I19Z61162-SEM01_SAR_Rev1_8

FCC ID: 2ACCJH089

RF Exposure Info

Download: PDF
FCCID_4376076

ow n e se se k k Nes N n en w P s w4 uj Callbl.'atlon Laboratory of Q‘QM?Z S Schweizerischer Kalibrierdienst Schmid & Partner m c Service suisse d‘étalonnage Engineering AG s o amls Servizio svizzero di taratura ; M Zeughausstrasse 43, 8004 Zurich, Switzerland x4rosng fan & S i iFSH M Swiss Calibration Service Hlilals Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented paralle! to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. e Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. e SAR measured: SAR measured at the stated antenna input power. e SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D2600V2—1012_Jul18 Page 2 of 8

3) m ~<g > — l > — Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.10.1 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2600 MHz + 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.0 1.96 mho/m Measured Head TSL parameters (22.0 £0.2) °C 37.2 26 % 2.02 mho/m +6 % Head TSL temperature change during test <0.5 °C —— —— SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 14.2 W/ikg SAR for nominal Head TSL parameters normalized to 1W 55.4 Wikg + 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 6.33 W/kg SAR for nominal Head TSL parameters normalized to 1W 24.9 Wikg x 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. . Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.5 2.16 mho/m Measured Body TSL parameters (22.0 £0.2) °C 51.5 26 % 2.20 mho/m £ 6 % Body TSL temperature change during test <0.5 °C =— SAR result with Body TSL SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 250 mW input power 13.7 W/kg SAR for nominal Body TSL parameters normalized to 1W 54.1 Wikg #17.0 % (k=2) SAR averaged over 10 em* (10 g) of Body TSL condition SAR measured 250 mW input power 6.17 Wikg SAR for nominal Body TSL parameters normalized to 1W 24.5 Wikg # 16.5 % (k=2) Certificate No: D2600V2—1012_Jul18 Page 3 of 8

Appendix (Additional assessments outside the scope of SCS 01 08) Antenna Parameters with Head TSL Impedance, transformed to feed point 474 Q —7.4 jQ Return Loss —21.9 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 44.1 Q — 4.9 jQ Return Loss —21.8 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.154 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on October 30, 2007 Certificate No: D2600V2—1012_Jul18 Page 4 of 8

mm> De e e /7/ — t e t i n n n> DASY5 Validation Report for Head TSL Date: 26.07.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2600 MHz; Type: D2600V2; Serial: D2600V2 — SN:1012 Communication System: UID 0 — CW; Frequency: 2600 MHz Medium parameters used: f = 2600 MHz; 0 = 2.02 S/m; & = 37.2; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN7349; ConvF(7.7, 7.7, 7.7) @ 2600 MHz; Calibrated: 30.12.2017 e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 26.10.2017 e Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 * DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 118.3 V/m; Power Drift = —0.04 dB Peak SAR (extrapolated) = 28.3 W/kg SAR(1 g) = 14.2 W/kg; SAR(10 g) = 6.33 W/kg Maximum value of SAR (measured) = 23.7 W/kg dB 0 —5.20 —10.40 —15.60 —20.80 —26.00 0 dB = 23.7 W/kg = 13.75 dBW/kg Certificate No: D2600V2—1012_Jul18 Page 5 of 8

Impedance Measurement Plot for Head TSL File View Channel Sweep Calibration Trace Scale Marker System Window Help 2600000 GHz 47.371 Q 8.2358 pF —7.4326 Q \, 2600000 GHz 80.734 mU ~105.12 ° Ch1Avg= 20 Ch1: Start 2.40000 GHz Stop 2.90000 GHz —2).859 dB 35.00 00 Ch = Ch1: Start 2.40000 GHa ——— Stop 2.20000 GHz Status CH 1: en Te ira Avg=20 Delay LCL Certificate No: D2600V2—1012_Jul18 Page 6 of 8

8 DASY5 Validation Report for Body TSL Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2600 MHz; Type: D2600V2; Serial: D2600V2 — SN:1012 Date: 26.07.2018 Communication System: UID 0 — CW; Frequency: 2600 MHz Medium parameters used: f = 2600 MHz; 0 = 2.2 S/m; & = 51.5; p = 1000 kg/m3 Phantom section: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI C€63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvF(7.81, 7.81, 7.81) @ 2600 MHz; Calibrated: 30.12.2017 e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 26.10.2017 + Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 «_ DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 107.5 V/m; Power Drift = —0.07 dB Peak SAR (extrapolated) = 27.7 W/kg SAR(I g) = 13.7 W/kg; SAR(10 g) = 6.17 W/kg Maximum value of SAR (measured) = 22.6 W/kg dB 0 —5.20 ~10.40 —15.60 —20.80 —26.00 0 dB = 22.6 W/kg = 13.54 dBW/kg Certificate No: D2600V2—1012_Jul18 Page 7 of 8

(IEI) Impedance Measurement Plot for Body TSL File View Channel Sweep Calibration Trace Scale Marker System Window Help 2600000 GHz 44.132 O 12.374 pF —4.9469 C y 2600000 GHz 81.418 mU —136.86 ° Ch1Avg= 20 Ch1: Start 2.40000 GHz —— Stop 2.80000 GHz 00 —21.786 dB 00 0.00 00 Ch1 Ch1: Start 2. Stop 2.90000 GHz Status CH 1: E11 | C" 1—Port Avg=20 Delay LCL Certificate No: D2600V2—1012_Jul18 Page 8 of 8

We n ae se k ns wever im n we en uen n ow w n n n n e in s — ap “ "/A i&\\ *E“T In Collaboration with es Afi ©_ 2j ‘T];l; CALIBRATION LABORATORY CNAS Bft h \\\‘“ l,/’ /-\ CALIBRATION Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China l/"l'‘\‘\\ 1 CNAS LO570 Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 t3 E—mail: cttl@chinattl.com Hitp:/www.chinattl.on Client : CTTL Certificate No: 218—60359 CALIBRATION CERTIFICATE Object DAE4 — SN: 1525 Calibration Procedure(s) FP—241—002—01 Calibration Procedure for the Data Acquisition Electronics (DAEx) Calibration date: September 18, 2018 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(S!). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(2243)°c and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Process Calibrator 753 1971018 20—Jun—18 (CTTL, No.J18X05034) June—19 Name Function Signature Calibrated by: Yu Zongying SAR Test Engineer @.,db Reviewed by: Lin Hao SAR Test Engineer ( \f{f% $ Approved by: Qi Dianyuan SAR Project Leader y‘m Issued: September 20, 2018 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: Z18—60359 Page 1 of 3

© e® |n Collsboration with iaaaaey»" CALIERATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Hittp:/www.chinattl.cn Glossary: DAE data acquisition electronics Connector angle information used in DASY system to align probe sensor X to the robot coordinate system. Methods Applied and Interpretation of Parameters: e DC Voltage Measurement: Calibration Factor assessed for use in DASY system by comparison with a calibrated instrument traceable to national standards. The figure given corresponds to the full scale range of the voltmeter in the respective range. e Connector angle: The angle of the connector is assessed measuring the angle mechanically by a tool inserted. Uncertainty is not required. e The report provide only calibration results for DAE, it does not contain other performance test results. Certificate No: Z18—60359 Page 2 of 3

WC |n, Collaboration with =‘["]‘], a uiaaazye" CALIBRATION LABORATORY Add: No.51 Xucyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2512 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com Http://www.chinattl.en DC Voltage Measurement A/D — Converter Resolution nominal High Range: 1LSB = 6.1uV , full range = ~100... +300 mV Low Range: 1LSB = 61nV , full range = PAvcrssef +3mV DASY measurement parameters: Auto Zero Time: 3 sec; Measuring time: 3 sec Calibration Factors X Y Z High Range 405.933 + 0.15% (k=2) 405.969 + 0.15% (k=2) 405.417 + 0.15% (k=2) Low Range 3.99161+0.7% (k=2) 4.01041+0.7% (k=2) 3.99418 +0.7% (k=2) Connector Angle Connector Angle to be used in DASY system 59 @1° Certificate No: Z18—60359 Page 3 of 3

No. I19Z61162-SEM01 Page 251 of 251 ANNEX K Accreditation Certificate ©Copyright. All rights reserved by CTTL.


Document Created: 2019-07-26 15:43:37
Document Modified: 2019-07-26 15:43:37
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC