Test Report

FCC ID: 2ACSTAPSENSOR01

Test Report

Download: PDF
FCCID_4216567

TEST REPORT FCC ID: 2ACSTAPSENSOR01 Product: TRAINING BAG SENSOR Model No.: APSENSOR01 Additional Model No.: N/A Trade Mark: N/A Report No.: TCT190305E019 Issued Date: Mar. 19, 2019 Issued for: NCI TECHNOLOGY, INC. R108 Jiu Zhu Rd, Jiang Ning Eco.&Tech.Development Zone, Nanjing, Jiang Su Province, 211102 China Issued By: Shenzhen Tongce Testing Lab. 1B/F., Building 1, Yibaolai Industrial Park, Qiaotou, Fuyong, Baoan District, Shenzhen, Guangdong, China TEL: +86-755-27673339 FAX: +86-755-27673332 Note: This report shall not be reproduced except in full, without the written approval of Shenzhen Tongce Testing Lab. This document may be altered or revised by Shenzhen Tongce Testing Lab. personnel only, and shall be noted in the revision section of the document. The test results in the report only apply to the tested sample. Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 TABLE OF CONTENTS 1. Test Certification ..................................................................................... 3 2. Test Result Summary .............................................................................. 4 3. EUT Description ....................................................................................... 5 4. General Information................................................................................. 6 4.1. Test environment and mode ................................................................................. 6 4.2. Description of Support Units ................................................................................ 6 5. Facilities and Accreditations .................................................................. 7 5.1. Facilities ................................................................................................................. 7 5.2. Location ................................................................................................................. 7 5.3. Measurement Uncertainty ..................................................................................... 7 6. Test Results and Measurement Data ..................................................... 8 6.1. Antenna requirement ............................................................................................ 8 6.2. Conducted Emission ............................................................................................. 9 6.3. Conducted Output Power ................................................................................... 10 6.4. Emission Bandwidth ........................................................................................... 13 6.5. Power Spectral Density ....................................................................................... 16 6.6. Test Specification ................................................................................................ 16 6.7. Conducted Band Edge and Spurious Emission Measurement ....................... 19 6.8. Radiated Spurious Emission Measurement ...................................................... 22 Appendix A: Photographs of Test Setup Appendix B: Photographs of EUT Page 2 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 1. Test Certification Product: TRAINING BAG SENSOR Model No.: APSENSOR01 Additional N/A Model No.: Trade Mark: N/A Applicant: NCI TECHNOLOGY, INC. R108 Jiu Zhu Rd, Jiang Ning Eco.&Tech.Development Zone, Nanjing, Address: Jiang Su Province, 211102 China Manufacturer: NCI TECHNOLOGY, INC. R108 Jiu Zhu Rd, Jiang Ning Eco.&Tech.Development Zone, Nanjing, Address: Jiang Su Province, 211102 China Date of Test: Mar. 06, 2019 – Mar. 18, 2019 Applicable FCC CFR Title 47 Part 15 Subpart C Section 15.247 Standards: KDB 558074 D01 15.247 Meas Guidance v05r01 The above equipment has been tested by Shenzhen Tongce Testing Lab. and found compliance with the requirements set forth in the technical standards mentioned above. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Tested By: Date: Mar. 18, 2019 Kevin Huang Reviewed By: Date: Mar. 19, 2019 Beryl Zhao Approved By: Date: Mar. 19, 2019 Tomsin Page 3 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 2. Test Result Summary Requirement CFR 47 Section Result Antenna requirement §15.203/§15.247 (c) PASS AC Power Line Conducted §15.207 PASS Emission Conducted Peak Output §15.247 (b)(3) PASS Power §2.1046 §15.247 (a)(2) 6dB Emission Bandwidth PASS §2.1049 Power Spectral Density §15.247 (e) PASS 1§5.247(d) Band Edge PASS §2.1051, §2.1057 §15.205/§15.209 Spurious Emission PASS §2.1053, §2.1057 Note: 1. PASS: Test item meets the requirement. 2. Fail: Test item does not meet the requirement. 3. N/A: Test case does not apply to the test object. 4. The test result judgment is decided by the limit of test standard. Page 4 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 3. EUT Description Product: TRAINING BAG SENSOR Model No.: APSENSOR01 Additional Model No.: N/A Trade Mark: N/A Hardware Version: V 1.4 Software Version: V 1.7 BT Version: V4.2 Operation Frequency: 2402MHz~2480MHz Channel Separation: 2MHz Number of Channel: 40 Modulation GFSK Technology: Antenna Type: Ceramic Antenna Antenna Gain: 0dBi Power Supply: DC 3V(2*AAA Batteries) Operation Frequency each of channel Channel Frequency Channel Frequency Channel Frequency Channel Frequency 0 2402MHz 10 2422MHz 20 2442MHz 30 2462MHz 1 2404MHz 11 2424MHz 21 2444MHz 31 2464MHz … … … … … … … … 8 2418MHz 18 2438MHz 28 2458MHz 38 2478MHz 9 2420MHz 19 2440MHz 29 2460MHz 39 2480MHz Remark: Channel 0, 19 & 39 have been tested. Page 5 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 4. General Information 4.1. Test environment and mode Operating Environment: Temperature: 25.0 C Humidity: 56 % RH Atmospheric Pressure: 1010 mbar Test Mode: Engineering mode: Keep the EUT in continuous transmitting by select channel and modulations(The value of duty cycle is 98.46%) with Fully-charged battery. The sample was placed (0.8m below 1GHz, 1.5m above 1GHz) above the ground plane of 3m chamber. Measurements in both horizontal and vertical polarities were performed. During the test, each emission was maximized by: having the EUT continuously working, investigated all operating modes, rotated about all 3 axis (X, Y & Z) and considered typical configuration to obtain worst position, manipulating interconnecting cables, rotating the turntable, varying antenna height from 1m to 4m in both horizontal and vertical polarizations. The emissions worst-case are shown in Test Results of the following pages. 4.2. Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Equipment Model No. Serial No. FCC ID Trade Name / / / / / Note: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. 3. For conducted measurements (Output Power, 6dB Emission Bandwidth, Power Spectral Density, Spurious Emissions), the antenna of EUT is connected to the test equipment via temporary antenna connector, the antenna connector is soldered on the antenna port of EUT, and the temporary antenna connector is listed in the Test Instruments. Page 6 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 5. Facilities and Accreditations 5.1. Facilities The test facility is recognized, certified, or accredited by the following organizations: ● FCC - Registration No.: 645098 Shenzhen Tongce Testing Lab The 3m Semi-anechoic chamber has been registered and fully described in a report with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. ● IC - Registration No.: 10668A-1 The 3m Semi-anechoic chamber of Shenzhen TCT Testing Technology Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing 5.2. Location Shenzhen Tongce Testing Lab Address: 1B/F., Building 1, Yibaolai Industrial Park, Qiaotou, Fuyong, Baoan District, Shenzhen, Guangdong, China TEL: +86-755-27673339 5.3. Measurement Uncertainty The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item MU 1 Conducted Emission ±2.56dB 2 RF power, conducted ±0.12dB 3 Spurious emissions, conducted ±0.11dB 4 All emissions, radiated(<1G) ±3.92dB 5 All emissions, radiated(>1G) ±4.28dB 6 Temperature ±0.1°C 7 Humidity ±1.0% Page 7 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 6. Test Results and Measurement Data 6.1. Antenna requirement Standard requirement: FCC Part15 C Section 15.203 /247(c) 15.203 requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. 15.247(c) (1)(i) requirement: (i) Systems operating in the 2400-2483.5 MHz band that is used exclusively for fixed. Point-to-point operations may employ transmitting antennas with directional gain greater than 6dBi provided the maximum conducted output power of the intentional radiator is reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6dBi. E.U.T Antenna: The Bluetooth antenna is ceramic antenna which permanently attached, and the best case gain of the antenna is 0dBi. Antenna Page 8 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 6.2. Conducted Emission 6.2.1. Test Specification Test Requirement: FCC Part15 C Section 15.207 Test Method: ANSI C63.10:2013 Frequency Range: 150 kHz to 30 MHz Receiver setup: RBW=9 kHz, VBW=30 kHz, Sweep time=auto Frequency range Limit (dBuV) (MHz) Quasi-peak Average Limits: 0.15-0.5 66 to 56* 56 to 46* 0.5-5 56 46 5-30 60 50 Test Setup: Test Mode: Charging + Transmitting Mode 1. The E.U.T is connected to an adapter through a line impedance stabilization network (L.I.S.N.). This provides a 50ohm/50uH coupling impedance for the measuring equipment. 2. The peripheral devices are also connected to the main power through a LISN that provides a 50ohm/50uH coupling impedance with 50ohm termination. (Please Test Procedure: refer to the block diagram of the test setup and photographs). 3. Both sides of A.C. line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ANSI C63.10: 2013 on conducted measurement. N/A; Because the EUT is powered by the battery, so the Test Result: item is not applicable. Page 9 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

I c I Reporti: rorisessmon 6.3. Conducted Output Power 6.3.1. Test Specification Test Requirement: FCC Part15 C Section 15.247 (b)@) Test Method: KDBsssort Limit: 304Bm Spectrum Anarzer Test Mode: Refer to tem 4.1 1. The lesing falows fne Neasurement Procedure of FCC KDB No. 558074 D01 15.247 Meas Guidance v0501. 2. Set spectrum analyzer as following a) Set the RBW > DTS bandwidhh. ) Set VBW > 3 x RBW. Test Procedure: ) Set span > 3x RBW d) Sweep time = auto couple. 0) Detector = poak. 0 ) Alow trace to fully stablize. ) Use peak marker function to determine the peak ampliude lovel. Test Result PASS 6.3.2. Test Instruments Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer ras Fsu 200054 Sep. 20, 2019 RF cabe (okbe—26.5GH2) Tot REos NA Sep. 20, 2019 Antenna Connector Tot Rroor NA Sep. 20, 2019 Note: Trecaloraton iteral olhe abovetes rstuments is 12 mrdhs ard e caloratons e racesbleto intrnatonal system unt 30 Pase 10 o8« Halline: a00—66rte1s0 Tob bo—rer—27070000 Fas 270002 Mioiiwwndetlib.com

Report No.: TCT190305E019 6.3.3. Test Data BT LE mode Maximum Conducted Test channel Limit (dBm) Result Output Power (dBm) Lowest 3.91 30.00 PASS Middle 3.80 30.00 PASS Highest 3.74 30.00 PASS Test plots as follows: Page 11 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 BT LE mode Lowest channel * RBW 3 MHz Marker 1 [T1 ] * VBW 10 MHz 3.91 dBm Ref 20 dBm * Att 20 dB SWT 2.5 ms 2.401894231 GHz 20 Offset 0.5 dB A 10 1 1 PK MAXH 0 LVL -10 -20 -30 3DB -40 -50 -60 -70 -80 Center 2.402 GHz 600 kHz/ Span 6 MHz Date: 18.MAR.2019 14:12:13 Middle channel * RBW 3 MHz Marker 1 [T1 ] * VBW 10 MHz 3.80 dBm Ref 20 dBm * Att 20 dB SWT 2.5 ms 2.439951923 GHz 20 Offset 0.5 dB A 10 1 1 PK MAXH 0 LVL -10 -20 -30 3DB -40 -50 -60 -70 -80 Center 2.44 GHz 600 kHz/ Span 6 MHz Date: 18.MAR.2019 14:12:39 Highest channel * RBW 3 MHz Marker 1 [T1 ] * VBW 10 MHz 3.74 dBm Ref 20 dBm * Att 20 dB SWT 2.5 ms 2.479913462 GHz 20 Offset 0.5 dB A 10 1 1 PK MAXH 0 LVL -10 -20 -30 3DB -40 -50 -60 -70 -80 Center 2.48 GHz 600 kHz/ Span 6 MHz Date: 18.MAR.2019 14:13:23 Page 12 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 6.4. Emission Bandwidth 6.4.1. Test Specification Test Requirement: FCC Part15 C Section 15.247 (a)(2) Test Method: KDB558074 Limit: >500kHz Test Setup: Test Mode: Refer to item 4.1 1. The testing follows FCC KDB Publication No. 558074 D01 15.247 Meas Guidance v05r01. 2. Set to the maximum power setting and enable the EUT transmit continuously. 3. Make the measurement with the spectrum analyzer's Test Procedure: resolution bandwidth (RBW) = 100 kHz. Set the Video bandwidth (VBW) = 300 kHz. In order to make an accurate measurement. The 6dB bandwidth must be greater than 500 kHz. 4. Measure and record the results in the test report. Test Result: PASS 6.4.2. Test Instruments RF Test Room Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer R&S FSU 200054 Sep. 20, 2019 RF cable TCT RE-06 N/A Sep. 20, 2019 (9kHz-26.5GHz) Antenna Connector TCT RFC-01 N/A Sep. 20, 2019 Note: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to international system unit (SI). Page 13 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 6.4.3. Test data 6dB Emission Bandwidth (kHz) Test channel BT LE mode Limit Result Lowest 602.56 >500k Middle 625.00 >500k PASS Highest 602.56 >500k Test plots as follows: Page 14 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 BT LE mode Lowest channel * RBW 30 kHz Delta 2 [T1 ] * VBW 100 kHz -0.10 dB Ref 20 dBm * Att 20 dB SWT 10 ms 602.564102582 kHz 20 Offset 0.5 dB Marker 1 [T1 ] -4.78 dBm 2.401673077 GHz A 10 1 PK MAXH D1 1.22 dBm 0 1 2 LVL D2 -4.78 dBm -10 -20 -30 3DB -40 -50 -60 -70 -80 Center 2.402 GHz 200 kHz/ Span 2 MHz Date: 18.MAR.2019 14:08:37 Middle channel * RBW 30 kHz Delta 2 [T1 ] * VBW 100 kHz -0.08 dB Ref 20 dBm * Att 20 dB SWT 10 ms 625.000000013 kHz 20 Offset 0.5 dB Marker 1 [T1 ] -6.03 dBm 2.439666667 GHz A 10 1 PK MAXH 0 D1 0 dBm LVL 1 2 D2 -6 dBm -10 -20 -30 3DB -40 -50 -60 -70 -80 Center 2.44 GHz 200 kHz/ Span 2 MHz Date: 18.MAR.2019 14:10:06 Highest channel * RBW 30 kHz Delta 2 [T1 ] * VBW 100 kHz -0.31 dB Ref 20 dBm * Att 20 dB SWT 10 ms 602.564102579 kHz 20 Offset 0.5 dB Marker 1 [T1 ] -4.79 dBm 2.479673077 GHz A 10 1 PK MAXH D1 1.01 dBm 0 1 2 LVL D2 -4.99 dBm -10 -20 -30 3DB -40 -50 -60 -70 -80 Center 2.48 GHz 200 kHz/ Span 2 MHz Date: 18.MAR.2019 14:11:19 Page 15 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 6.5. Power Spectral Density 6.6. Test Specification Test Requirement: FCC Part15 C Section 15.247 (e) Test Method: KDB558074 The peak power spectral density shall not be greater Limit: than 8dBm in any 3kHz band at any time interval of continuous transmission. Test Setup: Test Mode: Refer to item 4.1 1. The testing follows Measurement Procedure 10.2 Method PKPSD of FCC KDB Publication No. 558074 D01 15.247 Meas Guidance v05r01. 2. The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator. The path loss was compensated to the results for each measurement. 3. Set to the maximum power setting and enable the EUT transmit continuously. Test Procedure: 4. Make the measurement with the spectrum analyzer's resolution bandwidth (RBW): 3 kHz ≤ RBW ≤ 100 kHz. Video bandwidth VBW ≥ 3 x RBW. In order to make an accurate measurement, set the span to 1.5 times DTS Channel Bandwidth. (6dB BW) 5. Detector = peak, Sweep time = auto couple, Trace mode = max hold, Allow trace to fully stabilize. Use the peak marker function to determine the maximum power level. 6. Measure and record the results in the test report. Test Result: PASS 6.6.1. Test Instruments RF Test Room Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer R&S FSU 200054 Sep. 20, 2019 RF cable TCT RE-06 N/A Sep. 20, 2019 (9kHz-26.5GHz) Antenna Connector TCT RFC-01 N/A Sep. 20, 2019 Note: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to international system unit (SI). Page 16 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 6.6.2. Test data Power Spectral Density (dBm/3kHz) Test channel BT LE mode Limit Result Lowest -14.30 8 dBm/3kHz Middle -14.36 8 dBm/3kHz PASS Highest -14.46 8 dBm/3kHz Test plots as follows: Page 17 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 BT LE mode Lowest channel * RBW 3 kHz Marker 1 [T1 ] * VBW 10 kHz -14.30 dBm Ref 20 dBm * Att 20 dB SWT 170 ms 2.402016827 GHz 20 Offset 0.5 dB A 10 1 PK MAXH 0 LVL -10 1 -20 -30 3DB -40 -50 -60 -70 -80 Center 2.402 GHz 150 kHz/ Span 1.5 MHz Date: 18.MAR.2019 14:16:26 Middle channel * RBW 3 kHz Marker 1 [T1 ] * VBW 10 kHz -14.36 dBm Ref 20 dBm * Att 20 dB SWT 170 ms 2.440016827 GHz 20 Offset 0.5 dB A 10 1 PK MAXH 0 LVL -10 1 -20 -30 3DB -40 -50 -60 -70 -80 Center 2.44 GHz 150 kHz/ Span 1.5 MHz Date: 18.MAR.2019 14:17:03 Highest channel * RBW 3 kHz Marker 1 [T1 ] * VBW 10 kHz -14.46 dBm Ref 20 dBm * Att 20 dB SWT 170 ms 2.480016827 GHz 20 Offset 0.5 dB A 10 1 PK MAXH 0 LVL -10 1 -20 -30 3DB -40 -50 -60 -70 -80 Center 2.48 GHz 150 kHz/ Span 1.5 MHz Date: 18.MAR.2019 14:17:38 Page 18 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 6.7. Conducted Band Edge and Spurious Emission Measurement 6.7.1. Test Specification Test Requirement: FCC Part15 C Section 15.247 (d) Test Method: KDB558074 In any 100 kHz bandwidth outside of the authorized frequency band, the emissions which fall in the non-restricted bands shall be attenuated at least 20 dB / 30dB relative to the maximum PSD level in 100 kHz by Limit: RF conducted measurement and radiated emissions which fall in the restricted bands, as defined in Section 15.205(a), must also comply with the radiated emission limits specified in Section 15.209(a). Test Setup: Test Mode: Refer to item 4.1 1. The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator. The path loss was compensated to the results for each measurement. 2. Set to the maximum power setting and enable the EUT transmit continuously. 3. Set RBW = 100 kHz, VBW=300 kHz, Peak Detector. Unwanted Emissions measured in any 100 kHz bandwidth outside of the authorized frequency band shall be attenuated by at least 20 dB relative to the Test Procedure: maximum in-band peak PSD level in 100 kHz when maximum peak conducted output power procedure is used. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, the attenuation required under this paragraph shall be 30 dB instead of 20 dB per 15.247(d). 4. Measure and record the results in the test report. 5. The RF fundamental frequency should be excluded against the limit line in the operating frequency band. Test Result: PASS Page 19 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 6.7.2. Test Instruments RF Test Room Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer R&S FSU 200054 Sep. 20, 2019 RF cable TCT RE-06 N/A Sep. 20, 2019 (9kHz-26.5GHz) Antenna Connector TCT RFC-01 N/A Sep. 20, 2019 Note: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to international system unit (SI). 6.7.3. Test Data 100kHz PSD reference Level Band Edge * RBW 100 kHz Marker 1 [T1 ] * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz 3.29 dBm * VBW 300 kHz -56.97 dBm Ref 20 dBm * Att 20 dB SWT 2.5 ms 2.402000000 GHz Ref 20 dBm * Att 20 dB SWT 10 ms 2.390000000 GHz 20 Offset 0.5 dB 20 Offset 0.5 dB Marker 2 [T1 ] -47.06 dBm A 2.400000000 GHz A 10 10 1 Marker 3 [T1 ] 1 PK 1 PK -41.77 dBm MAXH MAXH 0 0 2.334358974 GHz LVL LVL -10 -10 D1 -16.71 dBm D1 -16.71 dBm -20 -20 -30 -30 3DB 3DB 3 -40 -40 2 -50 -50 1 -60 -60 -70 -70 F2 F1 -80 -80 Center 2.402 GHz 150 kHz/ Span 1.5 MHz Start 2.31 GHz 9.5 MHz/ Stop 2.405 GHz Date: 18.MAR.2019 14:19:03 Date: 18.MAR.2019 14:22:56 Spurious emission * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz 3.18 dBm Ref 20 dBm * Att 20 dB SWT 2.5 s 2.402150000 GHz 20 Offset 0.5 dB Marker 2 [T1 ] -32.55 dBm 4.801767000 GHz A 10 1 Marker 3 [T1 ] 1 PK -51.68 dBm MAXH 0 7.206378000 GHz LVL -10 D1 -16.71 dBm -20 -30 2 3DB -40 3 -50 -60 -70 -80 Start 30 MHz 2.497 GHz/ Stop 25 GHz Date: 18.MAR.2019 14:28:46 Lowest Channel Page 20 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 100kHz PSD reference Level Spurious emission * RBW 100 kHz Marker 1 [T1 ] * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz 3.18 dBm * VBW 300 kHz 3.17 dBm Ref 20 dBm * Att 20 dB SWT 2.5 ms 2.440000000 GHz Ref 20 dBm * Att 20 dB SWT 2.5 s 2.439605000 GHz 20 Offset 0.5 dB 20 Offset 0.5 dB Marker 2 [T1 ] -36.30 dBm A 4.879174000 GHz A 10 10 1 1 Marker 3 [T1 ] 1 PK 1 PK -46.62 dBm MAXH MAXH 0 0 7.318743000 GHz LVL LVL -10 -10 D1 -16.82 dBm D1 -16.82 dBm -20 -20 -30 -30 2 3DB 3DB -40 -40 3 -50 -50 -60 -60 -70 -70 -80 -80 Center 2.44 GHz 150 kHz/ Span 1.5 MHz Start 30 MHz 2.497 GHz/ Stop 25 GHz Date: 18.MAR.2019 14:20:02 Date: 18.MAR.2019 14:27:25 Middle Channel 100kHz PSD reference Level Band Edge * RBW 100 kHz Marker 1 [T1 ] * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz 3.12 dBm * VBW 300 kHz -50.54 dBm Ref 20 dBm * Att 20 dB SWT 2.5 ms 2.479997596 GHz Ref 20 dBm * Att 20 dB SWT 10 ms 2.483500000 GHz 20 Offset 0.5 dB 20 Offset 0.5 dB Marker 2 [T1 ] -58.88 dBm A 2.500000000 GHz A 10 10 1 Marker 3 [T1 ] 1 PK 1 PK -50.54 dBm MAXH MAXH 0 0 2.483500000 GHz LVL LVL -10 -10 D1 -16.88 dBm D1 -16.88 dBm -20 -20 -30 -30 3DB 3DB -40 -40 1 3 -50 -50 2 -60 -60 -70 -70 F2 F1 -80 -80 Center 2.48 GHz 150 kHz/ Span 1.5 MHz Start 2.477 GHz 2.8 MHz/ Stop 2.505 GHz Date: 18.MAR.2019 14:21:01 Date: 18.MAR.2019 14:24:11 Spurious emission * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz 2.20 dBm Ref 20 dBm * Att 20 dB SWT 2.5 s 2.479557000 GHz 20 Offset 0.5 dB Marker 2 [T1 ] -39.20 dBm 4.959078000 GHz A 10 Marker 3 [T1 ] 1 1 PK -47.02 dBm MAXH 0 7.438599000 GHz LVL -10 D1 -16.88 dBm -20 -30 2 3DB -40 3 -50 -60 -70 -80 Start 30 MHz 2.497 GHz/ Stop 25 GHz Date: 18.MAR.2019 14:30:49 Highest Channel Page 21 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 6.8. Radiated Spurious Emission Measurement 6.8.1. Test Specification Test Requirement: FCC Part15 C Section 15.209 Test Method: ANSI C63.10: 2013 Frequency Range: 9 kHz to 25 GHz Measurement Distance: 3m Antenna Polarization: Horizontal & Vertical Operation mode: Refer to item 4.1 Frequency Detector RBW VBW Remark 9kHz- 150kHz Quasi-peak 200Hz 1kHz Quasi-peak Value 150kHz- Quasi-peak 9kHz 30kHz Quasi-peak Value Receiver Setup: 30MHz 30MHz-1GHz Quasi-peak 100KHz 300KHz Quasi-peak Value Peak 1MHz 3MHz Peak Value Above 1GHz Peak 1MHz 10Hz Average Value Field Strength Measurement Frequency (microvolts/meter) Distance (meters) 0.009-0.490 2400/F(KHz) 300 0.490-1.705 24000/F(KHz) 30 1.705-30 30 30 30-88 100 3 88-216 150 3 Limit: 216-960 200 3 Above 960 500 3 Measurement Field Strength Frequency Distance Detector (microvolts/meter) (meters) 500 3 Average Above 1GHz 5000 3 Peak For radiated emissions below 30MHz Test setup: 30MHz to 1GHz Page 22 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 Above 1GHz 1. For the radiated emission test below 1GHz: The EUT was placed on a turntable with 0.8 meter above ground. The EUT was set 3 meters from the interference receiving antenna, which was mounted on the top of a variable height antenna tower. The EUT was arranged to its worst case and then tune the antenna tower (from 1 m to 4 m) and turntable (from 0 degree to 360 degrees) to find the maximum reading. A pre-amp and a high PASS filter are used for the test in order to get better signal level. For the radiated emission test above 1GHz: Test Procedure: Place the measurement antenna on a turntable with 1.5 meter above ground, which is away from each area of the EUT determined to be a source of emissions at the specified measurement distance, while keeping the measurement antenna aimed at the source of emissions at each frequency of significant emissions, with polarization oriented for maximum response. The measurement antenna may have to be higher or lower than the EUT, depending on the radiation pattern of the emission and staying aimed at the emission source for receiving the maximum signal. The final Page 23 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com


Report No.: TCT190305E019 6.8.2. Test Instruments Radiated Emission Test Site (966) Name of Serial Manufacturer Model Calibration Due Equipment Number ROHDE&SCHW Test Receiver ESIB7 100197 Jul. 17, 2019 ARZ ROHDE&SCHW Spectrum Analyzer FSQ40 200061 Sep. 20, 2019 ARZ EM Electronics Pre-amplifier Corporation EM30265 07032613 Sep. 16, 2019 CO.,LTD Pre-amplifier HP 8447D 2727A05017 Sep. 16, 2019 Loop antenna ZHINAN ZN30900A 12024 Oct. 20, 2019 Broadband Antenna Schwarzbeck VULB9163 340 Sep. 02, 2019 Horn Antenna Schwarzbeck BBHA 9120D 631 Oct. 20, 2019 Horn Antenna A-INFO LB-180400-KF J211020657 Sep. 16, 2019 Antenna Mast Keleto RE-AM N/A N/A Coax cable TCT RE-low-01 N/A Sep. 16, 2019 (9KHz-1GHz) Coax cable TCT RE-high-02 N/A Sep. 16, 2019 (9KHz-40GHz) Coax cable TCT RE-low-03 N/A Sep. 16, 2019 (9KHz-1GHz) Coax cable TCT RE-high-04 N/A Sep. 16, 2019 (9KHz-40GHz) Shurple EMI Test Software EZ-EMC N/A N/A Technology Note: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to international system unit (SI). Page 25 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 6.8.3. Test Data Please refer to following diagram for individual Below 1GHz Horizontal: Page 26 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 Vertical: Note: 1.The low frequency, which started from 9KHz~30MHz, was pre-scanned and the result which was 20dB lower than the limit line per 15.31(o) was not reported 2. Measurements were conducted in all three channels (high, middle, low), and the worst case Mode (Lowest channel) was submitted only. Page 27 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 Above 1GHz Low channel: 2402 MHz Peak AV Correction Emission Level Frequency Ant. Pol. Peak limit AV limit Margin (MHz) H/V reading reading Factor Peak AV (dBµV/m) (dBµV/m) (dB) (dBµV) (dBuV) (dB/m) (dBµV/m) (dBµV/m) 2390 H 45.35 --- -8.27 37.08 --- 74 54 -16.92 4804 H 47.84 --- 0.66 48.50 --- 74 54 -5.50 7206 H 38.17 --- 9.50 47.67 --- 74 54 -6.33 --- H --- --- --- --- ---- --- --- --- 2390 V 43.03 --- -8.27 34.76 --- 74 54 -19.24 4804 V 44.61 --- 0.66 45.27 --- 74 54 -8.73 7206 V 38.27 --- 9.50 47.77 --- 74 54 -6.23 --- V --- --- --- --- --- --- --- --- Middle channel: 2440MHz Frequency Ant. Pol. Peak AV Correction Emission Level Peak limit AV limit Margin reading reading Factor Peak AV (MHz) H/V (dBµV) (dBµV) (dB/m) (dBµV/m) (dBµV/m) (dBµV/m) (dBµV/m) (dB) 4880 H 43.52 --- 0.99 44.51 --- 74 54 -9.49 7320 H 38.19 --- 9.87 48.06 --- 74 54 -5.94 --- H --- --- --- --- ---- --- --- --- 4880 V 44.37 --- 0.99 45.36 --- 74 54 -8.64 7320 V 37.81 --- 9.87 47.68 --- 74 54 -6.32 --- V --- --- --- --- ---- --- --- --- High channel: 2480 MHz Peak AV Correction Emission Level Frequency Ant. Pol. Peak limit AV limit Margin (MHz) H/V reading reading Factor Peak AV (dBµV/m) (dBµV/m) (dB) (dBµV) (dBµV) (dB/m) (dBµV/m) (dBµV/m) 2483.5 H 46.25 --- -7.83 38.42 --- 74 54 -15.58 4960 H 48.07 --- 1.33 49.40 --- 74 54 -4.60 7440 H 39.56 --- 10.22 49.78 --- 74 54 -4.22 --- H --- --- --- --- ---- --- --- --- 2483.5 V 48.78 --- -7.83 40.95 --- 74 54 -13.05 4960 V 47.64 --- 1.33 48.97 --- 74 54 -5.03 7440 V 37.96 --- 10.22 48.18 --- 74 54 -5.82 --- V --- --- --- --- --- --- --- --- Note: 1. Emission Level=Peak Reading + Correction Factor; Correction Factor= Antenna Factor + Cable loss – Pre-amplifier 2. Margin (dB) = Emission Level (Peak) (dBµV/m)-Average limit (dBµV/m) 3. The emission levels of other frequencies are very lower than the limit and not show in test report. 4. Measurements were conducted from 1 GHz to the 10th harmonic of highest fundamental frequency. 5. Data of measurement shown “---“in the above table mean that the reading of emissions is attenuated more than 20 dB below the limits or the field strength is too small to be measured. Page 28 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 Appendix A: Photographs of Test Setup Product: TRAINING BAG SENSOR Model: APSENSOR01 Radiated Emission Page 29 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 Appendix B: Photographs of EUT Product: TRAINING BAG SENSOR Model: APSENSOR01 External Photos Page 30 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 Page 31 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 Product: TRAINING BAG SENSOR Model: APSENSOR01 Internal Photos Page 32 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 Page 33 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com

Report No.: TCT190305E019 *****END OF REPORT***** Page 34 of 34 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com


Document Created: 2019-03-22 18:20:44
Document Modified: 2019-03-22 18:20:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC