User Manual_Part II_R1

FCC ID: 2ABYNV350

Users Manual

Download: PDF
FCCID_3935594

Slave Unit Setting 5. TTL: Fully Automatic Wireless Flash Shooting MODE ZOOM SYNC SLAVE 1 Long Press the <SYNC> button for 2 seconds so that Autoflash Shooting with One Slave Unit SET < > is blinking. Turn the Select Dial until the < > is 1 Master Unit Setting ● Attach a V350S camera flash on the camera and set it displayed on the LCD panel, as the master unit. (Page 40) which means the slave unit. ● M/A/B/C can be set as TTL mode independently. 2. Setting Master Unit’s Flash Mode 2 Slave Unit Setting ● Set the V350S that to be MODE ZOOM SYNC SLAVE 1 Press the <SLAVE> Button to choose the group from M/A/B/C. Then, press the controlled as the wireless slave unit. (Page 41) SET < MODE > Button so that the ● The slave unit can be set master unit can work in OFF / as A/B/C. TTL / M flash mode. Choose one of them as the flash mode of master unit. 3 Check the communication channel ● If the master unit and MODE ZOOM SYNC SLAVE slave unit(s) are set to a different channel, set them SET to the same channel. 2 Press the <MODE> Button for 2 seconds to switch to Multi (Page 41) mode. 4 Position the camera and flashes ● Position the camera and 3. Setting the Communication Channel flashes as the picture If there are other wireless flash systems nearby, you can change the shows. (Page 43) channel IDs to prevent signal interference. The channel IDs of the master unit and the slave unit(s) must be set to the same. MODE ZOOM SYNC SLAVE 5 Check the flash operation ● Press the master unit’s MODE ZOOM SYNC SLAVE 1 Long press the <SLAVE> Button for 2 seconds until the channel IDs is blinking. Turn SET Test Button< >. ● Then, the slave unit will SET the Select Dial to choose a fire. If not, adjust the slave channel ID from 1 to 16. unit’s angle toward the master unit and distance from the master unit. SET 2 Press the <SET> button to confirm. The slave unit might be out of order or fire an unwanted flash due to the nearby wifi routers or other 2.4G equipments. If in this case, please adjust the flash’s channel or turn off the 2.4G equipments. 6. M: Wireless Flash Shooting with Manual Flash This describes wireless (multiple shooting) using manual flash. You can shoot with a different flash output setting for each slave unit 4. Wireless ID Settings (firing group). Set all parameters on the master unit. Change the wireless channels and wireless ID to avoid interference for it can only be triggered after the wireless IDs and channels of the MODE ZOOM SYNC SLAVE 1 Setting the flash mode to <M> ● Press the <MODE> Button master unit and the slave unit are set to the same. SET to set the flash to M mode. Press the <MENU> button to enter C.Fn ID. Press the <SET> button to choose OFF channel expansion shutdown, and choose any figure from 01 to 99. 2 Setting flash output ● Turn the Select Dial to set the flash output of the groups. - 41 - - 42 -

SET 3 Taking the picture ● Each group fires at the set flash ratio. ● Use the supplied mini stand to position the slave unit. ● Before shooting, perform a test flash and test shooting. ● The transmission distance might be shorter depending on the conditions such as positioning of slave units, the surrounding environment and whether conditions. 7. Multi: Wireless Flash Shooting with Manual Wireless Multiple Flash Shooting Flash You can divide the slave units into two or three groups and perform TTL autoflash while changing the flash ratio (factor). In addition, you MODE ZOOM SYNC SLAVE 1 Setting <Multi> stroboscopic flash. ● Long press the <MODE> can set and shoot with a different flash mode for each firing group, for up to 3 groups. SET button for 2 seconds so that ● Auto Shooting with Two Slave Groups <Multi> is displayed. Long press the <MODE> button A for 2 seconds again to exit. 2 Setting flash output/flash frequency/flash times. ● Setting the flash B output/flash frequency/flash times of the groups in the M mode. Setting the multi flash mode. (see Page39) ● Auto Shooting with Three Slave Groups ● A, B and C group can only C control the ON/OFF of the slave unit by pressing the A <MODE> Button. Using a flash (master/slave) with a radio transmission wireless B shooting function make it easy to shoot with advanced wireless multiple flash lighting, in the same way as TTL autoflash shooting. The basic relative position and operation range are as shown in the picture. You can then perform wireless TTL autoflash shooting just by setting the master unit to <TTL>. Slave/Master Unit's Positioning and Operation Range The Reason & Solution of Not Triggering in Godox 2.4G Wireless ● Autoflash Shooting with One Slave Unit 1. Disturbed by the 2.4G signal in outer environment (e.g. wireless base station, 2.4G wifi router, Bluetooth, etc.) → To adjust the channel CH setting on the flash trigger (add 10+ channels) and use the channel which is not disturbed. Or turn off the other 2.4G equipment in working. 2. Please make sure that whether the flash has finished its recycle or caught up with the continuous shooting speed or not(the flash ready indicator is lighten) and the flash is not under the state of over-heat Transmission distance is about 30m. protection or other abnormal situation. →Please downgrade the flash power output. If the flash is in TTL mode, please try to change it to M mode(a preflash is needed in TTL mode). - 43 - - 44 -

3. Whether the distance between the flash trigger and the flash is too close or not ● Ifthe wall or ceiling is too far away, the bounced flash might →Please turn on the “close distance wireless mode” on the flash trigger be too weak and result in underexposure. (＜0.5m): ● The wall or ceiling should be a plain, white color for high X1 series: press the test button and hold on, then turning it on until the flash reflectance. If the bounce surface is not white, a color cast ready indicator blinks for 2 times. may appear in the picture. XPro series: Set the C.Fn-DIST to 0-30m. 4. Whether the flash trigger and the receiver end equipment are in the low Creating a Catchlight battery states or not →Please replace the battery(the flash trigger is recommended to use 1.5V With the catchlight panel, you can create a catchlight in the subject’s disposable alkaline battery). eyes to add life to the facial expression. Other Applications 1 Point the flash head upward by 90°. Auto Focus Assist Beam Long press the C.Fn to enter C.Fn custom settings and press SET 2 Pull out the wide panel. The catchlight panel will come out at the same time. button: choose “ON” or “OFF” to turn on or off the to the AF-assist beam function . When turning on the AF-assist beam function: the red AF-assist lamp will light when it’s hard to focus while automatically off when getting correct focus. 3 Push the wide panel back in. ● Push in only the wide panel. ● Follow the same procedures ● When not attaching to the camera, the auto focus assist as for bounce flash. beam of V350S does not light up. ● When using on Interchangeable Lens Digital Cameras (e.g. ILCE6000L, a7RII, etc.), the auto focus assist beam of V350S does not light up. ● When only using on DSLR cameras (e.g. a99, a77II, etc.), ● Point the flash head straight ahead and then upward by 90°. the auto focus assist beam of V350S does light up. The catchlight will not appear if you swing the flash head left or right. Position Effective Range ● For best catchlight effect, stay 1.5m/4.9ft away from the subject. Center 0.6~4m Periphery ZOOM: Setting the Flash Coverage and Using 0.6~2.5m the Wide Panel Bounce Flash The flash coverage can be set automatically or manually. It can be By pointing the flash head toward a wall or ceiling, the flash will set to match the lens focal length from 24mm to 105mm. Also, with bounce off the surface before illuminating the subject. This can the built-in wide panel, the flash coverage can be expanded for soften shadows behind the subject for a more natural-looking shot. 14mm wide-angle lenses. This is called bounce flash. In Manual Zoom mode, press the MODE ZOOM SYNC SLAVE To set the bounce direction, hold the flash head and turn it to a <ZOOM> button. satisfying angle. -7-90 ● Turn the Select Dial to change SET the flash coverage. ● If <AU> is displayed, the flash 270 coverage will be set automatically. ● Ifyou set the flash coverage manually, make sure it covers the lens focal length so that the picture will not have a dark periphery. ● When the low battery indicator is displayed, the ZOOM can not be adjusted, it will constantly be 24mm. - 45 - - 46 -

Using the Wide Panel Pull out the wide panel and place it Protection Function over the flash head as shown. The flash coverage will then be extended 1. Over-Temperature Protection to 14 mm. ● To avoid overheating and deteriorating the flash head, do not fire ● The catchlight panel will come out more than 30 continuous flashes in fast succession at 1/1 full at the same time. Push the power. After 30 continuous flashes, allow a rest time of at least 10 catchlight panel back in. minutes. ● If you fire more than 30 continuous flashes and then fire more ● When pull out the wide panel, the ZOOM will constantly be flashes in short intervals, the inner over-temperature protection 14mm. The <ZOOM> button will not work. function may be activated and make the recycling time over 10 seconds. If this occurs, allow a rest time of about 10 minutes, and Low Battery Warning the flash unit will then return to normal. If the battery power is low, < > will ● When the over-temperature protection is started, is shown on appear and blink on the LCD panel. the LCD display. Please replace the battery Number of flashes that will activate over-temperature protection: immediately. When the low battery indicator is displayed, the ZOOM Power Output Level Number of Flashes can not be adjusted. 1/1 30 1/2 +0.7 40 1/2 +0.3 50 1/2 60 1/4(+0.3,+0.7) 100 1/8(+0.3,+0.7) 200 1/16(+0.3,+0.7) 300 1/32(+0.3,+0.7) 500 C.Fn: Setting Custom Functions 1/64(+0.3,+0.7) 1000 The following table lists the available and unavailable custom 1/128(+0.3,+0.7) functions of this flash. Number of flashes that will activate over-temperature protection in C.Fn Custom Functions high-speed sync triggering mode: Custom Function Function Setting No. Settings & Description Power Output Times Signs 1/1 15 ST Auto sleep ON ON 1/2(+0.3,+0.7); 20 (standby) OF OFF 1/4(+0.3,+0.7) 30 AF AF-assist beam ON ON 1/8(+0.3,+0.7); OF OFF 1/16(+0.3,+0.7) 40 BL Backlighting 10 sec. Off in 10 sec. control OF Always off 2. Other Protections ON Always lighting The system provides real-time protection to secure the device and ID Wireless ID OFF Off your safety. The following lists prompts for your reference: 01-99 Choose any figure from 01-99 Prompts on LCD Panel Meaning E1 A failure occurs on the recycling system so that the 1. Press the < ZOOM > Button for 2 seconds until C.Fn menu is flash cannot fire. displayed. Please restart the flash unit. If the problem still exists, 2. Turn the Select Dial to select the Custom Functions. please send this product to a maintenance center. E3 The voltage on two outlets of the flash tube is too high. 3. Press the <SET> Button and the Setting No. blinks. Please send this product to a maintenance center. 4. Turn the Select Dial to set the desired number. Pressing the E9 There are some errors occurred during the upgrading <SET> Button will confirm the settings. process. Please using the correct firmware upgrade 5. Press the <ZOOM> Button to exit. method. - 47 - - 48 -

Firmware Upgrade • Auto Focus Assist Beam Effective range (approx.) Center: 0.6~4m This flash supports firmware upgrade through the USB port. Update Periphery: 0.6~2.5m information will be released on our official website. • Power Supply • USB connection line is not included in this product. As the USB Lithium batteries 7.2V/2000mA port is a Micro USB socket, please use Micro USB connection line. • As the firmware upgrade needs the support of Godox G2 software, Recycle time 0.1s~1.7s please download and install the "Godox G2 firmware upgrade Full power flashes Over 500 software" before upgrading. Then, choose the related firmware file. • As the products needs to do firmware upgrade, please refer to Power saving Power off automatically after approx. 90 seconds instruction manual of the newest electric version as final. of idle operation. (60 minutes if set as slave) Checking the version: Press the <MODE> Button and the turn • Sync Triggering Mode Hotshoe, optic triggering the flash on. Then, the firmware update version (e.g. Version 1.0 will read U-1.0) will be displayed on the LCD panel. • Dimensions WxHxD 150*62*38 mm Technical Data Weight without battery 210g Weight with battery 290g Model V350S 2.4G Wireless Frequency 2412.999634MHz-2437.999878MHz • Type Range Compatible Cameras Sony camera (please refer to compatible camera models) Max. Transmitting Power 5dbm Guide No. 36 (m ISO 100) of 2.4G Wireless (1/1 output @ 105mm) Flash Coverage 24 to 105mm • Auto zoom (Flash coverage set automatically to match the lens focal length and image size) • Manual zoom • Swinging/tilting flash head (bounce flash): 0 to 270° horizontally and -7° to 90° vertically Flash Duration (t0.1) 1/350 to 1/20000 seconds • Exposure Control Exposure control system TTL autoflash and manual flash Flash exposure Manual. FEB: ±3 stops in 1/3 stop increments compensation (FEC) (Manual FEC can be combined.) Sync mode High-speed sync (up to 1/8000 seconds), first-curtain sync, and second-curtain sync Multi flash Provided (up to 90 times, 99Hz) • Wireless Flash (2.4G radio transmission) Wireless flash function Master, Slave, Off Controllable slave groups 3 (A, B and C) Transmission range ≤50m (approx.) Channels 16 (1~16) - 49 - - 50 -

Troubleshooting Compatible Camera Models If there is a problem, refer to this Troubleshooting Guide. This flash unit can be used on the following Sony camera models: α7RIII α7RII α7R α58 α99 ILCE6000L The Camera Flash cannot be charged. ● The battery is installed in the wrong direction. α77 II RX10 α9 →Install the battery in the correct direction. ● This table only lists the tested camera models, not all Sony cameras. ● The camera flash’s internal battery is exhausted. For the compatibility of other camera models, a self-test is recommended. →If < > appears and blinks on the LCD panel, recharge the ● Rights to modify this table are retained. battery immediately. The Camera Flash does not fire. ● The camera flash is not attached securely to the camera. →Attach the camera’s mounting foot securely to the camera. ● The electrical contacts of the Camera Flash and camera are dirty. Maintenance →Clean the contacts. ● Shut down the device immediately should abnormal operation be detected. ● Avoid sudden impacts and the product should be dedusted regularly. ● It is normal for the flash tube to be warm when in use. Avoid continuous flashes The power turns off by itself. if unnecessary. ● Maintenance of the flash must be performed by our authorized maintenance ● After 90 seconds of idle operation, auto power off took effect if the department which can provide original accessories. flash is set as master. ● This product, except consumables e.g. flash tube, is supported with a one-year warranty. →Press the shutter button halfway or press any flash button to ● Unauthorized service will void the warranty. wake up. ● If the product had failures or was wetted, do not use it until it is repaired by ● After 60 minutes of idle operation, the flash unit will enter sleep professionals. mode if it is set as slave. ● Changes made to the specifications or designs may not be reflected in this manual. →Press any flash button to wake up. Auto zoom does not work. ● The camera flash is not attached securely to the camera. →Attach the camera flash’s mounting foot to the camera. The flash exposure is underexposed or overexposed. ● You used high-speed sync. →With high-speed sync, the effective flash range will be shorter. Make sure the subject is within the effective flash range displayed. ● You used Manual Flash mode. →Set the flash mode to TTL or modify the flash output. Photos have dark corners or only parts of the target subject are illuminated. ● The focal length of lens exceeds the flash coverage. →Check the flash coverage you set. This flash unit has the flash coverage between 24 and 105mm, which fits medium-format cameras. Pull the wide panel out to extend the flash coverage. - 51 - - 52 -

FCC Statement "This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help." This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Changes or modifications not expressly approved by the part responsible for compliance could void the user's authority to operate the equipment. RSS statement: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.This equipment complies with Industry Canada radiation exposure limits set forth for an uncontrolled environment. Cet équipement est conforme à l'exposition aux rayonnements Industry Canada limites établies pour un environnement non contrôlé.


Document Created: 2018-07-24 14:53:13
Document Modified: 2018-07-24 14:53:13
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC