UM

FCC ID: 2ACXH-F10

Users Manual

Download: PDF
FCCID_4483787

材质：128g书写纸 A 印刷：单色双面印刷 尺寸：见图档标注 折叠方式:风琴页折叠 100mm 100mm 3 Vol + 4 Previous song Forced pairing 2 Next song 1 Vol - Play / pause Answer call On / Off Refuse call LED light / MIC AUX in Micro USB HOW TO USE 150mm 1. General function Operation LED Status Power on Blue LED flashes 3 times Power off Red LED flashes 1 second Pairing Red LED & Blue LED flashes alternately Standby Blue LED flashes 1 times in 5 seconds Low battery Red LED flashes Charging Red LED keep lighting during charging Blue LED keep lighting when charging finished 2. Basic Buttons Operation Power on: Push button to on side. Blue LED flashes 3 times. Headphone turn on. Ｆ１０ Power off: Push button to off side. Red LED turn off after flashes 1 times. Headphone turn off. Ｕｓｅｒ Ｍａｎｕａｌ Paring: After power on, the headphone will be entered into pairing mode automatically. Red LED & Blue LED flashes alternately. if not, long press 4 ' Previous song' button for 3s to enter paring mode. Volume adjust: Long press on 3 buttons,one level voice volume changes. SPECIFICATION When volume reaches to Max or Minimum, "Di" reminding voice occurs. Play / Pause: Short press 1 button, music pause. Press it again, music Talk time: 20h continues. Standby: 0.5mA Previous: In playback status, press 4 button, music turns to previous one. Battery: 400mAh Next: In playback status, press 2 button, music turns to next one. Standby time: 750h Answer Call: Short press 1 button to answer the phone call. Charging time: 3~4h End call: Short press 1 button, phone call ended. IC solution: QCC3005 Reject call: Long Press 1 button for 2 seconds to reject a call. Bluetooth: 5.0 Battery Capacity status: When headphone connects to iOS devices, Charging voltage: 5.0V iOS devices show the headphone battery power status on the upper right Wireless range: ≥10m corner. BT music play time: 20h Charging: new headphone has enough power for pairing and dialing Power voltage: 3.0~4.2V out for several times. When in low battery, please charging via USB cable Speaker: φ40mm 32Ω ±15% for 3~4 hours. Red LED keep lighting during charging, blue LED keep lighting Transmission power: CLASS 2 charging finished. Transmission frequency: 2.4G Reset Mode: Connect the headphone to computer via Micro USB cable. Bluetooth: HSP / HFP / A2DP / AVRCP / SBC / AAC / APTX / PATXLL When red LED light on, headphone reset finished. Sound pressure level (Sensitivity): 108±3dB At 1kHz 1mw / IE 3.5mm music line-in function: Connect Audio line in cable to 3.5 audio jack for wired music. Phone call function cannot be used in this mode. KIT CONTENTS Headphone will be powered off after insert 3.5mm line-in cable. 1. Stereo Bluetooth headphone x 1 3.5MM AUDIO JACK 2. Charging Micro USB Cable x 1 3. User Manual x 1 1. Connect the 3.5 audio wire to the headphone and audio player. 4. 3.5mm audio wire x 1 2. You can adjust volume bottom of the audio player or the mobile phone to reach right volume to listen music. WARNING FEATURES 1. You must choose a qualified charger from a regular manufacturer to charge the headphone. 1. Bluetooth 5.0 2. You must charge the headphone if it has not been used for more 2. 3.5mm music line-in function than 12 months. 3. iOS show the headphone battery power status

FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.


Document Created: 2019-10-18 19:30:49
Document Modified: 2019-10-18 19:30:49
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC