extremity of a user or
          bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied
          must be fully explained and justified by the operating configurations and exposure conditions of the
          transmitter and applicable host platform requirements, typically in the SAR measurement or SAR
          analysis report, according to the required published RF exposure KDB procedures. When no other RF
          exposure testing or reporting is required, a statement of justification and compliance must be included
          in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When
          required, the device specific conditions described in the other published RF exposure KDB procedures
          must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT
          two-way radios, handsets, laptops & tablets etc.“
          [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)+ · *√f
          (GHz)+ ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where:
          • f (GHz) is the RF channel transmit frequency in GHz
          • Power and distance are rounded to the nearest mW and mm before calculation
          • The result is rounded to one decimal place for comparison
          • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below
           The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for
           transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is
           < 5 mm, a distance of 5 mm according to f) in section 4.1 is applied to determine SAR test exclusion.

           When one of the following test exclusion conditions is satisfied for all combinations of simultaneous
           transmission configurations, further equipment approval is not required to incorporate transmitter
           modules in host devices that operate in the mixed mobile and portable host platform exposure


   This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
                                                                  Page 1 of 3


SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.                                                            FCC ID: 2AD7Z-K40

           conditions. The grantee is responsible for documenting this according to Class I permissive change
           requirements. Antennas that qualify for standalone SAR test exclusion must apply the estimated
           standalone SAR to determine simultaneous transmission test exclusion.
           a) The *∑ of (the highest measured or estimated SAR for each standalone antenna configuration,
               adjusted for maximum tune-up tolerance) / 1.6 W/kg+ + *∑ of MPE ratios+ is ≤ 1.0.
           b) The SAR to peak location separation ratios of all simultaneously transmitting antenna pairs
               operating in portable device exposure conditions are all ≤ 0.04, and the *∑ of MPE ratios+ is ≤ 1.0.

         3. Refer Evaluation Method

             ANSI C95.1–1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency
             Electromagnetic Fields, 3 kHz to 300 GHz.
             FCC KDB publication 447498 D01 General RF Exposure Guidance v06: Mobile and Portable Devices RF
             Exposure Procedures and Equipment Authorization Policies.
             FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits.
             FCC CFR 47 part2 2.1093: Radiofrequency radiation exposure evaluation: portable devices

         4. Conducted Power Results

                                                           [BT Classics]
                    Mode              Channel            Frequency              Peak Conducted Output Power
                                                           (MHz)                          (dBm)
                                           0                2402                               -1.919
                     GFSK                 39                2441                               -0.705
                                          78                2480                                0.944
                                           0                2402                               -1.301
                  π/4DQPSK                39                2441                                0.007
                                          78                2480                                1.616




         5. Manufacturing Tolerance

                                                        [BT Classics]
                                                         GFSK (Peak)
                  Channel                      Channel 0            Channel 39                           Channel 78
               Target (dBm)                      -1.0                  0.0                                  0.0
              Tolerance ±(dB)                     1.0                  1.0                                  1.0
                                                      π/4DQPSK (Peak)
                  Channel                      Channel 0            Channel 39                           Channel 78
               Target (dBm)                      -1.0                  0.0                                  1.0
              Tolerance ±(dB)                     1.0                  1.0                                  1.0




                                                                   [




   This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
                                                                  Page 2 of 3


SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD.                                                            FCC ID: 2AD7Z-K40



         6.    Evaluation Results

         6.1     Standalone Evaluation

                                       Antenna Distance           RF output power          SAR Test Exclusion        SAR Test
         Band/Mode          f (GHz)
                                            (mm)                  dBm         mW               Threshold             Exclusion
            GFSK             2.480            5                    1         1.259            0.397 < 3.0               Yes
          π/4DQPSK           2.480            5                    2         1.585            0.499 < 3.0               Yes

         Remark:
          1. RF output power including tune up tolerance;
          2. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to f) in section 4.1
              of KDB 447498 is applied to determine SAR test exclusion.


         6.2 Simultaneous Transmission for SAR Exclusion

               The sample support one BT modular and one antenna, no need consider simultaneous transmission;

         7.     Conclusion

            The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure
            and SAR Exclusion Threshold per KDB 447498 v06.

                                 ----------------THE END OF REPORT---------------




   This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
                                                                  Page 3 of 3



Document Created: 2019-09-04 13:55:43
Document Modified: 2019-09-04 13:55:43

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC