Test report

FCC ID: 2ACLV59246

Test Report

Download: PDF
FCCID_2859457

FCC 47 CFR PART 15 SUBPART C CERTIFICATION TEST REPORT OF DESIRE REMOTE CONTROL LOVE EGG Model No.: LH-59246 Trademark: N/A FCC ID: 2ACLV59246 Report No.: ED151019050E Issue Date: November 17, 2015 Prepared for ShenZhen Hunicom Electronics Co., Ltd Room 227, Block A, Zhihui Innovation Center, Qianjin 2nd Road, Baoan District, Shenzhen, China Prepared by EMTEK(Dongguan) Co., Ltd. No.281, Guantai Road, Nancheng District, Dongguan, Guangdong, China TEL: 86-769-22807078 FAX: 86-769-22807079 This report shall not be reproduced, except in full, without the written approval of EMTEK(Dongguan) Co., Ltd. TRF No.: FCC 15.231/A Page 1 of 27 Report No.: ED151019050E Ver. 1.0

TEST RESULT CERTIFICATION ShenZhen Hunicom Electronics Co., Ltd Applicant: Room 227, Block A, Zhihui Innovation Center, Qianjin 2nd Road, Baoan District, Shenzhen, China ShenZhen Hunicom Electronics Co., Ltd Manufacturer: Room 227, Block A, Zhihui Innovation Center, Qianjin 2nd Road, Baoan District, Shenzhen, China Product Description: DESIRE REMOTE CONTROL LOVE EGG Model Number: LH-59246 Serial Number: N/A Measurement Procedure Used: APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 2, Subpart J PASS FCC 47 CFR Part 15, Subpart C We hereby certify that: The above equipment was tested by EMTEK(Dongguan) Co., Ltd. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10-2013 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 2 and Part 15.231 REQUIREMENTS. The test results of this report relate only to the tested sample identified in this report. Date of Test : October 19, 2015 to November 17, 2015 Prepared by : Ivy Huang/Editor Reviewer : Alan He/Supervisor Approve & Authorized Signer : Sam Lv/Manager TRF No.: FCC 15.231/A Page 2 of 27 Report No.: ED151019050E Ver. 1.0

Modified Information Version Summary Revision Date Report No. Ver.1.0 Original Report / ED151019050E TRF No.: FCC 15.231/A Page 3 of 27 Report No.: ED151019050E Ver. 1.0

Table of Contents 1 EUT TECHNICAL DESCRIPTION ............................................................................. 5 2 SUMMARY OF TEST RESULT ................................................................................. 6 3 TEST METHODOLOGY ............................................................................................. 7 3.1 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................................... 7 3.2 MEASUREMENT EQUIPMENT USED ..................................................................................... 7 3.3 DESCRIPTION OF TEST MODES ............................................................................................ 7 4 FACILITIES AND ACCREDITATIONS ...................................................................... 7 4.1 FACILITIES ................................................................................................................................ 7 4.2 LABORATORY ACCREDITATIONS AND LISTINGS ............................................................... 8 5 TEST SYSTEM UNCERTAINTY ................................................................................ 9 6 SETUP OF EQUIPMENT UNDER TEST ................................................................. 10 6.1 RADIO FREQUENCY TEST SETUP 1 .................................................................................... 10 6.2 RADIO FREQUENCY TEST SETUP 2 .................................................................................... 10 6.3 CONDUCTED EMISSION TEST SETUP ................................................................................ 11 6.4 BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM.................................................... 12 6.5 SUPPORT EQUIPMENT ......................................................................................................... 12 7 TEST REQUIREMENTS .......................................................................................... 13 7.1 OCCUPIED BANDWIDTH ....................................................................................................... 13 7.2 RADIATED SPURIOUS EMISSION ........................................................................................ 15 7.3 TRANSMISSION REQUIREMENT .......................................................................................... 20 7.4 ANTENNA APPLICATION .............................................................................................................. 22 TRF No.: FCC 15.231/A Page 4 of 27 Report No.: ED151019050E Ver. 1.0

1 EUT TECHNICAL DESCRIPTION Characteristics Description Device Type: DESIRE REMOTE CONTROL LOVE EGG Modulation: ASK Operating Frequency 433.92MHz Range(s): Number of Channels: 1 channel Antenna Type : Internal PCB antenna Antenna Gain: 2.14dBi Power supply: DC 3V Note: for more details, please refer to the User’s manual of the EUT. The EUT has been associated with peripherals pursuant to ANSI C63.10-2013 and configuration operated in a manner tended to maximize its emission characteristics in a typical application. Frequency range investigated: radiation (9 KHz to the 10th harmonic of the highest fundamental frequency or to 40 GHz, whichever is lower). For Radiated: The EUT’s antenna was pre-tested under the following modes: Test Mode Description Mode A X-Y axis Mode B Y-Z axis Mode C X-Z axis From the above modes, the worst case was found in Mode A. All the x/y/z orientation has been investigated, and only worst case is presented in this report. TRF No.: FCC 15.231/A Page 5 of 27 Report No.: ED151019050E Ver. 1.0

2 SUMMARY OF TEST RESULT FCC Part Clause Test Parameter Verdict Remark 15.231(c) Occupied Bandwidth PASS 15.231(b) Radiated Spurious Emissions PASS 15.231(b) Transmission Requirement PASS 15.203 Antenna Requirement PASS 15.207(a) Conducted Emission N/A DC3V NOTE1: N/A (Not Applicable) RELATED SUBMITTAL(S) / GRANT(S): This submittal(s) (test report) is intended for FCC ID: 2ACLV59246 filing to comply with Section 15.231 of the FCC Part 15, Subpart C Rules TRF No.: FCC 15.231/A Page 6 of 27 Report No.: ED151019050E Ver. 1.0

3 TEST METHODOLOGY 3.1 GENERAL DESCRIPTION OF APPLIED STANDARDS According to its specifications, the EUT must comply with the requirements of the following standards: FCC 47 CFR Part 2, Subpart J FCC 47 CFR Part 15, Subpart C 3.2 MEASUREMENT EQUIPMENT USED 1.1.1. Radiated Emission Test Equipment EQUIPMENT MFR MODEL SERIAL LAST CAL. TYPE NUMBER NUMBER EMI Test Receiver Rohde & Schwarz ESU 1302.6005.26 05/17/2015 Pre-Amplifier HP 8447D 2944A07999 05/17/2015 Bilog Antenna Schwarzbeck VULB9163 142 05/17/2015 Loop Antenna ARA PLA-1030/B 1029 05/17/2015 Horn Antenna Schwarzbeck BBHA 9170 BBHA9170399 05/17/2015 Horn Antenna Schwarzbeck BBHA 9120 D143 05/17/2015 Cable Schwarzbeck AK9513 ACRX1 05/17/2015 Cable Rosenberger N/A FP2RX2 05/17/2015 Cable Schwarzbeck AK9513 CRPX1 05/17/2015 Cable Schwarzbeck AK9513 CRRX2 05/17/2015 1.1.2. Radio Frequency Test Equipment EQUIPMENT MFR MODEL SERIAL LAST TYPE NUMBER NUMBER CAL. Spectrum Analyzer Agilent E4407B 88156318 05/17/2015 Power meter Anritsu ML2495A 0824006 05/17/2015 Power sensor Anritsu MA2411B 0738172 05/17/2015 Remark: Each piece of equipment is scheduled for calibration once a year. 3.3 DESCRIPTION OF TEST MODES The EUT has been tested under its typical operating condition. The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner which intends to maximize its emission characteristics in a continuous normal application. The Transmitter was operated in the normal operating mode. The TX frequency was fixed which was for the purpose of the measurements. Pre-defined engineering program for regulatory testing used to control the EUT for staying in continuous transmitting and receiving mode is programmed. 4 FACILITIES AND ACCREDITATIONS 4.1 FACILITIES All measurement facilities used to collect the measurement data are located at No.281, Guantai Road, Nancheng District,Dongguan, Guangdong, China The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.10 and CISPR Publication 22. TRF No.: FCC 15.231/A Page 7 of 27 Report No.: ED151019050E Ver. 1.0

4.2 LABORATORY ACCREDITATIONS AND LISTINGS Site Description EMC Lab. : Registered on FCC, June 18, 2014 The Certificate Number is 247565. Registered on Industry Canada, February 19, 2014 The Certificate Number is 9444A Name of Firm : EMTEK(Dongguan) Co., Ltd. Site Location : No.281, Guantai Road, Nancheng District, Dongguan, Guangdong, China TRF No.: FCC 15.231/A Page 8 of 27 Report No.: ED151019050E Ver. 1.0

5 TEST SYSTEM UNCERTAINTY The following measurement uncertainty levels have been estimated for tests performed on the apparatus: Parameter Uncertainty Radio Frequency ±1x10^-5 Conducted Emissions Test ±2.0dB Radiated Emission Test ±2.0dB Occupied Bandwidth Test ±1.0dB All emission, radiated ±3dB Temperature ±0.5℃ Humidity ±3% Measurement Uncertainty for a level of Confidence of 95% TRF No.: FCC 15.231/A Page 9 of 27 Report No.: ED151019050E Ver. 1.0

6 SETUP OF EQUIPMENT UNDER TEST 6.1 RADIO FREQUENCY TEST SETUP 1 The component’s antenna ports(s) of the EUT are connected to the measurement instrument per an appropriate attenuator. The EUT is controlled by PC/software to emit the specified signals for the purpose of measurements. EUT Attenuator Measurement Instrument 6.2 RADIO FREQUENCY TEST SETUP 2 The test site semi-anechoic chamber has met the requirement of NSA tolerance 4 dB according to the standards: ANSI C63.10. The test distance is 3m.The setup is according to the requirements in Section 13.1.4.1 of ANSI C63.10-2013 and CAN/CSA-CEI/IEC CISPR 22. The maximal emission value is acquired by adjusting the antenna height, polarisation and turntable azimuth. Normally, the height range of antenna is 1 m to 4 m, the azimuth range of turntable is 0° to 360°, and the receive antenna has two polarizations Vertical (V) and Horizontal (H). Below 30MHz： The EUT is placed on a turntable 0.8 meters above the ground in the chamber, 3 meter away from the antenna (loop antenna). The Antenna should be positioned with its plane vertical at the specified distance from the EUT and rotated about its vertical axis for maximum response at each azimuth about the EUT. The center of the loop shall be 1 m above the ground. For certain applications, the loop antenna plane may also need to be positioned horizontally at the specified distance from the EUT. Above 30MHz： The EUT is placed on a turntable 0.8 meters above the ground in the chamber, 3 meter away from the antenna. The maximal emission value is acquired by adjusting the antenna height, polarisation and turntable azimuth. Normally, the height range of antenna is 1 m to 4 m, the azimuth range of turntable is 0° to 360°, and the receive antenna has two polarizations Vertical (V) and Horizontal (H). (a) Radiated Emission Test Set-Up, Frequency Below 30MHz Turntable 3m EUT Test 0.8 m Receiver Ground Plane Coaxial Cable (b) Radiated Emission Test Set-Up, Frequency Below 1000MHz 3m Turntable 1m to 4m EUT Test 0.8m Receiver Ground Plane Coaxial Cable TRF No.: FCC 15.231/A Page 10 of 27 Report No.: ED151019050E Ver. 1.0

(C) Radiated Emission Test Set-Up, Frequency above 1000MHz 3m Turntable 4m EUT Test 1.5m 1m Amplifier Receiver 6.3 CONDUCTED EMISSION TEST SETUP The mains cable of the EUT (maybe per AC/DC Adapter) must be connected to LISN. The LISN shall be placed 0.8 m from the boundary of EUT and bonded to a ground reference plane for LISN mounted on top of the ground reference plane. This distance is between the closest points of the LISN and the EUT. All other units of the EUT and associated equipment shall be at least 0.8m from the LISN. Ground connections, where required for safety purposes, shall be connected to the reference ground point of the LISN and, where not otherwise provided or specified by the manufacturer, shall be of same length as the mains cable and run parallel to the mains connection at a separation distance of not more than 0.1 m. According to the requirements in ANSI C63.10-2013 Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30 MHz using CISPR Quasi-Peak and average detector mode. Reference Ground EUT Auxiliary Reference Equipment Ground EMI Receiver 50Ω 80cm 80cm LISN LISN TRF No.: FCC 15.231/A Page 11 of 27 Report No.: ED151019050E Ver. 1.0

6.4 BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM EUT AC Adapter AC Source 6.5 SUPPORT EQUIPMENT Item Equipment Mfr/Brand Model/Type No. Series No. Note 1. Notebook ASUS P45V N/A Notes: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. TRF No.: FCC 15.231/A Page 12 of 27 Report No.: ED151019050E Ver. 1.0

7 TEST REQUIREMENTS 7.1 OCCUPIED BANDWIDTH 7.1.1 Applicable Standard According to FCC Part 2.1049 and part 15.231(c) 7.1.2 Conformance Limit The bandwidth of the emission shall be no wider than 0.25% of the center frequency for devices operating above 70 MHz and below 900 MHz. For devices operating above 900 MHz, the emission shall be no wider than 0.5% of the center frequency. Bandwidth is determined at the points 20 dB down from the modulated carrier. 7.1.3 Test Configuration Test according to clause 6.1 radio frequency test setup 1 7.1.4 Test Procedure The EUT was operating in transmit mode and controlled its channel. Printed out the test result from the spectrum by hard copy function. The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator. The path loss was compensated to the results for each measurement. Set to the maximum power setting and enable the EUT transmit continuously Set RBW = 1% occupied bandwidth (1MHz). Set the video bandwidth (VBW) =3MHz. Set Span= approximately 2 to 3 times the occupied bandwidth Set Detector = Peak. Set Trace mode = max hold. Set Sweep = auto couple. The EUT should be transmitting at its maximum data rate. Allow the trace to stabilize. Use the marker-to-peak function to set the marker to the peak of the emission. Use the marker-delta function to measure 99% down one side of the emission. Reset the markerdelta function, and move the marker to the other side of the emission, until it is (as close as possible to) even with the reference marker level. The marker-delta reading at this point is the 99% bandwidth of the emission. If this value varies with different modes of operation (e.g., data rate, modulation format, etc.), repeat this test for each variation. Measure and record the results in the test report. Test Results Temperature : 28℃ Test Date : November 10, 2015 Humidity : 65 % Test By: Andy Modulation Channel Channel Frequency Measurement Limit Mode Number (MHz) Bandwidth (kHz) Verdict (kHz) ASK 0 433.92 1461 ≤1084.8KHz PASS Note: N/A (Not Applicable) BW=0.25% of the center frequency TRF No.: FCC 15.231/A Page 13 of 27 Report No.: ED151019050E Ver. 1.0

Occupied Bandwidth Test Model Channel 0: 433.92MHz ASK Modulation TRF No.: FCC 15.231/A Page 14 of 27 Report No.: ED151019050E Ver. 1.0

7.2 RADIATED SPURIOUS EMISSION 7.2.1 Applicable Standard According to FCC Part 15.231(b) and 15.209 7.2.2 Conformance Limit Intentional radiators may operate at a periodic rate exceeding that specified in paragraph (a) of this section and may be employed for any type of operation, including operation prohibited in paragraph (a) of this section, provided the intentional radiator complies with the provisions of paragraphs (b) through (d) of this section, except the field strength table in paragraph (b) of this section is replaced by the following: FCC 15.205 Restricted frequency band FCC 15.209 Limited Frequencies Field Strength Measurement Distance (MHz) (micorvolts/meter) (meters) 0.009~0.490 2400/F(KHz) 300 0.490~1.705 24000/F(KHz) 30 1.705~30.0 30 30 30~88 100 3 88~216 150 3 216~960 200 3 960~1000 500 3 Above 1GHz 74 dBuV/m (PEAK) 54 dBuV/m (AVERAGE) TRF No.: FCC 15.231/A Page 15 of 27 Report No.: ED151019050E Ver. 1.0

15.231 Limited The field intensity in micro-volts per meter can then be determined by the following equation: FI(V/ m) = 10FI (dBV/ m) / 20 The FCC specified emission limits were calculated according the EUT operating frequency and obtained by following linear interpolation equations: (a) For fundamental frequency: fEUT : EUT Operating Frequency Emission Limit (V/m) 12500(V/m) – 3750(V/m) = [fEUT(MHz) – 260(MHz)] X + 3750(V/m) 470(MHz) – 260(MHz) (b) For spurious frequencies: fEUT : EUT Operating Frequency Emission Limit (V/m) 1250(V/m) – 375(V/m) = [fEUT(MHz) – 260(MHz)] X + 375(V/m) 470(MHz) – 260(MHz) Other emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 20 dB below the level of the fundamental or comply with the radiated emissions limits specified in section 1 5.209(a) limit in the table below has to be followed. Note: (1) The tighter limit applies at the band edges. (2) Emission level (dBuV/m)=20log Emission level (uV/m). TRF No.: FCC 15.231/A Page 16 of 27 Report No.: ED151019050E Ver. 1.0

FCC Part15 (15.231) , Subpart C Fundamental Frequency Field Strength Field Strength of Spurious Of Fundamental Emissions 433.92MHz AV:80.82 dBuV/m at 3m AV:60.82 dBuV/m at 3m distance distance PK:100.82dBuV/m at 3m PK:80.82 dBuV/m at 3m distance distance Calculation of Average factor The average correction factor is computed by analyzing the on time in 100ms over one complete pulse train. Analysis of the remote transmitter on time in one complete pulse train, therefore the average value of fundamental frequency is: Average= Peak Value+20log(Duty Cycle), where the duty factor is calculated from following formula: The duty cycle is simply the on-time divided by the period: The duration of one cycle=0.902ms*6+0.306*3=6.33ms Effective period of the cycle=14.54ms Duty Cycle=(6.33ms)/14.54ms=0.435 Therefore, the averaging factor is found by 20log(0.435)=-7.23dB Pulse Width(PW)=0.306ms 2/PW=2/0.306=6.536KHz RBW=1MHz>2/PW(6.536KHz) Therefore PDCF is no needed Please see the test plot below: TRF No.: FCC 15.231/A Page 17 of 27 Report No.: ED151019050E Ver. 1.0

TRF No.: FCC 15.231/A Page 18 of 27 Report No.: ED151019050E Ver. 1.0

7.2.3 Measurement Result Modulation: ASK Test Date : November 10, 2015 Frequency Range: 1-25GHz Temperature : 25 ℃ Test Result: PASS Humidity : 50 % Measured Distance: 3m Test By: Andy Freq. Ant. Pol. Emission Level(dBuV/m) Limit 3m(dBuV/m) Margin(dB) (MHz) H/V PK AV PK AV PK AV 433.920(F) V 79.34 72.11 100.82 80.82 -21.48 -8.71 867.84 V 61.05 53.82 80.82 60.82 -19.77 -7.00 1301.76 V 59.42 52.19 80.82 60.82 -21.4 -8.63 1735.68 V 58.24 51.01 80.82 60.82 -22.58 -9.81 2169.6 V 57.36 50.13 80.82 60.82 -23.46 -10.69 2603.52 V 56.2 48.97 80.82 60.82 -24.62 -11.85 3037.44 V 55.48 48.25 80.82 60.82 -25.34 -12.57 433.920(F) H 78.62 71.39 100.82 80.82 -22.2 -9.43 867.84 H 60.35 53.12 80.82 60.82 -20.47 -7.70 1301.76 H 59.85 52.62 80.82 60.82 -20.97 -8.20 1735.68 H 58.42 51.19 80.82 60.82 -22.4 -9.63 2169.6 H 57.36 50.13 80.82 60.82 -23.46 -10.69 2603.52 H 56.62 49.39 80.82 60.82 -24.2 -11.43 3037.44 H 55.48 48.25 80.82 60.82 -25.34 -12.57 TRF No.: FCC 15.231/A Page 19 of 27 Report No.: ED151019050E Ver. 1.0

7.3 TRANSMISSION REQUIREMENT 7.3.1 Applicable Standard According to FCC Part 15.231(a) 7.3.2 Conformance Limit According to FCC Part 15.231(a) :In addition, devices operated under the provisions of this paragraph shall be provided with a means for automatically limiting operation so that the duration of each transmission shall not be greater than one second and the silent period between transmissions shall be at least 30 times the duration of the transmission but in no case less than 10 seconds. 7.3.3 Test Configuration Test according to clause 6.2 radio frequency test setup 2 7.3.4 Test Procedure The following table is the setting of spectrum analyzer. Spectrum analyzer Setting Attenuation Auto Span Frequency 0Hz RBW 1M VBW 1M Detector Peak Trace Max hold Sweep Time 10S a. The transmitter output (antenna port) was connected to the spectrum analyzer. b. Set RBW of spectrum analyzer to 1MHz and VBW to 1MHz, Set Detector to Peak, Trace to Max Hold. c. Set the span to 0Hz and the sweep time to 10s and record the value. 7.3.5 Test Results Temperature: 24℃ Test Date: November 10, 2015 Humidity: 53 % Test By: KK Test mode: TX Mode Frequency.(MHz) silent period between transmissions Limit Verdict 433.92 16.175ms 5 seconds PASS TRF No.: FCC 15.231/A Page 20 of 27 Report No.: ED151019050E Ver. 1.0

Transmitter Requirement Test Model Channel 0: 433.92MHz silent period between transmissions TRF No.: FCC 15.231/A Page 21 of 27 Report No.: ED151019050E Ver. 1.0

7.4 Antenna Application 7.4.1 Antenna Requirement For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 7.4.2 Result The EUT’s antenna is internal antenna, using a permanently attached antenna which is not replaceable. The antenna’s gain is 2.14dBi and meets the requirement. TRF No.: FCC 15.231/A Page 22 of 27 Report No.: ED151019050E Ver. 1.0

APPENDIX I (Photos of EUT) TRF No.: FCC 15.231/A Page 23 of 27 Report No.: ED151019050E Ver. 1.0

TRF No.: FCC 15.231/A Page 24 of 27 Report No.: ED151019050E Ver. 1.0

TRF No.: FCC 15.231/A Page 25 of 27 Report No.: ED151019050E Ver. 1.0

TRF No.: FCC 15.231/A Page 26 of 27 Report No.: ED151019050E Ver. 1.0

TRF No.: FCC 15.231/A Page 27 of 27 Report No.: ED151019050E Ver. 1.0


Document Created: 2015-12-30 10:24:08
Document Modified: 2015-12-30 10:24:08
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC