I18Z60073-IOT06_FCC Report_DFS-Rev0

FCC ID: 2ACCJN026

Test Report

Download: PDF
FCCID_3856289

                                   FCC PART 15
                                  TEST REPORT
                              No. I18Z60073-IOT06
                                                       for

                                    TCL Communication Ltd.

 GSM Quad-band/HSPA-UMTS Six-band/ LTE 19-band mobile phone

                                                     With

                                                 BBF100-1

                                        FCC ID: 2ACCJN026

                                        Hardware Version:09

                                    Software Version: AAX573

                                     Issued Date: 2018-05-09




Note:
The test results in this test report relate only to the devices specified in this report. This report shall not be
reproduced except in full without the written approval of CTTL.
The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST,
or any agency of the U.S.Government.
Test Laboratory:
CTTL, Telecommunication Technology Labs, CAICT
No. 52, Huayuan North Road, Haidian District, Beijing, P. R. China 100191.
Tel:+86(0)10-62304633-2512, Fax:+86(0)10-62304633-2504
Email: cttl_terminals@caict.ac.cn, website: www.caict.ac.cn


                                           No. .I18Z60073-IOT06
                                                    Page2 of 16


REPORT HISTORY
Report Number     Revision   Description       Issue Date
I18Z60073-IOT06   Rev.0      1st edition       2018-05-09


                                                                                                            No. .I18Z60073-IOT06
                                                                                                                     Page3 of 16


CONTENTS
CONTENTS .................................................................................................................................................. 3

1.             TEST LATORATORY .................................................................................................................. 4

1.1.           TESTING LOCATION ................................................................................................................ 4

1.2.           TESTING ENVIRONMENT ....................................................................................................... 4

1.3.           PROJECT DATA .......................................................................................................................... 4

1.4.           SIGNATURE ................................................................................................................................. 4

2.             CLIENT INFORMATION ........................................................................................................... 5

2.1.           APPLICANT INFORMATION ................................................................................................... 5

2.2.           MANUFACTURER INFORMATION ......................................................................................... 5

3.             EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT(AE) ...................... 6

3.1.           ABOUT EUT ................................................................................................................................. 6

3.2.           INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST ................................ 6

3.3.           GENERAL DESCRIPTION ........................................................................................................ 6

4.             REFERENCE DOCUMENTS ..................................................................................................... 6

4.1.           DOCUMENTS SUPPLIED BY APPLICANT............................................................................ 6

4.2.           REFERENCE DOCUMENTS FOR TESTING ......................................................................... 6

5.             LABORATORY ENVIRONMENT ............................................................................................. 7

6.             SUMMARY OF TEST RESULTS ............................................................................................... 7

6.1.           SUMMARY OF TEST RESULTS ............................................................................................... 7

6.2.           STATEMENTS .............................................................................................................................. 7

7.             TEST EQUIPMENTS UTILIZED .............................................................................................. 8

ANNEX A: MEASUREMENT RESULTS.................................................................................................. 9

     A.1. MEASUREMENT METHOD .................................................................................................................... 9
     A.2. CHANNEL MOVE TIME AND CHANNEL CLOSING TRANSMISSION TIME .................................................11
     A.3.NON-OCCUPANCY PERIOD .................................................................................................................. 14
     A3.1 ASSOCIATED TEST ............................................................................................................................. 14

ANNEX B: PHOTOGRAPHS OF THE TEST SET-UP .......................................................................... 15

ANNEX C: ACCREDITATION CERTIFICATE .................................................................................... 16


                                                               No. .I18Z60073-IOT06
                                                                        Page4 of 16



1. TEST LATORATORY
1.1. Testing Location
Location 1:CTTL(huayuan North Road)
  Address:               No. 52, Huayuan North Road, Haidian District, Beijing,
                         P. R. China100191



1.2. Testing Environment
  Normal Temperature:      15-35℃
  Extreme Temperature:     -10/+55℃
  Relative Humidity:       20-75%


1.3. Project data
  Testing Start Date:      2018-04-08
  Testing End Date:        2018-05-04


1.4. Signature




               Jiang Xue
     ( Prepared this test report )




              Zheng Wei
    (Reviewed this test report)




            Lv Songdong
    (Approved this test report)


                                                        No. .I18Z60073-IOT06
                                                                 Page5 of 16


2. CLIENT INFORMATION
2.1. Applicant Information
 Company Name:       TCL Communication Ltd.
                     7/F, Block F4, TCL International E City, Zhong Shan Yuan Road,
 Address:            Nanshan District, Shenzhen, Guangdong, P.R. China 518052
                     Shenzhen, Guangdong
 City:               Shenzhen
 Postal Code:        518052
 Country:            China
 Telephone:          0086-755-36611722
 Fax:                0086-75536612000-81722


2.2. Manufacturer Information
 Company Name:       TCL Communication Ltd.
                     7/F, Block F4, TCL International E City, Zhong Shan Yuan Road,
 Address:            Nanshan District, Shenzhen, Guangdong, P.R. China 518052
                     Shenzhen, Guangdong
 City:               Shenzhen
 Postal Code:        518052
 Country:            China
 Telephone:          0086-755-36611722
 Fax:                0086-75536612000-81722


                                                                      No. .I18Z60073-IOT06
                                                                               Page6 of 16


3. EQUIPMENT                 UNDER           TEST          (EUT)        AND        ANCILLARY

    EQUIPMENT(AE)
3.1. About EUT
  Description                        GSM Quad-band/HSPA-UMTS Six-band/ LTE 19-band mobile
                                     phone
  Model name                         BBF100-1
  FCC ID                             2ACCJN026
  WLAN Frequency Range               ISM Band:
                                        -5250MHz~5350MHz
                                        -5470MHz~5725MHz
  Type of modulation                 OFDM
  Antenna                            Integral Antenna
  Extreme vol. Limits                3.85V DC by Battery
  Device Type (DFS)                  Client without radar detection(only support client mode)
  TPC mechanism                      Not support
3.2. Internal Identification of EUT used during the test

EUT ID*    SN or IMEI                   HW Version             SW Version
EUT1       /                            09                     AAX573


*EUT ID: is used to identify the test sample in the lab internally.
3.3. General Description
The Equipment Under Test (EUT) is a model of GSM Quad-band/HSPA-UMTS Six-band/ LTE
19-band mobile phone with integrated antenna. It consists of normal options: lithium battery,
charger. Manual and specifications of the EUT were provided to fulfil the test.


4. REFERENCE DOCUMENTS
4.1. Documents supplied by applicant
EUT feature information is supplied by the applicant or manufacturer, which is the basis of testing.
4.2. Reference Documents for testing
The following documents listed in this section are referred for testing.

                          FCC CFR 47, Part 15, Subpart C:
                          15.205 Restricted bands of operation;
  FCC Part15              15.209 Radiated emission limits, general requirements;          2016
                          15.247 Operation within the bands 902–928MHz,
                          2400–2483.5 MHz, and 5725–5850 MHz.
                          Revision of Parts 2 and 15 of the Commission’s Rules to
  FCC 06-96               Permit Unlicensed National Information Infrastructure           2006
                          (U-NII) devices in the 5 GHz band


                                                                    No. .I18Z60073-IOT06
                                                                             Page7 of 16


5. LABORATORY ENVIRONMENT
Measurement is performed in shielding room.

6. SUMMARY OF TEST RESULTS
6.1. Summary of Test Results
                                                       Sub-clause of
    SUMMARY OF MEASUREMENT RESULTS                                                Verdict
                                                         Part15E
Channel move time         and   channel    closing
                                                       15.407 (h)(2)(iii)              P
transmission time
Non-Occupancy Period                                  15.407 (h)(2) (iv)               P
Please refer to ANNEX A for detail.
Terms used in Verdict column
P                   Pass, The EUT complies with the essential requirements in the standard.
NM                  Not measured, The test was not measured by CTTL
NA                  Not Applicable, The test was not applicable
F                   Fail, The EUT does not comply with the essential requirements in the
                    standard
6.2. Statements
CTTL has evaluated the test cases requested by the client/manufacturer as listed in section 6.1 of
this report for the EUT specified in section 3 according to the standards or reference documents
listed in section 4.1.
This report only deal with the UNII DFS functions among the features described in section 3, and
The EUT met all requirements of the reference documents.
The end user is not available to get and modify the parameters of the detected Radar Waveforms
in this product.
This model is a variant product which model name is BBF100-2,;all the test result has been
derived from test report of BBF100-2.
Test Conditions
T nom               Normal Temperature
T min               Low Temperature
T max               High Temperature
V nom               Normal Voltage
V min               Low Voltage
V max               High Voltage
H nom               Norm Humidity
A nom               Norm Air Pressure
For this report, all the test case listed above is tested under Normal Temperature and Normal
Voltage, and also under norm humidity, the specific conditions as following:
Temperature                       T nom                            26℃
Voltage                           V nom                            3.85V(By battery)
Humidity                          H nom                            44%
Air Pressure                      A nom                            1010hPa


                                                         No. .I18Z60073-IOT06
                                                                  Page8 of 16




7. TEST EQUIPMENTS UTILIZED
Conducted test system
                                     Serial                  Calibration   Calibration
No.      Equipment         Model              Manufacturer
                                    Number                      Date        Due Date
      Vector     Signal                       Rohde      &
1                         FSQ40     200089                   2017-06-02    2018-06-01
      Analyzer                                Schwarz
      Vector     Signal                       Rohde      &
2                         SMU200A   103752                   2017-06-02    2018-06-01
      General                                 Schwarz
3     Shielding Room      S81          /      ETS-Lindgren        /             /


                                                                    No. .I18Z60073-IOT06
                                                                             Page9 of 16


ANNEX A: MEASUREMENT RESULTS
A.1. Measurement Method
A.1.1. Conducted Measurements
The below figure shows the DFS setup, where the EUT is a RLAN device operating in slave mode,
without Radar Interference Detection function. This setup also contains a device operating in
master mode. The radar test signals are injected into the master device. The EUT (slave device) is
associated with the master device. WLAN traffic is generated by streaming the mpeg file from the
master to the slave in full monitor video mode using the media player.




Note:
   1) All Measurements are performed with the EUT’s narrowest channel bandwidth.
   2) The master device information is as follows
        Vendor: Cisco
        Model: AIR-AP1252AG-A-K9
        FCC ID: LDK102061, 1DK102062
   3) The software of radar signal generator (R&S SMU200A) is completely designed based on
        FCC-06-96A1/NTIA requirement.


A.1.2. Parameters of DFS test signal
1). Interference threshold values, master or client incorporation in service monitoring. For device
power less than 23dBm (E.I.R.P.), the threshold level is -62 dBm at the antenna port after
correction for antenna gain and procedural adjustments.
Because of conducted measurement performed, the calibration power from radar signal generator
to antenna port of DFS test equipment is -62 dBm.
          Maximum Transmit Power                                       Value
                  > 200 mW                                            -64 dBm
                  < 200 mW                                            -62 dBm


                                                               No. .I18Z60073-IOT06
                                                                       Page10 of 16

2). DFS requirement values
The required values are as the following table.
                  Parameter                                       Value
                Non-occupancy                                    > 1800 s
       Channel Availability Check Time                             60 s
              Channel Move Time                                    10 s
     Channel Closing Transmission Time                       200 ms + 60 ms
                                                          Minimum 80% of the 99%
          U-NII Detection Bandwidth
                                                       transmission power bandwidth


As the EUT is IP based system, the MPEG video file from NTIA website is used to steam to EUT
via the Master device.

A.1.3. Measurement Uncertainty
                   Item                            Measurement Uncertainty
                   Time                                     0.70 ms
                  Power                                    0.75 dBm


                                                                                                      No. .I18Z60073-IOT06
                                                                                                              Page11 of 16

A.2. Channel move time and channel closing transmission time
Measurement Limit:
                Test Items                                                                      Limit
channel closing transmission time                                                     < 200 ms + 60 ms
Channel move time                                                                              < 10 s

Measurement Results:

Frequency Band: 5250MHz ~ 5350MHz

                                                                      RBW   3 MHz    Delta 2 [T1 ]
                                                                      VBW   10 MHz             -38.79 dB
                        Ref    -10 dBm              Att   15 dB       SWT   12 s            10.000000 s

                        -10                                                          Marker 1 [T1 ]
                                                                                               -22.23 dBm
                               1                                                           750.000000 ms     A
                        -20
                                                                                                            SGL
                1 AP
                CLRWR
                        -30




                        -40




                        -50


                                                                                                 2
                        -60


                                                                                                            3DB
                        -70




                        -80




                        -90




                        -100



                        -110

                        Center 5.28 GHz                           1.2 s/




               Date: 2.MAY.2018          15:18:53



The channel move time is as the figure. It shows the time of the radar and the client pulses. The
figure shows that the client stops transmission within 10 seconds, and no transmissions occur
after 10 seconds later of the radar burst signal.
Frequency Band: 5250MHz ~ 5350MHz


                                                                                                        No. .I18Z60073-IOT06
                                                                                                                Page12 of 16

                                                                       RBW    3 MHz    Delta 4 [T1 ]
                                                                      * VBW   10 MHz             -39.71 dB
                        Ref    -14 dBm              Att   15 dB        SWT    3 s            822.115385 ms

                                                                                       Marker 1 [T1 ]
                                         1                                                       -21.75 dBm
                        -20
                                                                                             485.576923 ms     A
                                                                                       Delta 2 [T1 ]          SGL
                1 AP    -30                                                                      -39.36 dB
                CLRWR
                                                                                               4.807692 ms
                                                                                       Delta 3 [T1 ]
                        -40                                                                      -40.00 dB
                                                                                             812.500000 ms

                        -50



                                         2                   34
                        -60




                        -70                                                                                   3DB




                        -80




                        -90




                        -100




                        -110


                        Center 5.26 GHz                           300 ms/




                Date: 5.MAY.2018         16:18:03



The closing transmission time is as the figure, and the result is 254.81ms.

Conclusion: PASS



Frequency Band 5470MHz ~ 5725MHz

                                                                       RBW    3 MHz    Delta 2 [T1 ]
                                                                       VBW    10 MHz             -27.19 dB
                        Ref    -14 dBm              Att   15 dB        SWT    12 s            10.000000 s

                                                                                       Marker 1 [T1 ]

                        -20                                                                      -33.39 dBm
                                                                                             769.230769 ms     A
                                                                                                              SGL
                1 AP    -30    1
                CLRWR


                        -40




                        -50


                                                                                                   2
                        -60




                        -70                                                                                   3DB




                        -80




                        -90




                        -100




                        -110


                        Center 5.61 GHz                           1.2 s/




                Date: 2.MAY.2018         15:29:11



The channel move time is as the figure. It shows the time of the radar and the client pulses. The
figure shows that the client stops transmission within 10 seconds, and no transmissions occur
after 10 seconds later of the radar burst signal.


                                                                                                        No. .I18Z60073-IOT06
                                                                                                                Page13 of 16

Frequency Band 5470MHz ~ 5725MHz
                                                                       RBW    3 MHz    Delta 4 [T1 ]
                                                                      * VBW   10 MHz             -45.41 dB
                        Ref    -15 dBm              Att   10 dB        SWT    3 s            687.500000 ms

                                                                                       Marker 1 [T1 ]
                                   1
                        -20                                                                      -21.77 dBm
                                                                                             346.153846 ms     A
                                                                                       Delta 2 [T1 ]          SGL
                1 AP    -30                                                                      -45.26 dB
                CLRWR
                                                                                             120.192308 ms
                                                                                       Delta 3 [T1 ]
                        -40
                                                                                                 -45.60 dB
                                                                                             677.884615 ms

                        -50




                        -60
                                         2           34

                        -70
                                                                                                              3DB



                        -80




                        -90




                        -100




                        -110


                        Center 5.69 GHz                           300 ms/




               Date: 4.MAY.2018          18:03:38



The closing transmission time is as the figure, and the result is 177.88ms

Conclusion: PASS


                                                                                                          No. .I18Z60073-IOT06
                                                                                                                  Page14 of 16

A.3.Non-Occupancy Period
Measurement Limit:
                 Test Items                                                                      Limit
Non-Occupancy Period                                                                             > 1800 s

A3.1 Associated test

Associate the master and client, transmit specified stream between the master and client; monitor
the analyzer on the operating frequency to make sure no beacons have been transmitted for 1800
seconds.

Frequency Band: 5150MHz ~ 5350MHz

                                                                       RBW   3 MHz    Delta 2 [T1 ]
                                                                       VBW   10 MHz             -38.11 dB
                         Ref    -14 dBm              Att   15 dB       SWT   2000 s           1.800000 ks

                                                                                      Marker 1 [T1 ]
                         1                                                                      -21.69 dBm
                         -20
                                                                                             20.000000 s      A
                                                                                                             SGL
                 1 AP    -30
                 CLRWR


                         -40




                         -50


                                                                                                      2
                         -60




                         -70                                                                                 3DB




                         -80




                         -90




                         -100




                         -110


                         Center 5.32 GHz                           200 s/




                Date: 2.MAY.2018          16:12:23



The figure above shows that the client does not transmit any emission within 1800 seconds after
getting the order of “stop transmits” from the DFS master (access point).

Conclusion: PASS


                                    No. .I18Z60073-IOT06
                                            Page15 of 16


ANNEX B: PHOTOGRAPHS OF THE TEST SET-UP


Layout of Conducted Test


                                                   No. .I18Z60073-IOT06
                                                           Page16 of 16


ANNEX C: Accreditation Certificate




                      *** END OF REPORT BODY ***



Document Created: 2018-05-09 10:16:19
Document Modified: 2018-05-09 10:16:19

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC