HAC RF Emission Test Report

FCC ID: 2ABZ2-EE133

Test Report

Download: PDF
FCCID_4476250

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A HEARING AID COMPATIBILITY RF EMISSIONS TEST REPORT FCC ID : 2ABZ2-EE133 Equipment : Smart Phone Brand Name : ONEPLUS Model Name : HD1905 M-Rating : M3 Applicant : OnePlus Technology (Shenzhen) Co., Ltd 18C02, 18C03, 18C04 and 18C05, Shum Yip Terra Building, Binhe Avenue North, Futian District, Shenzhen Manufacturer : OnePlus Technology (Shenzhen) Co., Ltd 18C02, 18C03, 18C04 and 18C05, Shum Yip Terra Building, Binhe Avenue North, Futian District, Shenzhen Standard : FCC 47 CFR §20.19 ANSI C63.19-2011 The product was received on Jul. 09, 2019 and testing was started from Jul. 19, 2019 and completed on Aug. 03, 2019. We, SPORTON INTERNATIONAL INC., would like to declare that the tested sample has been evaluated in accordance with the test procedures and has been in compliance with the applicable technical standards. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any agency of government. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory, the test report shall not be reproduced except in full. Approved by: Cona Huang / Deputy Manager SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City, Taiwan (R.O.C.) TEL : 886-3-327-3456 Page : 1 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 180516

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A Table of Contents 1. General Information ................................................................................................................................................... 4 2. Testing Location......................................................................................................................................................... 5 3. Applied Standards ..................................................................................................................................................... 5 4. RF Audio Interference Level...................................................................................................................................... 5 5. Air Interface and Operating Mode............................................................................................................................. 6 6. Measurement System Specification ......................................................................................................................... 7 E-Field Probe System .................................................................................................................................................. 7 Data Storage and Evaluation ....................................................................................................................................... 8 7. RF Emissions Test Procedure................................................................................................................................... 9 8. Test Equipment List ..................................................................................................................................................12 9. Measurement System Validation .............................................................................................................................13 10. Modulation Interference Factor................................................................................................................................14 11. Low-power Exemption ..............................................................................................................................................15 12. Conducted RF Output Power (Unit: dBm) ...............................................................................................................18 13. HAC RF Emission Test Results ................................................................................................................................20 14. Uncertainty Assessment ..........................................................................................................................................21 15. References .................................................................................................................................................................23 Appendix A. Plots of System Performance Check Appendix B. Plots of RF Emission Measurement Appendix C. DASY Calibration Certificate Appendix D. Test Setup Photos TEL : 886-3-327-3456 Page : 2 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A History of this test report Report No. Version Description Issued Date HA970203-03A Rev. 01 Initial issue of report Sep. 25, 2019 TEL : 886-3-327-3456 Page : 3 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A 1. General Information Product Feature & Specification Applicant Name OnePlus Technology (Shenzhen) Co., Ltd Equipment Name Smart Phone Brand Name ONEPLUS Model Name HD1905 FCC ID 2ABZ2-EE133 EUT Stage Production Unit Date Tested 2019/7/19 ~ 2019/8/3 GSM850: 824.2 MHz ~ 848.8 MHz GSM1900: 1850.2 MHz ~ 1909.8 MHz WCDMA Band II: 1852.4 MHz ~ 1907.6 MHz WCDMA Band IV: 1712.4 MHz ~ 1752.6 MHz WCDMA Band V: 826.4 MHz ~ 846.6 MHz CDMA2000 BC0: 824.7 MHz ~ 848.31 MHz CDMA 2000 BC1: 1851.25 MHz ~ 1908.75 MHz CDMA 2000 BC10: 817.9 MHz ~ 823.1 MHz LTE Band 2: 1850.7 MHz ~ 1909.3 MHz LTE Band 4: 1710.7 MHz ~ 1754.3 MHz LTE Band 5: 824.7 MHz ~ 848.3 MHz LTE Band 7: 2502.5 MHz ~ 2567.5 MHz LTE Band 12: 699.7 MHz ~ 715.3 MHz LTE Band 13: 779.5 MHz ~ 784.5 MHz LTE Band 17: 706.5 MHz ~ 713.5 MHz Frequency Band LTE Band 25: 1850.7 MHz ~ 1914.3 MHz LTE Band 26: 814.7 MHz ~ 848.3 MHz LTE Band 30: 2307.5 MHz ~ 2312.5 MHz LTE Band 38: 2572.5 MHz ~ 2617.5 MHz LTE Band 41: 2498.5 MHz ~ 2687.5 MHz LTE Band 48: 3552.5 MHz ~ 3697.5 MHz LTE Band 66: 1710.7 MHz ~ 1779.3 MHz LTE Band 71: 665.5 MHz ~ 695.5 MHz WLAN 2.4GHz Band: 2412 MHz ~ 2462 MHz WLAN 5.2GHz Band: 5180 MHz ~ 5240 MHz WLAN 5.3GHz Band: 5260 MHz ~ 5320 MHz WLAN 5.5GHz Band: 5500 MHz ~ 5720 MHz WLAN 5.8GHz Band: 5745 MHz ~ 5825 MHz Bluetooth: 2402 MHz ~ 2480 MHz NFC: 13.56 MHz GSM/GPRS/EGPRS AMR / RMC 12.2Kbps HSDPA HSUPA DC-HSDPA Mode HSPA+ (16QAM uplink) CDMA2000 : 1xRTT/1xEv-Do(Rel.0)/1xEv-Do(Rev.A) LTE: QPSK, 16QAM, 64QAM 802.11a/b/g/n/ac HT20/HT40/VHT20/VHT40/VHT80 Bluetooth BR/EDR/LE NFC:ASK Remark: 1. This is a variant report to enable dual SIM slot and change model name, and the changes didn’t affect the test results, all the test cases are referred from Sporton HAC report, report number HA970203A (FCC ID: 2ABZ2-EE133) 2. This device has WWAN UAT and LAT transmitter antennas. LAT antenna as ANT3 is located at the bottom edge of the device; UAT antenna as ANT0/2 is located at the left side of top edge of the device, and which can refer to antenna location chapter. 3. The 2.4GHz/5GHz WLAN can transmit in MIMO antenna mode only and it has no SISO antenna mode. Reviewed by: Jason Wang Report Producer: Wan Liu TEL : 886-3-327-3456 Page : 4 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

seortron ias._HAC RF EMISSIONS TEST REPORT Report No. : HA970203—03A 2. Testing Location Sporton Lab is accredited to ISO 17025 by Taiwan Accreditation Foundation (TAF code: 1190) and the FCC designation No. TW 1190 under the FCC 2.948(e) by Mutual Recognition Agreement (MRA) in FCC test. Testing Laboratory [Csc SPORTON INTERNATIONAL INC. No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City, Taiwan (R.0.C.) Test Site Location TEL: +886—3—327—3456 FAX: +886—3—328—4978 B Sporton Site No.: 1Cc SAROA—HY 3. Applied Standards + FCC CFR47 Part 20.19 + ANSIC63.19—2011 + FCC KDB 285076 DO1 HAC Guidance v05 +_ FCC KDB 285076 DO2 T Coil testing v03 +__FCC KDB 285076 D03 HAC FAQ v01 4. RF Audio Interference Level FCC wireless hearing aid compatibility rules ensure that consumers with hearing loss are able to access wireless communications services through a wide selection of handsets without experiencing disabling radio frequency (RF) interference or other technical obstacles. To define and measure the hearing aid compatibility of handsets, in CFR47 part 20.19 ANSI €C63.19 is referenced. A handset is considered hearing aid—compatible for acoustic coupling if it meets a rating of at least M3 under ANSI C©63.19, and A handset is considered hearing aid compatible for inductive coupling if it meets a rating of at least T3. According to ANSI €63.19 2011 version, for acoustic coupling, the RF electric field emissions of wireless communication devices should be measured and rated according to the emission level as below. E—field emissions Emission Categories <960Mhz >960Mhz M1i 50 to 55 dB (V/m) 40 to 45 dB (V/m) M2 45 to 50 dB (V/m) 35 to 40 dB (V/m) M3 40 to 45 dB (V/m) 30 to 35 dB (V/m) M4 <40 dB (V/m) <30 dB (V/m) Table 5.1 Telephone near—field categories in linear units TEL : 886—3—327—3456 Page : 5 of 23 FAX : 886—3—328—4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A 5. Air Interface and Operating Mode Air C63.19 Simultaneous Name of Voice Power Interface Band MHz Type Tested Transmitter Service Reduction GSM850 WLAN, BT No VO Yes CMRS Voice GSM1900 WLAN, BT No GSM SIP calling(2) EDGE850 WLAN, BT VD Yes / No EDGE1900 WLAN, BT Google Duo 850 WLAN, BT No 1750 VO No(1) WLAN, BT CMRS Voice No WCDMA 1900 WLAN, BT No SIP calling(2) HSPA VD No(1) WLAN, BT / No Google Duo BC0 WLAN, BT No BC1 VO Yes WLAN, BT CMRS Voice No CDMA BC10 WLAN, BT No SIP calling(2) (1) EVDO VD No WLAN, BT / No Google Duo Band 2 WLAN, BT No Band 4 WLAN, BT No Band 5 WLAN, BT No Band 7 WLAN, BT No Band 12 WLAN, BT VoLTE No Band 13 WLAN, BT / No LTE VD No(1) SIP calling(2) (FDD) Band 17 WLAN, BT No / Band 25 WLAN, BT Google Duo No Band 26 WLAN, BT No Band 30 WLAN, BT No Band 66 WLAN, BT No Band 71 WLAN, BT No Band 38 WLAN, BT VoLTE No / LTE Band 41 VD Yes WLAN, BT SIP calling(2) No (TDD) / Band 48 WLAN, BT Google Duo No 2450 No VoWiFi 5200 / No Wi-Fi 5300 VD No(1) GSM,CDMA,WCDMA,LTE,BT SIP calling(2) No 5500 / No Google Duo 5800 No BT 2450 DT No GSM,CDMA,WCDMA,LTE,WLAN NA No Type Transport: VO= Voice only DT= Digital Transport only (no voice) VD= CMRS and IP Voice Service over Digital Transport Remark: 1. The air interface is exempted from testing by low power exemption that its average antenna input power plus its MIF is ≤17 dBm, and is rated as M4. 2. The SIP calling is android internal auxiliary functions under the dialing program. 3. According to ANSI C63.19 2011 -version, for the air interface technology of a device is exempt from testing whose peak antenna input power, averaged over intervals ≤50 μs, is ≤23 dBm. An RF air interface technology that is exempted from testing shall be rated as M4. 4. The device have similar frequency in some LTE bands: LTE 38/41, since the supported frequency spans for the smaller LTE bands are completely cover by the larger LTE bands, therefore, only larger LTE bands were required to be tested for hearing-aid compliance. TEL : 886-3-327-3456 Page : 6 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

seorrow cas. _HAC RF EMISSIONS TEST REPORT Report No. : HA970203—03A 6. Measurement System Specification Remote Control Box PC O <———— O e= Signal Lamps Electo—Ortical Commerter (E0C) <tlk» oae (Ost. Ling E Measurement Server E—feld ortfeld Probe Light Beam Device Under Test 2x Serial + = Digtal ¥O Phantom~— I—Device Holder — Teach Pendant C——I Robot Controller O O Fig 5.1 System Configurations E—Field Probe System E—Field Probe Specification <ER3DV6> Construction One dipole parallel, two dipoles normal to probe axis Built—in shielding against static charges Calibration In air from 100 MHz to 3.0 GHz (absolute accuracy +6.0%, k=2) Frequency 100 MHz to 6 GHz; Linearity: + 2.0 dB (100 MHz to 3 GHz) Directivity + 0.2 dB in air (rotation around probe axis) + 0.4 dB in air (rotation normal to probe axis) Dynamic Range 2 V/m to 1000 V/m (M3 or better device readings fall well below diode compression point) Linearity +0.2 dB Dimensions Overall length: 330 mm (Tip: 16 mm) Tip diameter: 8 mm (Body: 12 mm) Distance from probe tip to dipole centers: 2.5 mm Fig 5.2 Photo of E—field Probe Probe Tip Description: HAC field measurements take place in the close near field with high gradients. Increasing the measuring distance from the source will generally decrease the measured field values (in case of the validation dipole approx. 109&per mm}. TEL : 886—3—327—3456 Page : 7 of 23 FAX : 886—3—328—4978 Issued Date : Sep. 25, 2019 Form version: 181113

seorton cas. _HAC RF EMISSIONS TEST REPORT Report No. : HA970203—03A Data Storage and Evaluation The DASY software stores the assessed data from the data acquisition electronics as raw data (in microvolt readings from the probe sensors), together with all the necessary software parameters for the data evaluation {probe calibration data, and device frequency and modulation data) in measurement files. Probe parameters : — Sensitivity NOFM;: &ip; Aits Siz — Conversion factor ConvF; — Diode compression point dep; Device parameters : — Frequency f — Crest factor cf Media parameters : — Conductivity 0 — Density p The formula for each channel can be given as : , _of Vi:Ui+Ui W i with V; = compensated signal of channel i, (i= x, y, z) U; = input signal of channel i, (i =x, y, z) cf = crest factor of exciting field (DASY parameter) dep; = diode compression point (DASY parameter) From the compensated input signals, the primary field data for each channel can be evaluated : V E—field Probes : E; = Normp—ConvF with V; = compensated signal of channel i, (i= x, y, z) Norm; = sensor sensitivity of channel i, (i=x, y, z), pV/(V/m)2 for E—field Probes ConvF = sensitivity enhancement in solution f = carrier frequency [GHz] E; = electric field strength of channel i in V/m The RSS value of the field components gives the total field strength (Hermitian magnitude) : Eror = _[E2 + EJ + E2 The primary field data are used to calculate the derived field units. TEL : 886—3—327—3456 Page : 8 of 23 FAX : 886—3—328—4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A 7. RF Emissions Test Procedure Referenced from ANSI C63.19 -2011 section 5.5.1 a. Confirm the proper operation of the field probe, probe measurement system, and other instrumentation and the positioning system. b. Position the WD in its intended test position. c. Set the WD to transmit a fixed and repeatable combination of signal power and modulation characteristic that is representative of the worst case (highest interference potential) encountered in normal use. Transiently occurring start-up, changeover, or termination conditions, or other operations likely to occur less than 1% of the time during normal operation, may be excluded from consideration. d. The center sub-grid shall be centered on the T-Coil mode perpendicular measurement point or the acoustic output, as appropriate. Locate the field probe at the initial test position in the 50 mm by 50 mm grid, which is contained in the measurement plane, refer to illustrated in Figure 8.2. If the field alignment method is used, align the probe for maximum field reception. e. Record the reading at the output of the measurement system. f. Scan the entire 50 mm by 50 mm region in equality spaced increments and record the reading at each measurement point, The distance between measurement points shall be sufficient to assure the identification of the maximum reading. g. Identify the five contiguous sub-grids around the center sub-grid whose maximum reading is the lowest of all available choices. This eliminates the three sub-grids with the maximum readings. Thus, the six areas to be used to determine the WD's highest emissions are identified. h. Identify the maximum reading within the non-excluded sub-grids identified in step g). i. Indirect measurement method j. The RF audio interference level in dB (V/m) is obtained by adding the MIF (in dB) to the maximum steady-state rms field-strength reading, in dB (V/m) k. Compare this RF audio interference level with the categories in ANSI C63.19-2011 clause 8 and record the resulting WD category rating. l. For the T-Coil perpendicular measurement location is ≥5.0 mm from the center of the acoustic output, then two different 50 mm by 50 mm areas may need to be scanned, the first for the microphone mode assessment and the second for the T-Coil assessment. m. The second for the T-Coil assessment, with the grid shifted so that it is centered on the perpendicular measurement point. Record the WD category rating. TEL : 886-3-327-3456 Page : 9 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A Figure 8.1 RF Emissions Flow Chart TEL : 886-3-327-3456 Page : 10 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A Fig 8.2 EUT reference and plane for HAC RF emission measurements Fig. 8.3 Gauge block with E-field probe TEL : 886-3-327-3456 Page : 11 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A 8. Test Equipment List Calibration Manufacturer Name of Equipment Type/Model Serial Number Last Cal. Due Date SPEAG 835MHz Calibration Dipole CD835V3 1045 Sep. 19, 2018 Sep. 18, 2019 SPEAG 1880MHz Calibration Dipole CD1880V3 1038 Sep. 19, 2018 Sep. 18, 2019 SPEAG 2600Mhz Calibration Dipole CD2600V3 1018 Aug. 22, 2018 Aug. 21, 2019 SPEAG 3500Mhz Calibration Dipole CD3500V3 1009 Feb. 18, 2019 Feb. 17, 2020 SPEAG Isotropic E-Field Probe EF3DV3 4047 Jan. 30, 2019 Jan. 29, 2020 SPEAG Isotropic E-Field Probe EF3DV3 4053 Apr. 16, 2019 Apr. 15, 2020 SPEAG Data Acquisition Electronics DAE4 914 Jun. 20, 2019 Jun. 19, 2020 SPEAG Data Acquisition Electronics DAE4 1437 Oct. 15, 2018 Oct. 14, 2019 RCPTWN Thermometer HTC-1 TM560-2 Nov. 12, 2018 Nov. 11, 2019 SPEAG Test Arch Phantom N/A N/A NCR NCR SPEAG Phone Positioner N/A N/A NCR NCR Anritsu Power Meter ML2495A 1218006 Oct. 08, 2018 Oct. 07, 2019 Anritsu Power Sensor MA2411B 1207363 Oct. 08, 2018 Oct. 07, 2019 Anritsu Signal Generator MG3710A 6201502524 Dec. 11, 2018 Dec. 10, 2019 R&S Base Station CMW500 115793 Jun. 04, 2019 Jun. 03, 2020 R&S Base Station CMU200 103937 Jan. 17, 2019 Jan. 16, 2020 ATM Dual Directional Coupler C122H-10 P610410z-02 NCR NCR Woken Attenuator WK0602-XX N/A NCR NCR Mini-Circuits Power Amplifier ZVE-8G+ 070501814 Oct. 08, 2018 Oct. 07, 2019 Mini-Circuits Power Amplifier ZHL-42W+ 715701915 May. 10, 2019 May. 09, 2020 Note: 1. NCR: “No-Calibration Required” TEL : 886-3-327-3456 Page : 12 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A 9. Measurement System Validation Each DASY system is equipped with one or more system validation kits. These units, together with the predefined measurement procedures within the DASY software, enable the user to conduct the system performance check and system validation. System validation kit includes a dipole, tripod holder to fix it underneath the test Arch and a corresponding distance holder. The system performance check verifies that the system operates within its specifications. System and operator errors can be detected and corrected. It is recommended that the system performance check be performed prior to any usage of the system in order to guarantee reproducible results. The system performance check uses normal HAC measurements in a simplified setup with a well characterized source. This setup was selected to give a high sensitivity to all parameters that might fail or vary over time. The system check does not intend to replace the calibration of the components, but indicates situations where the system uncertainty is exceeded due to drift or failure. <Test Setup> 1. In the simplified setup for system evaluation, the EUT is replaced by a calibrated dipole and the power source is replaced by a continuous wave which comes from a signal generator. 2. The center point of the probe element(s) is 15mm from the closest surface of the dipole elements. 3. The calibrated dipole must be placed beneath the arch phantom. The equipment setup is shown below: 4. The output power on dipole port must be calibrated to 20dBm (100mW) before dipole is connected. Fig. 7.1 Setup Diagram <Validation Results> Comparing to the original E-field value provided by SPEAG, the verification data should be within its specification of 25 %. Table 6.1 shows the target value and measured value. The table below indicates the system performance check can meet the variation criterion and the plots can be referred to appendix A of this report. Deviation = ((Average E-field Value) - (Target value)) / (Target value) * 100% Frequency Input Power Target Value E-Field 1 E-Field 2 Average Value Deviation Date (MHz) (dBm) (V/m) (V/m) (V/m) (V/m) (%) 835 20 108.8 108.5 112.4 110.45 1.52 Jul 19, 2019 1880 20 89.5 86.62 90.15 88.385 -1.25 Jul 19, 2019 1880 20 89.5 95.27 96.63 95.95 7.21 Aug 03, 2019 2600 20 85.8 87.15 87.12 87.135 1.56 Jul 19, 2019 3500 20 84.6 88.15 87 87.575 3.52 Jul 20, 2019 TEL : 886-3-327-3456 Page : 13 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A 10. Modulation Interference Factor The HAC Standard ANSI C63.19-2011 defines a new scaling using the Modulation Interference Factor (MIF). For any specific fixed and repeatable modulated signal, a modulation interference factor (MIF, expressed in dB) may be developed that relates its interference potential to its steady-state rms signal level or average power level. This factor is a function only of the audio-frequency amplitude modulation characteristics of the signal and is the same for field-strength and conducted power measurements. It is important to emphasize that the MIF is valid only for a specific repeatable audio-frequency amplitude modulation characteristic. Any change in modulation characteristic requires determination and application of a new MIF The Modulation Interference factor (MIF, in dB) is added to the measured average E-field (in dBV/m) and converts it to the RF Audio Interference level (in dBV/m). This level considers the audible amplitude modulation components in the RF E-field. CW fields without amplitude modulation are assumed to not interfere with the hearing aid electronics. Modulations without time slots and low fluctuations at low frequencies have low MIF values, TDMA modulations with narrow transmission and repetition rates of few 100 Hz have high MIF values and give similar classifications as ANSI C63.19-2011. ER3D, EF3D and EU2D E-field probes have a bandwidth <10 kHz and can therefore not evaluate the RF envelope in the full audio band. DASY52 is therefore using the indirect measurement method according to ANSI C63.19-2011 which is the primary method. These near field probes read the averaged E-field measurement. Especially for the new high peak-to-average (PAR) signal types, the probes shall be linearized by PMR calibration in order to not overestimate the field reading. Probe Modulation Response (PMR) calibration linearizes the probe response over its dynamic range for specific modulations which are characterized by their UID and result in an uncertainty specified in the probe calibration certificate. The MIF is characteristic for a given waveform envelope and can be used as a constant conversion factor if the probe has been PMR calibrated. The evaluation method for the MIF is defined in ANSI C63.19-2011 section D.7. An RMS demodulated RF signal is fed to a spectral filter (similar to an A weighting filter) and forwarded to a temporal filter acting as a quasi-peak detector. The averaged output of these filtering is scaled to a 1 kHz 80% AM signal as reference. MIF measurement requires additional instrumentation and is not well suited for evaluation by the end user with reasonable uncertainty. It may alliteratively be determined through analysis and simulation, because it is constant and characteristic for a communication signal. DASY52 uses well-defined signals for PMR calibration. The MIF of these signals has been determined by simulation and it is automatically applied. The MIF measurement uncertainty is estimated as follows, declared by HAC equipment provider SPEAG, for modulation frequencies from slotted waveforms with fundamental frequency and at least 2 harmonics within 10 kHz: 1. 0.2 dB for MIF: -7 to +5 dB 2. 0.5 dB for MIF: -13 to +11 dB 3. 1 dB for MIF: > -20 dB MIF values applied in this test report were provided by the HAC equipment provider of SPEAG, and the worst values for all air interface are listed below to be determine the Low-power Exemption. UID Communication System Name MIF(dB) 10021 GSM-FDD(TDMA,GMSK) 3.63 10025 EDGE-FDD (TDMA, 8PSK, TN 0) 3.75 10460 UMTS-FDD(WCDMA, AMR) -25.43 10225 UMTS-FDD (HSPA+) -20.39 10081 CDMA2000 (1xRTT, RC3) -19.71 10295 CDMA2000 (1xRTT, RC1 SO3, 1/8th Rate 25 fr.) 3.26 10403 CDMA2000 (1xEV-DO, Rev. 0) -17.67 10170 LTE-FDD(SC-FDMA,1RB,20MHz,16-QAM) -9.76 10172 LTE-TDD (SC-FDMA, 1 RB, 20 MHz, QPSK) -1.62 10173 LTE-TDD (SC-FDMA, 1 RB, 20 MHz, 16-QAM) -1.44 10174 LTE-TDD (SC-FDMA, 1 RB, 20 MHz, 64-QAM) -1.54 10061 IEEE 802.11b WiFi 2.4 GHz (DSSS, 11 Mbps) -2.02 10077 IEEE 802.11g WiFi 2.4 GHz (DSSS/OFDM, 54 Mbps) 0.12 10427 IEEE 802.11n (HT Greeneld, 150 Mbps, 64-QAM) -13.44 10069 IEEE 802.11a/h WiFi 5 GHz (OFDM, 54 Mbps) -3.15 10616 IEEE 802.11ac WiFi (40MHz, MCS0, 90pc duty cycle) -5.57 TEL : 886-3-327-3456 Page : 14 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A 11. Low-power Exemption <Max Tune-up Limit> Average Power (dBm) Mode UAT LAT GSM850 30.8 EDGE850 24.8 GSM GSM1900 28.9 30.3 EDGE1900 24.4 25.8 Band II 20.4 24.8 Band IV 20.4 24.8 WCDMA Band V 21.3 HSPA 20.3 23.8 BC0 21.8 BC1 20.9 24.8 CDMA BC10 21.8 EVDO 21.8 24.8 Band 2 19.4 23.8 Band 4 18.9 23.8 Band 5 19.8 Band 7 15.5 23.8 Band 12 20.8 Band 13 21.3 FDD LTE Band 17 20.8 Band 25 19.4 23.8 Band 26 19.8 Band 30 16 23.8 Band 66 18.9 23.8 Band 71 22.8 QPSK 18 23.8 Band 38 16QAM 18 22.8 64QAM 18 21.8 QPSK 20 26.3 Band 16QAM 20 25.3 41_PC2 64QAM 20 24.3 TDD LTE QPSK 18 23.8 Band 16QAM 18 22.8 41_PC3 64QAM 18 21.8 QPSK 16.8 Band 48 16QAM 16.8 64QAM 16.8 Average Power (dBm) Mode ANT1+2 802.11b 16 802.11g 15 802.11n-HT20 15 2.4GHz WLAN 802.11n-HT40 13 802.11ac-VHT20 15 802.11ac-VHT40 13 802.11a 20 802.11n-HT20 20 802.11n-HT40 20 5GHz WLAN 802.11ac-VHT20 20 802.11ac-VHT40 20 802.11ac-VHT80 19 TEL : 886-3-327-3456 Page : 15 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A <Low Power Exemption> Max Average Worst Case Power + C63.19 test Air Interface Antenna Input MIF (dB) MIF(dB) required Power (dBm) UAT 30.8 3.63 34.43 Yes GSM850 LAT UAT 24.8 3.75 28.55 Yes(1) EDGE850 LAT UAT 28.9 3.63 32.53 Yes GSM1900 LAT 30.3 3.63 33.93 Yes UAT 24.4 3.75 28.15 Yes(1) EDGE1900 LAT 25.8 3.75 29.55 Yes(1) UAT 21.3 -25.43 -4.13 No WCDMA LAT 24.8 -25.43 -0.63 No WCDMA - UAT 20.3 -20.39 -0.09 No HSPA LAT 23.8 -20.39 3.41 No CDMA Full UAT 21.8 -19.71 2.09 No Frame Rate LAT 24.8 -19.71 5.09 No CDMA 1/8th UAT 21.8 3.26 25.06 Yes Frame Rate LAT 24.8 3.26 28.06 Yes UAT 21.8 -17.67 4.13 No CDMA - EVDO LAT 24.8 -17.67 7.13 No UAT 22.8 -9.76 13.04 No LTE - FDD LAT 23.8 -9.76 14.04 No QPSK 20 -1.62 18.38 Yes LTE B41_PC2 16QAM 20 -1.44 18.56 Yes(1) UAT 64QAM 20 -1.54 18.46 Yes(1) QPSK 26.3 -1.62 24.68 Yes LTE B41_PC2 16QAM 25.3 -1.44 23.86 Yes(1) LAT 64QAM 24.3 -1.54 22.76 Yes(1) QPSK 18 -1.62 16.38 No LTE B41_PC3 16QAM 18 -1.44 16.56 No UAT 64QAM 18 -1.54 16.46 No QPSK 23.8 -1.62 22.18 Yes LTE B41_PC3 16QAM 22.8 -1.44 21.36 Yes(1) LAT 64QAM 21.8 -1.54 20.26 Yes(1) QPSK 16.8 -1.62 15.18 No LTE B48 16QAM 16.8 -1.44 15.36 No UAT 64QAM 16.8 -1.54 15.26 No General Note: 1. EDGE data modes and 16QAM/64QAM is not necessary due the GSM Voice mode and QPSK is the worst case. 2. According to ANSI C63.19 2011-version, for the air interface technology of a device is exempt from testing when its average antenna input power plus its MIF is ≤17 dBm for any of its operating modes. 3. HAC RF rating is M4 for the air interface which meets the low power exemption. TEL : 886-3-327-3456 Page : 16 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A Max Average Worst Case Power + C63.19 test Air Interface Antenna Input MIF (dB) MIF(dB) required Power (dBm) 802.11b ANT1+2 16 -2.02 13.98 No 802.11g ANT1+2 15 0.12 15.12 No 802.11n-HT20 ANT1+2 15 -13.44 1.56 No 802.11n-HT40 ANT1+2 13 -13.44 -0.44 No 802.11ac-VHT20 ANT1+2 15 -5.57 9.43 No 802.11ac-VHT40 ANT1+2 13 -5.57 7.43 No 802.11a ANT1+2 20 -3.15 16.85 No 802.11n-HT20 ANT1+2 20 -13.44 6.56 No 802.11n-HT40 ANT1+2 20 -13.44 6.56 No 802.11ac-VHT20 ANT1+2 20 -5.57 14.43 No 802.11ac-VHT40 ANT1+2 20 -5.57 14.43 No 802.11ac-VHT80 ANT1+2 19 -5.57 13.43 No General Note: 1. According to ANSI C63.19 2011-version, for the air interface technology of a device is exempt from testing when its average antenna input power plus its MIF is ≤17 dBm for any of its operating modes. 2. HAC RF rating is M4 for the air interface which meets the low power exemption. TEL : 886-3-327-3456 Page : 17 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A 12. Conducted RF Output Power (Unit: dBm) <UAT> Average Antenna Input Power(dBm) Band GSM850 GSM1900 Channel 128 189 251 512 661 810 Frequency (MHz) 824.2 836.4 848.8 1850.2 1880.0 1909.8 GSM (GMSK, 1 Tx slot) 30.33 30.15 29.93 28.31 28.14 28.26 Band CDMA2000 BC0 CDMA2000 BC1 CDMA2000 BC10 TX Channel 1013 384 777 25 600 1175 476 580 684 Frequency (MHz) 824.7 836.52 848.31 1851.25 1880 1908.75 817.9 820.5 823.1 1xRTT RC1 SO3, 1/8th Rate 21.27 20.98 20.86 20.25 20.19 20.34 21.24 21.26 21.21 <LAT> Average Antenna Input Power(dBm) Band GSM1900 Channel 512 661 810 Frequency (MHz) 1850.2 1880 1909.8 GSM (GMSK, 1 Tx slot) 29.45 29.41 29.43 Band CDMA2000 BC1 TX Channel 25 600 1175 Frequency (MHz) 1851.25 1880 1908.75 1xRTT RC1 SO3, 1/8th Rate 23.89 23.86 24.03 TEL : 886-3-327-3456 Page : 18 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A <LTE B41_PC2 UAT> Power Power Power Power Power BW [MHz] Modulation RB Size RB Offset Low Low Middle Middle High Middle High Ch. / Freq. Ch. / Freq. Ch. / Freq. Ch. / Freq. Ch. / Freq. Channel 39750 40185 40620 41055 41490 Frequency (MHz) 2506 2549.5 2593 2636.5 2680 20 QPSK 1 99 19.52 19.53 19.67 18.94 19.34 <LTE B41_PC2 LAT> Power Power Power Power Power BW [MHz] Modulation RB Size RB Offset Low Low Middle Middle High Middle High Ch. / Freq. Ch. / Freq. Ch. / Freq. Ch. / Freq. Ch. / Freq. Channel 39750 40185 40620 41055 41490 Frequency (MHz) 2506 2549.5 2593 2636.5 2680 20 QPSK 1 99 25.91 25.62 26.03 25.24 25.52 <LTE B41_PC3 LAT> Power Power Power Power Power BW [MHz] Modulation RB Size RB Offset Low Low Middle Middle High Middle High Ch. / Freq. Ch. / Freq. Ch. / Freq. Ch. / Freq. Ch. / Freq. Channel 39750 40185 40620 41055 41490 Frequency (MHz) 2506 2549.5 2593 2636.5 2680 20 QPSK 1 99 23.43 23.60 23.67 22.99 23.13 TEL : 886-3-327-3456 Page : 19 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

seorrow cas. _HAC RF EMISSIONS TEST REPORT Report No. : HA970203—03A 13. HAC RF Emission Test Results GSMBso GSM Voice UAT 80.33 3.63 38.13 6.87 M4 GSMBso GSM Voice UAT 80.15 3.63 38.37 6.63 M4 GSMBso GSM Voice UAT 20.93 8.63 87.85 715 M4 GSM1900 GSM Voice UAT 28.31 3.63 33.60 1.40 M3 GSM1900 GSM Voice UAT 28.14 3.63 33.43 157 M3 GSM1900 GSM Voice UAT 28.26 8.63 83.27 1.73 M3 GSM1900 GSM Voice LAT 20.45 8.63 80.05 4.95 M3 GSM1900 GSM Voice LAT 20.41 3.63 20.29 5.71 M4 GSM1900 GSM Voice LAT 20.43 8.63 28.15 685 M4 10 GDMA 8C0 1xRTT, RG1 $03, 1/8th Rate UAT 21.27 3.26 20.42 15.58 M4 11 GDMA 8C0 1xRTT, RG1 $03, 1/8th Rate UAT 20.98 3.26 20.56 1544 M4 12 GDMA 8C0 1xRTT, RG1 $03, 1/8th Rate UAT 20.86 3.26 28.43 16.57 M4 13 CDMA BC1 1xRTT, RG1 $03, 1/8th Rate 25 UaAT 20.25 8.26 80.77 4.23 M3 14 GDMA BC1 1xRTT, RC1 $03, 1/8th Rate 600 UAT 20.19 3.26 80.74 4.26 M3 15 GDMA BC1 1xRTT, RG1 $03, 1/8th Rate 1175 UaAT 20.34 3.26 80.58 4.42 M3 16 GDMA BC1 1xRTT, RG1 $03, 1/8th Rate 25 LAT 23.89 3.26 18.50 16.50 M4 17 GDMA BC1 1xRTT, RG1 $03, 1/8th Rate 600 LAT 23.86 3.26 25.82 9.18 M4 18 GDMA BC1 1xRTT, RG1 $03, 1/8th Rate 1175 LAT 24.03 3.26 22.21 12.79 M4 19 CDMA BG10 1xRTT, RG1 $03, 1/8th Rate 476 UAT 21.24 3.26 20.70 15.30 M4 20 GDMA B8G10 1xRTT, RG1 $03, 1/8th Rate 580 UAT 21.26 3.26 20.56 1544 M4 21 CDMA BG10 1xRTT, RG1 $03, 1/8th Rate 684 UAT 21.21 3.26 20.48 15.52 M4 22 LTE Band 41_PGS 20M_GPSK_1_99 89750 LAT 23.43 1.62 22.75 1225 M4 23 LTE Band 41_PGS 20M_GPSK_1_99 40185 LAT 23.60 1.62 23.03 11.97 M4 24 LTE Band 41_PGS 20M_GPSK_1_99 40620 LAT 23.67 1.62 23.13 11.87 M4 25 LTE Band 41_PGS 20M_GPSK_1_99 41055 LAT 22.99 41.62 23.77 11.23 M4 26 LTE Band 41_PGS 20M_GPSK_1_99 41490 LAT 23.13 41.62 24.68 10.32 M4 27 LTE Band 41_PG2 20M_GPSK_1_99 89750 LAT 25.91 41.62 21.97 13.03 M4 28 LTE Band 41_PG2 20M_GPSK_1_99 40185 LAT 25.62 41.62 23.67 11.33 M4 20 LTE Band 41_PG2 20M_GPSK_1_99 40620 LAT 26.03 41.62 23.60 11.31 M4 so LTE Band 41_PG2 20M_GPSK_1_99 41055 LAT 25.24 1.62 23.74 11.26 M4 81 LTE Band 41_PG2 20M_GPSK_1_99 41490 LAT 25.52 41.62 24.50 10.50 M4 82 LTE Band 41_PG2 20M_GPSK_1_99 89750 UaAT 19.52 41.62 83.18 1.82 M3 33 LTE Band 41_PG2 20M_GPSK_1_99 40185 UAT 19.53 1.62 33.36 164 M3 34 LTE Band 41_PG2 20M_GPSK_1_99 40620 UAT 19.67 1.62 33.05 1.95 M3 35 LTE Band 41_PG2 20M_GPSK_1_99 41055 UAT 18.94 41.62 82.03 2.97 M3 86 LTE Band 41_PG2 20M_GPSK_1_99 41490 UAT 19.34 41.62 82.01 2.99 M3 Remark: 1. The HAC measurement system applies MIF value onto the measured RMS E—field, which is indirect method in ANSI ©63.19 2011 version, and reports the RF audio interference level. 2. Phone Condition: Mute on; Backlight off; Max Volume Test Engineer : NickYu. TEL : 886—3—327—3456 Page : 20 of 23 FAX : 886—3—328—4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A 14. Uncertainty Assessment The component of uncertainly may generally be categorized according to the methods used to evaluate them. The evaluation of uncertainly by the statistical analysis of a series of observations is termed a Type A evaluation of uncertainty. The evaluation of uncertainty by means other than the statistical analysis of a series of observation is termed a Type B evaluation of uncertainty. Each component of uncertainty, however evaluated, is represented by an estimated standard deviation, termed standard uncertainty, which is determined by the positive square root of the estimated variance. The combined standard uncertainty of the measurement result represents the estimated standard deviation of the result. It is obtained by combining the individual standard uncertainties of both Type A and Type B evaluation using the usual “root-sum-squares” (RSS) methods of combining standard deviations by taking the positive square root of the estimated variances. Expanded uncertainty is a measure of uncertainty that defines an interval about the measurement result within which the measured value is confidently believed to lie. It is obtained by multiplying the combined standard uncertainty by a coverage factor. For purpose of this document, a coverage factor two is used, which corresponds to confidence interval of about 95 %. The DASY uncertainty Budget is showed in Table 12.1. The judgment of conformity in the report is based on the measurement results excluding the measurement uncertainty. TEL : 886-3-327-3456 Page : 21 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A Uncertainty Ci Standard Probability Error Description Value Divisor (E) Uncertainty Distribution (±%) (E) Measurement System Probe Calibration 5.1 Normal 1 1 ± 5.1 % Axial Isotropy 4.7 Rectangular √3 1 ± 2.7 % Sensor Displacement 16.5 Rectangular √3 1 ± 9.5 % Boundary Effects 2.4 Rectangular √3 1 ± 1.4 % Phantom Boundary Effects 7.2 Rectangular √3 1 ± 4.1 % Linearity 4.7 Rectangular √3 1 ± 2.7 % Scaling with PMR Calibration 10.0 Rectangular √3 1 ± 5.77 % System Detection Limit 1.0 Rectangular √3 1 ± 0.6 % Readout Electronics 0.3 Normal 1 1 ± 0.3 % Response Time 0.8 Rectangular √3 1 ± 0.5 % Integration Time 2.6 Rectangular √3 1 ± 1.5 % RF Ambient Conditions 3.0 Rectangular √3 1 ± 1.7 % RF Reflections 12.0 Rectangular √3 1 ± 6.9 % Probe Positioner 1.2 Rectangular √3 1 ± 0.7 % Probe Positioning 4.7 Rectangular √3 1 ± 2.7 % Extrap. and Interpolation 1.0 Rectangular √3 1 ± 0.6 % Test Sample Related Device Positioning Vertical 4.7 Rectangular √3 1 ± 2.7 % Device Positioning Lateral 1.0 Rectangular √3 1 ± 0.6 % Device Holder and Phantom 2.4 Rectangular √3 1 ± 1.4 % Power Drift 5.0 Rectangular √3 1 ± 2.9 % Phantom and Setup Related Phantom Thickness 2.4 Rectangular √3 1 ± 1.4 % Combined Standard Uncertainty ± 16.30 % Coverage Factor for 95 % K=2 Expanded Std. Uncertainty on Power ± 32.6 % Expanded Std. Uncertainty on Field ± 16.3 % Table 12.1 Uncertainty Budget of HAC free field assessment Remark: Worst-Case uncertainty budget for HAC free field assessment according to ANSIC63.19 [1], [2]. The budget is valid for the frequency range 700 MHz - 3 GHz and represents a worst case analysis. TEL : 886-3-327-3456 Page : 22 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113

HAC RF EMISSIONS TEST REPORT Report No. : HA970203-03A 15. References [1] ANSI C63.19-2011, “American National Standard for Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids”, 27 May 2011. [2] FCC KDB 285076 D01v05, “Equipment Authorization Guidance for Hearing Aid Compatibility”, Sep 2017 [3] FCC KDB 285076 D02v03, “Guidance for performing T-Coil tests for air interfaces supporting voice over IP (e.g., LTE and WiFi) to support CMRS based telephone services”, Sep 2017 [4] FCC KDB 285076 D03v01, “Hearing aid compatibility frequently asked questions”, Sep 2017 [5] SPEAG DASY System Handbook TEL : 886-3-327-3456 Page : 23 of 23 FAX : 886-3-328-4978 Issued Date : Sep. 25, 2019 Form version: 181113


Document Created: 2019-10-27 00:17:40
Document Modified: 2019-10-27 00:17:40
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC