RF Test Report-WCDMA

FCC ID: 2ABZ2-A3000

Test Report

Download: PDF
FCCID_3202538

                                  TEST REPORT

                           No. I16N00975-WCDMA

                                                       for

                      OnePlus Technology(Shenzhen) Co., Ltd.

                                              Mobile Phone

                               Model Name: ONEPLUS A3000

                                       FCC ID: 2ABZ2-A3000

                                                      with

                                       Hardware Version: 28

                            Software Version: oxygen OS 3.5.1

                                     Issued Date: 2016-11-03
Note:
The test results in this test report relate only to the devices specified in this report. This report shall not be
reproduced except in full without the written approval of CTTL.
Test Laboratory:
FCC 2.948 Listed: No. 342690
CTTL,Telecommunication Technology Labs, Academy of Telecommunication Research, MIIT
No. 52, Huayuan North Road, Haidian District, Beijing, P. R. China 100191
Tel: +86(0)10-62304633-2512, Fax:+86(0)10-62304633-2504
Email: cttl_terminals@catr.cn, website: www.chinattl.com


                                                                 No. I16N00975-WCDMA
                                                                           Page2 of 18


REPORT HISTORY
Report Number               Revision             Description                Issue Date
I16N00975-WCDMA             Rev.0                1st edition                2016-11-03
NOTE: All the original values of this report quoted directly from No.I16N00359, except values of
RSE and ERP/EIRP.




                                                               ©Copyright. All rights reserved by CTTL.


                                                                                                       No. I16N00975-WCDMA
                                                                                                                 Page3 of 18


CONTENTS
1.      TEST LABORATORY ......................................................................................................................... 4

1.1.       TESTING LOCATION .................................................................................................................... 4

1.2.       TESTING ENVIRONMENT ........................................................................................................... 4

1.3.       PROJECT DATA .............................................................................................................................. 4

1.4.       SIGNATURE ..................................................................................................................................... 4

2.      CLIENT INFORMATION ................................................................................................................... 5

2.1.       APPLICANT INFORMATION ....................................................................................................... 5

2.2.       MANUFACTURER INFORMATION ............................................................................................ 5

3.      EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT (AE) ............................. 6

3.1.       ABOUT EUT ..................................................................................................................................... 6

3.2.       INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST .................................... 6

3.3.       INTERNAL IDENTIFICATION OF AE USED DURING THE TEST ....................................... 6

3.4.       GENERAL DESCRIPTION ............................................................................................................ 7

4.      REFERENCE DOCUMENTS ............................................................................................................. 8

4.1.       REFERENCE DOCUMENTS FOR TESTING ............................................................................. 8

5.      LABORATORY ENVIRONMENT ..................................................................................................... 9

6.      SUMMARY OF TEST RESULTS ..................................................................................................... 10

7.      TEST EQUIPMENTS UTILIZED .....................................................................................................11

ANNEX A: MEASUREMENT RESULTS................................................................................................ 12

     A.1 EMISSION LIMIT........................................................................................................................... 12




                                                                                                    ©Copyright. All rights reserved by CTTL.


                                                            No. I16N00975-WCDMA
                                                                      Page4 of 18



1. Test Laboratory
 1.1. Testing Location
 Company Name:              CTTL ShenZhen,Telecommunication Technology Labs, Academy of
                            Telecommunication Research, MIIT
 Address:                   TCL International E city No. 1001 Zhongshanyuan Road, Nanshan
                            District, Shenzhen, Guangdong, China
 Postal Code:               518048
 Telephone:                 +86(755)33322000
 Fax:                       +86(755)33322000


 1.2. Testing Environment
 Normal Temperature:        15-35℃
 Relative Humidity:         20-75%


 1.3. Project data
 Testing Start Date:        2016-08-31
 Testing End Date:          2016-11-03

 1.4. Signature




             Lai Minghua
     (Prepared this test report)




            Shen Shaoming
    (Reviewed this test report)




                Ma Zhiguo
   Deputy Director of the laboratory
    (Approved this test report)




                                                          ©Copyright. All rights reserved by CTTL.


                                                        No. I16N00975-WCDMA
                                                                  Page5 of 18



2. Client Information
 2.1. Applicant Information
 Company Name:       OnePlus Technology(Shenzhen) Co., Ltd.
 Address /Post:      18/F, Tower C, Tai Ran Building,No.8 Tai Ran Road, Shenzhen, China
 Contact Person:     Kevin Ke
 Contact Email       keyoujiang@oneplus.cn
 Telephone:          0755 61898696 EXT 7023
 Fax:                /


2.2. Manufacturer Information
 Company Name:       OnePlus Technology(Shenzhen) Co., Ltd.
 Address /Post:      18/F, Tower C, Tai Ran Building,No.8 Tai Ran Road, Shenzhen, China
 Contact Person:     Kevin Ke
 Contact Email       keyoujiang@oneplus.cn
 Telephone:          0755 61898696 EXT 7023
 Fax:                /




                                                      ©Copyright. All rights reserved by CTTL.


                                                                 No. I16N00975-WCDMA
                                                                           Page6 of 18



3. Equipment Under Test (EUT) and Ancillary Equipment (AE)
3.1. About EUT
  Description                Mobile Phone
  Model Name                 ONEPLUS A3000
  FCC ID                     2ABZ2-A3000
  Antenna                    Integrated
  Output power               24.02dBm maximum EIRP measured for Band IV
  Extreme vol. Limits        3.4VDC to 4.32VDC (nominal: 3.8VDC)
  Extreme temp. Tolerance -30°C to +50°C
Note: Components list, please refer to documents of the manufacturer; it is also included in the
original test record of CTTL, Telecommunication Technology Labs, Academy of
Telecommunication Research, MIIT
3.2. Internal Identification of EUT used during the test
EUT ID*     IMEI                     HW Version       SW Version           Sample Arrival Date
S01         860046030175725             28             oxygen OS 3.5.1      2016-08-31
S02         860046030175667             28             oxygen OS 3.5.1      2016-08-31
*EUT ID: is used to identify the test sample in the lab internally.
3.3. Internal Identification of AE used during the test
 AE ID*   Description
 AE1      Battery1
 AE2      Battery2
 AE3      Charger1
 AE4      Charger2
 AE5      Charger3
AE1
 Model                              BLP613
 Manufacturer                       Leung's Communication & Electric Products(Guangzhou)
                                    LTD.
 Capacitance                        3000mAh
AE2
 Model                              BLP633
 Manufacturer                       Dessary
 Capacitance                        3400mAh
AE3
 Model                              HK0504
 Manufacturer                       SHENZHEN HUNTKEY ELECTRIC CO., LTD
AE4
 Model                              DC0504A5
 Manufacturer                       SHENZHEN HUNTKEY ELECTRIC CO., LTD
AE5
 Model                              DC0504B5GB
 Manufacturer                       LITEON TECHNOLOGY CORPORATION

                                                               ©Copyright. All rights reserved by CTTL.


                                                                       No. I16N00975-WCDMA
                                                                                 Page7 of 18

*AE ID: is used to identify the test sample in the lab internally.
3.4. General Description
The Equipment Under Test (EUT) is a model HSDPA/HSUPA/UMTS Triband / GSM quadband /
LTE / CDMA mobile phone with integrated antenna. It consists of normal options: lithium battery,
charger. Manual and specifications of the EUT were provided to fulfil the test.




                                                                     ©Copyright. All rights reserved by CTTL.


                                                                 No. I16N00975-WCDMA
                                                                           Page8 of 18



4. Reference Documents

4.1. Reference Documents for testing
The following documents listed in this section are referred for testing.
 Reference             Title                                                              Version
      FCC Part 24      PERSONAL COMMUNICATIONS SERVICES                                   10-1-15
                                                                                          Edition
      FCC Part 22        PUBLIC MOBILE SERVICES                                           10-1-15
                                                                                          Edition
      FCC Part 2         FREQUENCY ALLOCATIONS AND RADIO TREATY                           10-1-15
                         MATTERS; GENERAL RULES AND REGULATIONS                           Edition
      FCC Part 27        WIRELESS COMMUNICATIONS SERVICES                                 10-1-15
                                                                                          Edition
    ANSI/TIA-603-C       Land Mobile FM or PM Communications Equipment                      2004
                         Measurement and Performance Standards
      ANSI C63.4         Methods of Measurement of Radio-Noise Emissions from                2009
                         Low-Voltage Electrical and Electronic Equipment in the
                         Range of 9 kHz to 40 GHz
   KDB 971168 D01        Measurement Guidance for Certification of Licensed Digital         v02r02
                         Transmitters




                                                               ©Copyright. All rights reserved by CTTL.


                                                             No. I16N00975-WCDMA
                                                                       Page9 of 18



5. LABORATORY ENVIRONMENT
Control room / conducted chamber did not exceed following limits along the EMC testing:
Temperature                                 Min. = 15 ℃, Max. = 35 ℃
Relative humidity                           Min. =20 %, Max. = 80 %
Shielding effectiveness                     > 110 dB
Electrical insulation                       > 2 M
Ground system resistance                  < 0.5 
Fully-anechoic chamber 2 (8.6 meters×6.1 meters×3.85 meters) did not exceed following limits
along the EMC testing:
Temperature                                 Min. = 15 ℃, Max. = 30 ℃
Relative humidity                           Min. = 35 %, Max. = 60 %
Shielding effectiveness                     > 110 dB
Electrical insulation                       > 2 M
Ground system resistance                    <1 
Site voltage standing-wave ratio (SVSWR)    Between 0 and 6 dB, from 1GHz to 18GHz
Uniformity of field strength                Between 0 and 6 dB, from 80 to 4000 MHz
Semi-anechoic chamber 2 / Fully-anechoic chamber 3 (10 meters×6.7 meters×6.15 meters)
did not exceed following limits along the EMC testing:
Temperature                                 Min. = 15 ℃, Max. = 30 ℃
Relative humidity                           Min. = 35 %, Max. = 60 %
Shielding effectiveness                     > 100 dB
Electrical insulation                       > 2 M
Ground system resistance                    < 0.5 
Normalised site attenuation (NSA)           < ±3.5 dB, 3 m distance
Site voltage standing-wave ratio (SVSWR)    Between 0 and 6 dB, from 1GHz to 18GHz
Uniformity of field strength                Between 0 and 6 dB, from 80 to 3000 MHz




                                                           ©Copyright. All rights reserved by CTTL.


                                             No. I16N00975-WCDMA
                                                      Page10 of 18



6. SUMMARY OF TEST RESULTS
 Items                    List       Clause in FCC rules               Verdict
  1      Emission Limit          2.1051/22.917/24.238/27.53                P




                                           ©Copyright. All rights reserved by CTTL.


                                                  No. I16N00975-WCDMA
                                                           Page11 of 18



7. Test Equipments Utilized
                                     SERIES                               CAL DUE
NO.     Description        TYPE                 MANUFACTURE
                                     NUMBER                                DATE
 1      Test Receiver       ESCI     100701            R&S                2017.08.09
 2     BiLog Antenna      VULB9163   9163 329     Schwarzbeck             2017.01.20
 3      Horn Antenna        3117     00066577     ETS-Lindgren            2017.04.01
       Universal Radio
 4     Communication      CMU200      114544           R&S                2017.09.09
           Tester
 5    Spectrum Analyser    FSP40     100378            R&S                2016.12.18




                                                ©Copyright. All rights reserved by CTTL.


                                                                 No. I16N00975-WCDMA
                                                                          Page12 of 18



ANNEX A: MEASUREMENT RESULTS
A.1   EMISSION LIMIT
A.1.1 Measurement Method
The measurements procedures in TIA-603C-2004 are used.
The spectrum was scanned from 30 MHz to the 10th harmonic of the highest frequency generated
within the equipment. The resolution bandwidth is set as outlined in Part 24.238, Part 22.917 and
Part 27.50.The spectrum was scanned with the mobile station transmitting at carrier frequencies
that pertain to low, mid and high channels of WCDMA Band II, WCDMA Band V and WCDMA
Band IV.

The procedure of radiated spurious emissions is as follows:
1. EUT was placed on a 1.5 meter high non-conductive stand at a 3 meter test distance from the
   receive antenna. A receiving antenna was placed on the antenna mast 3 meters from the EUT
   for emission measurements. The height of receiving antenna is 1.5m. The test setup refers to
   figure below. Detected emissions were maximized at each frequency by rotating the EUT
   through 360° and adjusting the receiving antenna polarization. The radiated emission
   measurements of all non-harmonic and harmonics of the transmit frequency through the 10th
   harmonic were measured with peak detector.




2. The EUT is then put into continuously transmitting mode at its maximum power level during
   the test. And the maximum value of the receiver should be recorded as (Pr).
3. The EUT shall be replaced by a substitution antenna. The test setup refers to figure below.




   In the chamber, an substitution antenna for the frequency band of interest is placed at the
   reference point of the chamber. An RF Signal source for the frequency band of interest is

                                                               ©Copyright. All rights reserved by CTTL.


                                                                 No. I16N00975-WCDMA
                                                                          Page13 of 18

   connected to the substitution antenna with a cable that has been constructed to not interfere
   with the radiation pattern of the antenna. A power (PMea) is applied to the input of the
   substitution antenna, and adjust the level of the signal generator output until the value of the
   receiver reach the previously recorded (Pr). The power of signal source (PMea) is recorded. The
   test should be performed by rotating the test item and adjusting the receiving antenna
   polarization.
4. The Path loss (Ppl) between the Signal Source with the Substitution Antenna and the
   Substitution Antenna Gain (Ga) should be recorded after test.
   A amplifier should be connected in for the test.
   The Path loss (Ppl) is the summation of the cable loss and the gain of the amplifier.
   The measurement results are obtained as described below:
   Power(EIRP)=PMea - Ppl - Ga
5. This value is EIRP since the measurement is calibrated using an antenna of known gain (2.15
   dBi) and known input power.
6. ERP can be calculated from EIRP by subtracting the gain of the dipole, ERP = EIRP -2.15dBi.




                                                               ©Copyright. All rights reserved by CTTL.


                                                                   No. I16N00975-WCDMA
                                                                            Page14 of 18

A.1.2 Measurement Limit
Part 24.238 , Part 22.917 and Part 27.50 specify that the power of any emission outside of the
authorized operating frequency ranges must be attenuated below the transmitting power (P) by a
factor of at least 43 + 10 log(P) dB.
The specification that emissions shall be attenuated below the transmitter power (P) by at least 43
+ 10 log (P) dB, translates in the relevant power range (1 to 0.001 W) to -13 dBm. At 1 W the
specified minimum attenuation becomes 43 dB and relative to a 30 dBm (1 W) carrier becomes a
limit of -13 dBm. At 0.001 W (0 dBm) the minimum attenuation is 13 dB, which again yields a limit
of -13 dBm. In this way a translation of the specification from relative to absolute terms is carried
out.

A.1.3 Measurement Results
Radiated emissions measurements were made only at the upper, middle, and lower carrier
frequencies of WCDMA Band II (1852.4 MHz, 1880.0MHz and 1907.6MHz), WCDMA Band
V(826.4MHz, 836.6MHz and 846.6MHz) and WCDMA Band IV (1712.4MHz, 1740.0MHz and
1752.6MHz). It was decided that measurements at these three carrier frequencies would be
sufficient to demonstrate compliance with emissions limits because it was seen that all the
significant spurs occur well outside the band and no radiation was seen from a carrier in one block
of the WCDMA Band II,WCDMA Band V and WCDMA Band IV into any of the other blocks. The
equipment must still, however, meet emissions requirements with the carrier at all frequencies
over which it is capable of operating and it is the manufacturer's responsibility to verify this.




                                                                 ©Copyright. All rights reserved by CTTL.


                                                      No. I16N00975-WCDMA
                                                               Page15 of 18

A.1.4 Measurement Results Table
    Frequency              Channel          Frequency Range               Result
                             Low              30MHz-10GHz                   Pass
  WCDMA Band V              Middle            30MHz-10GHz                   Pass
                             High             30MHz-10GHz                   Pass
                             Low              30MHz-20GHz                   Pass
  WCDMA Band II             Middle            30MHz-20GHz                   Pass
                             High             30MHz-20GHz                   Pass
                             Low              30MHz-20GHz                   Pass
 WCDMA Band IV              Middle            30MHz-20GHz                   Pass
                             High             30MHz-20GHz                   Pass


A.1.5 Sweep Table
     Working          Subrange
                                      RBW         VBW         Sweep time (s)
    Frequency          (GHz)
                       0.03~1        100KHz      300KHz              10
                         1-2          1 MHz       3 MHz               2
 WCDMA Band V            2~5          1 MHz       3 MHz               3
                         5~8          1 MHz       3 MHz               3
                        8~10          1 MHz       3 MHz               3
                       0.03~1        100KHz      300KHz              10
                         1-2          1 MHz       3 MHz               2
                         2~5          1 MHz       3 MHz               3
                         5~8          1 MHz       3 MHz               3
 WCDMA Band II
                        8~11          1 MHz       3 MHz               3
                       11~14          1 MHz       3 MHz               3
                       14~18          1 MHz       3 MHz               3
                       18~20          1 MHz       3 MHz               2
                       0.03~1        100KHz      300KHz              10
                         1-2          1 MHz       3 MHz               2
                         2~5          1 MHz       3 MHz               3
                         5~8          1 MHz       3 MHz               3
 WCDMA Band IV
                        8~11          1 MHz       3 MHz               3
                       11~14          1 MHz       3 MHz               3
                       14~18          1 MHz       3 MHz               3
                       18~20          1 MHz       3 MHz               3




                                                    ©Copyright. All rights reserved by CTTL.


                                                              No. I16N00975-WCDMA
                                                                       Page16 of 18


   WCDMA BAND II Mode Channel 9262/1852.4MHz(QPSK)
                             Antenna      Peak      Limit
Frequency(MHz)   PMea(dBm)                                   Polarization
                              Gain     EIRP(dBm)   (dBm)
  17205.94        -46.78     -13.11     -36.57     -13.00          H
  17303.72        -47.67     -13.45     -37.12     -13.00          V
  17435.63        -46.47     -13.45     -35.92     -13.00          H
  17557.69        -47.06     -13.66     -36.40     -13.00          H
  17822.81        -45.95     -13.66     -35.39     -13.00          H
  17925.84        -45.78     -13.71     -35.17     -13.00          H

   WCDMA BAND II Mode Channel 9400/1880MHz(QPSK)
                             Antenna      Peak      Limit
Frequency(MHz)   PMea(dBm)                                   Polarization
                              Gain     EIRP(dBm)   (dBm)
   17202          -46.41     -13.11     -36.20     -13.00          H
  17274.84        -46.04     -13.11     -35.83     -13.00          H
  17413.97        -46.17     -13.45     -35.62     -13.00          H
  17608.88        -46.25     -13.66     -35.59     -13.00          H
  17779.5         -45.64     -13.71     -34.93     -13.00          H
  17928.47        -44.16     -13.71     -33.55     -13.00          H

   WCDMA BAND II Mode Channel 9538/1907.6MHz(QPSK)
                             Antenna      Peak      Limit
Frequency(MHz)   PMea(dBm)                                   Polarization
                              Gain     EIRP(dBm)   (dBm)
  16794.47        -46.92     -13.11     -36.71     -13.00          H
  17354.25        -47.15     -13.45     -36.60     -13.00          H
   17412          -46.65     -13.45     -36.10     -13.00          H
  17606.25        -46.89     -13.66     -36.23     -13.00          H
  17778.19        -46.08     -13.71     -35.37     -13.00          H
  17935.69        -46.01     -13.71     -35.40     -13.00          H




                                                            ©Copyright. All rights reserved by CTTL.


                                                          No. I16N00975-WCDMA
                                                                   Page17 of 18


WCDMA BAND V Mode Channel 4132/826.4MHz(QPSK)
                              Antenna   Correction     Peak       Limit
 Frequency(MHz)   PMea(dBm)                                                    Polarization
                               Gain       (dB)       ERP(dBm)    (dBm)
     8564.5        -55.98       1.9      -13.66       -44.22       -13.00            H
      9213         -56.46       2.1      -13.78       -44.78       -13.00            V
     9401.5        -56.79       2.1      -13.79       -45.10       -13.00            V
     9745.5         -56.2       2.2      -13.79       -44.61       -13.00            H
      9844         -56.72       2.2      -13.79       -45.13       -13.00            V
      9979         -56.74       2.2      -13.79       -45.15       -13.00            H

WCDMA BAND V Mode Channel 4183/836.6MHz(QPSK)
                              Antenna   Correction     Peak       Limit
 Frequency(MHz)   PMea(dBm)                                                    Polarization
                               Gain       (dB)       ERP(dBm)    (dBm)
     7023.5        -56.75       1.8       -13.1       -45.45       -13.00            V
      7354         -56.53       1.8       -13.1       -45.23       -13.00            V
     7626.5        -56.89       1.8       -13.1       -45.59       -13.00            H
     9149.5         -57.3       2.0      -13.78       -45.52       -13.00            V
      9259         -56.83       2.1      -13.78       -45.15       -13.00            V
     9354.5        -56.68       2.1      -13.79       -44.99       -13.00            V

WCDMA BAND V Mode Channel 4233/846.6MHz(QPSK)
                              Antenna   Correction     Peak       Limit
 Frequency(MHz)   PMea(dBm)                                                    Polarization
                               Gain       (dB)       ERP(dBm)    (dBm)
      6692         -55.88       1.7      -13.10       -44.48       -13.00            H
      8053         -56.94       1.8      -13.46       -45.28       -13.00            H
     8637.5        -56.96       1.9      -13.66        -45.2       -13.00            H
      9117         -56.96       2.0      -13.78       -45.18       -13.00            V
      9255         -56.74       2.1      -13.78       -45.06       -13.00            H
      9395         -56.42       2.1      -13.79       -44.73       -13.00            H




                                                        ©Copyright. All rights reserved by CTTL.


                                                         No. I16N00975-WCDMA
                                                                  Page18 of 18


WCDMA BAND IV Mode Channel 1312/1712.4MHz(QPSK)
                                   Antenna      Peak      Limit
      Frequency(MHz)   PMea(dBm)                                       Polarization
                                    Gain     EIRP(dBm)   (dBm)
         17205.94       -46.78     -13.11     -36.57       -13.00           H
         17303.72       -47.67     -13.45     -37.12       -13.00           V
         17435.63       -46.47     -13.45     -35.92       -13.00           H
         17557.69       -47.06     -13.66     -36.40       -13.00           H
         17822.81       -45.95     -13.66     -35.39       -13.00           H
         17925.84       -45.78     -13.71     -35.17       -13.00           H

WCDMA BAND IV Mode Channel 1450/1740.0MHz(QPSK)
                                   Antenna      Peak      Limit
      Frequency(MHz)   PMea(dBm)                                       Polarization
                                    Gain     EIRP(dBm)   (dBm)
          17202         -46.41     -13.11     -36.20       -13.00           H
         17274.84       -46.04     -13.11     -35.83       -13.00           H
         17413.97       -46.17     -13.45     -35.62       -13.00           H
         17608.88       -46.25     -13.66     -35.59       -13.00           H
         17779.5        -45.64     -13.71     -34.93       -13.00           H
         17928.47       -44.16     -13.71     -33.55       -13.00           H

WCDMA BAND IV Mode Channel 1513/1752.6MHz(QPSK)
                                   Antenna      Peak      Limit
      Frequency(MHz)   PMea(dBm)                                       Polarization
                                    Gain     EIRP(dBm)   (dBm)
         16794.47       -46.92     -13.11     -36.71       -13.00           H
         17354.25       -47.15     -13.45     -36.60       -13.00           H
          17412         -46.65     -13.45     -36.10       -13.00           H
         17606.25       -46.89     -13.66     -36.23       -13.00           H
         17778.19       -46.08     -13.71     -35.37       -13.00           H
         17935.69       -46.01     -13.71     -35.40       -13.00           H




                                 ***END OF REPORT***




                                                       ©Copyright. All rights reserved by CTTL.



Document Created: 2019-07-13 15:14:23
Document Modified: 2019-07-13 15:14:23

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC