User Manual 2

FCC ID: 2ABCB-RPI21

Users Manual

Download: PDF
FCCID_2205294

Raspberry Pi Regulatory Compliance and Safety Information Product Name: Raspberry Pi Model B IMPORTANT: PLEASE RETAIN THIS INFORMATION FOR FUTURE REFERENCE For full set up and installation instructions please visit http://www.raspberrypi.org/qsg Warnings n This product shall only be connected to an external power supply rated at 5V dc, and a minimum current of 700-1200mA. Any external power supply used with the Raspberry-Pi shall comply with relevant regulations and standards applicable in the country of intended use. n This product should not be overclocked as this may make certain components very hot. n This product should be operated in a well ventilated environment and the case should not be covered. n This product should be placed on a stable, flat, non-conductive surface in use and should not be contacted by conductive items. n The connection of unapproved devices to the GPIO connector may affect compliance or result in damage to the unit and invalidate the warranty. n All peripherals used with the Raspberry Pi should comply with relevant standards for the country of use and be marked accordingly to ensure that safety and performance requirements are met. These articles include but are not limited to keyboards, monitors, and mice used in conjunction with the Raspberry Pi. n Where peripherals are connected that do not include the cable or connector, the cable or connector used must offer adequate insulation and operation in order that the requirements of the relevant performance and safety requirements are met. Instructions for safe use To avoid malfunction or damage to your Raspberry Pi please observe the following: n Do not expose it to water, moisture or place on a conductive surface whilst in operation. n Do not expose it to heat from any source; the Raspberry Pi is designed for reliable operation at normal ambient room temperatures. n Take care whilst handling to avoid mechanical or electrical damage to the printed circuit board and connectors. n Avoid handling the printed circuit board while it is powered. Only handle by the edges to minimise the risk of electrostatic discharge damage. n The Raspberry Pi is not designed to be powered from a USB port on other connected equipment, if this is attempted it may malfunction. P Safety Leaflet A6 v1.5.indd 1 03/02/2014 14:25

Compliance Information The Raspberry Pi complies with the relevant provisions of the RoHS Directive for the European Union. In common with all Electrical and Electronic Equipment (EEE) the Raspberry Pi should not be disposed of as household waste. Alternative arrangements may apply in other jurisdictions. Electromagnetic Compatibility AND OPERATION n This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. n This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to the European Standard EN 55022. n This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. n NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ❍❍ Reorient or relocate the receiving antenna ❍❍ Increase the separation between the equipment and receiver ❍❍ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected ❍❍ Consult the dealer or an experienced radio/TV technician for help n This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. n WARNING: Please do not alter or modify the design of this product, doing so may void your ability to use the product freely, this includes altering the frequency at which the product operates. This product is licensed under the MPEG-4 Visual Patent Portfolio License for the personal and non-commercial use of a consumer for (i) encoding video in compliance with the MPEG-4 Visual Standard (“MPEG-4 Video”) and/ or (ii) decoding MPEG-4 Video that was encoded by a consumer engaged in a personal and non-commercial activity and/or was obtained from a video provider licensed by MPEG LA to provide MPEG-4 Video. No license is granted or shall be implied for any other use. Additional information including that relating to promotional, internal and commercial uses and licensing may be obtained from MPEG LA, LLC. See http://www.mpegla.com. This product is licensed under the AVC Patent Portfolio License for the personal use of a consumer or other uses in which it does not receive remuneration to (i) encode video in compliance with the AVC Standard (“AVC Video”) and/or (ii) decode AVC Video that was encoded by a consumer engaged in a personal activity and/or was obtained from a video provider licensed to provide AVC Video. No license is granted or shall be implied for any other use Additional information may be obtained from MPEG LA, LLC. See http://www.mpegla.com N2272 Raspberry Pi is a trademark of the Raspberry Pi Foundation www.element14.com/legislation www.raspberrypi.org Newark element14, 4801 North Ravenswood Avenue, Chicago IL 60640 USA Premier Farnell UK, 150 Armley Road, Leeds LS12 2QQ, United Kingdom Revision 1.5 February 2014 P Safety Leaflet A6 v1.5.indd 2 03/02/2014 14:25


Document Created: 2014-02-03 14:25:48
Document Modified: 2014-02-03 14:25:48
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC