Module Approval Letter

FCC ID: 2ACSV-HF-LPT230

Cover Letter(s)

Download: PDF
FCCID_3552332

Company: High-Flying Electronics Technology Co., Ltd.
Add: Room 1002, Building 1, No.3000, Longdong Avenue,Pudong New Area, Shanghai,
China
Tel: 400-189-3108
Fax: 021-31291158-8089

Applicant               High-Flying Electronics Technology Co., Ltd.
FCC ID:                 2ACSV-HF-LPT230
                              Section 15.212 Modular Transmitters
Request        for      Modular            Request for Limited Modular Approval              

Approval
                     Requirements                  EUT Conditions                   Comply(Y/N)
                            Single Modular Approval Requirements
1          The radio elements of the modular         Refer to external photos.         Y
           transmitter must have their own           This module does have shield
           shielding. The physical crystal and       cover.
           tuning capacitors may be located
           external to the shielded radio
           elements.
2          The modular transmitter must have         All inputs to the modules are     Y
           buffered modulation/data inputs (if       buffered through logic or
           such inputs are provided) to ensure       microprocessor inputs.
           that the module will comply with part     Refer to Schematics.
           15.247      requirements       under
           conditions of excessive data rates or
           over‐modulation.
3          The modular transmitter must The module rated power is Y
           have its own power supply 3.3V.Refer to User Manual.
           regulation.
4          The modular transmitter must The modular transmitter has a Y
           comply with the antenna and               PCB antenna arrangement for Wi-
                                                     Fi, Refer to internal photo.
           transmission system requirements of
           §§15.203, 15.204(b) and 15.204(c).
           The antenna must either be
           permanently attached or employ a
           “unique” antenna coupler (at all
           connections between the module
           and the antenna, including the
           cable). The “professional installation”
           provision of §15.203 is not applicable
           to modules but can apply to limited
           modular approvals under paragraph
           (b) of this section.


5   The modular transmitter must          The modular transmitter is     Y
    be tested in a stand‐alone            connected to the controlled
    configuration, i.e., the module       board when testing.
    must not be inside another            Please refer to setup photo.
    device during testing for
    compliance with part 15.247
    requirements.       Unless     the
    transmitter module will be
    battery powered, it must comply
    with the AC line conducted
    requirements found in §15.207.
    AC or DC power lines and data
    input/output lines connected to
    the module must not contain
    ferrites, unless they will be
    marketed with the module (see
    §15.27(a)). The length of these
    lines shall be the length typical
    of actual use or, if that length is
    unknown,       at      least    10
    centimeters to insure that there
    is no coupling between the case
    of the module and supporting
    equipment. Any accessories,
    peripherals,      or       support
    equipment connected to the
    module during testing shall be
    unmodified and commercially
    available (see §15.31(i)).

6   If using a permanently affixed Refer to the label                    Y
    label, the modular transmitter
    must be labeled with its own
    FCC identification number, and,
    if the FCC identification number
    is not visible when the module is
    installed inside another device,
    then the outside of the device
    into which the module is
    installed must also display a
    label referring to the enclosed
    module. This exterior label can
    use wording such as the
    following: “Contains Transmitter


         Module FCC ID:2ACSV-HF-LPT230
         y
         Any   similar wording that
         expresses the same meaning
         may be used. The Grantee may
         either provide such a label,
         an example of which must
         be included in the application
         for equipment authorization, or,
         must provide adequate
         instructions along with the
         module which explain this
         requirement. In the latter case, a
         copy of these instructions must
         be included in the application for
         equipment authorization.

7         The modular transmitter must        Refer to manual              Y
          comply with any specific rules or
          operating requirements that
          ordinarily apply to a complete
          transmitter         and      the
          manufacturer must provide
          adequate instructions along with
          the module to explain any such
          requirements. A copy of these
          instructions must be included in
          the application for equipment
          authorization.
8         The modular transmitter must        The EUT will comply with     Y
          comply with any applicable RF       any applicable RF exposure
          exposure requirements in its        requirements in its final
          final configuration.                configuration.
Sincerely Yours,


Signature:
Title: General Manager



Document Created: 2019-09-20 04:28:42
Document Modified: 2019-09-20 04:28:42

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC