Test Report_JBP

FCC ID: 2ABGH-RC555L

Test Report

Download: PDF
FCCID_3611724

@l Report Number: 1709FE24—01 EMC Test Report Applicant : Reliance Communications LLC Product Type : GSM/CDMAAM/CDMA/LTE mobile phone Trade Name : Orbic Model Number : RCSSSL Applicable Standard : FCC 47 CFR PART 15 SUBPART B ANSI ©63.4; 2014 Receive Date : Sep. 07, 2017 Test Period : Sep. 09 ~Sep. 11, 2017 Issue Date : Oct. 12, 2017 Issue by A Test Lab Techno Corp. ;\igt-’gfg a‘», (\ ~ No. 140—1, Changan Street, Bade District, ibgg&s IAF Taoyuan City 33465, Taiwan (R.O.C) * ""** Tel : +886—3—2710188 / Fax : +886—3—2710190 Taiwan Accreditation Foundation accreditation number: 1330 Test Firm MRA designation number: TW1062 Note: This report shall not be reproduced except in full, without the. written. approval of A Test Lab Techno Corp. This document may be altered or revised by A Test Lab Techno Corp. personnel only, and shall be noted in the revision.section of the document. The client should not use it .to claim product endorsement by TAF, or any government agencies. The test results in the report only apply to the tested sample. Page 1 of 25

Report Number: 1709FE24-01 Revision History Rev. Issue Date Revisions Revised By 00 Oct. 02, 2017 Initial Issue Serene Yang 01 Oct. 12, 2017 Revised report information Serene Yang Page 2 of 25

@I Report Number: 1709FE24—01 Verification of Compliance Issued Date: Oct. 12, 2017 Applicant Reliance Communications LLC Product Type GSM/CDMAAVCDMA/LTE mobile phone Trade Name Orbic Model Number RCSS55L EUT Rated Voltage DC 5V, 2A or DC 9V, 2A Test Voltage 120 Vac / 60 Hz Applicable Standard FCC 47 CFR PART 15 SUBPART B ANSI C63.4: 2014 Test Result Complied Performing Lab. A Test Lab Techno Corp. «ns No. 140—1, Changan Street, Bade District, dIae=MRA Tacyuan City 33465, Taiwan (R.0.C) fay® Tel : +886—3—2710188 / Fax : +886—3—2710190 Taiwan Accreditation Foundation accreditation number: 1330 http:/Avww.atl—lab.com.tw/e—index.htm The above equipment has been tested by A Test Lab Techno Corp., and found compliance with the requirements set forth in the technical standards mentioned above. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Approved By : AJ) SEay l2 u_ Reviewed By : _Terry L]&O (Manager) (Misty Wu) (Testing Engineer) (Terry Liao) Page 3 of 25

Report Number: 1709FE24-01 TABLE OF CONTENTS 1 General Information ......................................................................................................... 5 1.1. Summary of Test Result ............................................................................................ 5 1.2. Testing Location ........................................................................................................ 5 1.3. Measurement Uncertainty ......................................................................................... 6 1.4. Test Site Environment ............................................................................................... 6 2 EUT Description................................................................................................................ 7 3 Test Methodology ............................................................................................................. 8 3.1. Decision of Test Mode ............................................................................................... 8 3.2. EUT Exercise Software ............................................................................................. 9 3.3. Configuration of Test System Details ...................................................................... 10 3.4. Test Instruments ...................................................................................................... 11 4 Measurement Procedure ................................................................................................ 13 4.1. Conducted Emission ............................................................................................... 13 4.2. Radiated Emission .................................................................................................. 15 5 Test Results .................................................................................................................... 18 5.1. Conducted Emission ............................................................................................... 18 5.2. Radiated Emission .................................................................................................. 21 Page 4 of 25

@l Report Number: 1709FE24—01 1 General Information 1.1. Summary of Test Result Emission Standard tem Verdict Remork Foo«r crr part 1s suspart a nsl cosa Conducted Emission PASS Meet Class Blimt Foo«r crr part 1s suspart a Meet Class B imit nsl ces + Radiated Emission PASS The test results ofthis report was related only to the tested semple(s identifed in this report. Manufacturer or whom it may concern should recognize the pass or fil of the test result 1.2. Testing Location Site Name A Test Lb Techno Corp hitp Jerem stteb com bwe—index. him Site Address: No. 140—1, Changan Street, Bade Distict, Teoyuan City 33465, Taiwan (R.0.C) Tel +se6—3—2710188 Fax +se6—3—2710100 Page § of25

Report Number: 1709FE24-01 1.3. Measurement Uncertainty Test Item Frequency Range Uncertainty (dB) 9kHz ~ 150kHz 2.7 Conducted Emission AC Power Port 150kHz ~ 30MHz 2.7 Test Item Test Site Frequency Range Uncertainty (dB) Horizontal 5.6 TE06 30MHz ~ 1000MHz Vertical 6.0 1000MHz ~ 6000MHz 5.2 6000MHz ~ 18000MHz 5.5 TE01 18000MHz ~ 26500MHz 4.8 Radiated Emission 26500MHz ~ 40000MHz 4.8 1000MHz ~ 6000MHz 4.9 6000MHz ~ 18000MHz 5.3 TE09 18000MHz ~ 26500MHz 4.5 26500MHz ~ 40000MHz 4.8 Note: The Vertical and Horizontal measurement uncertainty of 1GHz to 40GHz is evaluated and choose which polarity is worst value. 1.4. Test Site Environment Test Item Items Required (IEC 60068-1) Actual Temperature (C) 15-35 26 Conducted Emission Humidity (%RH) 25-75 60 Barometric pressure (mbar) 860-1060 950 Temperature (C) 15-35 26 Radiated Emission Humidity (%RH) 25-75 60 Barometric pressure (mbar) 860-1060 950 Page 6 of 25

@l Report Number: 1709FE24—01 2 EUT Description [Applcant Reliance Communications LLC 555 Wreless Bivd, Hauppauge, New York, 11788, United States Unimexcomm Menufacturer Reom 602, Building—8, Shenzhen Sofwere Park T3, Hi—Tech Pork South, Nan Shan Distict, Shenzhen, Chine Product Type GSMCDMAMWCDVALTE mobile phone Trade Name Orbic Model Number ressst ME! No assancos000 1802 Highest Operating seastilz Frequency Component List Trade Name Orbic Model Number [RCSSSL Adapter ve: 100—240vAc, soeoHz, 05A OfP: DC 5V, 2A or DC 8V, 2A Trade Name Orbic Model Number [RCSSSL Battery 3.8 VDC, 3000mAh 1O Port Desoription VO Port Types QTY Test Description 1}. USB Port 1 Connected to AC adapter 2), Audio Port 1 Connected to Earphone & Microphone Page 7 of25

Report Number: 1709FE24-01 3 Test Methodology 3.1. Decision of Test Mode 3.1.1. The following test mode(s) were scanned during the preliminary test: Pre-Test Mode Mode 1: IDLE mode Mode 2: Video Play + GSM 1900 / Bluetooth / Wi-Fi / GPS link + USB Cable 1_KOAR (White) with AC adapter mode Mode 3: Camera (Front) + CDMA (BC0) / Bluetooth / Wi-Fi / GPS link + USB Cable 1_KOAR (White) with AC adapter mode Mode 4: Camera (Rear) + WCDMA Band II / Bluetooth / Wi-Fi / GPS link + USB Cable 1_KOAR (White) CE with AC adapter mode Mode 5: REC + LTE Band 2/ Bluetooth / Wi-Fi / GPS link + USB Cable 1_KOAR (White) with AC adapter mode Mode 6: Data transmission + USB Cable 1_KOAR (White) with PC mode Mode 7: REC + LTE Band 2 / Bluetooth / Wi-Fi / GPS link + USB Cable 2_Ogle with AC adapter mode EMI Mode 1: IDLE mode Mode 2: Video Play + GSM 1900 / Bluetooth / Wi-Fi / GPS link + USB Cable 1_KOAR (White) with AC adapter mode Mode 3: Camera (Front) + CDMA (BC0) / Bluetooth / Wi-Fi / GPS link + USB Cable 1_KOAR (White) with AC adapter mode Mode 4: Camera (Rear) + WCDMA Band II / Bluetooth / Wi-Fi / GPS link + USB Cable 1_KOAR (White) RE with AC adapter mode Mode 5: REC + LTE Band 2 / Bluetooth / Wi-Fi / GPS link + USB Cable 1_KOAR (White) with AC adapter mode Mode 6: Data transmission + USB Cable 1_KOAR (White) with PC mode Mode 7: REC + LTE Band 2 / Bluetooth / Wi-Fi / GPS link+ USB Cable 2_Ogle with AC adapter mode Mode 8: REC + LTE Band 2 / Bluetooth / Wi-Fi / GPS link 3.1.2. After the preliminary scan, the following test mode was final mode and found to produce the highest emission level. Final Test Mode Conducted Emission Mode 5 Emission Below 1GHz Mode 5 Radiated Emission Above 1GHz Mode 5 The above highest emission mode of the configuration of the EUT and cable was chosen for all final test items. Page 8 of 25

Report Number: 1709FE24-01 3.2. EUT Exercise Software 1 Setup the EUT and simulators as shown on 3.3. 2 Turn on the power of all equipment. 3 The EUT link to (CBT) by Bluetooth function. 4 The EUT link to (SMU200A) by GPS function. 5 The EUT link to (MT8820C) by LTE function. 6 Activate Wi-Fi function, the EUT link to Notebook with AP. 7 Start to test get the worst reading. Measurement Software No. Description Software Version 1 Conducted Emission EZ EMC ATL-ITC-3A1-1 2 Radiated Emission _ Below 1GHz EZ EMC ATL-03A1-1 3 Radiated Emission _ Above 1GHz EZ EMC ATL-03A1 Page 9 of 25

Report Number: 1709FE24-01 3.3. Configuration of Test System Details Mode 5 Remote Site (1) (2) CBT MT8820C SMU200A Notebook AP AC Input AC EUT A Adapter B (3) Earphone & Microphone Signal Cable Type Signal Cable Description A USB Cable Shielded, 0.6m B Earphone & Microphone Cable Non-Shielded, 1.1m Devices Description Product Manufacturer Model Number Serial Number Power Cord (1) Notebook DELL LAPTITU 25627158361 R33002 (2) AP ASUS MSQ-RTAC66U D1AGG00126 R33005 Earphone & (3) SUN-YES ROCK 911 N/A N/A Microphone Page 10 of 25

Report Number: 1709FE24-01 3.4. Test Instruments Conducted Emission test site Equipment Manufacturer Model Number Serial Number Cal. Date Cal. Period Test Receiver R&S ESCI 100367 05/18/2017 1 year LISN R&S ENV216 101040 04/01/2017 1 year LISN R&S ENV216 101041 03/15/2017 1 year Radio Communication Anritsu MT8820C 6201060962 12/05/2016 1 year Analyzer Bluetooth Tester R&S CBT 100350 04/06/2017 2 years Signal Generator R&S SMU200A 102598 04/24/2017 1 year Test Site ATL TE02 TE02 N.C.R. ----- 10 Meter Chamber Equipment Manufacturer Model Number Serial Number Cal. Date Cal. Period Amplifier EMCI EMC9135 980298 02/09/2017 1 year Amplifier EMCI EMC9135 980299 02/17/2017 1 year Test Receiver R&S ESCI 100722 10/28/2016 1 year Test Receiver R&S ESCI 101000 12/12/2016 1 year SCHWARZBECK Broadband Antenna VULB 9168 670 02/13/2017 1 year MESS-ELEKTRONIK SCHWARZBECK Broadband Antenna VULB 9168 671 03/01/2017 1 year MESS-ELEKTRONIK Radio Communication Anritsu MT8820C 6201060962 12/05/2016 1 year Analyzer Bluetooth Tester R&S CBT 100350 04/06/2017 2 years Signal Generator R&S SMU200A 102598 04/24/2017 1 year Test Site ATL TE06 TE06 10/30/2016 1 year Note: N.C.R. = No Calibration Request. Page 11 of 25

Report Number: 1709FE24-01 3 Meter Chamber (966B) Equipment Manufacturer Model Number Serial Number Cal. Date Cal. Period Spectrum Analyzer Agilent E4445A MY46181986 05/24/2017 1 year Pre Amplifier Agilent 8447D 2944A11120 12/21/2016 1 year Amplifier Agilent 8449B 3008A02237 10/11/2016 1 year Pre Amplifier EMCI EMC012645SE 980289 01/17/2017 1 year Pre Amplifier EMCI EMC2654045 980028 08/20/2017 1 year RF Pre-selector Agilent N9039A MY46520255 05/24/2017 1 year Double Ridged Horn Antenna ETS 3117 00152321 10/12/2016 1 year (1~18GHz) Horn Antenna ETS 3116 00086467 09/12/2016 1 year (18~40GHz) SCHWARZBECK Broadband Antenna VULB 9168 419 11/03/2016 1 year MESS-ELEKTRONIK Radio Communication Anritsu MT8820C 6201060962 12/05/2016 1 year Analyzer Bluetooth Tester R&S CBT 100350 04/06/2017 2 years Signal Generator R&S SMU200A 102598 04/24/2017 1 year Test Site ATL TE09 TE09 04/21/2017 1 year Note: N.C.R. = No Calibration Request. Page 12 of 25

Report Number: 1709FE24-01 4 Measurement Procedure 4.1. Conducted Emission  Test Setup Page 13 of 25

@l Report Number: 1709FE24—01 m Test Procedure The EUT and simulators are connected to the main power through a line impedance stabilzation network (L.1S N. This provides a S0D // SOuH coupling impedance for the meesuring equipment. The peripheral devices are also connected to the main power through a LISN that provides 2 500/SOuH coupling impedance with 50ohm termination Tabletop deviceshall be placed on a non—conducting platforn, of nominalsize 1 m by 1.5 m raised 80 om above the reference ground plane. The wall of sereened room shallbe located 4dom to the rear ofthe EUT. Other surtaces of tabletop or foor standing EUT shall be at least 8dom from any other ground conducting surface incluing one or more LISNs. For floor—standing device shallbe placed under the EUT wth a 1 2mm insuleting material Conducted emissions were investigated over the frequency range from 0.15 Miz to 30 MHz using a resolution bandiidth of 9 k. The equipment under test (EUT) shall be meet the limitsin section 4.1.1, as applicable, including the everage Imit and the quas—peak Imit when using respectively, an average detector and quasi—pek detector measured in accordance with the methods described of related standard. When allof peak value were complied with quasi—peak and average lmit fom 150kHz to 30Mz then quasi—peak and average measurement was unnecessery The AMN shall be placed 0.8 m from the boundary of the unit under test and bonded to a ground reference plane for ANMNs mounted on top ofthe ground reference plane. This distance is between the closest points ofthe AVN and the EUT All other unis of the EUT and essocisted equipment shall be at least 0,8 m from the ANN. f the mains power cable is longer then 1m then the eable shall be folded back and forth at the centre ofthe lead to form a bundle no longer then 0.4m. Allofinterconnectng oables that hang ctoser than 4dom to the ground plane shall be folded back and forth in the center forming a bundle 30 m to 40 om long. Allof EUT and AE shall be separate place more than 0.tm. All 50 0 ports ofthe LISN shall be resistvely terminated into 50 C loads when not connected to the measuring instrument If the reading ofthe measuring receiver shows fuctustions close to the limit,the reading shall be observed for at least 155 at each measurement frequency;the higher reading shallbe recorded with the exception of any brief isolated high reading which shall be ignored Page 14 of 25

@l Report Number: 1709FE24—01 4.2. Radiated Emission m Test Sotup Below 1GHz imtogm _ _V . w—____— aolt —nfl > Ground Plane Measurement ooz3 Instrument +C ayal [Gontrollel t 1 Control Room Above 1GHz 7 Antemna t zm on |1 Hom * anns eur 4 Svectun A anaizer po[ 1 Tumuse .¥ 0n 0| 1 1 stom 88 A | x reams |[LIES a TC———_——J Page 15 of 25

Report Number: 1709FE24-01 Test arrangement for radiated emissions of tabletop equipment. Page 16 of 25

Report Number: 1709FE24-01  Test Procedure Below 1GHz The EUT and its simulators are placed on a turn table which is 0.8 meter above ground. When the EUT is floor- standing equipment, it is placed on the ground plane which has a 12 mm non-conductive covering to insulate the EUT from the ground plane. The turn table is 0.8m height and 2.0m wide x 1.0m deep size. It can rotate 360 degrees to determine the position of the maximum emission level. The spcing between the each equipment was 10cm. The mains cables are dropped to floor and are round to recepatacle. Interconnecting cables of table top equipment that hang closer than 0.4m to the ground plane are folded back and forth forming a bundle 0.3m to 0.4m long, hanging approximately in the middle between ground plane and table. The EUT was positioned such that the distance from antenna to the EUT was 10 meters and the receive antenna was moved from 1m to 4m to investigate maximum highest emission at least 6 points over the frequency range from 30MHz to1GHz using a resolution bandwidth of 120 kHz and measured by the quasi-peak detector. According to this standard paragraph 15.109, as an alternative to the radiated emission limits, digital devices may be shown to comply with the standards contained in Third Edition of the International Special Committee on Radio Interference (CISPR), Pub. 22, “Information Technology Equipment - Radio Disturbance Characteristics - Limits and Methods of Measurement”. Above 1GHz The Setup is same as Below 1GHz placement. The turn table is 0.8m height and 1.8m wide x 1.0m deep size. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 3 meter for above 1GHz, the highest frequency performed according to internal source frequency of the EUT, the specification was below: Highest frequency generated or used in the device or on Upper frequency of measurement range (MHz) which the device operates or tunes (MHz) Below 1.705 30 1.705 - 108 1000 108 - 500 2000 500 - 1000 5000 5th harmonic of the highest frequency or 40 GHz, Above 1000 whichever is lower Absorber shall be spread between floor of a turn table and a receive antenna shown in 4.2.3. The antenna used boresight antenna master from 1 meter and 4 meters to find out the maximum emission level and find the highest emission at least 6 points. Both horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission, all of the interface cables must be manipulated on radiated measurement. Radiated emissions were applied to above 1GHz using a resolution bandwidth of 1MHz and measured by the peak and average detector which antenna to the EUT distance was 3meters. If the EUT was meet both limits and measurement with the average detector receiver is unnecessary. Page 17 of 25

Report Number: 1709FE24-01 5 Test Results 5.1. Conducted Emission  Limit Class A (dBuV) Class B (dBuV) Frequency (MHz) Quasi-peak Average Quasi-peak Average 0.15 - 0.5 79 66 66 - 56 56 - 46 0.50 - 5.0 73 60 56 46 5.0 - 30.0 73 60 60 50 Note: (1) The lower limit shall apply at the transition frequencies. (2) The limit decreases in line with the logarithm of the frequency in the range 0.15 to 0.50 MHz. Page 18 of 25

Report Number: 1709FE24-01  Test Result Test Standard: FCC Part 15B Power Line: L1 Test Mode: Mode 5 Test Power: AC 120V/60Hz Description: No. Frequency QP AVG Correction QP AVG QP AVG QP AVG Remark reading reading factor result result limit limit margin margin (MHz) (dBuV) (dBuV) (dB) (dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB) 1 0.3940 32.75 22.56 9.65 42.40 32.21 57.98 47.98 -15.58 -15.77 Pass 2 0.4660 31.12 21.96 9.67 40.79 31.63 56.58 46.58 -15.79 -14.95 Pass 3 0.5940 29.73 17.95 9.68 39.41 27.63 56.00 46.00 -16.59 -18.37 Pass 4 0.7940 28.10 16.99 9.69 37.79 26.68 56.00 46.00 -18.21 -19.32 Pass 5 1.6340 24.71 12.25 9.73 34.44 21.98 56.00 46.00 -21.56 -24.02 Pass 6 17.4660 27.47 18.47 10.20 37.67 28.67 60.00 50.00 -22.33 -21.33 Pass Note: 1. Result (dBuV) = Correction factor (dB) + Reading(dBuV). 2. Correction factor (dB) = Cable loss (dB) + L.I.S.N. factor (dB). Page 19 of 25

Report Number: 1709FE24-01 Test Standard: FCC Part 15B Power Line: N Test Mode: Mode 5 Test Power: AC 120V/60Hz Description: No. Frequency QP AVG Correction QP AVG QP AVG QP AVG Remark reading reading factor result result limit limit margin margin (MHz) (dBuV) (dBuV) (dB) (dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB) 1 0.1500 31.16 12.13 9.62 40.78 21.75 66.00 56.00 -25.22 -34.25 Pass 2 0.2060 31.57 16.75 9.64 41.21 26.39 63.37 53.37 -22.16 -26.98 Pass 3 0.2740 27.47 13.15 9.65 37.12 22.80 61.00 51.00 -23.88 -28.20 Pass 4 0.3980 27.49 18.54 9.65 37.14 28.19 57.90 47.90 -20.76 -19.71 Pass 5 0.4780 25.80 15.96 9.66 35.46 25.62 56.37 46.37 -20.91 -20.75 Pass 6 17.3660 26.13 14.43 10.22 36.35 24.65 60.00 50.00 -23.65 -25.35 Pass Note: 1. Result (dBuV) = Correction factor (dB) + Reading(dBuV). 2. Correction factor (dB) = Cable loss (dB) + L.I.S.N. factor (dB). Page 20 of 25

Report Number: 1709FE24-01 5.2. Radiated Emission  Limit Under 1GHz test shall not exceed following value FCC 47 CFR PART 15 SUBPART B Class A Class B Frequency range (MHz) Distance (m) dBuV/m Distance (m) dBuV/m 30 to 88 10 39 3 40 88 to 216 10 43.5 3 43.5 216 to 960 10 46.4 3 46 Above 960 10 49.5 3 54 CISPR 22 Class A Class B Frequency range (MHz) Distance (m) dBuV/m Distance (m) dBuV/m 30 to 230 10 40 10 30 230 to 1000 10 47 10 37 Above 1GHz test shall not exceed following value dBuV/m (Distance 3m) Frequency Class A Class B (MHz) Average Peak Average Peak 1000 ~ 40000 60 80 54 74 Remark: 1. The tighter limit shall apply at the edge between two frequency bands. 2. Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. 3. RF Voltage (dBuV/m) = 20 log RF Voltage (uV/m) 4. Peak detector limit is corresponding to 20 dB above the maximum permitted average limit. According to FCC Part 15.33 (b), for an unintentional radiator, including a digital device, the spectrum shall be investigated from the lowest radio frequency signal generated or used in the device, without going below the lowest frequency for which a radiated emission limit is specified, up to the frequency shown in the following table: Highest frequency generated or used in the device or in which Upper frequency of measurement range the device operated or tunes (MHz) (MHz) Below 1.75 30 1.75-108 1000 108-500 2000 500-1000 5000 5th harmonic of the highest frequency or 40GHz, Above 1000 whichever is lower Page 21 of 25

Report Number: 1709FE24-01  Test Result Test Standard: FCC Part 15B Test Distance: 10m Test Mode: Mode 5 Test Power: AC 120V/60Hz Measurement Range: 30MHz~1GHz Ant.Polar.: Horizontal Frequency Reading Correct Factor Result Limit Margin Height Degree No. Remark (MHz) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dB) (cm) ( °) 1 175.5000 31.99 -18.09 13.90 33.50 -19.60 100 312 QP 2 459.7100 25.46 -6.89 18.57 36.00 -17.43 200 51 QP 3 532.4600 26.09 -8.84 17.25 36.00 -18.75 200 254 QP 4 663.4100 25.47 -5.34 20.13 36.00 -15.87 100 11 QP 5 671.1700 24.49 -4.86 19.63 36.00 -16.37 100 182 QP 6 711.9100 25.56 -5.44 20.12 36.00 -15.88 103 360 QP Note: 1. Result (dBuV/m) = Correction factor (dB/m) + Reading(dBuV). 2. Correction factor (dB/m) = Antenna Factor (dB/m) + Cable loss (dB) – Pre-Amplifier gain (dB). Page 22 of 25

Report Number: 1709FE24-01 Test Standard: FCC Part 15B Test Distance: 10m Test Mode: Mode 5 Test Power: AC 120V/60Hz Measurement Range: 30MHz~1GHz Ant.Polar.: Vertical Frequency Reading Correct Factor Result Limit Margin Height Degree No. Remark (MHz) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dB) (cm) ( °) 1 35.8200 44.09 -24.31 19.78 30.00 -10.22 101 360 QP 2 148.3400 35.95 -17.15 18.80 33.50 -14.70 100 313 QP 3 176.4700 38.48 -16.33 22.15 33.50 -11.35 100 329 QP 4 649.8300 27.32 -5.18 22.14 36.00 -13.86 100 48 QP 5 690.5700 26.44 -3.38 23.06 36.00 -12.94 200 283 QP 6 709.9700 25.10 -3.18 21.92 36.00 -14.08 100 357 QP Note: 1. Result (dBuV/m) = Correction factor (dB/m) + Reading(dBuV). 2. Correction factor (dB/m) = Antenna Factor (dB/m) + Cable loss (dB) – Pre-Amplifier gain (dB). Page 23 of 25

Report Number: 1709FE24-01 Test Standard: FCC Part 15B Test Distance: 3m Test Mode: Mode 5 Test Power: AC 120V/60Hz Measurement Range: 1GHz~40GHz Ant.Polar.: Horizontal Frequency Reading Correct Factor Result Limit Margin Height Degree No. Remark (MHz) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dB) (cm) ( °) 1 4900.000 51.94 -7.49 44.45 74.00 -29.55 165 360 peak 2 4900.000 42.14 -7.49 34.65 54.00 -19.35 165 360 AVG 3 5290.000 51.48 -7.19 44.29 74.00 -29.71 200 37 peak 4 5290.000 41.57 -7.19 34.38 54.00 -19.62 200 37 AVG 5 6460.000 51.57 -5.02 46.55 74.00 -27.45 100 265 peak 6 6460.000 40.55 -5.02 35.53 54.00 -18.47 100 265 AVG 7 7084.000 51.18 -4.38 46.80 74.00 -27.20 100 7 peak 8 7084.000 42.89 -4.38 38.51 54.00 -15.49 100 7 AVG 9 7786.000 50.30 -3.24 47.06 74.00 -26.94 200 300 peak 10 7786.000 40.10 -3.24 36.86 54.00 -17.14 200 300 AVG 11 8293.000 50.04 -2.35 47.69 74.00 -26.31 200 348 peak 12 8293.000 39.84 -2.35 37.49 54.00 -16.51 200 348 AVG Note: 1. Result (dBuV/m) = Correction factor (dB/m) + Reading(dBuV). 2. Correction factor (dB/m) = Antenna Factor (dB/m) + Cable loss (dB) – Pre-Amplifier gain (dB). Page 24 of 25

Report Number: 1709FE24-01 Test Standard: FCC Part 15B Test Distance: 3m Test Mode: Mode 5 Test Power: AC 120V/60Hz Measurement Range: 1GHz~40GHz Ant.Polar.: Vertical Frequency Reading Correct Factor Result Limit Margin Height Degree No. Remark (MHz) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dB) (cm) ( °) 1 6538.000 51.41 -4.85 46.56 74.00 -27.44 100 96 peak 2 6538.000 42.56 -4.85 37.71 54.00 -16.29 100 96 AVG 3 7162.000 50.99 -4.23 46.76 74.00 -27.24 200 146 peak 4 7162.000 41.77 -4.23 37.54 54.00 -16.46 200 146 AVG 5 7669.000 50.91 -3.47 47.44 74.00 -26.56 200 0 peak 6 7669.000 39.87 -3.47 36.40 54.00 -17.60 200 0 AVG 7 9190.000 48.29 -0.02 48.27 74.00 -25.73 100 281 peak 8 9190.000 39.45 -0.02 39.43 54.00 -14.57 100 281 AVG 9 10009.000 47.84 1.18 49.02 74.00 -24.98 100 120 peak 10 10009.000 38.41 1.18 39.59 54.00 -14.41 100 120 AVG 11 12037.000 13.37 38.53 51.90 74.00 -22.10 100 23 peak 12 12037.000 5.75 38.53 44.28 54.00 -9.72 100 23 AVG Note: 1. Result (dBuV/m) = Correction factor (dB/m) + Reading(dBuV). 2. Correction factor (dB/m) = Antenna Factor (dB/m) + Cable loss (dB) – Pre-Amplifier gain (dB). Page 25 of 25


Document Created: 2017-10-12 15:25:03
Document Modified: 2017-10-12 15:25:03
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC