I17Z62134-SEM01_SAR_Rev0_6

FCC ID: 2ACCJN023

RF Exposure Info

Download: PDF
FCCID_3695223

) S <| Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.10.0 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2450 MHz # 1 MHz Head TSL barameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 37.8 x6 % 1.87 mho/m £ 6 % Head TSL temperature change during test «05 °C «+ SAR result with Head TSL SAR averaged over 1 cm‘ (1 g) of Head TSL Condition SAR measured 250 mW input power 13.4 Wi/kg SAR for nominal Head TSL parameters normalized to 1W 52.2 Wikg a 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 6.26 Wikg SAR for nominal Head TSL parameters normalized to 1W 24.7 Wikg 2 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.7 1.95 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 521 26 % 2.04 mho/m + 6 % Body TSL temperature change during test <0.5 °C —— ———— SAR result with Body TSL SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 250 mW input power 12.9 Wi/kg SAR for nominal Body TSL parameters normalized to 1W 50.4 Wikg x 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 250 mW input power 6.03 W/kg SAR for nominal Body TSL parameters normalized to 1W 23.8 Wikg + 16.5 % (k=2) Certificate No: D2450V2—853_Jul17 Page 3 of 8

yA (3 N Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 52.0 Q + 5.0 jQ Return Loss ~25.6 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 49.6 Q + 6.3 jQ Return Loss —24.0 dB General Antenna Parameters and Design IEectrical Delay (one direction) T 1.161 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On someof the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on November 10, 2009 Certificate No: D2450V2—853_Jul17 Page 4 of 8

DASY5 Validation Report for Head TSL Date: 20.07.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 853 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 1.87 $/m; s = 37.8; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvF(8.12, 8.12, 8.12); Calibrated: 31.05.2017; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 28.03.2017 * Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 «_ DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 112.7 V/m; Power Drift = —0.00 dB Peak SAR (extrapolated) = 27.0 W/kg SAR(1 g) = 13.4 W/kg; SAR(10 g) = 6.26 W/kg Maximum value of SAR (measured) = 21.5 W/kg dB 0 —4.00 —8.00 —12.00 —16.00 —20.00 0 dB = 21.5 W/kg = 13.32 dBW/kg Certificate No: D2450V2—853_Jul17 Page 5 of 8

mm TL Impedance Measurement Plot for Head TSL 20 Jul 2017 11:54:15 CHI) sii 1 U FS 41 51.965 a 4.99570 a 322.01 pH 2 450.000 000 MHz fAvg 16 H1d CH2 Ca Av 159 H1d START 2 250.000 000 MHz STOP 2 650.000 000 MHz Certificate No: D2450V2—853_Jul17 Page 6 of 8

DASY5 Validation Report for Body TSL Date: 21.07.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 853 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 2.04 $/m; & = 52.1; p = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN7349; ConvF(8.1, 8.1, 8.1); Calibrated: 31.05.2017; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn601; Calibrated: 28.03.2017 * Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 * DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 104.1 V/m; Power Drift = —0.09 dB Peak SAR (extrapolated) = 25.5 W/kg SAR(I g) = 12.9 W/kg; SAR(10 g) = 6.03 W/kg Maximum value of SAR (measured) = 20.0 W/kg dB 0 —5.00 —10.00 —15.00 —20.00 —25.00 0 dB = 20.0 W/kg = 13.01 dBW/kg Certificate No: D2450V2—853_Jul17 Page 7 of 8

mm TL Impedance Measurement Plot for Body TSL 21 Jul 2017 14:42:34 1 U FS 11 49.619 a 6.2656 a 407.02 pH 2450.000 000 MHz Av 16 * H1d CH2 Ca Av 169 H1d START 2 250.000 000 MHz STOP 2 650.000 000 MHz Certificate No: D2450V2—853_Jul17 Page 8 of 8

No.I17Z62134-SEM01 Page 169 of 169 ANNEX I Accreditation Certificate ©Copyright. All rights reserved by CTTL.


Document Created: 2017-12-25 13:30:14
Document Modified: 2017-12-25 13:30:14
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC