Users Manual

FCC ID: 2ACDZ-WT1HBS05

Users Manual

Download: PDF
FCCID_2604108

USER MANUAL_V1 The device is a fully self‐contained small form‐factor, single stream, 802.11 b/g/n wifi module, which provides a wireless interface to any equipment with a UART interface for data transfer. It supports AP and STA wireless networking and support WIFI Direct mode. It integrates MAC, baseband processor, RF transceiver with power amplifier in hardware and all wifi protocol and configuration functionality and networking stack, in embedded firmware to make a fully self‐contained 802.11 b/g/n wifi solution for a variety of applications. Device Features Single stream WIFI @2.4G with support for WEP security mode as well as WPA/WPA2 Fully self‐contained serial‐to‐wireless functionality Support IEEE802.11 b/g/n wireless standards Support work as STA/AP Support smart configuration Support PCB/External antenna option Small size:49.6mm x 31mm x 4mm Device paremeters Class Item Parameters Wireless Wireless standard 802.11 b/g/n Frequency range 2.412GHz~2.472GHz For CE 2.412GHz~2.462GHz For FCC Transmit Power 802.11b:16dBm 802.11g:14dBm 802.11n:13dBm Receiver Sensitivity 802.11b<‐78dBm 802.11g<‐68dBm 802.11n<‐66dBm PCB antenna gain 2dB Hardware Operating voltage 5V Operating current Max(tx):~240mA OPERATING temp ‐10~70℃ size 49.6mm x 31mm x 4mm VIL ≤0.3VCC VIH ≥0.7VCC ESD(Human Body Model) 2kv@25℃ ESD(Charged Device Model) 500v@25℃ software Network type STA/AP Security mechanisms WEP/WPA/WAP2 Encryption WEP64/WEP128/TKIP/AES Reserved resource

Network protocol IPv4,TCP/UDP/DNS/DHCP Hardware (Unit: mm) Pin assignment Pin Pin name Description Type Note Pin4 VDD VCC 5V POWER Pin3 GND GND POWER UART0 Pin2 UART0_TX UART0_TX O Only for Passthrough Pin1 UART0_RX UART0_RX I

XY Plot 3 HFSSModel1 ANSOFT -7.50 Curve Info dB(St(Box6_T1,Box6_T1)) Setup1 : Sw eep -10.00 -12.50 dB(St(Box6_T1,Box6_T1)) -15.00 -17.50 -20.00 -22.50 -25.00 2.38 2.40 2.42 2.44 2.46 2.48 2.50 2.52 Freq [GHz] The device also supports external antenna. The parameters required are as followed: Frequency range 2.4G~2.5G Impedance 50Ohm VSWR <2 Return loss <‐10dB Connector type IPEX Information to be supplied to the end user by the OEM or Integrator The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating the Inter® wireless adapter, In compliance with local regulations. Host system must be labeled with “Contains FCC ID: 2ACDZ‐WT1HBS05”, FCC ID displayed on label.

Warning 1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 3. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. It must be used at least 20cm away from the body of the user.


Document Created: 2015-05-04 14:18:14
Document Modified: 2015-05-04 14:18:14
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC