Modular approval request

FCC ID: 2AC23-WT31M2311A

Cover Letter(s)

Download: PDF
FCCID_3256989

Hui Zhou Gaoshengda Technology Co.,LTD FCC Modular Approval Request Number:CF305 Version: V05 Date: 01-12-2016 To the FCC or FCC TCB handling this application Hereby we, Company name (grantee) Hui Zhou Gaoshengda Technology Co.,LTD Addresss NO.75 Zhongkai Development Area City / ZIP / State / Country Huizhou, Guangdong, China request modular approval for the certification of our equipment within this application, identified by: FCC ID: 2AC23-WT31M2311A The table below contains the justification for modular approval of this equipment: Requirement per 15.212 and KDB 996369 D01 Module Equip Auth Guide v02 Explanation from grantee (do not write yes / no, but explain why it complies / how it is achieved) 1. The modular transmitter must have its own RF shielding. Yes (The modular equip with own RF shielding case) 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are Yes provided) to ensure that the module will comply with Part 15 requirements under (The modular data inputs are buffered through log conditions of excessive data rates or over-modulation. or micro-controller connections) 3. The modular transmitter must have its own power supply regulation. Yes (RF voltage regulation is handled on the module) 4. The modular transmitter must comply with the antenna requirements of Section 15.203 Yes and 15.204(c). The antenna must either be permanently attached or employ a “unique” (The modular with permanently antenna, the antenna coupler (at all connections between the module and the antenna, including the antenna is FPC Antenna) cable).. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module Yes must not be inside another device during testing. This is intended to demonstrate that the (The module was tested stand-alone) module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC Yes ID is not visible when the module is installed inside another device, then the outside of the (Please refer to FCC ID label) device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating requirements Yes applicable to the transmitter and the manufacturer must provide adequate instructions (Please refer to the modular installation manual) along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF exposure requirements. Yes For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, (Please see the MPE report, the modular meets including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII MPE calculation of 47 CFR 1.107 (b)(1).) and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Attestation (by grantee) City and Country: Date: Name: Function: Signature: (this must be a person) (or official company stamp) Huizhou, China 2016-12-06 Hui Guan Manager


Document Created: 2019-06-08 17:31:27
Document Modified: 2019-06-08 17:31:27
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC