Users Manual

FCC ID: 2ABYNX1C

Users Manual

Download: PDF
FCCID_2733286

               Contents
        15    Foreword
        15    For Your Safety
        17    Names of Parts
               Body
               LCD Panel Accessories
        19    Battery Installing
               Batteries
               Low Battery Level Indication
        20    Using the Flash Trigger
               As a Wireless Studio Flash Trigger
               As a Wireless Speedlite Trigger
               As a Wired Shutter Release
               As a Wireless Studio Flash Trigger or Speedlite
               Trigger with PC Sync Socket
        21    Setting the Transmitter
               Power Switch
               Power Switch of AF Assist Beam Channel
               Settings Mode Settings Current Group Settings
               Group Settings Test Flash
               Setting GR Grouping Mode Automatically Enter
        Power Saving Mode C.Fn: Setting Custom Functions
        Wireless Shutter Release Mode Setting the Camera 25
              Setting the Receiver
               Channel Settings Group Settings
               Automatically Enter Power Saving Mode
        27    Attentions
        27    Caring for Flash Trigger
        28    Technical Data




-13 -


             Foreword                                                                          For Your Safety
Thanks for your purchase of this X1C TTL wireless flash trigger.                                        A Do not disassemble or modify
This TTL wireless flash trigger can be used with a transmitter and one or more receivers for                Failure to observe this precaution could result in electric shock or product malfunction.
studio flash, speedlite, and camera shutter. Featuring multi-channel triggering, stable signal              Should the product break open as the result of a fall or other accident, remove the
transmission, and sensitive reaction, it gives photographers unparalleled flexibility and control           batteries and take the product to an authorized maintenance center for inspection.
over their strobist setups. The flash trigger applies to hotshoe-mounted Canon EOS series               A Keep dry
cameras, as well as the cameras which have PC sync sockets.                                                 Do not handle with wet hands or immerse in or expose to water or rain. Failure to
With X1C wireless flash trigger, high speed synchronization is available for most of camera                 observe this precaution could result in fire or electric shock.
flashes in the market which support E-TTL II. The max flash synchronization speed is up to              A Do not use in the presence of flammable gas
1/8000s *.                                                                                                  Failure to observe this precaution could result in explosion or fire.
                                                                                                        A Keep out of reach of children
*: 1/8000s is achievable when the camera has a max camera shutter speed of 1/8000s.                         This device contains small parts which may pose a choking hazard. Consult a physician
1/8000s is not achievable because some models of Canon EOS cameras have a max camera                        immediately if a child swallows any part of this device.
shutter speed of only 1/4000s.                                                                          A Turn off the transceiver immediately in the event of malfunction
                                                                                                            Should smoke or an unusual smell comes from this device, remove the batteries
                                                                                                            immediately in case of burning and take the device to an authorized maintenance center
                                                                                                            for inspection. Injuries could occur if it is further used.
                                                                                                        A Do not expose to high temperature
                                                                                                            Do not leave the device in a closed vehicle in the sun or in other areas subject to
                                                                                                            extremely high temperature. Failure to observe this precaution could result in fire or
                                                                                                            damage to the casing or internal parts.
                                                                                                        A Observe precautions when handling batteries
                                                                                                            Batteries may leak or explode if improperly handled. Observe the following precautions
                                                                                                            when handling batteries for use in this device:
                                                                                                             • Use only batteries listed in this manual. Do not use old and new batteries or batteries
                                                                                                                of different types at the same time.
             For Your Safety                                                                                 • Readandfollowallwarningsandinstructionsprovidedbythemanufacturer.
                                                                                                             • Batteries cannot be short-circuited or disassembled.
To prevent damage to your product or injury to you or to others, read the following safety                   • Do not put batteries into a fire or apply direct heat to them.
precautions in their entirety before using this device. Keep these safety instructions where all             • Do not attempt to insert batteries upside down or backwards.
those who use this device will read them.                                                                    • Batteries are prone to leakage when fully discharged. To avoid damage to the
Failure to observe the precautions listed in this section could result in damage to the product.                product, be sure to remove batteries when the product is not used for a long time or
The following icon indicates warnings that should be read before using this device in case of                   when batteries run out of charge.
possible damage or injury.                                                                                   • Should liquid from the batteries come into contact with skin or clothing, rinse
                                                                                                                immediately with fresh water.




                                              -15 -                                                                                                  -16 -


             Names of Parts                                                                                   Names of Parts

    • Body
      Transmitter                                                   TEST Trigger Button                Receiver
                                                                                                                                                                   TEST Trigger Button
                                                                    --Half Press --Fully Press

         Battery
     Compartment
                                                                    AF Assist Beam Switch                   Battery
                                                                    --ON(AF Assist Beam outputs)        Compartment
                                                                    --OFF(AF Assist Beam do not
                                                                    output)
   Micro USB Port
                                                                    Power Switch --ON (Power
                                                                    On)                                Micro USB Port                                              Power     Switch
  PC Sync Socket                                                    --OFF (Power Off)                                                                              --ON (Power On)
                                                                                                       2.5mm Shutter                                               --OFF (Power Off)
                                                                                                         Release Port
Hot Shoe Speedlite
       Connection                                                   Status Indicator Lamp          Hot Shoe Speedlite                                              Status Indicator Lamp
                                                                    --LED Red Color Lamp                  Connection                                               --LED Red Color Lamp



                                                                    CH Channel Setting Button
       LCD Panel                                                                                                                                                   CH Channel Setting Button
                                                                    GR Group Setting Button               LCD Panel
                                                                                                                                                                   GR Group Setting Button
                                                                    Select Dial

                                                                    MODE Mode Selection Button
 Hot Shoe Camera
       Connection



       LCD Panel                                                                                       LCD Panel
                                                                                                                              C

                          丨E

                                                                G




                           CB              A           I                                                                            B          A
  (A) Output Settings per Group in the M Mode; FEC Settings per Group in the TTL Mode              (A) Group Setting (B) Channel Setting   (C) Low Battery Indicator
  (B) Mode Settings (C) Group (D) Currently Selected Group (E) Channel Settings
  (F) GR Grouping Icon (G) Synchronization Delay Setting Icon (H) Low Battery Indicator (I)
  Single Contact Icon

                                            -17 -                                                                                          -18 -


        Names of Parts                                                                                     Using the Flash Trigger

• Accessories                                                                                  The flash trigger features the following functions:

 I.Remote Cable(C1, C3)                2.Sync                     3.Sync Adapter               1. As a Wireless Studio Flash Trigger
 Cable                                                                                            1.1 Mount the transmitter on camera hotshoe and turn it
                                                                                                      on before turning on the camera.
                                                                                                  1.2 Connect the receiver to studio flash by Sync Cable
                                                                                                      (one end in 2.5mm Shutter Release Port of the
                                                                                                      receiver, the other end in sync port of studio flash)
                                                                                                      before turning on the studio flash.
                                                                                                  1.3 Set the transmitter and the receiver to the same
                                                                                                      channel.
         Battery                                                                                  1.4 Press the camera shutter button, and the studio flash
                                                                                                      will be triggered simultaneously. Status Indicator
                                                                                                      Lamp of both transmitter and receiver units turn red.
 • Installing Batteries
 As shown in the illustration, slide the battery compartment lid of the transmitter and        2. As a Wireless Speedlite Trigger
 receiver and insert two AA batteries (sold separately) separately.                               2.1 Mount the transmitter on camera hotshoe and turn it
 • Low Battery Indication                                                                             on before turning on the camera.
 When the battery power (2 AA batteries <2.0V) gets low, Status Indicator Lamp blinks             2.2 Mount the speedlite to Hot Shoe Speedlite
 quickly (blink cycle=0.5s). Please replace new batteries, as low power leads to no flash or          Connection of receiver unit. Set the speedlite to M
 flash missing in case of long distance.                                                              mode.
                                                                                                  2.3 Set the transmitter and the receiver units to the same
                                                                                                      channel.
                                                                                                  2.4 Press the camera shutter button, and the speedlite
                                                                                                      will be triggered simultaneously. Status Indicator
                                                                                                      Lamp of both transmitter and receiver units turn red.

                                                                                               3. As a Wired Shutter Release
                                                                                                  3.1 Connect the receiver and the camera by Remote
                                                                                                      Cable (one end in receiver's Shutter Release Port,
                                                                                                      the other end in camera’s shutter port) before turning
                                                                                                      on the camera.
                                                                                                  3.2 Half press the <TEST> Trigger Button to focus.
                                                                                                      When fully press the <TEST> Trigger Button to
                                                                                                      shoot, the Status Indicator Lamp will turn red until
                                                                                                      releasing the button.




                                          -19 -                                                                                              -20 -


             Using the Flash Trigger                                                                         Setting the Transmitter
 4. As a Wireless Studio Flash Trigger or Speedlite                                            • Mode Setting
  Trigger with PC Sync Socket                                                                  1.   Short press the <MODE> Button, and the
  4.1 The connection method of the receiver can be                                                  mode of the current group will change.
      found in As a Wireless Studio Flash Trigger and                                          2.   To NON-GR grouping mode, all the groups’
      As a Wireless Speedlite Trigger section.                                                      modes will be changed simultaneously by the
  4.2 The transmitter will control the flash on the                                                 order of TTL/M, in accordance with Ratio flash
      receiver end to fire via using PC Sync Socket as                                              mode. To GR grouping mode, only the current
      input by default.                                                                             group’s mode will be changed by the order of
  4.3 Press the camera shutter and use the PC Sync                                                  TTL/M/--.
      Socket’s signal to control the flash.
  4.4 PC Sync Socket can also be set as output. Long                                           • Current Group Settings
      press the <CH> Button of the transmitter until                                           1.   Short press the <GR> Button to set the
      <Fn> is displayed on the panel. Then, set the                                                 current group.
      value of Fn 03 to 1, and the PC Sync Socket is                                           2.   The current group settings will blink and turn
      under output mode.                                                                            the Select Dial to change the settings.
                                                                                               3.   When the current group is in the M mode, the
                                                                                                    power output value is changeable from 1/1
            Setting the Transmitter                                                                 full power to 1/128th power in 0.3 stop
                                                                                                    increments. When the current group is in the
• Power Switch                                                                                      TTL mode, the FEC amount is changeable
Slide the Power Switch to ON, and the device is on and Status Indicator Lamp will not blink.        from -3 to 3 in 0.3 stop increments. When the
    Note: In order to avoid power consumption, turn off the transmitter when not in use.
                                                                                                    current group is in the -- mode (flash off), the
                                                                                                    amounts will not change.
• Power Switch of AF Assist Beam
   Slide the power switch to ON, and the AF lighting is allowed to output.                     4.   Short press the <GR> Button again to confirm
                                                                                                    the setting.
• Channel Setting
   1. Short press the <CH> Button until the                                                    • Group Settings
      channel amount blinks.                                                                   1.   Long press the <GR> Button to set all the
   2. Turn the Select Dial to choose the                                                            groups that in the same modes
      appropriate channel. Press the <CH>                                                           simultaneously.
      Button again to confirm the setting.                                                     2.   The settings of the groups which are in the same mode with the current group will blink.
   3. This flash trigger contains 32 channels                                                       Turn the Select Dial to change the settings.
      which can be changed from 1 to 32. Set                                                   3.   If the current group is in the M mode, all the other groups which are in the M mode will
      the transmitter and the receiver to the                                                       change their power output value simultaneously. The power output value is changeable
      same channel before usage.                                                                    from 1/1 full power to 1/128th power in 0.3 stop increments, until one of the group’s setting
                                                                                                    turns to the maximum(1/1) or the minimum(1/128). If the current




                                             -21 - - 22 -


           Setting the Transmitter                                                                           Setting the Transmitter
     group is in the TTL mode, all the other groups which are in the M mode will change       • Automatically Enter Power Saving Mode
     their FEC amount simultaneously. The FEC amount is changeable from -3 to 3 in 0.3          1. The flash trigger will go into standby mode after the transmitter enter sleep mode, and
     stop increments, until one of the group’s setting turns to the maximum(3) or the              the displays on the LCD panel will disappear.
     minimum(-3). If the current group is in the -- mode (flash off), the amounts will not      2. Press any of the button (<TEST> fully pressed/<CH>/<GR>/<MODE>) can wake up
     change.                                                                                       the flash trigger. If the transmitter is attached to the CANON EOS camera, half press
 4. Short press the <GR> Button again to confirm the setting.                                      the shutter can also wake up the system.

• Test Flash                                                                                 C.Fn: Setting Custom Functions
1. Press the <TEST> Trigger Button to see the                                                The following table lists the available and unavailable custom functions of this flash. The
      whether flash will fire normally or not.                                               icon“V"indicates the flash custom function is supported but “0”indicates the custom function
2. Fully press the <TEST> Trigger Button, and the                                            is not supported.
      Status Indicator Lamp turns red and the flash
                                                                                             Custom          Functions             Setting Signs    Settings and Description                                   Application
      on the receive end can be triggered.
3. Use the transmitter to control camera to focus                                            Functions No.

      or shoot, and the transmitter is connecting to                                                         Synchronization                        OFF
                                                                                                                                        0
      the camera (do not connect to the flash) now.                                          C.Fn-00         delay setting            1~100
                                                                                                                                                    Master flash synchronization delay N*100 us                     V
4. In the standby mode, press the TEST Button                                                                                                       (synchronization delay icon           is displayed.)
      can wake up the receiver.                                                                              Single contact
                                                                                                                                        0           OFF
5. The settings on the transmitter end will                                                                  mode
                                                                                             C.Fn-01                                                                                                                V
      synchronize to the receiver end at the same                                                                                       1           ON (The single contact mode set icon [^j] is displayed.)
      time.
                                                                                                                                        0           Do not change the zoom value.

                                                                                                                                        AU          Changing with camera's zoom value.
                                                                                             C.Fn-02         Zoom setting                                                                                           V
                                                                                                                               20,24,28,35,50,70,   Zoom(20/24/28/35/50/70/80/105/135/
• Setting GR Grouping Mode
                                                                                                                               80,105,135,135+      135+mm)
  1. Press the <MODE> Mode Button until Gr                                                                   PC sync socket             0           PC sync socket connects with camera

     icon is displayed, which shows that GR                                                                                                         PC sync socket connects with flash
                                                                                             C.Fn-03         connects with                                                                                          V
                                                                                                                                        1
     grouping mode has been set.
                                                                                                             camera/flash
  2. To cancel GR grouping mode, press the
                                                                                             1. Press the <CH> Button for 2 seconds or longer until <Fn> is displayed.
    <MODE> Button again until the Gr icon                                                    2. Select the custom function No.
    disappeared.                                                                                 * Turn the Select Dial to choose the Custom Function No.
    Note: GR mode can only be used normally when
                                                                                             3. Change the Setting.
          attaching to the CANON EOS cameras that
                                                                                                 * Press the <GR> Button until the custom function No. blinks.
           issued after 2012. If the camera model do
           not support GR grouping flash mode, NON                                               * Turn the Select Dial to set the desired number. Pressing <GR> button will confirm the
           GR mode will be changed automatically.                                                  settings.
           And the GR icon on the LCD panel will                                                 * Press <MODE> button to exit the C.Fn settings.
           disappear.



                                             -23 -                                                                                                  -24 -


             Setting the Transmitter                                                                                Setting the Receiver
• Wireless Shutter Release Mode                                                                         • Group Settings
Half press the <TEST> Trigger Button to focus. Fully press the <TEST> Trigger Button, and               1.   Short press the <GR> Button and the group
the Status Indicator Lamp turns red. Now camera is ready to shoot. When releasing the                         amount will increase a step each time.
button, the Status Indicator Lamp turns off.                                                            2.   Long press the <GR> Button will enter
                                                                                                              quicker adjustment mode. The group
• Setting the Camera                                                                                          amount will increase fast in this mode.
Use the External Flash Function on the camera to do the setting.
                                                                                                        3.   Release the <GR> Button and the current
Note: 1. GR mode can only be used normally when attaching to the CANON EOS cameras that issued
          after 2012. If the camera model do not support GR grouping flash mode,                              group amount is confirmed.
          NON GR mode will be changed automatically.                                                    4.   The group amount will increase from A to E.
                                                                                                              When the current group is E, press the <GR>
        2. In the NON-GR mode, Ration Off is steadily set in the TTL mode while A:B C is steadily set         Button again and the group A will be
          in the M mode.                                                                                      displayed on the panel.
                                                                                                        Note: If the transmitter in the same channel is set to NON-GR grouping mode, the effective groups of
                                                                                                                  the receiver will change from A to C. Make sure the receiver 's group is set to A/B/C.
                                                                                                                  If the transmitter in the same channel is set to GR grouping mode, the effective groups of the
                                                                                                                  receiver will change from A to E.


            Setting the Receiver                                                                        • Automatically Enter Power Saving Mode
                                                                                                        1.   The system will go into standby mode after the transmitter goes into standby mode. And
• Channel Setting                                                                                             the displays on the LCD panel disappear now.
1.   Short press the <CH> Button and the
                                                                                                        2.   To wake up the system, press the <TEST> Button or the <GR> Button. Fully press the
      channel amount will increase a step each
                                                                                                              <TEST> Trigger Button of the transmitter can also wake up the receiver’s system. If the
      time.
                                                                                                              transmitter is attached to the CANON EOS camera, half press the camera shutter can
2.   Long press the <CH> Button will enter
                                                                                                              also wake up the system.
      quicker adjustment mode. The channel
      amount will increase fast in this mode.
3.   Release the <CH> Button and the current
      channel amount is confirmed.
4.   The channel amount will increase from 1 to
      32. When the current channel is 32, press
      the <CH> Button again and the channel 1
      will be displayed on the panel.




                                               -25 -                                                                                                     - 26 -


            Attentions                                                                                               Technical Data
                                                                                                    Model                              X1C
1. Unable to trigger flash or camera shutter. Make sure batteries are installed correctly and
    Power Switch is turned on. Check if the transmitter and the receiver are set to the same        Type                               For Canon
                                                                                                    Compatible Cameras
    channel, if the hotshoe mount or connection cable is well connected, or if the flash triggers                                      Canon EOS cameras (E-TTL II autoflash)

    are set to the correct mode.                                                                                                       Support for the cameras that have PC sync socket.

2. Camera shoots but does not focus. Check if the focus mode of the camera or lens is set to        Builted-in remote system           2.4G Wireless Transmission

    MF. If so, set it to AF.                                                                        Modulation mode                    MSK
3. Signal disturbance or shooting interference. Change a different channel on the device.           Power supply                       2*AA batteries
4. Operating distance limited or flash missing. Check if batteries are exhausted. If so, change     Exposure Control
    them.                                                                                           Manual flash                       Yes
5. No             is displayed on the camera viewfinder, though the camera is mounted on            TTL autoflash                      E-TTL II

    the transmitter and the power switch is turned on. This is resulted from unusual working of     TTL Control
    the transmitter. Check and make sure the flash trigger is well connected to the camera          High-speed sync                    Yes
    through Hot Shoe Camera Connection, then power the Transmitter on again.                        Flash exposure compensation        Yes, ±3 stops in 1/3 stop increments

                                                                                                    Flash exposure lock                Yes

                                                                                                    Focus assist                       Manual open

                                                                                                    Second curtain sync                No

                                                                                                    Modeling flash                     Yes, fired with camera's depth-of-field preview button

            Caring for Flash Trigger                                                                Wireless Flash
                                                                                                    Wireless function
                                                                                                                                       In TTL mode, Ratio Off

 • Avoid sudden drops. The device may fail to work after strong shocks, impacts, or excess                                             In M mode, Flash Ratio (A:B C)

   stress.                                                                                                                             Support for GR group flash, A~E group can set their flash mode separately.
                                                                                                    Controllable slave group
 • Keep dry. The product isn't water-proof. Malfunction, rust, and corrosion may occur and                                             In the GR grouping mode, 5 (A/B/C/D/E)

   go beyond repair if soaked in water or exposed to high humidity.                                                                    In the Ratio grouping mode, 3 (A/B/C)

 • Avoid sudden temperature changes. Condensation happens if sudden temperature                     Transmission range(approx.)        >100m
   changes such as the circumstance when taking the transceiver out of a building with              Channel                            32

   higher temperature to outside in winter. Please put the transceiver in a handbag or plastic      Others
   bag beforehand.                                                                                  Synchronization delay set          Yes (0~10ms, use 100us as the unit)
 • Keep away from strong magnetic field. The strong static or magnetic field produced by            Wireless shutter release           Receiver can control camera shooting through 2.5mm sync port
   devices such as radio transmitters leads to malfunction.                                         ZOOM setting                       Adjust the flash's focal length through the transmitter

                                                                                                    LCD panel                          Wide LCD panel, backlight on/off
                                                                                                    Output interface
                                                                                                                                       Transmitter: use a PC cord to input and output

                                                                                                                                       Receiver: use a 2.5mm sync cord to output

                                                                                                    Firmware upgrade                   Use the Micro USB port to upgrade
                                                                                                    Memory function
                                                                                                                                       Settings will be stored 2 seconds after last operation and
                                                                                                                                       recover after a restart

                                                                                                    Dimension/Weight for Transmitter   72x75x52(mm)/100g

                                                                                                    Dimension/Weight for Receiver      70x65x47(mm)/70g


                                              -27 -                                                                                                        -28 -


FCC warning
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.


This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.


FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.


This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection


against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio


or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.


—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.


—Consult the dealer or an experienced radio/TV technician for help




                                             -27 -                                                                                                         -29 -



Document Created: 2015-08-28 15:55:12
Document Modified: 2015-08-28 15:55:12

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC