I18Z60073-SEM04_SAR_Rev0_part9

FCC ID: 2ACCJN026

RF Exposure Info

Download: PDF
FCCID_3856404

DASY5 Validation Report for Head TSL Date: 20.07.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2600 MHz; Type: D2600V2; Serial: D2600V2 — SN: 1012 Communication System: UID 0 — CW; Frequency: 2600 MHz Medium parameters used: f = 2600 MHz; 0 = 2.04 S/m; & = 37.2; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvF(7.96, 7.96, 7.96); Calibrated: 31.05.2017; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 28.03.2017 & Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 e DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 113.6 V/m; Power Drift = 0.05 dB Peak SAR (extrapolated) = 32.3 W/kg SAR(1 g) = 14.9 W/kg; SAR(10 g) = 6.57 W/kg Maximum value of SAR (measured) = 25.0 W/kg dB 0 —5.00 —10.00 —15.00 —20.00 —25.00 0 dB = 25.0 W/kg = 13.98 dBW/kg Certificate No: D2600V2—1012_Jul17 Page 5 of 8

® Impedance Measurement Plot for Head TSL 20 Jul 2017 12:14:05 CHI) sii 1 U FS 5: 46.936 a —5.0410 a 12.143 pF 2 600.000 000 MHz ~~3—— Del Ca Av 16 * H1d CH2 Ca Av 16 * H1d START 2 400.000 000 MHz STOP 2 800.000 000 MHz Certificate No: D2600V2—1012_Jul17 Page 6 of 8

) n S (\I DASY5 Validation Report for Body TSL Date: 21.07.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2600 MHz; Type: D2600V2; Serial: D2600V2 — SN: 1012 Communication System: UID 0 — CW; Frequency: 2600 MHz Medium parameters used: f = 2600 MHz; 0 = 2.22 S/m; & = 51.6; p = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN7349; ConvF(7.94, 7.94, 7.94); Calibrated: 31.05.2017; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 28.03.2017 * Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 & DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 106.6 V/m; Power Drift = —0.07 dB Peak SAR (extrapolated) =30.1 W/kg SAR(I g) = 14.1 W/kg; SAR(10 g) = 6.25 W/kg Maximum value of SAR (measured) = 23.4 W/kg —5.20 —10.40 ~15.60 —20.80 —26.00 0 dB = 23.4 W/kg = 13.69 dBW/kg Certificate No: D2600V2—1012_Jul17 Page 7 of 8

© Impedance Measurement Plot for Body TSL 241 Jul 2017 14:S50:41 §11 i U Fs 1143.541 a —5.3223 6 14.501 pF 2 600.000 000 MHz t Av 16 . H1d CH2 Ca fivg 16 H1d START 2 400.000 000 MHz STOP 2 800.000 000 MHz Certificate No: D2600V2—1012_Jul17 Page 8 of 8

) a S (I Calibration Laboratory of \L\'y'/ S Schweizerischer Kalibrierdienst 2 8 Schmid & Partner ww {) y Cc Service suisse d‘étalonnage $ Engineering AG Servizio svizzero di taratura hi wl Zeughausstrasse 43, 8004 Zurich, Switzerland 4/ CS S Swiss Calibration Service Undoctue®® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client CTTL—BJ (Auden) Certificate No: D5GHzV2—1060_Jul17 [CALIBRATION CERTIFICATE Object D5GHzV2 — SN:1060 Calibration procedure(s) QA CAL—22.v2 Calibration procedure for dipole validation kits between 3—6 GHz Calibration date: July 25, 2017 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical forcalibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 04—Apr—17 (No. 217—02521/02522) Apr—18 Power sensor NRP—Z91 SN: 103244 04—Apr—17 (No. 217—02521) Apr—18 Power sensor NRP—Z91 SN: 103245 04—Apr—17 (No. 217—02522) Apr—18 Reference 20 dB Attenuator SN: 5058 (20k) 07—Apr—17 (No. 217—02528) Apr—18 Type—N mismatch combination SN: 5047.2 / 06327 07—Apr—17 (No. 217—02529) Apr—18 Reference Probe EX3DV4 SN: 3503 31—Dec—16 (No. EX3—3503_Dec16) Dec—17 DAE4 SN: 601 28—Mar—17 (No. DAE4—601_Mar17) Mar—18 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter EPM—442A SN: GB37480704 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: US37202783 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: MY41092317 07—Oct—15 (in house check Oct—16) In house check: Oct—18 RF generator R&S SMT—06 SN: 100972 15—Jun—15 (in house check Oct—16) In house check: Oct—18 Network Analyzer HP 8753E SN: US37390585 18—Oct—01 (in house check Oct—16) In house check: Oct—17 Name Function Signature Calibrated by: Johannes Kurikka Laboratory Technician Approved by: Katja Pokovie Technical Manager //4 Issued: July 27, 2017 This calibration certificate shall not be reproduced exceptin full without written approval of the laboratory. Certificate No: D5GHzV2—1060_Jul17 Page 1 of 16

® + & Calibration Laboratory of Schmid & Partner Engineering AG Zeughausstrasse 43, 8004 Zurich, Switzerland M wm sls gzre {'/,,47/?\\‘\\\\3 g Schweizerischer Kalibrierdienst C 5 Service suisse d‘étalonnage Servizio svizzero di taratura Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvrF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented paralle! to the body axis. Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D5GHzV2—1060_Jul17 Page 2 of 16

Measurement Conditions DASY system configuration, as far as not iven on page 1. DASY Version DASYS V52.10.0 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V5.0 Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy = 4.0 mm, dz =1.4 mm Graded Ratio = 1.4 (Z direction) 5200 MHz + 1 MHz 5300 MHz £ 1 MHz Frequency 5500 MHz # 1 MHz 5600 MHz * 1 MHz 5800 MHz +1 MHz Head TSL parameters at 5200 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 36.0 4.66 mho/m Measured Head TSL parameters (22.0 £0.2) °C 36.3 +6 % 4.51 mho/m + 6 % Head TSL temperature change during test <0.5 °C m~+ we«« SAR result with Head TSL at 5200 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.05 W/kg SAR for nominal Head TSL parameters normalized to 1W 80.6 W/kg # 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.30 W/kg SAR for nominal Head TSL parameters normalized to 1W 23.0 Wikg + 19.5 % (k=2) Head TSL parameters at 5300 MHz The followingparameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.9 4.76 mho/m Measured Head TSL parameters (22.0 £0.2) °C 36.1 26 % 4.61 mho/m +6 % Head TSL temperature change during test «0.5 °C SAR result with Head TSL at 5300 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.38 W/kg SAR for nominal Head TSL parameters normalized to 1W 83.8 W / kg x 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 240 Wikg SAR for nominal Head TSL parameters normalized to 1W 24.0 Wikg + 19.5 % (k=2) Certificate No: DSGHzV2—1060_Jul17 Page 3 of 16

(flélll} w Head TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.6 4.96 mho/m Measured Head TSL parameters (22.0 £0.2) °C 35.8 + 6 % 4.81 mho/m 6 % Head TSL temperature change during test <0.5 °C ———— ———— SAR result with Head TSL at 5500 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.48 Wikg SAR for nominal Head TSL parameters normalized to 1W 84.8 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 241 Wikg SAR for nominal Head TSL parameters normalized to 1W 24.1 Wikg + 19.5 % (k=2) Head TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.5 5.07 mho/m Measured Head TSL parameters (22.0 £0.2) °C 35.7 +6 % 4.92 mho/m +6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL at 5600 MHz SAR averaged over 1 cm‘* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.45 W/kg SAR for nominal Head TSL parameters normalized to 1W 84.5 Wikg * 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.41 Wikg SAR for nominal Head TSL parameters normalized to 1W 24.1 Wikg # 19.5 % (k=2) Certificate No: DSGHzV2—1060_Jul17 Page 4 of 16

Head TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.3 5.27 mho/m Measured Head TSL parameters (22.0 £0.2) °C 35.4 +6 % 5.14 mho/m + 6 % Head TSL temperature change during test <0.5 °C ~—— SAR result with Head TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 100 mW input power 8.10 W/kg SAR for nominal Head TSL parameters normalized to 1W 80.9 W/kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 2.29 Wikg SAR for nominal Head TSL parameters normalized to 1W 22.9 W/kq # 19.5 % (k=2) Certificate No: D5GHzV2—1060_Jul17 Page 5 of 16

) S Body TSL parameters at 5200 MHz The following parameters and calculations were applied. Nominal Body TSL parameters Measured Body TSL parameters Temperature 22.0 °C (22.0 + 0.2) °C Permittivity 49.0 47 4 16 % Conductivity 5.30 mho/m 5.45 mho/m + 6 % Body TSL temperature change during test <0.5 °C _ SAR result with Body TSL at 5200 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.56 W/kg SAR for nominal Body TSL parameters normalized to 1W 75.1 Wikg # 19.9 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL condition SAR measured 100 mW input power 2.13 W/kg SAR for nominal Body TSL parameters normalized to 1W 21.1 Wikg + 19.5 % (k=2) Body TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.9 5.42 mho/m Measured Body TSL parameters (22.0 2 0.2) °C 47.2 26 % 5.58 mho/m + 6 % Body TSL temperature change during test <0.5 °C ~—— m SAR result with Body TSL at 5300 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.75 Wikg SAR for nominal Body TSL parameters normalized to 1W 77.0 Wikg # 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 218 Wikg SAR for nominal Body TSL parameters normalized to 1W 21.6 Wikg + 19.5 % (k=2) Certificate No: D5GHzV2—1060_Jul17 Page 6 of 16

) n N (II Body TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0°C 48.6 5.65 mho/m Measured Body TSL parameters (22.0 £0.2) °C 46.9 + 6 % 5.85 mho/m + 6 % Body TSL temperature change during test <0.5 °C ~—— SAR result with Body TSL at 5500 MHz SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 100 mW input power 8.19 Wikg SAR for nominal Body TSL parameters normalized to 1W 81.4 W/kg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.27 Wikg SAR for nominal Body TSL parameters normalized to 1W 22.5 W/kg + 19.5 %(k=2) Body TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.5 5.77 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 46.7 6 % 5.99 mho/m + 6 % Body TSL temperature change during test <0.5 °C ——— SAR result with Body TSL at 5600 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 8.10 W/ikg SAR for nominal Body TSL parameters normalized to 1W 80.5 Wikg + 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.28 Wikg SAR for nominal Body TSL parameters normalized to 1W 22.6 W/kg x 19.5 % (k=2) Certificate No: DSGHzV2—1060_Jul17 Page 7 of 16

m© I /7‘ F uy Body TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.2 6.00 mho/m Measured Body TSL parameters (22.0 £0.2) °C 46.4 x 6 % 6.28 mho/m + 6 % Body TSL temperature change during test <0.5 °C »——— ~—— SAR result with Body TSL at 5800 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 7.84 Wikg SAR for nominal Body TSL parameters normalized to 1W 78.0 Wikg * 19.9 %(k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.19 W/kg SAR for nominal Body TSL parameters normalized to 1W 21.7 W/kg + 19.5 % (k=2) Certificate No: D5GHzV2—1060_Jul17 Page 8 of 16

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL at 5200 MHz Impedance, transformed to feed point 50.5 Q — 6.6 jQ Return Loss —23.7 dB Antenna Parameters with Head TSL at 5300 MHz Impedance, transformed to feed point 47.5 Q — 2.8 jQ Return Loss — 28.3 dB Antenna Parameters with Head TSL at 5500 MHz Impedance, transformed to feed point 51.1 Q — 3.7 jQ Return Loss —28.5 dB Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point 54.0 Q + 2.0 jQ Return Loss —27.4 dB Antenna Parameters with Head TSL at 5800 MHz Impedance, transformed to feed point 52.3 Q — 2.9 jQ Return Loss — 28.9 dB Antenna Parameters with Body TSL at 5200 MHz Impedance, transformed to feed point 49.7 O — 4.7 jQ Return Loss —26.5 dB Antenna Parameters with Body TSL at 5300 MHz Impedance, transformed to feed point 46.8 Q — 1.9 jQ Return Loss — 28.3 dB Antenna Parameters with Body TSL at 5500 MHz Impedance, transformed to feed point 50.7 0 — 2.2 jQ Return Loss — 82.8 dB Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point 55.1 Q + 1.2 jQ. Return Loss —26.1 dB Certificate No: D5GHzV2—1060_Jul17 Page 9 of 16

® Antenna Parameters with Body TSL at 5800 MHz Impedance, transformed to feed point Return Loss 52.5 Q — 1.9 jQ — 80.1 dB General Antenna Parameters and Design Electrical Delay (one direction) _ 1.202 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in orderto improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend orthe soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on November 27, 2006 Certificate No: DSGHzV2—1060_Jul17 Page 10 of 16

m® I @TTL u uy DASY5 Validation Report for Head TSL Date: 25.07.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole DSGHzV2; Type: D5SGHzV2; Serial: D5SGHzV2 — SN:1060 Communication System: UID 0 — CW; Frequency: 5200 MHz, Frequency: 5300 MHz, Frequency: 5500 MHz, Frequency: 5600 MHz, Frequency: 5800 MHz Medium parameters used: f = 5200 MHz; 0 = 4.51 S/m; & = 36.3; p = 1000 kg/m* , Medium parameters used: £= 5300 MHz; 0 = 4.61 S/m; & = 36.1; p = 1000 kg/m> , Medium parameters used: £= 5500 MHz; 0 = 4.81 S/m; s = 35.8; p = 1000 kg/m* , Medium parameters used: f = 5600 MHz; 0 = 4.92 S/m; & = 35.7; p = 1000 kg/m* , Medium parameters used: f = 5800 MHz; 0 = 5.14 S/m; & = 35.4; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN3503; ConvF(5.76, 5.76, 5.76); Calibrated: 31.12.2016, ConvF(5.35, 5.35, 5,35); Calibrated: 31.12.2016, ConvF(5.2, 5.2, 5.2); Calibrated: 31.12.2016, ConvF(5.09, 5.09, 5.09); Calibrated: 31.12.2016, ConvF(5.01, 5.01, 5.01); Calibrated: 31.12.2016; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) + Electronics: DAE4 $n601; Calibrated: 28.03.2017 * Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 «_ DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5200 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 70.18 V/m; Power Drift =—0.03 dB Peak SAR (extrapolated) = 29.8 W/kg SAR(1 g) = 8.05 W/kg; SAR(10 g) = 2.30 W/kg Maximum value of SAR (measured) = 18.4 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5300 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 69.70 V/m; Power Drift = —0.01 dB Peak SAR (extrapolated) = 30.5 W/kg SAR(1 g) = 8.38 W/kg; SAR(10 g) = 2.4 W/kg Maximum value of SAR (measured) = 19.4 W/kg Dipole Calibration for Head Tissue/Pin=100mW, dist=10mm, £=5500 MHz/Zoom Scan, dist=1.4mm (8x8x7)/Cube 0: Measurementgrid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 68.97 V/m; Power Drift = —0.02 dB Peak SAR (extrapolated) = 33.3 W/kg SAR(1 g) = 8.48 W/kg; SAR(10 g) = 2.41 W/kg Maximum value of SAR (measured) = 20.2 W/kg Certificate No: D5GHzV2—1060_Jul17 Page 11 of 16


Document Created: 2018-05-15 15:40:04
Document Modified: 2018-05-15 15:40:04
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC