I18Z61178-SEM01_SAR_Rev0 - 0816_3

FCC ID: 2ACCJH093

RF Exposure Info

Download: PDF
FCCID_4041391

) Y C T C t mt tt uo Callbratlon Laboratory Of ¢\“\‘wl"’/,, s Schweizerischer Kalibrierdienst Schmid & Partner M C Service suisse d‘étalonnage Engineering AG pepemitinl Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland é,fi\\? S Swiss Calibration Service Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid NORMx,y,z sensitivity in free space ConvF sensitivity in TSL / NORMx,y,z DCP diode compression point CF crest factor (1/duty_cycle) of the RF signal A, B, C, D modulation dependent linearization parameters Polarization o (p rotation around probe axis Polarization 8 8 rotation around an axis thatis in the plane normal to probe axis (at measurement center), i.e., 8 = 0 is normal to probe axis Connector Angle information used in DASY system to align probe sensor X to the robot coordinate system Calibration is Performed According to the Following Standards: IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 IEC 62209—1, ", "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand— held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Methods Applied and Interpretation of Parameters: NORMx,y,z: Assessed for E—field polarization 8 = 0 (f < 900 MHz in TEM—cell; f > 1800 MHz: R22 waveguide). NORMx,y,z are only intermediate values, i.e., the uncertainties of NORMx,y,z does not affect the E*—field uncertainty inside TSL (see below ConvF). NORM(Mx,y,z = NORMx,y,z * frequency_response (see Frequency Response Chart). This linearization is implemented in DASY4 software versions later than 4.2. The uncertainty of the frequency response is included in the stated uncertainty of ConvF. DCPx,y,z: DCP are numerical linearization parameters assessed based on the data of power sweep with CW signal (no uncertainty required). DCP does not depend on frequency nor media. PAR: PAR is the Peak to Average Ratio that is not calibrated but determined based on the signal characteristics Axy.z; Bxy.z; Cxy.z; Dx,y,z; VRx,y,z: A, B, C, D are numerical linearization parameters assessed based on the data of power sweep for specific modulation signal. The parameters do not depend on frequency nor media. VR is the maximum calibration range expressed in RMS voltage across the diode. ConvF and Boundary Effect Parameters: Assessed in flat phantom using E—field (or Temperature Transfer Standard for f < 800 MHz) and inside waveguide using analytical field distributions based on power measurements for f > 800 MHz. The same setups are used for assessment of the parameters applied for boundary compensation (alpha, depth) of which typical uncertainty values are given. These parameters are used in DASY4 software to improve probe accuracy close to the boundary. The sensitivity in TSL corresponds to NORMx,y,z * ConvF whereby the uncertainty corresponds to that given for ConvF. A frequency dependent ConvF is used in DASY version 4.4 and higher which allows extending the validity from + 50 MHz to + 100 MHz. Spherical isotropy (3D deviation from isotropy): in a field of low gradients realized using a flat phantom exposed by a patch antenna. Sensor Offset: The sensor offset corresponds to the offset of virtual measurement center from the probe tip (on probe axis). No tolerance required. Connector Angle: The angle is assessed using the information gained by determining the NORMx (no uncertainty required). Certificate No: EX3—7464_Sep17 Page 2 of 38 wervopg n ree a io rgn rewr a vewruer e tona wmz d e ae.

(Ilé"") EX3DV4 —— SN:7464 September 12, 2017 Probe EX3DV4 SN:7464 Manufactured: September 6, 2016 Calibrated: September 12, 2017 Calibrated for DASY/EASY Systems (Note: non—compatible with DASY2 system!) Certificate No: EX3—7464_Sep17 Page 3 of 38 wervoprg n ree a io rgr e a vewruer e una wy nz

o — — — EX3DV4— SN:7464 September 12, 2017 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7464 Basic Calibration Parameters Sensor X Sensor Y Sensor Z Unc (k=2) Norm (uV/(V/m)")* 0.45 0.43 0.45 £10.1 % DCP (mV)" 101.6 99.3 99.7 Modulation Calibration Parameters UID Communication System Name A B c D VR Unc® dB dByuy dB mV (k=2) 0 CW x 0.0 0.0 1.0 0.00 150.5 23.3 % Y 0.0 0.0 1.0 144.7 2 0.0 0.0 1.0 147.0 Note: For details on UID parameters see Appendix. Sensor Model Parameters C1 C2 a T1 T2 Ts T4 T5 T6 IF fF V ms.V~* ms.V~* ms VA V 57.86 441.1 37.02 12.02 0.826 5.039 0.00 0.727 1.006 NI—<[x 59.82 453.4 36.65 14.84 0.468 5.100 0.25 0.626 1.007 65.01 497.8 37.35 15.97 1.043 5.073 0.00 0.801 1.008 The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. * The uncertainties of Norm X,Y,Z do not affect the E*—field uncertainty inside TSL (see Pages 5 and 6). ° Numerical linearization parameter: uncertainty not required. © Uncertainty is determined using the max. deviation from linear response applying rectangular distribution and is expressed for the square of the field value. Certificate No: EX3—7464_Sep17 Page 4 of 38 w io voperg n ragh bwe e wrn ragevnr n nenener n en meg n c n

m_" _ —— ‘/"/"/, ~o — 20 2 EX3DV4— SN:7464 September 12, 2017 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7464 Calibration Parameter Determined in Head Tissue Simulating Media Relative Conductivity Depth ® Unce f(MHz)© Permittivity" (S/m)® ConvFX ConvFY ConvFZ Alpha® |__(mm) (k=2) 150 52.3 0.76 12.20 12.20 12.20 0.00 1.00 #13.3 % 300 45.3 0.87 11.77 AT 117z 0.09 1.20 +13.3 % 450 43.5 0.87 1117 1147 | 1147 0.15 1.20 * 13.3 % 750 41.9 0.89 10.57 10.57 10.57 0.53 0.80 +12.0 % 835 41.5 0.90 10.28 10.28 10.28 0.48 0.80 +12.0 % 900 41.5 0.97 10.03 10.03 10.03 0.28 1.09 +12.0 % 1450 40.5 1.20 9.05 9.05 9.05 0.37 0.80 *12.0 % 1640 40.2 1.31 8.82 8.82 8.82 0.35 0.80 #12.0 % 1750 40.1 1.37 8.70 8.70 8.70 0.38 0.80 * 12.0 % 1810 40.0 140 8.42 8.42 8.42 0.32 0.85 £12.0 % 1900 40.0 1.40 8.39 8.39 8.39 0.35 0.80 +12.0 % 2000 40.0 1.40 8.39 8.39 8.39 0.32 0.89 +*12.0 % 2100 39.8 1.49 8.54 8.54 8.54 0.27 0.86 +12.0 % 2300 39.5 1.67 8.40 8.40 8.40 0.34 0.95 £12.0% 2450 39.2 1.80 7.89 7.89 7.89 0.34 0.93 *12.0 % 2600 39.0 1.96 7.76 7.176 7.76 0.37 0.92 £12.0 % 3500 37.9 2.91 7.40 7.40 7.40 0.41 0.94 £13.1 % 3700 37.7 3.12 711 711 711 0.50 0.84 £13.1% 5200 36.0 4.66 5.82 5.82 5.82 0.35 1.80 #13.1% 5250 35.9 4.71 5.68 5.68 5.68 0.35 1.80 £13.1 % 5300 35.9 4.76 5.53 5.53 5.53 0.35 1.80 £13.1 % 5500 35.6 4.96 5.21 5.21 5.21 0.40 1.80 £13.1% 5600 35.5 5.07 4.98 4.98 |‘ 4.98 0.40 1.80 *13.1% 5750 35.4 5.22 5.04 5.04 5.04 0.40 1.80 #13.1% 5800 85.3 5.27 5A1 5141 5.11 0.40 1.80 #13.1 % © Frequency valldity above 300 MHz of 100 MHz anly applies for DASY v4.4 and higher (see Page 2), else it is restricted to + 50 MHz. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band. Frequency validity below 300 MHz is # 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Above 5 GHz frequency validity can be extended to + 110 MHz. " Atfrequencies below 3 GHz, the validity of tissue parameters (s and a) can be relaxed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tssue parameters (s and ) is restricted to + 5%. The uncertainty is the RSS of the ConvF uncertainty for indicated target tissue arameters. 8 Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below + 2% for frequencies between 3—6 GHz at any distance larger than half the probe tip diamater from the boundary. Certificate No: EX3—7464_Sep17 Page 5 of 38 snn vrperg n rag bee e aror ngn nvar n nenever e menr meg n +s

ty — EX3DV4— SN:7464 September 12, 2017 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7464 Calibration Parameter Determined in Body Tissue Simulating Media Relative Conductivity Depth ° Unc f(MHz)* Permittivity" (S/m)" ConvFX ConvF¥Y ConvFEZ Aipha® _({mm) (k=2) 150 61.9 0.80 12.19 12.19 12.19 0.00 1.00 £13.3% 300 58.2 0.92 1182 11.32 11.32 0.06 1.20 13.3 % 450 56.7 0.94 11.05 11.05 11.05 0.09 1.20 13.3 % 750 55.5 0.96 10.63 10.63 10.63 0.49 0.88 +12.0 % 835 55.2 0.97 10.21 10.21 10.21 0.45 0.80 +12.0 % 900 55.0 1.05 10.17 10.17 10.17 0.42 0.80 £12.0 % 1450 54.0 1.30 9.18 9.18 9.18 0.36 0.80 £12.0 % 1640 53.7 142 9.12 9.12 9.12 0.38 0.80 +# 12.0 % 1750 53.4 149 8.60 8.60 8.60 0.44 0.80 + 12.0 % 1810 53.3 1.52 8.45 8.45 8.45 0.41 0.80 *12.0 % 1900 53.3 1.52 8.32 8.32 8.32 0.42 0.80 +12.0 % 2000 53.3 1.52 8.24 8.24 8.24 0.39 0.80 +120 % 2100 53.2 1.62 8.38 8.38 8.38 0.40 0.80 +12.0 % 2300 52.9 1.81 8.30 8.30 8.30 0.42 0.93 +12.0 % 2450 52.7 1.95 8.09 8.09 8.09 0.34 0.95 #12.0 % 2600 52.5 216 7.84 7.84 7.84 0.30 0.97 +12.0 % 3500 51.3 3.31 7.06 7.06 7.06 0.68 0.70 #13.1% 3700 51.0 3.55 6.99 6.99 6.99 0.85 0.60 #13.1% 5200 49.0 5.30 5.39 5.39 5.39 0.35 1.90 £13.1 % 5250 48.9 5.36 5.29 5.29 5.29 0.35 1.90 £13.1% 5300 48.9 5.42 5.19 5.19 5.19 0.35 1.90 £18.1 % 5500 48.6 5.65 4.61 4.61 4.61 0.40 1.90 #13.1 % 5600 48.5 5.77 4.50 4.50 4.50 0.40 1.90 £18.1% 5750 48.3 5.94 4.59 4.59 4.59 0.40 1.90 *13.1 % 5800 48.2 6.00 4.67 4.67 4.67 0.40 1.90 £13.1 % © Frequency validity above 300 MHz of £ 100 MHz only applies for DASY v4.4 and higher (see Page 2), else it is restricted to + 50 MHz. The uncertainty is the RSS of the ConvF uncertainty at calibration frequency and the uncertainty for the indicated frequency band, Frequency validity below 300 MHz is + 10, 25, 40, 50 and 70 MHz for ConvF assessments at 30, 64, 128, 150 and 220 MHz respectively. Above 5 GHz frequency validity can be extended to + 110 MHz. " At frequencies below 3 GHz, the validity of tissue parameters (c and a) can be relaxed to + 10% if liquid compensation formula is applied to measured SAR values. At frequencies above 3 GHz, the validity of tissue parameters (e and o) is restricted to + 5%. The uncertainty is the RSS of the Convr uncertainty for indicated target fissue garametersA Alpha/Depth are determined during calibration. SPEAG warrants that the remaining deviation due to the boundary effect after compensation is always less than + 1% for frequencies below 3 GHz and below +2% for frequencies between 3—6 GHz at any distance larger than half the probe tip diameter from the boundary. Certificate No: EX3—7464_Sep17 Page 6 of 38 w n vperg n ragi ie e n rever e nenener e new weg n ce

EX3DV4— SN:7464 September 12, 2017 Frequency Response of E—Field (TEM—Cell:ifi110 EXX, Waveguide: R22) 1.5 TATTTTT 4A ofeccvcnnnnmmmmnmnnnnnd 13—: """"""""""":' """"" £ | Frequency response (normalized) 1.2_5 ....................................... LT omm enemeaprmmmnmemenny Tod Uncertainty of Frequency Response of E—field: £ 6.3% (k=2) Certificate No: EX3—7464_Sep17 Page 7 of 38 wr n vpey n rage bee nb n rgn rewr in cevever n nevr weg n +s

) @7"7‘/ ~3g— =‘/ EX3DV4— SN:7464 September 12, 2017 Receiving Pattern (¢), 9 = 0° f=600 MHz,TEM f=1800 MHz,R22 . so 90 135 © 45 135 * * 45 + s._ * x—*~—. + " t + ; | — + & * }+* & + v ts 2s se I & ~} + + $ 34 4 ; 180 + f # 0 120 + P % * o« og o8 7 o4 o4 og os + f + + $ , /4 ¥9S_ . i + * . x 1 + ho OA + . : } & | & + R " > + 226 ¥any.— it ms 228 * * s1s 0 "2ro # e & NCB « e e (e_ Tot X Y £ Tot X Y Z Error [dB] —0.57 3 0 0 Roll [*] 600 MHz Uncertainty of Axial Isotropy Assessment: £ 0.5% (k=2) Certificate No: EX3—7464_Sep17 Page 8 of 38 wervopg n ree a io rgn rewr a vewruer e tona wmz d e ae.

) J _ cy EX3DV4— SN:7464 September 12, 2017 Dynamic Range f(SARneaq) (TEM cell , fevai= 1900 MHz) Input Signal [uV) 102 102 101 10 101 10 103 SAR [mW/cm3] not compensated compensated 2 1 @ L g 0 * 4+ u n i 2f f b dihen — ’\\ 2 it Dt N : ; iR 103 102 101 100 101 102 103 SAR [mW/cm3] 2e] not compensated compensated Uncertainty of Linearity Assessment: £ 0.6% (k=2) Certificate No: EX3—7464_Sep17 Page 9 of 38 w in voperg n ragi en n ern bage en e nene en n ne n n n n n >

EX3DV4— SN:7464 September 12, 2017 Conversion Factor Assessment f= 900 MHz,WGLS R9 (H_convF) f= 1810 MHz,WGLS R22 (H_convF) «0 | :’ + 30 | as! & t * 5| 307 * E *\ [ & rs! & :o‘ & $ | 5 20| {% 15%’ & | a | 15 10 10| | f + s| 05 I — oo ‘ Di : i «_ a 0 5 10 1 20 3 5 Lo 0 10 1 20 30 3 «o z {mm} : {mm] _eJ _*J e Ce] anabtcal measured anaiyncal measired Deviation from Isotropy in Liquid Error (¢, 3), f = 900 MHz 5 8 $ & &. —1.0 —0.8 —0.6 —0.4 —0.2 0.0 02 0.4 0.6 08 1.0 Uncertainty of Spherical Isotropy Assessment: £ 2.6% (k=2) Certificate No: EX3—7464_Sep17 Page 10 of 38 wervopg n ree a io rgn rewr a vewruer e tona wmz d e ae.

us n s n n> EX3DV4— SN:7464 September 12, 2017 DASY/EASY — Parameters of Probe: EX3DV4 — SN:7464 Other Probe Parameters Sensor Arrangement Triangular Connector Angle (°) 27.6 Mechanical Surface Detection Mode enabled Optical Surface Detection Mode disabled Probe Overall Length 337 mm Probe Body Diameter 10 mm Tip Length 9 mm Tip Diameter 2.5 mm Probe Tip to Sensor X Calibration Point 1 mm Probe Tip to Sensor Y Calibration Point . 1 mm Probe Tip to Sensor Z Calibration Point 1 mm Recommended Measurement Distance from Surface 14 mm Certificate No: EX3—7464_Sep17 Page 11 of 38 wervopg n ree a io rgn rewr a vewruer e tona wmz d e ae.

No. I18Z61178-SEM01 Page 162 of 221 ANNEX H Dipole Calibration Certificate 750 MHz Dipole Calibration Certificate ©Copyright. All rights reserved by CTTL.

n S (I Calibration . Laboratory of gr C/4 S Schweizerischer Kalibrierdienst Schmid & Partner ;fifi c Service suisse d‘étalonnage Engineering AG ze Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland {»/,,/fi\\\v} S Swiss Calibration Service "thil ult Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvrF sensitivity in TSL / NORM x.y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D750V3—1017_Jul17 Page 2 of 8

(S) Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version Extrapolation DASYS5 Advanced Extrapolation V52.10.0 Phantom Modular Flat Phantomn Distance Dipole Center — TSL 15 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 750 MHz &1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 41.9 0.89 mho/m Measured Head TSL parameters (22.0 £0.2) °C 41.0 £6 % 0.89 mho/m + 6 % Head TSL temperature change during test <0.5 °C ——— SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 2.09 Wikg SAR for nominal Head TSL parameters normalized to 1W 8.32 Wikg + 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 1.36 Wikg SAR for nominal Head TSL parameters normalized to 1W 5.42 Wikg + 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 55.5 0.96 mho/m Measured Body TSL parameters (22.0 + 0.2) °C 55.0 6 % 0.99 mho/m + 6 % Body TSL temperature change during test <0.5 °C ween SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 2.22 W/kg SAR for nominal Body TSL parameters normalized to 1W 8.66 Wikg a 17.0 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL condition SAR measured 250 mW input power 1.45 Wikg SAR for nominal Body TSL parameters normalized to 1W 5.68 Wikg £ 16.5 % (k=2) Certificate No: D750V3—1017_Jul17 Page 3 of 8

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 54.4 Q +0.5 jQ Return Loss —27.5 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 49.3 Q — 3.4 jQ Return Loss —29.1 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.033 ns _I After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on March 22, 2010 Certificate No: D750V3—1017_Jul17 Page 4 of 8

DASY5 Validation Report for Head TSL Date: 19.07.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 750 MHz; Type: D750V3; Serial: D750V3 — SN:1017 Communication System: UID 0 — CW; Frequency: 750 MHz Medium parameters used: £ = 750 MHz; 0 = 0.89 S/m; & =41; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: «_ Probe: EX3DV4 — SN7349; ConvF(10.49, 10.49, 10.49); Calibrated: 31.05.2017; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 28.03.2017 e Phantom: Flat Phantom 4.9 (front); Type: QD OOL P49 AA; Serial: 1001 «_ DASY532 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Head Tissue/Pin=250 mW, d=15mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 58.85 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 3.22 W/kg SAR(1 g) = 2.09 W/kg; SAR(10 g) = 1.36 W/kg Maximum value of SAR (measured) = 2.83 W/kg dB 0 —2.20 —4.40 —6.60 —8.80 —11.00 0 dB = 2.83 W/kg = 4.52 dBW/kg Certificate No: D750V3—1017_Jul17 Page 5 of 8

Illll) ( Impedance Measurement Plot for Head TSL 19 Jul 2017 ©8:47:38 CHI) sii 1 U FS 4: 54.355 a ©.5197 0 109.00 pH 750.000 000 MHz o Del Ca Av 1.EnS H1d CH2 Ca Av 16 $ H1d START 550.000 000 MHz STOP 950.000 000 MHz Certificate No: D750V3—1017_Jul17 Page 6 of 8


Document Created: 2018-10-17 16:38:40
Document Modified: 2018-10-17 16:38:40
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC