User Manual

FCC ID: 2AB7X-WISECUBE

Users Manual

Download: PDF
FCCID_4081295

Package Contents STEP 2 OTA Temper Self Check Interity Fail Search for Cube on smartphone/tablet. Bluetooth ON Device X1 Search Cube ** Please ensure that the Bluetooth® function of your USB cable X1 smartphone/tablet is ‘ON’ before device pairing. Quick start guide X1 WiseCube FLASHING second and FLASHING first First and last Advanced mPOS Design Integrating Bluetooth® third light alternatively and last red light red light ON EMV and NFC Card Reading Functions Application Download & Installation STEP 3 Battery Charging Status This device can support iOS and Android. Enter bluetooth pin on smartphone/tablet. 1. Please download the official application from app stores before operation. Enter ** Default bluetooth pin is printed on the back of Cube. 2. Please follow app instructions to register and login for proper operation. Bluetooth Pin 3. For any questions, please contact the official application developer or solution provider. After device is successfully paired, Cube is ready to use. 0-10% 11-25% FLASHING first red light FLASHING first light Quick Start Procedures Supported Operating System: iOS, Android Now, you can follow the application instructions to start the transaction process, www.bbpos.com then insert or tap card to complete the Connect the USB Type-C charging cable to charge the transaction. device as shown to the right. APP DOWNLOAD ** If you are paying using an EMV card, please ensure that the EMV chip of the card is facing the right direction. If you are Download the official application from APP Store or Google paying using an NFC card, please ensure you tap the NFC 26-50% 51-79% 80-100% Index & Accessories (Fig.1) Play Store. payment card or your device with your NFC wallet within 4cm range on top of the NFC marking. FLASHING second light FLASHING third light FLASHING last light ** Cube is powered by an internal Lithium Polymer rechargeable battery pack that cannot be removed or replaced. Before first use, charging is required for EMV card reader approximately two to three hours. To prevent potential electrical damage to Battery Level LED status indicator the Cube, it is recommended to use the USB Type-C cable provided with the When power on, it is shown as below in first four second packaging.** NFC card reader LED Status Indicators Power On Power Off Idle 0% 0-10% 11-25% Bluetooth Pairing FLASHING first red light First red light ON First light ON STEP 1 Reset button Press power button to turn on Cube. Show battery level No action needed No light status Power (**please use paper button clip for reset) for 4 seconds to power off USB Type-C port for charging 26-50% 51-79% 80-100% Two lights ON Three lights ON All lights ON

LED Status Indicators Cautions & Important Notes Troubleshooting Warranty NFC Operation • Ensure the device is fully charged before use. Problems Recommendations • Any damage or defects caused by a failure to follow the instructions which relate to this device or as the result of an accident, abuse, misuse, misapplication, product modification, improper voltage • Please ensure the EMV chip of the card is facing the right direction when inserting card. Device cannot be paired • Please press the power on button to restart your device. or current, acts of God, shipping damages or loss, or damage caused by service performed by Ready for Transaction Reading Card Information Card Reading Process • Please check to see if you can find the device’s “Serial Number” (Shown • The NFC card or mobile wallet should be tapped within 4 cm range on top of the reader mark. anyone other than our company are expressly excluded from the warranty stated below. Successfully Completed on the back of device) in the “Scanned Device List” of your smartphone or • Don’t drop, disassemble, tear, open, crush, bend, deform, puncture, shred, microwave, incinerate, • We are not under any obligation to support the device for all operating environments, including tablet. but not limited to, interoperability with all current and/ or future versions of software or paint or insert foreign object into the device. Doing any of which will damage the device and Device loses the connection • Please press the power on button to turn on the device again. The device hardware. void the Warranty. with your smartphone or will automatically connect with your smartphone or tablet again. • Please contact the dealer for any warranty or customer support services. Any repair of the device • Don’t immerse the device into water and place near washbasins or any wet locations. Don’t spill tablet when the device has • The device may be at lower battery level, please use the USB cable to by yourself will void the Warranty. food or liquid on the devices. Don’t attempt to dry the device with external heat sources, such as gone into auto-off mode. recharge it, then retry. microwave or hair dryer. Don’t use any corrosive solvent or water to clean the device. We • Please ensure the device or smartphone/tablet is within the reception range. recommend using dry cloth to clean the surface only. Device does not work with • Please ensure the Bluetooth® function of your smartphone or tablet is FCC Caution Statements: • Don’t use any sharp tools to probe the internal components, connectors or contacts, doing your phone or tablet turned on. First light ON Lights COME ON in All lights ON with • Please check the version of your operating system is supported for this consecutive order “BEEP” sound which may lead to device malfunction and void the Warranty simultaneously. device’s operation. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two Device cannot read your • Please press the power on button to turn on the device again. The device conditions: (1) This device may not cause harmful interference, and (2) this device must accept card successfully will automatically connect with your smartphone or tablet again. any interference received, including interference that may cause undesired operation. EMV Operation • The device may be at lower battery level, please use the USB cable to NOTE: This equipment has been tested and found to comply with the limits for a Class B digital recharge it, then retry. device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable Ready for Transaction When Card is Inserted Card Removal Detection • Please ensure the device or smartphone/tablet is within the reception Product Specifications range. protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the Inserting card instructions, may cause harmful interference to radio communications. However, there is no • Please check if the device has power when operating and ensure devices guarantee that interference will not occur in a particular installation. If this equipment does Functions • EMV chip card reader (ISO 7816 compliant class A, B, C card) are connected. cause harmful interference to radio or television reception, which can be determined by turning • NFC Card Reader (EMV contactless, ISO 14443A/B) • Please follow the application instruction to insert or tap card. the equipment off and on, the user is encouraged to try to correct the interference by one of the • Please ensure that there is no obstacle in the card slots. following measures: • Over-the-air firmware update • Please check if the chip of the card is facing the right direction when • Over-the-air key update inserting card. - Reorient or relocate the receiving antenna. Communication Interface Bluetooth® 4.2 BLE • Please ensure that your phone/ tablet is a supported model for this - Increase the separation between the equipment and receiver. First light ON Lights COME ON Leave all lights ON - Connect the equipment into an outlet on a circuit different from that to which the receiver is Power & Battery Lithium polymer rechargeable battery 500mAh, 3.7V device’s operation. in consecutive order until card is removed • Please insert card with a more constant speed. connected. Charging Via USB Type-C - Consult the dealer or an experienced radio/TV technician for help. Key Management DUKPT, MK/SK Tap Card/Mobile Wallet • Please check if your card supports NFC payment. Caution: Any changes or modifications not expressly approved by the party responsible for Transaction Result Encryption Algorithm TDES • Please ensure if your card is placed within 4 cm range on top of the NFC Support Operating System Android 4.2 or above, iOS (iPhone 6s or above, iPad Air 2 above, compliance could void the user's authority to operate this equipment. marking. Transaction Approved Transaction Failed/Error iPad Mini 5 or above, iPad Pro except 2016 version) • Please take out your NFC payment card from wallet or purse for payment This transmitter must not be co-located or operating in conjunction with any other antenna or Product Size 82.5 x 69.0 x 10.5mm (approx.) to avoid any interference. transmitter. Product Weight 75g (approx.) Device has no response • Please use a paper clip to press the reset button at the bottom for reboot. Operating Temperature 0°C – 45°C (32°F – 113°F) This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 Operating Humidity Max 95% centimetres between the radiator and your body. Storage Temperature -20°C – 55°C (-4°F – 131°F) Storage Humidity Max 95% “BEEP” sound and FLASHING all lights 3 times Two “BEEPS” sound and first red light ON Bluetooth Connection Need Help? Waiting for Connection Connected Bluetooth No Connection Reset Bluetooth E: sales@bbpos.com | T: +852 3158 2585 Room 1903-04, 19/F, Tower 2, Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, Hong Kong www.bbpos.com ©2018 BBPOS Limited. All rights reserved. BBPOS are either trademark or registered trademarks of BBPOS Limited. iOS is the trademark of Apple Inc. Android™ is a trademark of Google Inc. Windows® is registered trademark of Microsoft Corporation in the Lights COME ON Flashing all lights 3 times Power off completely Long press for United States and/or other countries. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, in consecutive order *Power Off completely when 5 minutes 4 seconds and release Inc. and any use of such marks by BBPOS Limited is under license. Other trademarks and trade names are those of their respective after 3 hours of inactivity without any connection power button owners.All details are subject to change without prior notice. Revise v.1 / 20180509


Document Created: 2018-08-09 14:33:53
Document Modified: 2018-08-09 14:33:53
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC