Test Report (JBP)_rev.pdf

FCC ID: 2ABCB-WLU6331

Test Report

Download: PDF
FCCID_2489336

FCC Certification Test Report Report No.: FC141001C29 Test Model: WLU6331 FCC ID: 2ABCB-WLU6331 Received Date: Oct. 01, 2014 Test Date: Oct. 06 ~ Oct. 08, 2014 Issued Date: Nov. 03, 2014 Applicant: Raspberry Pi Trading Ltd Address: Mount Pleasant House Mount Pleasant, Cambridge, Cambridgeshire, CB3 0RN, United Kingdom Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 19, Hwa Ya 2nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: FC141001C29 Page No. 1 / 24 Report Format Version: 6.1.0

Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ......................................................................................................................... 4 2 Summary of Test Results......................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information ................................................................................................................................. 6 3.1 Features of EUT .................................................................................................................................. 6 3.2 General Description of EUT ................................................................................................................ 6 3.3 Operating Modes of EUT and Determination of Worst Case Operating Mode ................................... 6 3.4 Test Program Used and Operation Descriptions................................................................................. 6 3.5 Primary Clock Frequencies of Internal Source ................................................................................... 6 3.6 Miscellaneous...................................................................................................................................... 7 4 Configuration and Connections with EUT ............................................................................................. 8 4.1 Connection Diagram of EUT and Peripheral Devices ......................................................................... 8 4.2 Configuration of Peripheral Devices and Cable Connections ............................................................. 8 5 Conducted Emissions at Mains Ports .................................................................................................... 9 5.1 Limits ................................................................................................................................................... 9 5.2 Test Instruments .................................................................................................................................. 9 5.3 Test Arrangement .............................................................................................................................. 10 5.4 Test Results ........................................................................................................................................ 11 6 Radiated Emissions up to 1 GHz .......................................................................................................... 13 6.1 Limits ................................................................................................................................................. 13 6.2 Test Instruments ................................................................................................................................ 14 6.3 Test Arrangement .............................................................................................................................. 15 6.4 Test Results ....................................................................................................................................... 16 7 Radiated Emissions above 1 GHz......................................................................................................... 18 7.1 Limits ................................................................................................................................................. 18 7.2 Test Instruments ................................................................................................................................ 19 7.3 Test Arrangement .............................................................................................................................. 20 7.4 Test Results ....................................................................................................................................... 21 8 Pictures of Test Arrangements ............................................................................................................. 23 Appendix – Information on the Testing Laboratories ................................................................................ 24 Report No.: FC141001C29 Page No. 2 / 24 Report Format Version: 6.1.0

Release Control Record Issue No. Description Date Issued FC141001C29 Original release. Nov. 03, 2014 Report No.: FC141001C29 Page No. 3 / 24 Report Format Version: 6.1.0

1 Certificate of Conformity Product: WiFi Adapter Brand: Raspberry Pi Test Model: WLU6331 Sample Status: Engineering sample Applicant: Raspberry Pi Trading Ltd Test Date: Oct. 06 ~ Oct. 08, 2014 Standards: 47 CFR FCC Part 15, Subpart B, Class B ICES-003:2012 Issue 5, Class B ANSI C63.4:2009 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : , Date: Nov. 03, 2014 Polly Chien / Specialist Approved by : , Date: Nov. 03, 2014 Ken Liu / Senior Manager Report No.: FC141001C29 Page No. 4 / 24 Report Format Version: 6.1.0

2 Summary of Test Results 47 CFR FCC Part 15, Subpart B / ICES-003:2012 Issue 5, Class B ANSI C63.4:2009 FCC ICES-003 Test Item Result/Remarks Verdict Clause Clause AC Power Line Conducted Minimum passing Class B margin 15.107 6.1 Pass Emissions is -9.57 dB at 0.43906 MHz Radiated Emissions up to 1 Minimum passing Class B margin 6.2.1 Pass GHz is -4.10 dB at 34.97 MHz 15.109 Radiated Emissions above 1 Minimum passing Class B margin 6.2.2 Pass GHz is -23.47 dB at 2597.91 MHz Note: There is no deviation to the applied test methods and requirements covered by the scope of this report. 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT: The listed uncertainties are the worst case uncertainty for the entire range of measurement. Please note that the uncertainty values are provided for informational purposes only and are not used in determining the PASS/FAIL results. Expended Uncertainty Measurement Frequency (k=2) (±) Conducted Emissions at mains ports 150kHz ~ 30MHz 2.44 dB Radiated Emissions up to 1 GHz 30MHz ~ 1GHz 4.70 dB Radiated Emissions above 1 GHz Above 1GHz 2.26 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: FC141001C29 Page No. 5 / 24 Report Format Version: 6.1.0

3 General Information 3.1 Features of EUT The tests reported herein were performed according to the method specified by Raspberry Pi Trading Ltd, for detailed feature description, please refer to the manufacturer's specifications or user's manual. 3.2 General Description of EUT Product WiFi Adapter Brand Raspberry Pi Test Model WLU6331 Sample Status Engineering sample Operating Software NA Power Supply Rating 5Vdc (host equipment) Accessory Device NA Data Cable Supplied NA 3.3 Operating Modes of EUT and Determination of Worst Case Operating Mode The EUT consumes power from host, which designed with AC power supply of rating 100-240Vac, 50/60Hz. For radiated emission evaluation, 230Vac/50Hz (for EN 55022 & AS/NZS CISPR 22) and 120Vac/60Hz (for FCC Part 15) had been covered during the pre-test. The worst data was found at 120Vac/60Hz and recorded in the applied test report. EUT has been pre-tested under following test modes, and test mode 1 was the worst case for final test. Mode Test Condition 1 2.4G link, 120Vac/60Hz 2 2.4G link, 230Vac/50Hz 3 2.4G idle, 120Vac/60Hz Test modes are presented in the report as below. Mode Test Condition Conducted emission test - 2.4G link Radiated emission test - 2.4G link 3.4 Test Program Used and Operation Descriptions a. Plugged EUT into the notebook and placed on the testing table. b. The notebook sent “H” patterns to the screen and displayed them. c. The notebook sent “H” patterns to the printer and the printer printed them. d. The notebook read and wrote with the floppy. e. The notebook linked with the wireless router via the EUT. f. Steps b~e were repeated. 3.5 Primary Clock Frequencies of Internal Source The highest frequency generated or used within the EUT or on which the EUT operates or tunes is 2.4 GHz provided by Raspberry Pi Trading Ltd, for detailed internal source, please refer to the manufacturer's specifications. Report No.: FC141001C29 Page No. 6 / 24 Report Format Version: 6.1.0

3.6 Miscellaneous Labelling Requirements for Part 15 Devices:  Verification The specific labelling requirements for a device subject to the Verification procedure are contained in Section 15.19(a). These labelling requirements are: If the device is subject only to Verification, include a label bearing a unique identifier (Section 2.954) and one of three compliance statements specified in Section 15.19(a). If the labeling area for the device is so small, and/or it is not practical to place the compliance statement on the device, then the statement can be placed in the user manual or product packaging (Section 15.19(a)(5)). However, the device must still be labelled with the unique identifier (Verification). Generally, devices smaller than the palm of the hand are considered too small for the compliance statement.  Certification If the device is subject to Certification: (1) Section 2.925 contains information on identification of the equipment; (2) include a label bearing an FCC Identifier (FCC ID) (Section 2.926) and (3) include the appropriate compliance statement in Section 15.19(a). If the device is considered too small and therefore it is impractical (smaller than the palm of the hand) to display the compliance statement, then the statement may be placed in the user manual or product packaging. However, the device must still be labelled with the FCC ID. If the device is unquestionably too small for the FCC ID to be readable (smaller than 4-6 points), the FCC ID may be placed in the user manual. However, it must be determined that the device itself is too small – the label area allocated to the FCC ID may not be reduced because of over crowded identification of other product and regulatory information. An electronic display of the FCC ID (see 9. Electronic Labelling below) may be used for Certification of Section 15.212 modular transmitters and software defined radios (Section 2.944).  Declaration of Conformity (DoC): The labelling requirements for a device subject to the DoC procedure are specified in Section 15.19(b). The label should include the FCC logo along with the Trade Name and Model Number, which satisfies the unique identifier requirement of Section 2.1074 if it represents the identical equipment tested for DoC compliance. For personal computers assembled from authorized components, the following additional text must also be included: “Assembled from tested components,” “Complete system not tested.” When the device is so small and/or when it is not practical to place the required additional text on the device, the text may be placed in the user manual or pamphlet supplied to the user. However, the FCC logo, Trade Name, and Model Number must still be displayed on the device (Section 15.19(b)(3)). Part 15 Declaration of Conformity (DoC) Label Examples Equipment certified as software defined radio may use a means that readily displays the FCC ID on an electronic display screen, instead of labelling the device (Section 2.925 (e)). Further information may refer to FCC KDB:784748 D01 Labelling Part 15 &18 Guidelines Labelling Requirements for ICES-003 Devices:  Industry Canada ICES-003 Compliance Label: CAN ICES-3 (*)/NMB-3(*) * Insert either “A” or “B” but not both to identify the applicable Class of ITE. Report No.: FC141001C29 Page No. 7 / 24 Report Format Version: 6.1.0

4 Configuration and Connections with EUT 4.1 Connection Diagram of EUT and Peripheral Devices Notebook (A) EUT (1) (2) Printer (B) Floppy (C) Remote site Wireless N Dual band Router (D) 4.2 Configuration of Peripheral Devices and Cable Connections ID Product Brand Model No. Serial No. FCC ID Remarks A. Notebook DELL Latitude E6420 HPFC5Q1 FCC DoC Approved - B. Printer EPSON T22 MEEZ070388 FCC DoC Approved - External USB 1.1 C. SONY MPF82E 50010254 FCC DoC Approved - Floppy Wireless N Dual D. D-LINK DIR-815 PVK21B5000399 KA21R815A1 - band Router Note: 1. All power cords of the above support units are non-shielded (1.8m). 2. Item D acted as a communication partner to transfer data. Shielding ID Descriptions Qty. Length (m) Cores (Qty.) Remarks (Yes/No) 1. USB 1 1.8 Y 0 - 2. USB 1 0.5 Y 1 - Note: The core(s) is(are) originally attached to the cable(s). Report No.: FC141001C29 Page No. 8 / 24 Report Format Version: 6.1.0

5 Conducted Emissions at Mains Ports 5.1 Limits Class A (dBuV) Class B (dBuV) Frequency (MHz) Quasi-peak Average Quasi-peak Average 0.15 - 0.5 79 66 66 - 56 56 - 46 0.50 - 5.0 73 60 56 46 5.0 - 30.0 73 60 60 50 Notes: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases linearly with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 5.2 Test Instruments Description & Model No. Serial No. Cal. Date Cal. Due Manufacturer Test Receiver ESCS30 100288 Apr. 24, 2014 Apr. 23, 2015 ROHDE & SCHWARZ RF signal cable 5D-FB Cable-HYCO2-01 Dec. 27, 2013 Dec. 26, 2014 Woken LISN ROHDE & SCHWARZ ESH2-Z5 100100 Dec. 23, 2013 Dec. 22, 2014 (EUT) LISN ROHDE & SCHWARZ ESH3-Z5 100312 Jul. 10, 2014 Jul. 09, 2015 (Peripheral) Software BV ADT_Cond_ NA NA NA ADT V7.3.7.3 Notes: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 2. 3. The VCCI Site Registration No. is C-2047. Report No.: FC141001C29 Page No. 9 / 24 Report Format Version: 6.1.0

5.3 Test Arrangement a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The test results of conducted emissions at mains ports are recorded of six worst margins for quasi-peak (mandatory) [and average (if necessary)] values against the limits at frequencies of interest unless the margin is 20 dB or greater. Note: The resolution bandwidth and video bandwidth of test receiver is 9kHz for quasi-peak detection (QP) and average detection (AV) at frequency 0.15MHz-30MHz. V e r tic a l G r o u n d R e fe r e n c e P la n e T e s t R e c e iv e r EUT 40cm 80cm L IS N H o r iz o n ta l G r o u n d R e f e r e n c e P la n e N o t e : 1 .S u p p o r t u n i ts w e r e c o n n e c t e d t o s e c o n d L IS N . 2 . B o t h o f L I S N s ( A M N ) a r e 8 0 c m f r o m E U T a n d a t le a s t 8 0 c m f r o m o t h e r u n its a n d o t h e r m e ta l p l a n e s Report No.: FC141001C29 Page No. 10 / 24 Report Format Version: 6.1.0

5.4 Test Results Detector Function & ; Frequency Range 150kHz ~ 3OMHz Resolution Quasi—Peak (QP) / — Average (AV), OkHz Bandwidth Environmental s Input Power 120Vac, 60Hz (System) Conditions 23°C , 66%RH Tested by Mick Chou Test Date 2014/10/6 Phase Of Power: Line (L) Frequency |Correction| Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) QP. AV. QP. AV. QP. AV. QP. AV. 1 0.34141 0.29 33.90 3243 34.19 32.72 §9.17 49.17 —24.97 —16.44 2 0.44297 0.30 39.13 34.16 39.43 34.46 57.01 47.01 —17.57 —12.54 3 0.54453 0.31 28.07 19.35 28.38 19.66 56.00 46.00 —27.62 —26.34 4 0.86484 0.33 3248 23.40 32.81 23.73 56.00 46.00 —23.19 —22.27 5 1.13281 0.34 2948 22.57 29.82 22.91 56.00 46.00 —26.18 —23.09 6 2.02734 0.36 32.82 26.99 33.18 27.35 56.00 46.00 —22.82 —18.65 Remarks: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value aoue no— Prmase > 100— or uime L so— cartine L ols the who sube ie Report No.: FC141001C29 Page No. 11 / 24 Report Format Version: 6.1.0

Detector Function & ; Frequency Range 150kHz ~ 3OMHz Resolution Quasi—Peak (QP) / — Average (AV), OkHz Bandwidth Environmental s Input Power 120Vac, 60Hz (System) Conditions 23°C , 66%RH Tested by Mick Chou Test Date 2014/10/6 Phase Of Power: Neutral (N) Frequency |Correction| Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) QP. AV. QP. AV. QP. AV. QP. AV. 1 0.23594 0.28 33.59 25.13 33.87 25.41 6224 52.24 —28.36 —26.82 2 0.39609 0.30 39.47 37.60 39.77 37.90 57.93 47.93 —18.17 —10.04 3 0.43906 0.30 38.10 37.21 38.40 37.51 57.08 47.08 —18.68 —9.57 4 0.48203 0.31 32.28 23.71 3259 24.02 56.30 46.30 —23.72 —22.29 5 2.07813 0.37 33.71 27.15 34.08 27.52 56.00 46.00 —21.92 —18.48 6 242188 0.38 30.45 25.34 30.83 25.72 56.00 46.00 —25.17 —20.28 Remarks: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value aoue no— Prmase > 100— or uime L so— cartine L ols the who sube ie Report No.: FC141001C29 Page No. 12/ 24 Report Format Version: 6.1.0

6 Radiated Emissions up to 1 GHz 6.1 Limits Emissions radiated outside of the specified bands, shall be according to the general radiated limits as following: Radiated Emissions Limits at 10 meters (dBμV/m) Frequencies FCC 15B / ICES-003, FCC 15B / ICES-003, CISPR 22, Class A CISPR 22, Class B (MHz) Class A Class B 30-88 39 29.5 88-216 43.5 33.1 40 30 216-230 46.4 35.6 230-960 47 37 960-1000 49.5 43.5 Radiated Emissions Limits at 3 meters (dBμV/m) Frequencies FCC 15B / ICES-003, FCC 15B / ICES-003, CISPR 22, Class A CISPR 22, Class B (MHz) Class A Class B 30-88 49.5 40 88-216 54 43.5 50.5 40.5 216-230 56.9 46 230-960 57.5 47.5 960-1000 60 54 Notes: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. QP detector shall be applied if not specified. Report No.: FC141001C29 Page No. 13 / 24 Report Format Version: 6.1.0

6.2 Test Instruments Description & Model No. Serial No. Cal. Date Cal. Due Manufacturer Test Receiver ESR-7 101240 Sep. 29, 2014 Sep. 28, 2015 ROHDE & SCHWARZ (V) Test Receiver ESR-7 101264 Nov. 29, 2013 Nov. 28, 2014 ROHDE & SCHWARZ (H) BILOG Antenna VULB9168 9168-148 Feb. 25, 2014 Feb. 24, 2015 SCHWARZBECK (V) BILOG Antenna VULB9168 9168-149 Feb. 25, 2014 Feb. 24, 2015 SCHWARZBECK (H) Preamplifier 8447D 2944A10636 Oct. 18, 2013 Oct. 17, 2014 Agilent (V) Preamplifier 8447D 2944A10637 Oct. 18, 2013 Oct. 17, 2014 Agilent (H) Preamplifier 8449B 3008A01959 Oct. 18, 2013 Oct. 17, 2014 Agilent RF signal cable 8D-FB Cable-Hych1-01 Oct. 26, 2013 Oct. 25, 2014 Woken (V) RF signal cable 8D-FB Cable-Hych1-02 Oct. 26, 2013 Oct. 25, 2014 Woken (H) Software BV ADT_Radiated_ NA NA NA BV ADT V 8.7.07 Antenna Tower (V) MFA-440 9707 NA NA Antenna Tower (H) MFA-440 970705 NA NA Turn Table DS430 50303 NA NA Controller (V) MF7802 074 NA NA Controller (H) MF7802 08093 NA NA Notes: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Chamber 1. 3. The FCC Site Registration No. is 477732. 4. The IC Site Registration No. is IC 7450F-1. 5. The VCCI Site Registration No. is R-1893. Report No.: FC141001C29 Page No. 14 / 24 Report Format Version: 6.1.0

6.3 Test Arrangement a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at an accredited test facility. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 10 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. Note: The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for quasi-peak detection (QP) at frequency below 1GHz. Report No.: FC141001C29 Page No. 15 / 24 Report Format Version: 6.1.0

6.4 Test Results Detector Function & Frequency Range 30MHz ~ 1GHz Resolution Quasi-Peak (QP), 120kHz Bandwidth Environmental 23℃, 67%RH Test Date 2014/10/7 Conditions Tested by Daniel Lin Antenna Polarity & Test Distance : Horizontal at 10 m Emission Antenna Table Raw Correction Frequency Limit Margin No Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 46.98 14.38 QP 30.00 -15.62 1.50 H 122 29.09 -14.71 2 166.58 19.86 QP 30.00 -10.14 4.00 H 161 34.13 -14.27 3 209.90 23.35 QP 30.00 -6.65 3.50 H 343 40.01 -16.66 4 278.87 24.20 QP 37.00 -12.80 3.00 H 298 36.94 -12.74 5 349.53 26.46 QP 37.00 -10.54 2.50 H 221 37.22 -10.76 6 383.39 22.81 QP 37.00 -14.19 2.00 H 15 32.54 -9.73 7 439.99 20.72 QP 37.00 -16.28 3.00 H 176 29.19 -8.47 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) – Pre-Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value Report No.: FC141001C29 Page No. 16 / 24 Report Format Version: 6.1.0

Detector Function & Frequency Range 30MHz ~ 1GHz Resolution Quasi-Peak (QP), 120kHz Bandwidth Environmental 23℃, 67%RH Test Date 2014/10/7 Conditions Tested by Daniel Lin Antenna Polarity & Test Distance : Vertical at 10 m Emission Antenna Table Raw Correction Frequency Limit Margin No Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 34.97 25.90 QP 30.00 -4.10 1.50 V 148 41.12 -15.22 2 44.70 23.70 QP 30.00 -6.30 3.00 V 204 37.81 -14.11 3 149.22 25.78 QP 30.00 -4.22 1.50 V 2 39.32 -13.54 4 166.58 24.96 QP 30.00 -5.04 1.50 V 81 38.50 -13.54 5 279.64 23.64 QP 37.00 -13.36 1.00 V 140 35.44 -11.80 6 439.99 24.40 QP 37.00 -12.60 3.00 V 143 32.40 -8.00 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) – Pre-Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value Report No.: FC141001C29 Page No. 17 / 24 Report Format Version: 6.1.0

7 Radiated Emissions above 1 GHz 7.1 Limits Emissions radiated outside of the specified bands, shall be according to the general radiated limits as following: Radiated Emissions Limits at 10 meters (dBμV/m) Frequencies FCC 15B / ICES-003, FCC 15B / ICES-003, CISPR 22, Class A CISPR 22, Class B (MHz) Class A Class B 1000-3000 Avg: 49.5 Avg: 43.5 Not defined Not defined Above 3000 Peak: 69.5 Peak: 63.5 Not defined Not defined Radiated Emissions Limits at 3 meters (dBμV/m) Frequencies FCC 15B / ICES-003, FCC 15B / ICES-003, CISPR 22, Class A CISPR 22, Class B (MHz) Class A Class B Avg: 56 Avg: 50 1000-3000 Avg: 60 Avg: 54 Peak: 76 Peak: 70 Peak: 80 Peak: 74 Avg: 60 Avg: 54 Above 3000 Peak: 80 Peak: 74 Notes: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Frequency Range (For unintentional radiators) Highest frequency generated or used in the device or Upper frequency of measurement range (MHz) on which the device operates or tunes (MHz) Below 1.705 30 1.705-108 1000 108-500 2000 500-1000 5000 5th harmonic of the highest frequency or 40GHz, Above 1000 whichever is lower Report No.: FC141001C29 Page No. 18 / 24 Report Format Version: 6.1.0

7.2 Test Instruments Description & Model No. Serial No. Cal. Date Cal. Due Manufacturer Test Receiver ESCI 100613 Oct. 24, 2013 Oct. 23, 2014 ROHDE & SCHWARZ Spectrum Analyzer E4446A MY44360124 Feb. 12, 2014 Feb. 11, 2015 Agilent BILOG Antenna VULB9168 9168-157 Feb. 26, 2014 Feb. 25, 2015 SCHWARZBECK RF signal cable 8D-FB NA Mar. 21, 2014 Mar. 20, 2015 Woken HORN Antenna BBHA 9120 D 9120D-404 Jan. 05, 2014 Jan. 04, 2015 SCHWARZBECK Preamplifier Agilent 8447D 2944A10629 Oct. 18, 2013 Oct. 17, 2014 (Below 1GHz) Preamplifier Agilent 8449B 3008A01959 Oct. 18, 2013 Oct. 17, 2014 (Above 1GHz) RF signal cable MWX322+MWX2211308 SUCOFLEX 104 Nov. 07, 2013 Nov. 06, 2014 HUBER+SUHNER S0295 Software BV ADT_Radiated_ NA NA NA BV ADT V7.6.15.9.4 Antenna Tower AT100 AT93021702 NA NA BV ADT Turn Table TT100 TT93021702 NA NA BV ADT Controller SC100 SC93021702 NA NA BV ADT HORN Antenna BBHA 9170 BBHA9170243 Jan. 09, 2014 Jan. 08, 2015 SCHWARZBECK RF signal cable 38218/2+ SUCOFLEX 102 Oct. 26, 2013 Oct. 25, 2014 HUBER+SUHNNER 37433/2 Fix tool for Boresight BAF-01 2 NA NA antenna tower Notes: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Chamber 2. 3. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 4. The FCC Site Registration No. is 686814. 5. The IC Site Registration No. is IC 7450F-2. 6. The VCCI Site Registration No. is G-18. Report No.: FC141001C29 Page No. 19 / 24 Report Format Version: 6.1.0

7.3 Test Arrangement a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at an accredited chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna can be varied from one meter to four meters, the height of adjustment depends on the EUT height and the antenna 3dB beamwidth both, to detect the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The spectrum analyzer system was set to peak and average detect function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. Note: The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth is 3MHz for Peak detection (PK) at frequency above 1GHz. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz for Average detection (AV) at frequency above 1GHz. Report No.: FC141001C29 Page No. 20 / 24 Report Format Version: 6.1.0

7.4 Test Results Detector Function & Peak (PK) / Frequency Range 1GHz ~ 18GHz Resolution Average (AV), 1MHz Bandwidth Environmental Input Power 120Vac, 60Hz (System) 22℃, 62%RH Conditions Tested by Rolan Zheng Test Date 2014/10/8 Antenna Polarity & Test Distance : Horizontal at 3 m Emission Antenna Table Raw Correction Frequency Limit Margin No Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1614.34 41.55 PK 74.00 -32.45 1.72 H 211 48.32 -6.77 2 1614.34 27.77 AV 54.00 -26.23 1.72 H 211 34.54 -6.77 3 2010.38 41.51 PK 74.00 -32.49 1.32 H 267 47.08 -5.57 4 2010.38 27.84 AV 54.00 -26.16 1.32 H 267 33.41 -5.57 5 2890.11 42.56 PK 74.00 -31.44 1.30 H 95 45.17 -2.61 6 2890.11 26.39 AV 54.00 -27.61 1.30 H 95 29.00 -2.61 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) – Pre-Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value Report No.: FC141001C29 Page No. 21 / 24 Report Format Version: 6.1.0

Detector Function & Peak (PK) / Frequency Range 1GHz ~ 18GHz Resolution Average (AV), 1MHz Bandwidth Environmental Input Power 120Vac, 60Hz (System) 22℃, 62%RH Conditions Tested by Rolan Zheng Test Date 2014/10/8 Antenna Polarity & Test Distance : Vertical at 3 m Emission Antenna Table Raw Correction Frequency Limit Margin No Level Height Angle Value Factor (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1635.96 41.63 PK 74.00 -32.37 1.22 V 284 48.34 -6.71 2 1635.96 24.58 AV 54.00 -29.42 1.22 V 284 31.29 -6.71 3 2345.23 43.41 PK 74.00 -30.59 1.00 V 261 47.62 -4.21 4 2345.23 27.41 AV 54.00 -26.59 1.00 V 261 31.62 -4.21 5 2597.91 44.72 PK 74.00 -29.28 1.24 V 138 48.08 -3.36 6 2597.91 30.53 AV 54.00 -23.47 1.24 V 138 33.89 -3.36 Remarks: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) – Pre-Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value Report No.: FC141001C29 Page No. 22 / 24 Report Format Version: 6.1.0

8 Pictures of Test Arrangements Please refer to the attached file (Test Setup Photo). Report No.: FC141001C29 Page No. 23 / 24 Report Format Version: 6.1.0

Appendix – Information on the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-5935343 Fax: 886-2-26051924 Fax: 886-3-5935342 Hwa Ya EMC/RF/Safety Lab Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: FC141001C29 Page No. 24 / 24 Report Format Version: 6.1.0


Document Created: 2019-09-28 14:48:31
Document Modified: 2019-09-28 14:48:31
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC