Test report

FCC ID: 2ACE5-NLC

Test Report

Download: PDF
FCCID_2872233

. Shenzhen CTL Testing Technology Co., Ltd. Tel: +86-755-89486194 Fax: +86-755-26636041 FCC PART 15 SUBPART C TEST REPORT FCC Part 15.247 Report Reference No......................: CTL1512303898-WF Compiled by ( position+printed name+signature)..: File administrators Jacky Chen Name of the organization performing the tests Test Engineer Tracy Qi ( position+printed name+signature)..: Approved by ( position+printed name+signature)..: Manager Tracy Qi Date of issue.....................................: Jan. 11, 2016 Test Firm..........................................: Shenzhen CTL Testing Technology Co., Ltd. Address.............................................: Floor 1-A, Baisha Technology Park, No.3011, Shahexi Road, Nanshan District, Shenzhen, China 518055 Applicant’s name............................: TELEPHONE EST (HK) CO., LTD Address.............................................: Room709,7F, FuLi tianhe commercial building,Linhe East Road and tianhe district, Guangzhou, China Test specification: Standard ...........................................: FCC Part 15.247: Operation within the bands 902–928 MHz, 2400– 2483.5 MHz, and 5725–5850 MHz. Master TRF.......................................: Dated 2011-01 Shenzhen CTL Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTL Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTL Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .................... : LED Display Board FCC ID…………………………….…..: 2ACE5-NLC Trade Mark .......................................: N/A Model/Type reference.......................: NLC Work frequency ................................: 2402~2480MHz Version..............................................: V4.0 Type of modulation ...........................: GFSK Antenna Gain ...................................: 0 dBi Antenna type ....................................: Chip Antenna Result................................................: Positive

V1.0 Page 2 of 34 Report No.: CTL1512303898-WF TEST REPORT Jan. 11, 2016 Test Report No. : CTL1512303898-WF ______________________________________________________________________________________________ Date of issue Equipment under Test : LED Display Board Model /Type : NLC Applicant : TELEPHONE EST (HK) CO., LTD Address : Room709,7F, FuLi tianhe commercial building,Linhe East Road and tianhe district, Guangzhou, China Manufacturer : TELEPHONE EST (HK) CO., LTD Address : Room709,7F, FuLi tianhe commercial building,Linhe East Road and tianhe district, Guangzhou, China Test Result according to the Positive standards on page 5: The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory.

V1.0 Page 3 of 34 Report No.: CTL1512303898-WF Contents 1. TEST STANDARDS .................................................................. 4 2. SUMMARY ............................................................................. 5 2.1. General Remarks 5 2.2. Equipment Under Test 5 2.3. Short description of the Equipment under Test (EUT) 5 2.4. EUT operation mode 5 2.5. EUT configuration 6 2.6. Configuration of Tested System 6 2.7. Related Submittal(s) / Grant (s) 6 2.8. Modifications 6 2.9. NOTE 6 2.10. Channel list 7 2.11. Mode of Operation 7 3. TEST ENVIRONMENT............................................................... 8 3.1. Address of the test laboratory 8 3.2. Test Facility 8 3.3. Environmental conditions 8 3.4. Statement of the measurement uncertainty 8 3.5. Test Description 9 3.6. Equipments Used during the Test 10 4. TEST CONDITIONS AND RESULTS ............................................ 11 4.1. AC Power Conducted Emission 11 4.2. Radiated Emission and band edge 14 4.3. Maximum Peak Output Power 19 4.4. 6dB Bandwidth 20 4.5. Power Spectral Density Measurement 22 4.6. Spurious RF Conducted Emission and band edge 24 4.7. Antenna Requirement 28 5. TEST SETUP PHOTOS OF THE EUT .......................................... 29 6. EXTERNAL AND INTERNAL PHOTOS OF THE EUT ....................... 31

V1.0 Page 4 of 34 Report No.: CTL1512303898-WF 1. TEST STANDARDS The tests were performed according to following standards: FCC Rules Part 15.247: Frequency Hopping, Direct Spread Spectrum and Hybrid Systems that are in operation within the bands of 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz. ANSI C63.10-2013: American National Standard for Testing Unlicensed Wireless Devices KDB Publication No. KDB 558074 D01 v03r03 Guidance on Measurements for Digital Transmission Systems ANSI C63.4-2014

V1.0 Page 5 of 34 Report No.: CTL1512303898-WF 2. SUMMARY 2.1. General Remarks Date of receipt of test sample : Dec. 30, 2015 Testing commenced on : Jan. 11, 2016 Testing concluded on : Jan. 11, 2016 2.2. Equipment Under Test Power supply system utilised Power supply voltage : ○ 120V / 60 Hz ○ 115V / 60Hz ○ 12 V DC ○ 24 V DC ● Other (specified in blank below) DC 5V from USB 2.3. Short description of the Equipment under Test (EUT) LED Display Board with Bluetooth 4.0LE function. For more details, refer to the user’s manual of the EUT. Serial number: Prototype 2.4. EUT operation mode The EUT has been tested under typical operating condition. The Applicant provides communication tools software to control the EUT for staying in continuous transmitting and receiving mode for testing. There are 40 channels of EUT, and the test carried out at the lowest channel, middle channel and highest channel . Frequency Range: 2400-2483.5MHz Channel number: 40 channels Modulation type: GFSK Antenna: Chip Antenna Test Channel Test Frequency Low Channel 2402 MHz Middle Channel 2440 MHz High Channel 2480 MHz

V1.0 Page 6 of 34 Report No.: CTL1512303898-WF 2.5. EUT configuration The following peripheral devices and interface cables were connected during the measurement: ○ - supplied by the manufacturer ● - supplied by the lab ● Notebook PC Manufacturer : DELL Model No. : PP18L 2.6. Configuration of Tested System Fig. 2-1 Configuration of Tested System Note Book PC EUT Table 2-1 Equipment Used in Tested System No. Product Manufacturer Model No. Serial No. FCC ID 1 Notebook PC DELL PP18L ------ E2KWM3945ABG 2.7. Related Submittal(s) / Grant (s) This submittal(s) (test report) is intended for FCC ID: 2ACE5-NLC filing to comply with Section 15.247 of the FCC Part 15, Subpart C Rules. 2.8. Modifications No modifications were implemented to meet testing criteria. 2.9. NOTE 1. The EUT have Bluetooth 4.0 functions,The functions of the EUT listed as below: Test Standards Reference Report BT 4.0LE FCC Part 15 Subpart C (Section15.247) CTL1512303898-WF 2. The frequency bands used in this EUT are listed as follows: Frequency Band(MHz) 2400-2483.5 5150-5350 5470-5725 5725-5850 BT 4.0LE √ － － － 3. The EUT provides one completed transmitter and receiver. Modulation Mode TX Function BT 4.0LE 1TX

V1.0 Page 7 of 34 Report No.: CTL1512303898-WF 2.10. Channel list Frequency Frequency Channel Channel (MHz) (MHz) 00 2402 20 2442 01 2404 21 2444 02 2406 22 2446 03 2408 23 2448 04 2410 24 2450 05 2412 25 2452 06 2414 26 2454 07 2416 27 2456 08 2418 28 2458 09 2420 29 2460 10 2422 30 2462 11 2424 31 2464 12 2426 32 2466 13 2428 33 2468 14 2430 34 2470 15 2432 35 2472 16 2434 36 2474 17 2436 37 2476 18 2438 38 2478 19 2440 39 2480 2.11. Mode of Operation 1. The EUT has been tested under normal operating condition. 2. Test program used to control the EUT for staying in continuous transmitting and receiving mode is programmed. Channel low (2402MHz), mid (2440MHz) and high (2480MHz) with highest data rate are chosen for full testing.

V1.0 Page 8 of 34 Report No.: CTL1512303898-WF 3. TEST ENVIRONMENT 3.1. Address of the test laboratory Shenzhen CTL Testing Technology Co., Ltd. Floor 1-A, Baisha Technology Park, No.3011, Shahexi Road, Nanshan District, Shenzhen, China 518055 The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.10 (2013) and CISPR Publication 22. 3.2. Test Facility The test facility is recognized, certified, or accredited by the following organizations: IC Registration No.: 9618B The 3m alternate test site of Shenzhen CTL Testing Technology Co., Ltd. EMC Laboratory has been registered by Certification and Engineer Bureau of Industry Canada for the performance of with Registration No.: 9618B on November 13, 2013. FCC-Registration No.: 970318 Shenzhen CTL Testing Technology Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration 970318, December 19, 2013. 3.3. Environmental conditions During the measurement the environmental conditions were within the listed ranges: Temperature: 15-35 ° C Humidity: 30-60 % Atmospheric pressure: 950-1050mbar 3.4. Statement of the measurement uncertainty The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was calculated for all measurements listed in this test report acc. to CISPR 16 - 4 „Specification for radio disturbance and immunity measuring apparatus and methods – Part 4: Uncertainty in EMC Measurements“ and is documented in the Shenzhen CTL Testing Technology Co., Ltd. quality system acc. to DIN EN ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the device. Hereafter the best measurement capability for CTL laboratory is reported: Measurement Test Range Notes Uncertainty Radiated Emission 30~1000MHz 4.10dB (1) Radiated Emission Above 1GHz 4.32dB (1) Conducted Disturbance 0.15~30MHz 3.20dB (1) (1) This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2.

V1.0 Page 9 of 34 Report No.: CTL1512303898-WF 3.5. Test Description FCC PART 15 FCC Part 15.207 AC Power Conducted Emission N/A FCC Part 15.247(a)(2) 6dB Bandwidth PASS FCC Part 15.247(d) Spurious RF Conducted Emission PASS FCC Part 15.247(b) Maximum Peak Output Power PASS FCC Part 15.247(e) Power Spectral Density PASS FCC Part 15.109/ 15.205/ 15.209 Radiated Emissions PASS FCC Part 15.247(d) Band Edge Compliance of RF Emission PASS FCC Part 15.203/15.247 (b) Antenna Requirement PASS FCC Per 47 CFR 2.1091(b) MPE Evaluation PASS Remark: The measurement uncertainty is not included in the test result.

V1.0 Page 10 of 34 Report No.: CTL1512303898-WF 3.6. Equipments Used during the Test Calibration Calibration Test Equipment Manufacturer Model No. Serial No. Date Due Date ULTRA-ROADBAND Sunol Sciences JB1 A061713 2015/06/02 2016/06/01 ANTENNA Corp. EMI Test Receiver R&S ESCI 103710 2015/06/02 2016/06/01 Spectrum Analyzer Agilent E4407B MY41440676 2015/05/21 2016/05/20 Controller Controller EM Electronics N/A 2015/05/21 2016/05/20 EM 1000 Sunol Sciences Horn Antenna DRH-118 A062013 2015/05/19 2016/05/18 Corp. Active Loop Antenna Daze ZN30900A N/A 2015/05/19 2016/05/18 LISN R&S ENV216 3560.6550.12 2015/06/02 2016/06/01 LISN R&S ESH2-Z5 860014/010 2015/06/02 2016/06/01 F-071115- ISN FCC 11229 2015/05/19 2016/05/18 1057-1-09 Amplifier Agilent 8349B 3008A02306 2015/05/19 2016/05/18 Amplifier Agilent 8447D 2944A10176 2015/05/19 2016/05/18 Transient Limiter SCHWARZCECK VTSD 9561F 9666 2015/06/02 2016/06/01 Radio Communication R&S CMU200 115419 2015/05/22 2016/05/21 Tester Temperature/Humidity Gangxing CTH-608 02 2015/05/20 2016/05/19 Meter SIGNAL Agilent E4421B US40051744 2015/05/20 2016/05/19 GENERATOR Wideband Peak Power Anritsu ML2495A 220.23.35 2015/05/20 2016/05/19 Meter Climate Chamber ESPEC EL-10KA A20120523 2015/05/20 2016/05/19 9SH10- High-Pass Filter K&L 2700/X12750 N/A 2015/05/20 2016/05/19 -O/O 41H10- High-Pass Filter K&L 1375/U12750 N/A 2015/05/20 2016/05/19 -O/O RF Cable HUBER+SUHNER RG214 N/A 2015/05/20 2016/05/19

V1.0 Page 11 of 34 Report No.: CTL1512303898-WF 4. TEST CONDITIONS AND RESULTS 4.1. AC Power Conducted Emission TEST CONFIGURATION TEST PROCEDURE 1 The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. The EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.10-2013. 2 Support equipment, if needed, was placed as per ANSI C63.10-2013 3 All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10-2013 4 The EUT received DC5V power from the adapter, the adapter received AC120V/60Hz power through a Line Impedance Stabilization Network (LISN) which supplied power source and was grounded to the ground plane. 5 All support equipments received AC power from a second LISN, if any. 6 The EUT test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. 7 Analyzer / Receiver scanned from 150 KHz to 30MHz for emissions in each of the test modes. 8 During the above scans, the emissions were maximized by cable manipulation. Conducted emissions were investigated over the frequency range from 0.15MHz to 30MHz using a receiver bandwidth of 9kHz. AC Power Conducted Emission Limit For intentional device, according to § 15.207(a) AC Power Conducted Emission Limits is as following： Maximum RF Line Voltage (dBμV) Frequency (MHz) CLASS A CLASS B Q.P. Ave. Q.P. Ave. 0.15 - 0.50 79 66 66-56* 56-46* 0.50 - 5.00 73 60 56 46 5.00 - 30.0 73 60 60 50 * Decreasing linearly with the logarithm of the frequency TEST RESULTS

scan zmsme "Voltage (9K—30M)FIN® Shore pes tever@a zo oo To: soor sooc somm in o ow an son ow row zow 3o Freauency zl es uzasurEmznz resunT: "crm160106650_fin" 8 m on eup eup eup eup eup uzasurEmzNz resunT: "crm160106650_fin2" a/s & 8 eup aian ie ie eup eup cup eup eup t

vi.0 Page 13 of 34 Report No.: CTL1512303808—WF scan zmsme "Voltace (9K—30M)FIN® Shore pes 1 ltage tever en zo so so ao 2o 2o 10 o o oo Toor. o0% —soor somm im o ow an son ow row Frequency 2 a x anes e uzasurEmzNz mEsuT: "Cr160106651_fin" 1/ Zransa 24 eup eup eup eup eup cup 6 00 00 o ueasurenznz mesunt: 1/6/2 eup eup eup cup eup eup

V1.0 Page 14 of 34 Report No.: CTL1512303898-WF 4.2. Radiated Emission and band edge TEST CONFIGURATION Radiated Emission Test Set-Up Frequency range 9KHz – 30MHz Turntable Loop antenna EUT 3m Test 0.8 m Receiver Ground Plane Coaxial Cable Frequency range 30MHz – 1000MHz 3m Turntable 1m to 4m EUT Test Receiver 0.8m Ground Plane Coaxial Cable Frequency range above 1GHz-25GHz

V1.0 Page 15 of 34 Report No.: CTL1512303898-WF TEST PROCEDURE 1 The EUT was placed on a turn table which is 0.8m above ground plane. 2 Maximum procedure was performed by raising the receiving antenna from 1m to 4m and rotating the turn table from 0℃ to 360℃ to acquire the highest emissions from EUT 3. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 4. Repeat above procedures until all frequency measurements have been completed. 5. the fundamental frequency is 2400-2483.5MHz, So the radiation emissions frequency range were tested from 9KHz to 25GHz. Field Strength Calculation The field strength is calculated by adding the Antenna Factor and Cable Factor and subtracting the Amplifier Gain and Duty Cycle Correction Factor(if any) from the measured reading. The basic equation with a sample calculation is as follows: FS = RA + AF + CL – AG Where FS = Field Strength CL = Cable Attenuation Factor (Cable Loss) RA = Reading Amplitude AG = Amplifier Gain AF = Antenna Factor For example Frequency FS RA AF CL AG Transd (MHz) (dBμV/m) (dBμV/m) (dB) (dB) (dB) (dB) 300.00 40 58.1 12.2 1.6 31.90 -18.1 Transd=AF +CL-AG RADIATION LIMIT For intentional device, according to § 15.209(a), the general requirement of field strength of radiated emission from intentional radiators at a distance of 3 meters shall not exceed the following table. According to § 15.247(d), in any 100kHz bandwidth outside the frequency band in which the EUT is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20dB below that in the100kHz bandwidth within the band that contains the highest level of desired power. Frequency Distance Radiated Radiated (MHz) (Meters) (dBμV/m) (μV/m) 30-88 3 40.0 100 88-216 3 43.5 150 216-960 3 46.0 200 Above 960 3 54.0 500

V1.0 Page 16 of 34 Report No.: CTL1512303898-WF TEST RESULTS Below 1GHz: The radiated measurement are performed the each test mode and channel (low/mid/high), the datum recorded below is the worst case for all the test mode and channel.

sWEEP TABLE: "test (3OM—1G)" shore Description: rie staze weas . in mransa Zine Bandv. kne cei 2o zo so so ao zo 2o 10 o sow aow som: com 7om Toom zoom 3oow «ow soon soom soom: 10 Freqvencyl zen 11.zee uznsurzuzNt mEsUDT: "CTL160107011_zed" 177 «2a ERREERE

V1.0 Page 18 of 34 Report No.: CTL1512303898-WF Reading Measure Frequency Factor Limit Margin CH Antenna Level Level Detector (MHz) (dB) (dBuV/m) (dB) (dBuV/m) (dBuV/m) V 2402 61.4 29.1 90.5 Fundamental / PK V 3200 13.6 31.1 44.7 54(note3) 9.3 PK V 2390 36.3 32.2 68.5 74 5.5 PK V 2390 13.9 32.2 46.1 54 7.9 AV V 2400 37.7 32.1 69.8 74 4.2 PK 0 V 2400 15.2 32.1 47.3 54 6.7 AV V 4804 3.6 42.6 46.2 54(note3) 7.8 PK V 7206 21.4 46.5 67.9 74 6.1 PK V 7206 -0.8 46.5 45.7 54 8.3 AV H 24000 11.7 38.9 50.6 54 3.4 PK V 2440 60.4 30.7 91.1 Fundamental / PK V 3200 13.1 31.1 44.2 54(note3) 9.8 PK V 4880 14.8 32.8 47.6 54(note3) 6.4 PK 19 V 7320 19.9 46.8 66.7 74 7.3 PK V 7320 0.5 46.1 46.6 54 7.4 AV H 24000 11.7 38.9 50.6 54 3.4 PK V 2480 60.7 29.5 90.2 Fundamental / PK V 3200 14.7 31.1 45.8 54(note3) 8.2 PK V 2483.5 35.2 30.2 65.4 74 8.6 PK V 2483.5 13.9 30.2 44.1 54 9.9 AV 39 V 4960 15.3 32.5 47.8 54(note3) 6.2 PK V 7440 22.3 46.3 68.6 74 5.4 PK V 7440 -0.6 46.3 45.7 54 8.3 AV H 24000 11.7 38.9 50.6 54 3.4 PK Note: 1. Measure Level = Reading Level + Factor. 2. The test results which are attenuated more than 20 dB below the permissible value limit (the test frequency range: 9kHz~30MHz, 18GHz~25GHz), therefore no data appear in the report. 3. This limit applies for using average detector, if the test result on peak is lower than average limit, then average measurement needn’t be performed. Remark: RBW 1MHz VBW 3MHz peak detector for PK value, RMS detector for AV value

V1.0 Page 19 of 34 Report No.: CTL1512303898-WF 4.3. Maximum Peak Output Power TEST CONFIGURATION SPECTRUM EUT ANALYZER TEST PROCEDURE According to C63.10 -2013 and KDB 558074 D01 v03r03,The EUT was directly connected to the power meter / spectrum analyzer and antenna output port as show in the block diagram as TEST CONFIGURATION shows. Use the wideband power meter to test peak power and record the result. LIMIT The Maximum Peak Output Power Measurement limit is 30dBm. TEST RESULTS Channel No. Frequency Measurement Power Output Limit Result (MHz) (dBm) (dBm) 0 2402 -5.02 30.00 Pass 19 2440 -4.81 30.00 Pass 39 2480 -4.94 30.00 Pass

V1.0 Page 20 of 34 Report No.: CTL1512303898-WF 4.4. 6dB Bandwidth TEST CONFIGURATION SPECTRUM EUT ANALYZER TEST PROCEDURE 1. The testing follows FCC KDB Publication No. 558074 D01 v03r03 (Measurement Guidelines of DTS). 2. The RF output of EUT was connected to the spectrum analyzer by a low loss cable. 3. Make the measurement with the spectrum analyzer's resolution bandwidth (RBW) = 100 kHz. In order to make an accurate measurement, set the span greater than RBW. The 6 dB bandwidth must be greater than 500 kHz. 4. The marker-delta reading at this point is the 6 dB bandwidth of the emission. LIMIT For digital modulation systems, the minimum 6 dB bandwidth shall be at least 500 kHz. TEST RESULTS CHANNEL 6dB BANDWIDTH LIMIT FREQUENCY (KHz) (KHz) PASS/FAIL (MHz) 2402 740.2 500 PASS 2440 765.3 500 PASS 2480 744.1 500 PASS Low Channel

V1.0 Page 21 of 34 Report No.: CTL1512303898-WF Middle Channel High Channel

V1.0 Page 22 of 34 Report No.: CTL1512303898-WF 4.5. Power Spectral Density Measurement TEST CONFIGURATION SPECTRUM EUT ANALYZER TEST PROCEDURE The EUT was tested according to KDB 558074 D01 v03r03 for compliance to FCC 47CFR 15.247 requirements. Set RBW= 3 kHz, VBW≥10KHz, SPAN to 1.5 times greater than the EBW,. LIMIT For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. TEST RESULTS Channel PSD Maximum Modulation Channel Frequency limit PASS / FAIL Mode (dBm/3KHz) (MHz) (dBm/3KHz) 1 2402 -15.448 8 PASS GFSK 19 2440 -16.035 8 PASS 39 2480 -15.957 8 PASS Low channel

V1.0 Page 23 of 34 Report No.: CTL1512303898-WF Middle channel High channel

V1.0 Page 24 of 34 Report No.: CTL1512303898-WF 4.6. Spurious RF Conducted Emission and band edge TEST CONFIGURATION SPECTRUM EUT ANALYZER TEST PROCEDURE The EUT was tested according to KDB 558074 D01 v03r03 for compliance to FCC 47CFR 15.247 requirements. The Spurious RF conducted emissions compliance of RF radiated emission should be measured by following the guidance in ANSI C63.10-2013 with respect to maximizing the emission by rotating the EUT, measuring the emission while the EUT is situated in three orthogonal planes (if appropriate), adjusting the measurement antenna height and polarization etc. Set RBW=100kHz and VBM= 300KHz to measure the peak field strength , and measure frequeny range from 30MHz to 26.5GHz. LIMIT In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. TEST RESULTS Low channel

V1.0 Page 25 of 34 Report No.: CTL1512303898-WF Middle channel

V1.0 Page 26 of 34 Report No.: CTL1512303898-WF High channel

V1.0 Page 27 of 34 Report No.: CTL1512303898-WF

V1.0 Page 28 of 34 Report No.: CTL1512303898-WF 4.7. Antenna Requirement Standard Applicable For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section 15.247 (c), if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. Refer to statement below for compliance. The manufacturer may design the unit so that the user can replace a broken antenna, but the use of a standard antenna jack or electrical connector is prohibited. Further, this requirement does not apply to intentional radiators that must be professionally installed. Antenna Connected Construction The antenna used in this product is Chip Antenna, The directional gains of antenna used for transmitting is 0dBi.

V1.0 Page 29 of 34 Report No.: CTL1512303898-WF 5. Test Setup Photos of the EUT

V1.0 Page 30 of 34 Report No.: CTL1512303898-WF

V1.0 Page 31 of 34 Report No.: CTL1512303898-WF 6. External and Internal Photos of the EUT External Photos of EUT

V1.0 Page 32 of 34 Report No.: CTL1512303898-WF

V1.0 Page 33 of 34 Report No.: CTL1512303898-WF Internal Photos of EUT

V1.0 Page 34 of 34 Report No.: CTL1512303898-WF ......................End of Report.......................


Document Created: 2016-01-13 09:17:26
Document Modified: 2016-01-13 09:17:26
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC