Test Report

FCC ID: 2ACYT-BNL15X7

Test Report

Download: PDF
FCCID_2803695

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Nanshan District Shenzhen, China 518057 Telephone: +86 (0) 755 2601 2053 Report No.: SZEM150700425801 Fax: +86 (0) 755 2671 0594 Page: 1 of 21 Email: ee.shenzhen@sgs.com TEST REPORT Application No.: SZEM1507004258CR Applicant: SHENZHEN Hitevision Technology Co., Ltd. Address of Applicant: No. 8, Qinglan 1st Road, Pingshan, Shenzhen, Guangdong 518118, P. R. China. Manufacturer: Newline Interactive Inc. Address of Manufacturer: 101 East Park Blvd. Suite 807 Plano, TX 75074, USA Factory: SHENZHEN Hitevision Technology Co., Ltd. Address of Factory: No. 8, Qinglan 1st Road, Pingshan, Shenzhen, Guangdong 518118, P. R. China. Equipment Under Test (EUT): EUT Name: Collaboration Touch Screen Model No.: X7, X7-x, X7-xx, X7-xxx (x =0-9, a-z or A-Z) ♣ ♣ Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical FCC ID: 2ACYT-BNL15X7 Standards: 47 CFR PART 15,Subpart B:2014 Date of Receipt: 2015-07-20 Date of Test: 2015-08-10 to 2015-08-18 Date of Issue: 2015-09-29 Test Result : Pass* * In the configuration tested, the EUT complied with the standards specified above. Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 2 of 21 2 Test Summary Item Standard Method Class Result Conducted Disturbance at Mains 47 CFR PART ANSI C63.4 Class B Pass Terminals 15,Subpart B:2014 (150kHz-30MHz) Radiated Disturbance 47 CFR PART ANSI C63.4 Class B Pass (30MHz-1GHz) 15,Subpart B:2014 Radiated Disturbance 47 CFR PART ANSI C63.4 Class B Pass (above 1GHz) 15,Subpart B:2014 The highest frequency of the Upper frequency of measurement Range internal sources of the EUT Below 1.705MHz 30MHz 1.705MHz to 108MHz 1GHz 108MHz to 500MHz 2GHz 500MHz to 1GHz 5GHz Above 1GHz 5th harmonic of the highest frequency or 40GHz, whichever is lower Remark: Model No.: X7, X7-x, X7-xx, X7-xxx (x =0-9, a-z or A-Z) Only the model X7 was tested, since the electrical circuit design, layout, components used and internal wiring were identical for the above models, only different on outlook silkprint, color and model number. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 3 of 21 3 Contents Page 1 COVER PAGE ............................................................................................................................................1 2 TEST SUMMARY .................................................................................................................................................... 2 3 CONTENTS .............................................................................................................................................................. 3 4 GENERAL INFORMATION .................................................................................................................................... 4 4.1 DETAILS OF E.U.T. ................................................................................................................................................. 4 4.2 DESCRIPTION OF SUPPORT UNITS ............................................................................................................................ 4 4.3 STANDARDS APPLICABLE FOR TESTING .................................................................................................................. 5 4.4 TEST LOCATION ...................................................................................................................................................... 6 4.5 TEST FACILITY ........................................................................................................................................................ 6 4.6 DEVIATION FROM STANDARDS................................................................................................................................ 6 4.7 ABNORMALITIES FROM STANDARD CONDITIONS .................................................................................................... 6 5 EQUIPMENT LIST ................................................................................................................................................... 7 6 EMISSION TEST RESULTS .................................................................................................................................. 9 6.1 CONDUCTED DISTURBANCE AT MAINS TERMINALS(150KHZ-30MHZ)................................................................... 9 6.1.1 E.U.T. Operation ........................................................................................................................................ 9 6.1.2 Test Setup................................................................................................................................................. 10 6.1.3 Measurement Data .................................................................................................................................. 10 6.2 RADIATED DISTURBANCE(30MHZ-1GHZ) ........................................................................................................... 13 6.2.1 E.U.T. Operation ...................................................................................................................................... 13 6.2.2 Measurement Data .................................................................................................................................. 13 6.3 RADIATED DISTURBANCE(ABOVE 1GHZ) ............................................................................................................. 16 6.3.1 E.U.T. Operation ...................................................................................................................................... 16 6.3.2 Measurement Data .................................................................................................................................. 16 7 PHOTOGRAPHS ................................................................................................................................................... 19 7.1 CONDUCTED DISTURBANCE AT MAINS TERMINALS(150KHZ-30MHZ) TEST SETUP ............................................. 19 7.2 RADIATED DISTURBANCE(30MHZ-1GHZ) TEST SETUP........................................................................................ 19 7.3 RADIATED DISTURBANCE(ABOVE 1GHZ) TEST SETUP ......................................................................................... 20 7.4 EUT CONSTRUCTIONAL DETAILS ......................................................................................................................... 21 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 4 of 21 4 General Information 4.1 Details of E.U.T. Power Supply: Input voltage: AC100-240V 50/60Hz Test voltage: AC120V 60Hz DC 3V (1.5V x 2"AAA"Size batteries) for remote control Cable: AC cable:180cm unshielded USB cable:500cm shielded with two ferrite core HDMI cable:295cm shielded Internal source Above 1GHz 4.2 Description of Support Units Description Manufacturer Model No. Laptop Lenovo T430u Mouse Lenovo MO28UOA MITSUBISHI Television MITSUBISHI AX025 U-disk Color turn UL4GHKXG Router NETGEAR DGN2200 Router NETGEAR JNR3300 SD Card Kingston SD-K08G Earphone PHILIPS SHE6000 AUX IN Cable SAMZHE YPH-8310 HDMI Cable Supplied by SGS REF. No.SEA0900 VGA Cable Supplied by SGS REF. No.SEA3300 Network Cable Supplied by SGS REF. No.SEA1100 X-PC(OPS port load) Supplied by client XJ-0581 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150r00425e01 Page S of21 4.3 Standards Applicable for Testing "Table 1 Tests Garried Out Under 47 CFR. PART 15.Subport Bra0re Method htem Status ansicosa Condscted Disurbanceat Mains Terminals / pisoute—coutHe ansicssa Rediated Disturbance(@MHe—1GHe) / Anslossa Redated Disturbance(cbove 1GHz / x Incleates tratthetosis not applcable Y Indeates tratthetest is appleable

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 6 of 21 4.4 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch E&E Lab, No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Shenzhen, Guangdong, China. 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. 4.5 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 10m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-823, R-4188, T-1153 and C-2383 respectively. • FCC – Registration No.: 556682 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 556682. • Industry Canada (IC) The 3m Semi-anechoic chambers and the 10m Semi-anechoic chambers of SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-2, 4620C-3. 4.6 Deviation from Standards None 4.7 Abnormalities from Standard Conditions None This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 7 of 21 5 Equipment List Conducted Disturbance at Mains Terminals(150kHz-30MHz) Inventory Cal. date Cal Due Item Equipment Manufacturer Model No No (yyyy-mm-dd) Date ChangZhou 1 Shielding Room GB-88 SEL0042 2015-05-13 2016-05-13 ZhongYu 2 LISN Rohde & Schwarz ENV216 SEL0152 2015-10-09 2016-10-09 3 LISN ETS-LINDGREN 3816/2 SEL0021 2015-05-13 2016-05-13 4 EMI Test Receiver Rohde & Schwarz ESCI SEL0022 2015-05-13 2016-05-13 5 Coaxial Cable SGS N/A SEL0025 2015-05-13 2016-05-13 Radiated Disturbance Inventory Cal. date Cal Due Item Equipment Manufacturer Model No No (yyyy-mm-dd) Date 10m Semi-Anechoic 1 SAEMC FSAC1018 SEL0303 2015-08-01 2016-08-01 Chamber 2 EMI Test Receiver Rohde & Schwarz ESR SEL0295 2015-05-13 2016-05-13 3 EMI Test software AUDIX E3 SEL0050 N/A N/A 4 Coaxial cable SGS N/A SEL0288 2015-05-13 2016-05-13 5 Coaxial cable SGS N/A SEL0275 2015-05-13 2016-05-13 6 Coaxial cable SGS N/A SEL0274 2015-05-13 2016-05-13 BiConiLog 7 Schwarzbeck VULB9160 SEL0308 2015-10-17 2018-10-17 Antenna(30M-1GHz) BiConiLog 8 Schwarzbeck VULB9160 SEL0309 2015-10-17 2018-10-17 Antenna(30M-1GHz) Horn Antenna(1- 9 Rohde & Schwarz HF907 SEL0310 2015-06-14 2018-06-14 18GHz) Sonoma Instrument 10 Pre-amplifier 310N SEL0298 2015-05-13 2016-05-13 Co This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 8 of 21 General used equipment Cal. date Cal.Due date Item Equipment Manufacturer Model No Inventory No (yyyy-mm-dd) (yyyy-mm-dd) Shang Hai Humidity/Temperature 1 Meteorological ZJ1-2B SEL0101 2015-10-12 2016-10-12 Indicator Industry Factory Shang Hai Humidity/Temperature 2 Meteorological ZJ1-2B SEL0102 2015-10-12 2016-10-12 Indicator Industry Factory Shang Hai Humidity/Temperature 3 Meteorological ZJ1-2B SEL0103 2015-10-12 2016-10-12 Indicator Industry Factory Chang Chun 4 Barometer Meteorological DYM3 SEL0088 2015-05-13 2016-05-13 Industry Factory This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 9 of 21 6 Emission Test Results 6.1 Conducted Disturbance at Mains Terminals(150kHz-30MHz) Test Requirement: 47 CFR PART 15,Subpart B:2014 Test Method: ANSI C63.4 Frequency Range: 150kHz to 30MHz Limit: 0.15M-0.5MHz 66dB(µV)-56dB(µV) quasi-peak, 56dB(µV)-46dB(µV) average 0.5M-5MHz 56dB(µV) quasi-peak, 46dB(µV) average 5M-30MHz 60dB(µV) quasi-peak, 50dB(µV) average Detector: Peak for pre-scan (9kHz resolution bandwidth) 0.15M to 30MHz 6.1.1 E.U.T. Operation Operating Environment: Temperature: 23.0 °C Humidity: 54 % RH Atmospheric Pressure: 1010 mbar a:HDMI1 mode: Keep EUT working with external HDMI source via front panel HDMI port and HDMI signal output via rear panel HDMI port. b: HDMI2 mode: Keep EUT working with external HDMI source via rear panel HDMI rear port and HDMI signal output via rear panel HDMI port. c: LAN mode: Build the connection between EUT and internet, Keep EUT working with external internet source. Pretest these d: VGA and Audio in mode: Set the brightness and contrast to the maximum. Kept displaying character "H" in all screen. Set character size and number of characters mode to find per line so that typically the greatest number of characters per screen is displayed. e:SD card mode : Keep EUT playing with SD card. the worst case: f:USB mode :Keep EUT working with 1-8 USB ports, pretest at each ports to find the worst case. g:Top camera mode: Keep EUT recording via top camera. h::Bottom camera mode: Keep EUT recording via bottom camera. i: MIC record mode:Keep EUT recording via micphone. j: Normally working mode, keep EUT working normally. a:HDMI1 mode: Keep EUT working with external HDMI source via front panel HDMI The worst case port and HDMI signal output via rear panel HDMI port. for final test: This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 10 of 21 6.1.2 Test Setup 6.1.3 Measurement Data An initial pre-scan was performed with peak detector.Quasi-Peak or Average measurement were performed at the frequencies with maximized peak emission were detected. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 11 of 21 Mode:a;Line:Live Line This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 12 of 21 Mode:a;Line:Neutral Line This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 13 of 21 6.2 Radiated Disturbance(30MHz-1GHz) Test Requirement: 47 CFR PART 15,Subpart B:2014 Test Method: ANSI C63.4 Frequency Range: 30MHz to 1GHz Limit: 30MHz -88MHz 29.5(dBµV/m) quasi-peak 88MHz-216MHz 33.0(dBµV/m) quasi-peak 216MHz-960MHz 35.6(dBµV/m) quasi-peak 960MHz-1000MHz 44.4(dBµV/m) quasi-peak Detector: Peak for pre-scan (120kHz resolution bandwidth) 30M to1000MHz 6.2.1 E.U.T. Operation Operating Environment: Temperature: 23.0 °C Humidity: 56 % RH Atmospheric Pressure: 1010 mbar a:HDMI1 mode: Keep EUT working with external HDMI source via front panel HDMI port and HDMI signal output via rear panel HDMI port. b: HDMI2 mode: Keep EUT working with external HDMI source via rear panel HDMI rear port and HDMI signal output via rear panel HDMI port. c: LAN mode: Build the connection between EUT and internet, Keep EUT working with external internet source. Pretest these d: VGA and Audio in mode: Set the brightness and contrast to the maximum. Kept displaying character "H" in all screen. Set character size and number of characters mode to find per line so that typically the greatest number of characters per screen is displayed. e:SD card mode : Keep EUT playing with SD card. the worst case: f:USB mode :Keep EUT working with 1-8 USB ports, pretest at each ports to find the worst case. g:Top camera mode: Keep EUT recording via top camera. h::Bottom camera mode: Keep EUT recording via bottom camera. i: MIC record mode:Keep EUT recording via micphone. j: Normally working mode, keep EUT working normally. a:HDMI1 mode: Keep EUT working with external HDMI source via front panel HDMI The worst case port and HDMI signal output via rear panel HDMI port. for final test: 6.2.2 Measurement Data An initial pre-scan was performed in the chamber using the spectrum analyser in peak detection mode. Quasi-peak measurements were conducted based on the peak sweep graph. The EUT was measured by BiConiLog antenna with 2 orthogonal polarities. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 14 of 21 Mode:a;Polarization:Horizontal This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 15 of 21 Mode:a;Polarization:Vertical This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 16 of 21 6.3 Radiated Disturbance(above 1GHz) Test Requirement: 47 CFR PART 15,Subpart B:2014 Test Method: ANSI C63.4 Frequency Range: Above 1GHz Limit: Above 1GHz 74(dBµV/m) peak, 54(dBµV/m) average Detector: Peak for pre-scan (1000kHz resolution bandwidth) 1000M to18000MHz 6.3.1 E.U.T. Operation Operating Environment: Temperature: 23.0 °C Humidity: 56 % RH Atmospheric Pressure: 1010 mbar a:HDMI1 mode: Keep EUT working with external HDMI source via front panel HDMI port and HDMI signal output via rear panel HDMI port. b: HDMI2 mode: Keep EUT working with external HDMI source via rear panel HDMI rear port and HDMI signal output via rear panel HDMI port. c: LAN mode: Build the connection between EUT and internet, Keep EUT working with external internet source. Pretest these d: VGA and Audio in mode: Set the brightness and contrast to the maximum. Kept displaying character "H" in all screen. Set character size and number of characters mode to find per line so that typically the greatest number of characters per screen is displayed. e:SD card mode : Keep EUT playing with SD card. the worst case: f:USB mode :Keep EUT working with 1-8 USB ports, pretest at each ports to find the worst case. g:Top camera mode: Keep EUT recording via top camera. h::Bottom camera mode: Keep EUT recording via bottom camera. i: MIC record mode:Keep EUT recording via micphone. j: Normally working mode, keep EUT working normally. a:HDMI1 mode: Keep EUT working with external HDMI source via front panel HDMI The worst case port and HDMI signal output via rear panel HDMI port. for final test: 6.3.2 Measurement Data An initial pre-scan was performed in the chamber using the spectrum analyser in peak detection mode. Average measurements were conducted based on the peak sweep graph. The EUT was measured by BiConiLog antenna with 2 orthogonal polarities. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 17 of 21 Mode:a;Polarization:Horizontal This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 18 of 21 Mode:a;Polarization:Vertical This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 19 of 21 7 Photographs 7.1 Conducted Disturbance at Mains Terminals(150kHz-30MHz) Test Setup 7.2 Radiated Disturbance(30MHz-1GHz) Test Setup This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 20 of 21 7.3 Radiated Disturbance(above 1GHz) Test Setup This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM150700425801 Page: 21 of 21 7.4 EUT Constructional Details Refer to Appendix A - Photographs of EUT Constructional Details for SZEM1507004258CR. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only


Document Created: 2015-11-04 01:33:41
Document Modified: 2015-11-04 01:33:41
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC