Users Manual

FCC ID: 2ACVD05601045

Users Manual

Download: PDF
FCCID_2679699

testo 104-IR BT Combined infrared and penetration thermometer with Bluetooth® n a r y pre limi Instruction manual en

2 1. General information 3 1. General information de Please read this document through carefully and familiarize yourself with the operation of the product before putting it to use. en Keep this document to hand so that you can refer to it when necessary. fr 2. Safety information es preliminary Avoid electrical hazards: it Do not conduct measurements on or near live parts! pt Adhere to the product safety/warranty requirements: Always operate the instrument properly and according to its sv intended purpose and within the parameters specified. Do not use force. nl Do not store with solvents (e.g. acetone). Only open the instrument if this is expressly described in the ?? documentation for the purpose of maintenance or repair work. ?? Ensure correct disposal: Dispose of defective rechargeable batteries and spent batteries at the collection points provided. Send the instrument directly to us at the end of its life cycle. We will ensure that it is disposed of in an environmentally friendly manner. 3. Intended use The testo 104-IR BT is a robust food thermometer. The product is designed for the following tasks/areas: · Food sector: production, food service, spot check measurement, incoming goods. · Measuring liquids, pastes and semi-solid materials The following product components are designed for continuous contact with foodstuffs in accordance with Regulation (EC) 1935/2004: The immersion/penetration probe from the tip up to 2 cm before the probe handle or the plastic housing. If provided, information about penetration depths in the instruction manual or the mark(s) on the immersion/penetration probe should be observed. The product should not be used in the following areas: · Potentially explosive areas · For diagnostic measurements in the medical sector

4 4. Technical data 5. Product description 5 4. Technical data 4.2 General Technical data de Feature Values 4.1 Bluetooth Modul Penetration probe en Sensor type NTC The Bluetooth® option may only be operated in countries in Measuring range -50 to +250 °C / -58 to +482 °F which it is type approved. Resolution 0.1 °C/°F/°R fr preliminary Feature Values Accuracy (±1 digit) ±1.0 °C / ±1.8 °F (-50,0 to-30,1°C / -58.0 to -22.1 °F) Bluetooth Range >20 m (free field) ±0.5 °C / ±0.9 °F (-30,0 to +99,9°C / -22.0 to +211.9 °F) ±1 % of the measuring range (+100.0 to +250.0 °C / +212.0 es luetooth type LSD Science & Technology Co., Ltd L Series BLE Module (08 Mai 2013) based on TI CC254X chip to +482.0 °F) Qualified Design ID B016552 Response time t99 10 s (measured in moving liquid) Bluetooth radio class Class 3 Measuring rate 0.5 s it Bluetooth company 10274 Infrared measurement Lens 10:1 + opening diameter of the sensor (12 mm / 0.47”) pt Certification Spectral range 8 to 14 μm Belgium (BE), Bulgaria (BG), Denmark (DK), Germany (DE), Laser type 2-point laser Output / wavelength < 1 mW / 650nm sv Estonia (EE), Finland (FI), France (FR), Greece (GR), Ireland (IE), Class / standard 2 / DIN EN 60825-1:2007 Italy (IT), Latvia (LV), Lithuania (LT), Luxembourg (LU), Malta Measuring range -30 - +250 °C / -22 - +482 °F (MT), Netherlands (NL), Austria (AT), Poland (PL), Portugal (PT), Resolution 0.1 °C/°F/°R nl Romania (RO), Sweden (SE), Slovakia (SK), Slovenia (SI), Spain Accuracy (at 23°C, ±1 digit) ±2.5 °C / ±4.5 °F (-30.0 to -20.1 °C / -22.0 to -4.2 °F) ±2.0 °C / ±3.6 °F (-20.0 to -0.1 °C / -4.1 to 31.9 °F) (ES), Czech Republic (CZ), Hungary (HU), United Kingdom (GB), ?? ±1.5 °C / ±2.7 °F or ±1.5 % of the measuring value (0.0 to Republic of Cyprus (CY). +250.0 °C / +32.0 to +482.0 °F) Measuring rate 0.5 s EFTA countries ?? General Norway and Switzerland. Operating temperature -20 to +50 °C / -4 to +122 °F Other countries Transportation/ -30...+70 °C / -22 to +158 °F (without batteries) storage temperature USA, Canada, Turkey, Australia, New Zealand, South Korea, Power supply 2 x AAA batteries India, Russia, Japan Battery life 10 h (typical at 25°C / 77°F) Housing ABS/TPE/PC and die-cast zinc/stainless steel Information from the FCC (Federal Communications Protection class IP65 Commission) Dimensions 281 x 48 x 21 mm / 11.06 x 1.89 x 0.83“ (immersion/ This device complies with part 15 of the FCC Rules. penetration probe folded out) 178 x 48 x 21 mm / 7.01 x 1.89 x 0.83” Commissioning is subject to the two following conditions: (1) This (immersion/penetration probe folded up) instrument must not cause any harmful interference and (2) this Weight 210g / 0.433lbs (incl. batteries) instrument must be able to cope with interference, even if this has Standards EN 13485 EC Directive 2004/108/EC undesirable effects on operation. Warranty 2 years, warranty terms: see www.testo.com/warranty Changes The FCC demands that the user be informed that any changes or Information on standards This product complies with the EN 13485 standard for modifications to the instrument that are not explicitly approved by penetration measurement. Testo AG may void the user’s right to use this instrument. Suitability: S, T (storage, transportation) Environment: E (transportable thermometer) Accuracy class: 0.5 Measuring range: -50...+250 °C According to EN 13485, the measuring instrument should be checked and calibrated regularly under the terms of EN 13486 (recommended frequency: yearly). Contact us for more information.

6 7. Operation 8. Settings 7 5. Product description 7. Operation de 1 Infrared sensor 7.1 Switching on/off en 2 2-point laser 3 Display Switching on via fold-out probe fr 4 Control keys: preliminary Fold out the probe. · [ON]: switches the instrument on - All display segments light up briefly. Contact measurement is es · [OFF]: switches the instrument off enabled ( lights up). (hold button down) · [ ]: switches to IR measurement, Switching on/off via control keys it carry out IR measurement (hold button Switch the instrument on: press [ON]. down) - All display segments light up briefly. IR measurement is pt · [ ]: switches to contact measurement enabled ( lights up). · [HOLD/MIN/MAX]: holds measuring Switch off the instrument: press and hold down [OFF] until the sv value, displays minimum/maximum display goes off. value, sends data to mobile device The instrument switches off automatically if no key is pressed: nl (Bluetooth) for 10 minutes when the probe is folded out, or for 1 minute 5 Fold-out immersion/penetration probe, when the probe is folded up. ?? folding out the probe switches the instrument on 7.2 Changing the measuring mode ?? 6 Battery compartment (at the back) Contact measurement —> IR measurement: press [ ]. IR measurement —> contact measurement: press [ ]. 7.3 Measuring Observe the information on IR measurement/contact 6. Commissioning measurement (see chapter below). Inserting batteries Bluetooth mode Cnl1 (Controlled Mode) is enabled: Display shows bLE, all buttons are locked, instrument can be 1 Use a slotted screwdriver to undo the controlled by external mobile device only. screw on the battery compartment. IR measurement 2 Open the battery compartment. - Instrument is on, IR measurement is enabled, Bluetooth mode 3 Insert batteries (2x type AAA). Observe Cnl2 (Autonomous Mode) is enabled. the polarity! 1 Start measurement: press and hold down [ ]. 4 Close the battery compartment. 2 Lock in on measurement object using the laser points: laser points mark the edges of the measuring range. 5 Tighten the screw. - The current measuring value is displayed. 3 End measurement: release the key. - Hold lights up. The last measuring value and min./max. value are saved until the next measurement, or until the instrument is switched off. 4 Send data to mobile device: press [HOLD / MIN / MAX]. Switch between min., max. and recorded value: press [HOLD / MIN / MAX].

8 9. Service and maintenance 11. Information on infrared (IR) measurement 9 The min./max. values can be reset: 5 Select Bluetooth mode Cnl1 (Controlled Mode) oder Cnl2 de (Autonomous Mode): press [ ] or [ ]. · press [ ] or switch the instrument off. - The instrument switches to IR measurement. Restart measurement: press and hold down [ ]. en Setting the emission level: 9. Service and maintenance · When IR measurement is enabled, press and hold down[ ] fr preliminary and [ ] at the same time ( lights up). 9.1 Changing the batteries · Emission level is displayed. 1 Use a slotted screwdriver to undo the es · Use [ ] or [ ] to change the value and wait for 3 s. screw on the battery compartment. Contact measurement 2 Open the battery compartment. it - Instrument is on, contact measurement is enabled ( lights up), Bluetooth mode Cnl2 (Autonomous Mode) is enabled. 3 Insert batteries (2x type AAA). Observe pt 1 Position the contact thermometer in the measurement object the polarity! and initiate the measurement: press [ ]. 4 Close the battery compartment. 2 End measurement: press [HOLD / MIN / MAX]. sv 5 Tighten the screw. - Hold lights up. The last measuring value and min./max. value are saved until the next measurement, or until the instrument is 9.2 Cleaning the instrument nl switched off. Only use weak, commercially available neutral/household cleaning AutoHold function: if this function is enabled, the measurement agents (e.g. washing-up liquid) to clean the instrument. Do not ?? is ended automatically as soon as the measuring value is use aggressive cleaning agents or solvent! stable, AutoHold lights up. ?? The housing and probe can be disinfected using an alcohol- 4 Send data to mobile device: press [HOLD / MIN / MAX]. based spray. In doing so, always follow the manufacturer’s Switch between min., max. and recorded value: instructions. press [HOLD / MIN / MAX]. Clean the housing and probe under running water and rub dry The min./max. values can be reset: with a towel. · switch the instrument off, switch to IR measurement or, while Clean the lens carefully with a cotton bud dipped in water or the held measuring value is displayed (Hold lights up), press medical alcohol. and hold down [HOLD / MIN / MAX] until Clr lights up. Restart measurement: press [ ]. 10. Questions and answers 8. Settings Question lights up Possible causes Low battery Possible solution Change batteries. - The instrument is switched off. IR measurement: Measuring values Keep to permissible - - - lights up. outside measuring range measuring range. If no button is pressed for 3 s in settings mode, the instrument Contact measurement: Valores de medición Keep to measuring - - - lights. outside permissible range range. switches to the next view. Instrument cannot Batteries dead. Change batteries. 1 Press and hold down [ ] and [ ] until AutoHold or Hold be switched on flashes. Instrument Instrument switches off Switch the switches itself off. automatically after 10 min instrument on again 2 Switch the AutoHold function on (AutoHold) or off (Hold): press in contact measurement mode [ ] or [ ]. and after 1 min after switching on in IR measurement mode. - °C, °F or °R flashes. 3 Set measurement unit to degrees Celsius (°C), degrees Fahrenheit (°F) or degrees Réaumur (°R): press [ ] or [ ]. If we have not been able to answer your question, please contact - flashes. your local dealer or Testo Customer Service. For contact details, 4 Switch the laser on (on) or off (oFF): press [ ] or [ ]. please visit www.testo.com/service-contact.

10 12. Information on contact measurement 11 11. Information on infrared (IR) 11.3 Measuring range, distance de measurement Depending on the distance of the measuring instrument from the measurement object, a specific measuring range is recorded. en 11.1 Measuring method Measuring lens (ratio of distance : measuring range) In italics = laser IR measurement is a visual measurement Not in italics = measuring range fr preliminary Keep lens clean. Do not carry out measurement with a foggy lens. es Keep the measuring range (the range between the instrument and the measurement object) free of obstacles. There must be no particles of dust or dirt, no humidity (rain, steam) and no it gases. IR measurement is a surface measurement pt If there is dirt, dust, frost, etc. on the surface, only the outermost layer is measured, i.e. the dirt. sv For vacuum-packed food, do not measure at air pockets. Where the values are critical, always measure separately nl with a contact thermometer. Particularly in the food sector: measure core temperature with a penetration/immersion * Optimised measuring distance ?? thermometer. Adjustment time 12. Information on contact ?? If the ambient temperature changes (change of location, e.g. measurement indoors/outdoors), the instrument must be measurement allowed to equalise for 15 minutes for infrared measurement. Observe the minimum penetration depth for immersion/ penetration probes: 11.2 Emissivity 10x probe diameter Materials have different emission levels. This means they emit Avoid using in aggressive acids or alkalis. various amounts of electromagnetic radiation. The emission level of the instrument has a default setting of 0.95. This is ideal for the measurement of food, non-metals (paper, ceramic, gypsum, wood, paints and varnishes) and plastics.

preliminary www.testo.com testo AG Postfach 11 40, 79849 Lenzkirch Testo-Straße 1, 79853 Lenzkirch Telefon: (0 76 53) 6 81 - 0 Fax: (0 76 53) 6 81 - 1 00 E-Mail: info@testo.de Internet: http://www.testo.com 0977 1042 en 01a

FCC statements: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the user’s authority to operate the equipment. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Power is so low that no RF exposure calculation is needed.


Document Created: 2015-07-15 09:36:30
Document Modified: 2015-07-15 09:36:30
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC