Test Report

FCC ID: 2ABES-ULTRA8

Test Report

Download: PDF
FCCID_2624284

MRT Technology (Suzhou) Co., Ltd Report No.: 1504RSU01801 Phone: +86-512-66308358 Report Version: V02 Fax: +86-512-66308368 Issue Date: 05-25-2015 Web: www.mrt-cert.com MEASUREMENT REPORT FCC PART 15.249 FCC ID: 2ABES-ULTRA8 APPLICANT: Pathway Innovations and Technologies, Inc. Application Type: Certification Product: Remote Control Model No.: Ultra8, Ultra13, Ultra18, Ultra25, U800, U1300, U1800, U2500 FCC Classification: Low Power Communication Device Transmitter (DXX) FCC Rule Part(s): Part 15.249 Test Procedure(s): ANSI C63.10-2009 Test Date: Apr. 25 ~ May 21, 2015 Reviewed By : ( Robin Wu ) Approved By : ( Marlin Chen ) The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.10-2009. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. FCC ID: 2ABES-ULTRA8 Page Number: 1 of 29

Report No.: 1504RSU01801 Revision History Report No. Version Description Issue Date 1504RSU01801 Rev. 01 Initial report 05-21-2015 1504RSU01801 Rev. 02 Revised the description of test Software 05-25-2015 FCC ID: 2ABES-ULTRA8 Page Number: 2 of 29

Report No.: 1504RSU01801 CONTENTS Description Page 1. INTRODUCTION ..................................................................................................................... 5 1.1. Scope ........................................................................................................................... 5 1.2. MRT Test Location ....................................................................................................... 5 2. PRODUCT INFORMATION ..................................................................................................... 6 2.1. Equipment Description.................................................................................................. 6 2.2. Mode of Operation ........................................................................................................ 6 2.3. Test Configuration ........................................................................................................ 6 2.4. EMI Suppression Device(s)/Modifications ..................................................................... 6 2.5. Labeling Requirements ................................................................................................. 6 2.6. Test Software ............................................................................................................... 7 3. DESCRIPTION OF TEST ........................................................................................................ 8 3.1. Evaluation Procedure ................................................................................................... 8 3.2. AC Line Conducted Emissions ..................................................................................... 8 3.3. Radiated Emissions ...................................................................................................... 9 4. ANTENNA REQUIREMENTS ................................................................................................ 10 5. TEST EQUIPMENT CALIBRATION DATE .............................................................................11 6. MEASUREMENT UNCERTAINTY ......................................................................................... 12 7. TEST RESULT ...................................................................................................................... 13 7.1. Summary .................................................................................................................... 13 7.2. Conducted Emission ................................................................................................... 14 7.2.1. Test Limit ................................................................................................................ 14 7.2.2. Test Setup............................................................................................................... 14 7.2.3. Test Result .............................................................................................................. 14 7.3. Radiated Emission ...................................................................................................... 15 7.3.1. Test Limit ................................................................................................................ 15 7.3.2. Test Setup............................................................................................................... 16 7.3.3. Test Result .............................................................................................................. 18 7.4. Radiated Outside of The Specified Frequency Bands Measurement........................... 21 7.4.1. Test Result .............................................................................................................. 21 8. CONCLUSION....................................................................................................................... 29 FCC ID: 2ABES-ULTRA8 Page Number: 3 of 29

Report No.: 1504RSU01801 §2.1033 General Information Applicant: Pathway Innovations and Technologies, Inc. Applicant Address: 10211 Pacific Mesa Blvd, #412, San Diego, CA 92121, USA Manufacturer: Shenzhen Kerun Visual Technology Co., Ltd Manufacturer Address: 6/F, Building 2, Zone S2, 1213 Liuxian Blvd, Honghualing Industrial Park, Nanshan District, Shenzhen, Guangdong, China Test Site: MRT Technology (Suzhou) Co., Ltd Test Site Address: D8 Building, Youxin Industrial Park, No.2 Tian’edang Rd., Wuzhong Economic Development Zone, Suzhou, China MRT Registration No.: 809388 FCC Rule Part(s): Part 15.249 Model No.: Ultra8, Ultra13, Ultra18, Ultra25, U800, U1300, U1800, U2500 FCC ID: 2ABES-ULTRA8 Test Device Serial No.: N/A Production Pre-Production Engineering FCC Classification: Low Power Communication Device Transmitter (DXX) Test Facility / Accreditations Measurements were performed at MRT Laboratory located in Tian’edang Rd., Suzhou, China.  MRT facility is a FCC registered (MRT Reg. No. 809388) test facility with the site description report on file and has met all the requirements specified in Section 2.948 of the FCC Rules.  MRT facility is an IC registered (MRT Reg. No. 11384A-1) test laboratory with the site description on file at Industry Canada.  MRT facility is a VCCI registered (R-4179, G-814, C-4664, T-2206) test laboratory with the site description on file at VCCI Council.  MRT Lab is accredited to ISO 17025 by the American Association for Laboratory Accreditation (A2LA) under the American Association for Laboratory Accreditation Program (A2LA Cert. No. 3628.01) in EMC, Telecommunications and Radio testing for FCC, Industry Canada, EU and TELEC Rules. FCC ID: 2ABES-ULTRA8 Page Number: 4 of 29

Report No.: 1504RSU01801 1. INTRODUCTION 1.1. Scope Measurement and determination of electromagnetic emissions (EMC) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Industry Canada Certification and Engineering Bureau. 1.2. MRT Test Location The map below shows the location of the MRT LABORATORY, its proximity to the Taihu Lake. These measurement tests were conducted at the MRT Technology (Suzhou) Co., Ltd. Facility located at D8 Building, Youxin Industrial Park, No.2 Tian’edang Rd., Wuzhong Economic Development Zone, Suzhou, China. The detailed description of the measurement facility was found to be in compliance with the requirements of § 2.948 according to ANSI C63.4-2009 on September 30, 2013. FCC ID: 2ABES-ULTRA8 Page Number: 5 of 29

Report No.: 1504RSU01801 2. PRODUCT INFORMATION 2.1. Equipment Description Product Name Remote Control Model No. Ultra8, Ultra13, Ultra18, Ultra25, U800, U1300, U1800, U2500 Working Voltage DC 3.0V Working Frequency 2403 MHz ~ 2480MHz Type of Modulation GFSK Antenna Type PCB Antenna Antenna Gain 2dBi 2.2. Mode of Operation All the test modes were carried out with the EUT in normal operation, which was shown in this test report and defined as: Test Mode Mode 1: Transmit 2.3. Test Configuration The Remote Control FCC ID: 2ABES-ULTRA8 was tested as described in this report is in compliance with the requirements limits of FCC Rules Part 15.207,15.209, 15.215 and 15.249. ANSI C63.10-2009 was used to reference the appropriate EUT setup for radiated spurious emissions testing and AC line conducted testing. 2.4. EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and/or no modifications were made during testing. 2.5. Labeling Requirements Per 2.1074 & 15.19; Docket 95-19 The label shall be permanently affixed at a conspicuous location on the device; instruction manual or pamphlet supplied to the user and be readily visible to the purchaser at the time of purchase. However, when the device is so small wherein placement of the label with specified statement is not practical, only the trade name and FCC ID must be displayed on the device per Section 15.19(a)(5). Please see attachment for FCC ID label and label location. FCC ID: 2ABES-ULTRA8 Page Number: 6 of 29

Report No.: 1504RSU01801 2.6. Test Software The test unit set it by pressing the down , left ,or right button on the EUT and make the EUT work through batteries, the EUT will enter the test mode and continues transmits signal. FCC ID: 2ABES-ULTRA8 Page Number: 7 of 29

Report No.: 1504RSU01801 3. DESCRIPTION OF TEST 3.1. Evaluation Procedure The measurement procedures described in the American National Standard for Testing Unlicensed Wireless Devices (ANSI C63.10-2009), and the requirements provided in FCC 15.207, 15.209, 15.215 and 15.249 were performed in the report of the Remote Control FCC ID: 2ABES-ULTRA8. Deviation from measurement procedure…………………………….....................................None 3.2. AC Line Conducted Emissions The line-conducted facility is located inside an 8'x4'x4' shielded enclosure. A 1m x 2m wooden table 80cm high is placed 40cm away from the vertical wall and 80cm away from the sidewall of the shielded room. Two 10kHz-30MHz, 50Ω/50uH Line-Impedance Stabilization Networks (LISNs) are bonded to the shielded room floor. Power to the LISNs is filtered by external high-current high-insertion loss power line filters. These filters attenuate ambient signal noise from entering the measurement lines. These filters are also bonded to the shielded enclosure. The EUT is powered from one LISN and the support equipment is powered from the second LISN. All interconnecting cables more than 1 meter were shortened to a 1 meter length by non-inductive bundling (serpentine fashion) and draped over the back edge of the test table. All cables were at least 40cm above the horizontal reference ground-plane. Power cables for support equipment were routed down to the second LISN while ensuring that that cables were not draped over the second LISN. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The RF output of the LISN was connected to the receiver and exploratory measurements were made to determine the frequencies producing the maximum emission from the EUT. The receiver was scanned from 150kHz to 30MHz. The detector function was set to peak mode for exploratory measurements while the bandwidth of the analyzer was set to 9kHz. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Each emission was also maximized by varying: power lines, the mode of operation or data exchange speed, or support equipment whichever determined the worst-case emission. Once the worst case emissions have been identified, the one EUT cable configuration/arrangement and mode of operation that produced these emissions is used for final measurements on the same test site. The analyzer is set to CISPR quasi-peak and average detectors with a 9kHz resolution bandwidth for final measurements. An extension cord was used to connect to a single LISN which powered by EUT. The extension cord was calibrated with LISN, the impedance and insertion loss are compliance with the requirements as stated in ANSI C63.10-2009 at Clause 4.3. Line conducted emissions test results are shown in Section 7.2. FCC ID: 2ABES-ULTRA8 Page Number: 8 of 29

Report No.: 1504RSU01801 3.3. Radiated Emissions The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi-anechoic chamber which is shielded from any ambient interference. For measurements above 1GHz absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections. For measurements below 1GHz, the absorbers are removed. A MF Model 210SS turntable is used for radiated measurement. It is a continuously rotatable, remote controlled, metallic turntable and 2 meters (6.56 ft.) in diameter. The turn table is flush with the raised floor of the chamber in order to maintain its function as a ground plane. An 80cm high PVC support structure is placed on top of the turntable. For all measurements, the spectrum was scanned through all EUT azimuths and from 1 to 4 meter receive antenna height using a broadband antenna from 30MHz up to the upper frequency shown in 15.33(b)(1) depending on the highest frequency generated or used in the device or on which the device operates or tunes. For frequencies above 1GHz, linearly polarized double ridge horn antennas were used. For frequencies below 30MHz, a calibrated loop antenna was used. When exploratory measurements were necessary, they were performed at 1 meter test distance inside the semi-anechoic chamber using broadband antennas, broadband amplifiers, and spectrum analyzers to determine the frequencies and modes producing the maximum emissions. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The test set-up was placed on top of the 0.8 meter high, 1 x 1.5 meter table. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Appropriate precaution was taken to ensure that all emissions from the EUT were maximized and investigated. The system configuration, clock speed, mode of operation or video resolution, if applicable, turntable azimuth, and receive antenna height was noted for each frequency found. Final measurements were made in the semi-anechoic chamber using calibrated, linearly polarized broadband and horn antennas. The test setup was configured to the setup that produced the worst case emissions. The spectrum analyzer was set to investigate all frequencies required for testing to compare the highest radiated disturbances with respect to the specified limits. The turntable containing the EUT was rotated through 360 degrees and the height of the receive antenna was varied 1 to 4 meters and stopped at the azimuth and height producing the maximum emission. Each emission was maximized by changing the orientation of the EUT through three orthogonal planes and changing the polarity of the receive antenna, whichever produced the worst-case emissions. According to 3dB BeamWidth of horn antenna, the horn antenna should be always directed to the EUT when rising height. FCC ID: 2ABES-ULTRA8 Page Number: 9 of 29

Report No.: 1504RSU01801 4. ANTENNA REQUIREMENTS Excerpt from §15.203 of the FCC Rules/Regulations: “An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by the responsible party can be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section.”  The antenna of the Remote Control is permanently attached.  There are no provisions for connection to an external antenna. Conclusion: The Remote Control FCC ID: 2ABES-ULTRA8 unit complies with the requirement of §15.203. FCC ID: 2ABES-ULTRA8 Page Number: 10 of 29

Report No.: 1504RSU01801 5. TEST EQUIPMENT CALIBRATION DATE Radiated Emission Instrument Manufacturer Type No. Asset No. Cali. Interval Cali. Due Date Spectrum Analyzer Agilent N9020A MRTSUE06106 1 year 2016/04/23 Preamplifier Agilent 83017A MRTSUE06076 1 year 2015/12/13 Loop Antenna Schwarzbeck FMZB1519 MRTSUE06025 1 year 2015/11/08 TRILOG Antenna Schwarzbeck VULB9162 MRTSUE06022 1 year 2015/11/08 Broad-Band Horn Antenna Schwarzbeck BBHA9120D MRTSUE06023 1 year 2015/11/08 Broadband Horn Antenna Schwarzbeck BBHA9170 MRTSUE06024 1 year 2015/12/11 Temperature/Humidity Meter Anymetre TH101B MRTSUE06046 1 year 2015/11/14 FCC ID: 2ABES-ULTRA8 Page Number: 11 of 29

Report No.: 1504RSU01801 6. MEASUREMENT UNCERTAINTY Where relevant, the following test uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2. This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k = 2. Radiated Emission Measurement Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 9kHz ~ 1GHz: ± 4.18dB 1GHz ~ 18GHz: ± 4.76dB FCC ID: 2ABES-ULTRA8 Page Number: 12 of 29

Report No.: 1504RSU01801 7. TEST RESULT 7.1. Summary Company Name: Pathway Innovations and Technologies, Inc. FCC ID: 2ABES-ULTRA8 FCC Part Test Test Test Description Test Limit Reference Section(s) Condition Result AC Conducted Emissions Line 15.207 < FCC 15.207 limits N/A Section 7.2 150kHz - 30MHz Conducted Emissions radiated outside of the specified frequency bands, except for harmonics, shall be 15.209 General Field Strength attenuated by at least Section 7.3 Radiated Pass 15.249 Limits 50 dB below the level & 7.4 of the fundamental or to the general radiated emission limits in §15.209, whichever is the lesser attenuation. Notes: 1) All modes of operation and data rates were investigated. For radiated emission test, every axis (X, Y, Z) was also verified. The test results shown in the following sections represent the worst case emissions. 2) The analyzer plots shown in this section were all taken with a correction table loaded into the analyzer. The correction table was used to account for the losses of the cables and attenuators used as part of the system to connect the EUT to the analyzer at all frequencies of interest. 3) All antenna port conducted emissions testing was performed on a test bench with the antenna port of the EUT connected to the spectrum analyzer through calibrated cables and attenuators. FCC ID: 2ABES-ULTRA8 Page Number: 13 of 29

Report No.: 1504RSU01801 7.2. Conducted Emission 7.2.1. Test Limit FCC Part 15 Subpart C Paragraph 15.207 Limits Frequency QP AV (MHz) (dBuV) (dBuV) 0.15 - 0.50 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30 60 50 Note 1: The lower limit shall apply at the transition frequencies. Note 2: The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz to 0.5 MHz. 7.2.2. Test Setup 7.2.3. Test Result The EUT was battery-powered device, not applicable for this test item. FCC ID: 2ABES-ULTRA8 Page Number: 14 of 29

Report No.: 1504RSU01801 7.3. Radiated Emission 7.3.1. Test Limit FCC Part 15 Subpart C Paragraph 15.209 Frequency Field Strength Measurement Distance (MHz) (microvolts/meter) (uV/m) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 30-80 100** 3 80-216 150** 3 216-960 200** 3 Above 960 500 3 Note 1: The lower limit shall apply at the transition frequency. Note 2: Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. Note 3: E field strength (dBuV/m) = 20 log E field strength (uV/m). FCC Part 15 Subpart C Paragraph 15.249 Field Strength of Fundamental Field Strength of Harmonics Fundamental Frequency (millivolts/meter) (microvolts/meter) 902-928(MHz) 50 500 2400-2483.5(MHz) 50 500 5725-5875(MHz) 50 500 24.0-24.25(GHz) 250 2500 FCC Part 15.249 (d), Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general FCC ID: 2ABES-ULTRA8 Page Number: 15 of 29

Report No.: 1504RSU01801 radiated emission limits in §15.209, whichever is the lesser attenuation. 7.3.2. Test Setup 9kHz ~ 30MHz Test Setup: 30MHz ~ 1GHz Test Setup: FCC ID: 2ABES-ULTRA8 Page Number: 16 of 29

Report No.: 1504RSU01801 1GHz ~ 25GHz Test Setup: FCC ID: 2ABES-ULTRA8 Page Number: 17 of 29

Report No.: 1504RSU01801 7.3.3. Test Result Test Mode: Transmission Test Site: AC1 Test Engineer: Roy Cheng Test Date: 2015.05.18 Remark: Fundamental Radiated Emission Frequency Reading Factor Measure Limit Margin Detector Polarization (MHz) Level (dB) Level (dBμV/m) (dB) (dBμV) (dBμV/m) 62.7 31.2 93.9 114.0 -20.1 PK Horizontal 62.5 31.2 93.7 94.0 -0.3 AV Horizontal 2403 53.6 31.2 84.8 114.0 -29.2 PK Vertical 53.2 31.2 84.4 94.0 -9.6 AV Vertical 61.4 31.2 92.6 114.0 -21.4 PK Horizontal 60.3 31.2 91.5 94.0 -2.5 AV Horizontal 2442 52.9 31.2 84.1 114.0 -29.9 PK Vertical 51.5 31.2 82.7 94.0 -11.3 AV Vertical 61.9 31.2 93.0 114.0 -21.0 PK Horizontal 61.6 31.2 92.8 94.0 -1.2 AV Horizontal 2480 49.2 31.2 80.4 114.0 -33.6 PK Vertical 48.6 31.2 79.8 94.0 -14.2 AV Vertical Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: 2ABES-ULTRA8 Page Number: 18 of 29

Report No.: 1504RSU01801 Test Mode: Transmission Test Site: AC1 Test Engineer: Roy Cheng Test Date: 2015.05.18 Remark: Harmonic Radiated Emission Remark: 1. Average measurement was not performed if peak level lower than average limit. 2. The worst case of Radiated Spurious Emission. 3. Other frequency was 20dB below limit line within 1-18GHz, there is not show in the report. Mark Frequency Reading Factor Measure Limit Margin Detector Polarization (MHz) Level (dB) Level (dBμV/m) (dB) (dBμV) (dBμV/m) 4808.0 38.2 2.7 40.9 74.0 -33.1 PK Horizontal 4808.0 37.9 2.7 40.6 54.0 -13.4 AV Horizontal 4808.0 39.3 2.7 42.0 74.0 -32.0 PK Vertical 4808.0 38.6 2.7 41.3 54.0 -12.7 AV Vertical * 7205.0 39.0 7.8 46.8 74.0 -27.2 PK Horizontal * 7205.5 38.5 7.8 46.3 54.0 -7.7 AV Horizontal * 7213.5 39.6 7.8 47.4 74.0 -26.6 PK Vertical * 7215.0 38.9 7.8 46.7 54.0 -7.3 AV Vertical * 9612.0 35.4 10.9 46.3 74.0 -27.7 PK Horizontal * 9612.3 33.8 10.9 44.7 54.0 -9.3 AV Horizontal * 9612.0 35.4 10.9 46.3 74.0 -27.7 PK Vertical * 9612.5 33.5 10.9 44.4 54.0 -9.6 AV Vertical 12015.0 35.3 11.9 47.2 74.0 -26.8 PK Horizontal 12015.0 34.0 11.9 45.9 54.0 -8.1 AV Horizontal 12015.0 35.2 11.9 47.1 74.0 -26.9 PK Vertical 12015.2 33.7 11.9 45.6 54.0 -8.4 AV Vertical Note 1: “*” is not in restricted band, its limit is 50dBc of the fundamental emission level (93.9dBμV/m) or 15.209 which is higher. Note 2: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB). Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB). FCC ID: 2ABES-ULTRA8 Page Number: 19 of 29

Report No.: 1504RSU01801 Test Mode: Transmission Test Site: AC1 Test Engineer: Roy Cheng Test Date: 2015.05.18 Remark: The worst case of General Radiated Emission Frequency Reading Factor Measure Limit Margin (dB) Detector Polarization (MHz) Level (dB) Level (dBμV/m) (dBμV) (dBμV/m) 398.1 16.0 16.6 32.6 46.0 -13.4 QP Horizontal 475.7 16.2 17.8 34.0 46.0 -12.0 QP Horizontal 216.7 14.8 12.5 27.3 46.0 -18.7 QP Vertical 622.7 15.3 20.2 35.6 46.0 -10.4 QP Vertical 2207.0 42.9 -3.6 39.3 74.0 -34.7 PK Horizontal 3227.0 39.3 -1.6 37.6 74.0 -36.4 PK Horizontal 2241.0 41.4 -3.5 37.9 74.0 -36.1 PK Vertical 3235.5 38.9 -1.7 37.2 74.0 -36.8 PK Vertical Note 1: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre Amplifier Gain (dB) Note 2: The test trace is same as the ambient noise and the amplitude of the emissions are attenuated more than 20dB below the permissible (the test frequency range: 9kHz ~ 30MHz, 18GHz ~ 25GHz), therefore no data appear in the report. FCC ID: 2ABES-ULTRA8 Page Number: 20 of 29

Report No.: 1504RSU01801 7.4. Radiated Outside of The Specified Frequency Bands Measurement 7.4.1. Test Result Site: AC1 Time: 2015/05/19 - 18:52 Limit: FCC_Part15.209_RE(3m) Engineer: Roy Cheng Probe: BBHA9120D_1-18GHz Polarity: Horizontal EUT: Remote Control Power: By Battery Note: Mode 1 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 2355.125 60.082 28.809 -13.918 74.000 31.273 PK 2 2400.000 58.579 27.392 -15.421 74.000 31.187 PK 3 * 2403.195 93.858 62.676 N/A N/A 31.183 PK Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: 2ABES-ULTRA8 Page Number: 21 of 29

Report No.: 1504RSU01801 Site: AC1 Time: 2015/05/19 - 18:58 Limit: FCC_Part15.209_RE(3m) Engineer: Roy Cheng Probe: BBHA9120D_1-18GHz Polarity: Horizontal EUT: Remote Control Power: By Battery Note: Mode 1 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 2355.173 48.221 16.948 -5.779 54.000 31.273 AV 2 2400.000 45.499 14.312 -8.501 54.000 31.187 AV 3 * 2403.052 93.665 62.482 N/A N/A 31.183 AV Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: 2ABES-ULTRA8 Page Number: 22 of 29

Report No.: 1504RSU01801 Site: AC1 Time: 2015/05/19 - 18:59 Limit: FCC_Part15.209_RE(3m) Engineer: Roy Cheng Probe: BBHA9120D_1-18GHz Polarity: Vertical EUT: Remote Control Power: By Battery Note: Mode 1 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 2387.948 59.956 28.749 -14.044 74.000 31.206 PK 2 2400.000 58.849 27.662 -15.151 74.000 31.187 PK 3 * 2403.147 84.763 53.581 N/A N/A 31.183 PK Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: 2ABES-ULTRA8 Page Number: 23 of 29

Report No.: 1504RSU01801 Site: AC1 Time: 2015/05/19 - 19:00 Limit: FCC_Part15.209_RE(3m) Engineer: Roy Cheng Probe: BBHA9120D_1-18GHz Polarity: Vertical EUT: Remote Control Power: By Battery Note: Mode 1 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 2379.397 45.338 14.116 -8.662 54.000 31.222 AV 2 2400.000 45.209 14.022 -8.791 54.000 31.187 AV 3 * 2403.195 84.387 53.205 N/A N/A 31.183 AV Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: 2ABES-ULTRA8 Page Number: 24 of 29

Report No.: 1504RSU01801 Site: AC1 2015/05/19 - 19:02 Limit: FCC_Part15.209_RE(3m) Engineer: Roy Cheng Probe: BBHA9120D_1-18GHz Polarity: Horizontal EUT: Remote Control Power: By Battery Note: Mode 1 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 * 2480.046 93.034 61.850 N/A N/A 31.184 PK 2 2483.500 58.347 27.154 -15.653 74.000 31.194 PK 3 2485.227 60.423 29.225 -13.577 74.000 31.198 PK Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: 2ABES-ULTRA8 Page Number: 25 of 29

Report No.: 1504RSU01801 Site: AC1 Time: 2015/05/19 - 19:06 Limit: FCC_Part15.209_RE(3m) Margin: 0 Probe: BBHA9120D_1-18GHz Polarity: Horizontal EUT: Remote Control Power: By Battery Note: Mode 1 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 * 2480.123 92.827 61.643 N/A N/A 31.185 AV 2 2483.500 45.455 14.262 -8.545 54.000 31.194 AV 3 2492.256 45.659 14.443 -8.341 54.000 31.216 AV Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: 2ABES-ULTRA8 Page Number: 26 of 29

Report No.: 1504RSU01801 Site: AC1 Time: 2015/05/19 - 19:06 Limit: FCC_Part15.209_RE(3m) Margin: 0 Probe: BBHA9120D_1-18GHz Polarity: Vertical EUT: Remote Control Power: By Battery Note: Mode 1 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 * 2480.112 80.425 49.241 N/A N/A 31.184 PK 2 2483.500 57.997 26.804 -16.003 74.000 31.194 PK 3 2484.435 59.548 28.352 -14.452 74.000 31.195 PK Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: 2ABES-ULTRA8 Page Number: 27 of 29

Report No.: 1504RSU01801 Site: AC1 Time: 2015/05/19 - 19:08 Limit: FCC_Part15.209_RE(3m) Engineer: Roy Cheng Probe: BBHA9120D_1-18GHz Polarity: Vertical EUT: Remote Control Power: By Battery Note: Mode 1 No Flag Mark Frequency Measure Reading Over Limit Limit Factor Type (MHz) Level Level (dB) (dBuV/m) (dB) (dBuV/m) (dBuV) 1 * 2480.145 79.828 48.644 N/A N/A 31.185 AV 2 2483.500 45.357 14.164 -8.643 54.000 31.194 AV Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: 2ABES-ULTRA8 Page Number: 28 of 29

Report No.: 1504RSU01801 8. CONCLUSION The data collected relate only the item(s) tested and show that the Remote Control FCC ID: 2ABES-ULTRA8 is in compliance with Part 15C of the FCC Rules. The End FCC ID: 2ABES-ULTRA8 Page Number: 29 of 29


Document Created: 2015-05-26 16:15:26
Document Modified: 2015-05-26 16:15:26
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC