Test Report

FCC ID: 2AB7K-A7910

Test Report

Download: PDF
FCCID_2467759

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 1 of 31 Report No.: R011409364E FCC TEST REPORT for Anker Technology Co., Limited Bluetooth Speaker Model No.: A7910 Prepared for : Anker Technology Co., Limited Address : Room 1318-19, Hollywood Commercial Center, 610 Nathan Road, Mongkok, Kowloon, Hongkong Prepared By : Shenzhen Anbotek Compliance Laboratory Limited Address : 1/F., Building 1, SEC Industrial Park, No.0409 Qianhai Road, Nanshan District, Shenzhen, Guangdong, China Tel: (86) 755-26066544 Fax: (86) 755-26014772 Report Number : R011409364E Date of Test : Sept. 26~ Nov. 11, 2014 Date of Report : Nov. 18, 2014 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 2 of 31 Report No.: R011409364E TABLE OF CONTENTS Description Page Test Report 1. GENERAL INFORMATION......................................................................................................4 1.1. Description of Device (EUT)................................................................................................................4 1.2. Auxiliary Equipment Used during Test................................................................................................ 5 1.3. Description of Test Facility.................................................................................................................. 5 1.4. Measurement Uncertainty..................................................................................................................... 5 2. TEST PROCEDURE....................................................................................................................6 3. CONDUCTED LIMITS............................................................................................................... 7 3.1. Block Diagram of Test Setup................................................................................................................7 3.2. Power Line Conducted Emission Measurement Limits (15.207)......................................................... 7 3.3. Configuration of EUT on Measurement............................................................................................... 7 3.4. Operating Condition of EUT................................................................................................................ 7 3.5. Test Procedure...................................................................................................................................... 8 3.6. Power Line Conducted Emission Measurement Results...................................................................... 8 4. RADIATION INTERFERENCE.............................................................................................. 11 4.1. Requirements (15.249, 15.209):..........................................................................................................11 4.2. Test Procedure.................................................................................................................................... 11 4.3. Test Configuration:............................................................................................................................. 12 4.4. Test Results.........................................................................................................................................13 5. OCCUPIED BANDWIDTH...................................................................................................... 19 5.1. Requirements (15.249):.......................................................................................................................19 5.2. Test Procedure.................................................................................................................................... 19 5.3. Test Configuration:............................................................................................................................. 19 5.4. Test Results.........................................................................................................................................19 6. PHOTOGRAPH......................................................................................................................... 23 6.1. Photo of Conducted Emission Test.....................................................................................................23 6.2. Photo of Radiation Emission Test.......................................................................................................23 APPENDIX I (EXTERNAL PHOTOS)........................................................................................25 APPENDIX II(INTERNAL PHOTOS)........................................................................................ 28 Appendix I (3 Pages) Appendix II (4 Pages) Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 3 of 31 Report No.: R011409364E TEST REPORT Applicant : Anker Technology Co., Limited Manufacturer : Anker Technology Co., Limited EUT : Bluetooth Speaker Model No. : A7910 Serial No. : N.A. Trade Mark : Anker Rating : DC 5V, 1A Measurement Procedure Used: FCC Part15 Subpart C, Paragraph 15.207, 15.249 & 15.209 The device described above is tested by Shenzhen Anbotek Compliance Laboratory Limited to determine the maximum emission levels emanating from the device and the severe levels of the device can endure and its performance criterion. The measurement results are contained in this test report and Shenzhen Anbotek Compliance Laboratory Limited is assumed full of responsibility for the accuracy and completeness of these measurements. Also, this report shows that the EUT (Equipment Under Test) is technically compliant with the FCC Part 15 Subpart C requirements. This report applies to above tested sample only and shall not be reproduced in part without written approval of Shenzhen Anbotek Compliance Laboratory Limited. Date of Test : Sept. 26~ Nov. 11, 2014 Prepared by : (Engineer / Kebo Zhang) Reviewer : (Project Manager/Amy Ding) Approved & Authorized Signer : (Manager/Tom Chen) Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 4 of 31 Report No.: R011409364E 1. GENERAL INFORMATION 1.1. Description of Device (EUT) EUT : Bluetooth Speaker Model Number : A7910 Test Power Supply : DC 5V via adapter AC 120V, 60Hz/ DC 5V(With DC 3.7V Battery inside) Frequency : 2402-2480MHz No. of Channel : 79 Channel Space : 1MHz Antenna : Printed Antenna: 0 dBi Specification Applicant : Anker Technology Co., Limited Address : Room 1318-19, Hollywood Commercial Center, 610 Nathan Road, Mongkok, Kowloon, Hongkong Manufacturer : Anker Technology Co., Limited Address : Room 1318-19, Hollywood Commercial Center, 610 Nathan Road, Mongkok, Kowloon, Hongkong Factory : Anker Technology Co., Limited Address : Room 1318-19, Hollywood Commercial Center, 610 Nathan Road, Mongkok, Kowloon, Hongkong Date of receiver : Sept. 26, 2014 Date of Test : Sept. 26~ Nov. 11, 2014 Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 5 of 31 Report No.: R011409364E 1.2. Auxiliary Equipment Used during Test Adapter : Power Supply Model:MX12L3-0502000V Input: AC 100-240V, 50-60Hz, 0.35A Output: DC 5V, 2A CE , FCC 1.3. Description of Test Facility The test facility is recognized, certified, or accredited by the following organizations: CNAS - LAB Code: L3503 Shenzhen Anbotek Compliance Laboratory Limited., Laboratory has been assessed and in compliance with CNAS/CL01: 2006 accreditation criteria for testing laboratories (identical to ISO/IEC 17025:2005 General Requirements) for the Competence of Testing Laboratories. FCC-Registration No.: 752021 Shenzhen Anbotek Compliance Laboratory Limited, EMC Laboratory has been registed and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration 752021, July 10, 2013. IC-Registration No.: 8058A-1 Shenzhen Anbotek Compliance Laboratory Limited., EMC Laboratory has been registered and fully described in a report filed with the (IC) Industry Canada. The acceptance letter from the IC is maintained in our files. Registration 8058A-1, February 22, 2013. Test Location All Emissions tests were performed at Shenzhen Anbotek Compliance Laboratory Limited. at 1/F., Building 1, SEC Industrial Park, No.0409 Qianhai Road, Nanshan District, Shenzhen, Guangdong, China 1.4. Measurement Uncertainty Radiation Uncertainty : Ur = 4.3dB Conduction Uncertainty : Uc = 3.4dB Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 6 of 31 Report No.: R011409364E 2. Test Procedure GENERAL: This report shall NOT be reproduced except in full without the written approval of Shenzhen Anbotek Compliance Laboratory Limited. The EUT was transmitting a test signal during the testing. RADIATION INTERFERENCE: The test procedure used was ANSI STANDARD C63.4-2009 using a spectrum analyzer with a pre-selector. The analyzer was calibrated in dB above a microvolt at the output of the antenna. The resolution bandwidth was 100KHz and the video bandwidth was 300KHz up to 1.0GHz and 1.0MHz with a video BW of 3.0MHz above 1.0GHz. The ambient temperature of the EUT was 74.3oF with a humidity of 69%. FORMULA OF CONVERSION FACTORS: The Field Strength at 3m was established by adding the meter reading of the spectrum analyzer (which is set to read in units of dBuV) to the antenna correction factor supplied by the antenna manufacturer. The antenna correction factors are stated in terms of dB. The gain of the Preselector was accounted for in the Spectrum Analyzer Meter Reading. Example: Freq (MHz) METER READING + ACF = FS 20 dBuV + 10.36 dB = 30.36 dBuV/m @ 3m ANSI STANDARD C63.4-2009 10.1.7 MEASUREMENT PROCEDURES: The EUT was placed on a table 80 cm high and with dimensions of 1m by 1.5m. The EUT was placed in the center of the table (1.5m side). The table used for radiated measurements is capable of continuous rotation. When an emission was found, the table was rotated to produce the maximum signal strength. At this point, the antenna was raised and lowered from 1m to 4m. The antenna was placed in both the horizontal and vertical planes. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 7 of 31 Report No.: R011409364E 3. Conducted Limits Test Equipment Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. Two-Line Rohde & Schwarz ENV216 100055 Apr. 22, 2014 1 Year V-network 2. EMI Test Receiver Rohde & Schwarz ESCI 100627 Apr. 22, 2014 1 Year 3. Compliance RF Switching Unit RSU-M2 38303 Apr. 22, 2014 1 Year Direction 3.1. Block Diagram of Test Setup 3.1.1. Block diagram of connection between the EUT and simulators Test Receiver AC mains Adapter EUT L.I.S.N 3.2. Power Line Conducted Emission Measurement Limits (15.207) Frequency Limits dB(V) MHz Quasi-peak Level Average Level 0.15 ~ 0.50 66 ~ 56* 56 ~ 46* 0.50 ~ 5.00 56 46 5.00 ~ 30.00 60 50 Notes: 1. *Decreasing linearly with logarithm of frequency. 2. The lower limit shall apply at the transition frequencies. 3.3. Configuration of EUT on Measurement The following equipments are installed on Power Line Conducted Emission Measurement to meet the commission requirement and operating regulations in a manner which tends to maximize its emission characteristics in a normal application. 3.4. Operating Condition of EUT 3.4.1. Setup the EUT and simulator as shown as Section 3.1. 3.4.2. Turn on the power of all equipment. 3.4.3. Let the EUT work in test mode (Charging to adapter) and measure it. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 8 of 31 Report No.: R011409364E 3.5. Test Procedure The EUT system is connected to the power mains through a line impedance stabilization network (L.I.S.N.). This provides a 50ohm coupling impedance for the EUT system. Please refer the block diagram of the test setup and photographs. Both sides of AC line are checked to find out the maximum conducted emission. In order to find the maximum emission levels, the relative positions of equipment and all of the interface cables shall be changed according to FCC ANSI C63.4-2003 on Conducted Emission Measurement. The bandwidth of test receiver (ESCI) set at 9KHz. The frequency range from 150KHz to 30MHz is checked. The test results are reported on Section 3.6. 3.6. Power Line Conducted Emission Measurement Results PASS. The frequency range from 150KHz to 30 MHz is investigated. Please refer the following pages. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 9 of 31 Report No.: R011409364E CONDUCTED EMISSION TEST DATA Test Site: 1# Shielded Room Operating Condition: Charging to adapter Test Specification: DC 5V via adapter AC 120V, 60Hz Comment: Live Line Tem:25℃ Hum:50% Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 10 of 31 Report No.: R011409364E CONDUCTED EMISSION TEST DATA Test Site: 1# Shielded Room Operating Condition: Charging to adapter Test Specification: DC 5V via adapter AC 120V, 60Hz Comment: Neutral Line Tem:25℃ Hum:50% Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 11 of 31 Report No.: R011409364E 4. Radiation Interference 4.1. Requirements (15.249, 15.209): 4.1.1. Test Limits (< 30 MHZ) Frequency Field Strength Measurement Distance (MHz) (microvolts/meter) (meter) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 4.1.2. Test Limits (≥ 30 MHZ) FIELD STRENGTH FIELD STRENGTH S15.209 of Fundamental: of Harmonics 30 - 88 MHz 40 dBuV/m @3M 902-928 MHZ 88 - 216 MHz 43.5 2.4-2.4835 GHz 216 - 960 MHz 46 94 dBμV/m @3m 54 dBμV/m @3m ABOVE 960 MHz 54dBuV/m For range 9KHz~30MHz, The measured value is really too low to be recorded. Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in 15.209, whichever is the lesser attenuation. 4.2. Test Procedure The EUT is placed on a turn table which is 0.8 meter high above the ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT is set 3 meters away from the receiving antenna which is mounted on a antenna tower. The antenna can be moved up and down from 1 to 4 meters to find out the maximum emission level. Both horizontal and vertical polarization of the antenna are set on test. All readings from 30MHz to 1GHz are quasi-peak values with a resolution bandwidth of 120kHz. All reading are above 1GHz, peak & average values with a resolution bandwidth of 1MHz. The EUT is tested in 9*6*6 Chamber. The test results are listed in Section 4.3. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 12 of 31 Report No.: R011409364E Test Equipment Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. Spectrum Analysis Agilent E4407B US39390582 Aug. 08, 2014 1 Year Instruments EMC01183 2. Preamplifier 980100 Aug. 08, 2014 1 Year corporation 0 3. EMI Test Receiver Rohde & Schwarz ESPI 101604 Apr. 22, 2014 1 Year Double Ridged Instruments 4. GTH-0118 351600 Apr. 04, 2014 1 Year Horn Antenna corporation Bilog Broadband VULB 5. Schwarzbeck VULB9163 Apr. 24, 2014 1 Year Antenna 9163-289 6. Pre-amplifier SONOMA 310N 186860 Aug. 08, 2014 1 Year EMI Test 7. Software SHURPLE N/A N/A N/A N/A EZ-EMC 4.3. Test Configuration: 4.3.1. 9k to 30MHz emissions: 4.3.2. 30M to 1G emissions: Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 13 of 31 Report No.: R011409364E 4.3.3. 1G to 40G emissions: 4.4. Test Results PASS. The EUT was tested on (Charging to adapter, BT Mode) modes, only the worst data of (BT Mode(BDR)) are attached in the following pages. Data: Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 14 of 31 Report No.: R011409364E Below 1GHz: Job No.: 011409364E Polarziation: Horizontal Standard: (RE)FCC PART15 C _3m Power Source: DC 3.7V Test item: Radiation Test Temp.(C)/Hum.(%RH): 24.3( C)/55%RH Mode: BT Mode(BDR) Distance: 3m Note: 30-1000MHz Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 15 of 31 Report No.: R011409364E Job No.: 011409364E Polarziation: Vertical Standard: (RE)FCC PART15 C _3m Power Source: DC 3.7V Test item: Radiation Test Temp.(C)/Hum.(%RH): 24.3( C)/55%RH Mode: BT Mode(BDR) Distance: 3m Note: 30-1000MHz Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 16 of 31 Report No.: R011409364E Above 1 GHz: The worst mode: BDR Horizontal CH Low (2402MHz) Cable Ant Preamp Read Over Frequency Level Limit Remark Loss Factor Factor Level Limit MHz dB dB/m dB dBμV dBμV/m dBμV/m dB 2402.000 2.17 31.21 35.30 89.41 87.49 114.0 -26.51 Peak 2402.000 2.17 31.21 35.30 80.34 78.42 94.0 -15.58 AV 4804.000 2.56 34.01 34.71 49.65 51.51 74.0 -22.49 Peak 4804.000 2.56 34.01 34.71 34.02 35.88 54.0 -18.12 AV 7206.000 2.98 36.16 35.15 48.41 52.40 74.0 -21.60 Peak 7206.000 2.98 36.16 35.15 34.09 38.08 54.0 -15.92 AV 9608.000 --- --- --- --- --- --- --- --- 9608.000 --- --- --- --- --- --- --- --- 12010.000 --- --- --- --- --- --- --- --- 12010.000 --- --- --- --- --- --- --- --- --- . Vertical CH Low (2402MHz) Cable Ant Preamp Read Over Frequency Level Limit Remark Loss Factor Factor Level Limit MHz dB dB/m dB dBμV dBμV/m dBμV/m dB 2402.000 2.17 31.21 35.30 91.59 89.67 114.0 -24.33 Peak 2402.000 2.17 31.21 35.30 83.67 81.75 94.0 -12.25 AV 4804.000 2.56 34.01 34.71 48.47 50.33 74.0 -23.67 Peak 4804.000 2.56 34.01 34.71 34.52 36.38 54.0 -17.62 AV 7206.000 2.98 36.16 35.15 43.61 47.60 74.0 -26.40 Peak 7206.000 2.98 36.16 35.15 36.43 40.42 54.0 -13.58 AV 9608.000 --- --- --- --- --- --- --- --- 9608.000 --- --- --- --- --- --- --- --- 12010.000 --- --- --- --- --- --- --- --- 12010.000 --- --- --- --- --- --- --- --- --- NOTE: “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. The results of different modulations are the same. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 17 of 31 Report No.: R011409364E Horizontal CH Middle (2441MHz) Cable Ant Preamp Read Over Frequency Level Limit Remark Loss Factor Factor Level Limit MHz dB dB/m dB dBμV dBμV/m dBμV/m dB 2441.000 2.19 31.22 34.60 91.78 90.59 114.0 -23.41 Peak 2441.000 2.19 31.22 34.60 81.04 79.85 94.0 -14.15 AV 4882.000 2.57 35.00 34.58 45.01 48.00 74.0 -26.00 Peak 4882.000 2.57 35.00 34.58 38.46 41.45 54.0 -12.55 AV 7323.000 3.00 36.17 35.14 46.28 50.31 74.0 -23.69 Peak 7323.000 3.00 36.17 35.14 35.30 39.33 54.0 -14.67 AV 9764.000 --- --- --- --- --- --- --- --- 9764.000 --- --- --- --- --- --- --- --- 12205.000 --- --- --- --- --- --- --- --- 12205.000 --- --- --- --- --- --- --- --- --- Vertical CH Middle (2441MHz) Cable Ant Preamp Read Over Frequency Level Limit Remark Loss Factor Factor Level Limit MHz dB dB/m dB dBμV dBμV/m dBμV/m dB 2441.000 2.19 31.22 34.60 93.21 92.02 114.0 -21.98 Peak 2441.000 2.19 31.22 34.60 80.14 78.95 94.0 -15.05 AV 4882.000 2.57 35.00 34.58 46.32 49.31 74.0 -24.69 Peak 4882.000 2.57 35.00 34.58 37.24 40.23 54.0 -13.77 AV 7323.000 3.00 36.17 35.14 47.18 51.21 74.0 -22.79 Peak 7323.000 3.00 36.17 35.14 34.68 38.71 54.0 -15.29 AV 9764.000 --- --- --- --- --- --- --- --- 9764.000 --- --- --- --- --- --- --- --- 12205.000 --- --- --- --- --- --- --- --- 12205.000 --- --- --- --- --- --- --- --- --- NOTE: “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. The results of different modulations are the same. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 18 of 31 Report No.: R011409364E Horizontal CH High (2480MHz) Cable Ant Preamp Read Over Frequency Level Limit Remark Loss Factor Factor Level Limit MHz dB dB/m dB dBμV dBμV/m dBμV/m dB 2480.000 2.20 31.65 36.00 94.35 92.20 114.0 -21.80 Peak 2480.000 2.20 31.65 36.00 82.46 80.31 94.0 -13.69 AV 4960.000 2.58 35.06 34.79 50.13 52.98 74.0 -21.02 Peak 4960.000 2.58 35.06 34.79 36.41 39.26 54.0 -14.74 AV 7440.000 3.02 36.19 34.90 47.03 51.34 74.0 -22.66 Peak 7440.000 3.02 36.20 35.20 37.09 41.11 54.0 -12.89 AV 9920.000 --- --- --- --- --- --- --- --- 9920.000 --- --- --- --- --- --- --- --- 12400.000 --- --- --- --- --- --- --- --- 12400.000 --- --- --- --- --- --- --- --- --- Vertical CH High (2480MHz) Cable Ant Preamp Read Over Frequency Level Limit Remark Loss Factor Factor Level Limit MHz dB dB/m dB dBμV dBμV/m dBμV/m dB 2480.000 2.20 31.65 36.00 93.67 91.52 114.0 -22.48 Peak 2480.000 2.20 31.65 36.00 83.17 81.02 94.0 -12.98 AV 4960.000 2.58 35.06 34.79 47.46 50.31 74.0 -23.69 Peak 4960.000 2.58 35.06 34.79 34.55 37.40 54.0 -16.60 AV 7440.000 3.02 36.19 34.90 45.46 49.77 74.0 -24.23 Peak 7440.000 3.02 36.20 35.20 37.04 41.06 54.0 -12.94 AV 9920.000 --- --- --- --- --- --- --- --- 9920.000 --- --- --- --- --- --- --- --- 12400.000 --- --- --- --- --- --- --- --- 12400.000 --- --- --- --- --- --- --- --- --- NOTE: “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. The results of different modulations are the same. Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 19 of 31 Report No.: R011409364E 5. Occupied Bandwidth 5.1. Requirements (15.249): The field strength of any emissions appearing outside the band edges and up to 10 kHz above and below the band edges shall be attenuated at least 50 dB below the level of the carrier or to the general limits of 15.249. 5.2. Test Procedure The EUT is placed on a turn table which is 0.8 meter high above the ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT is set 3 meters away from the receiving antenna which is mounted on a antenna tower. The antenna can be moved up and down from 1 to 4 meters to find out the maximum emission level. Both horizontal and vertical polarization of the antenna are set on test. Test Equipment Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. Spectrum Analysis Agilent E4407B US39390582 Aug. 08, 2014 1 Year Instruments EMC01183 2. Preamplifier 980100 Aug. 08, 2014 1 Year corporation 0 3. EMI Test Receiver Rohde & Schwarz ESPI 101604 Apr. 22, 2014 1 Year Double Ridged Instruments 4. GTH-0118 351600 Apr. 04, 2014 1 Year Horn Antenna corporation Bilog Broadband VULB 5. Schwarzbeck VULB9163 Apr. 24, 2014 1 Year Antenna 9163-289 6. Pre-amplifier SONOMA 310N 186860 Aug. 08, 2014 1 Year EMI Test 7. Software SHURPLE N/A N/A N/A N/A EZ-EMC 5.3. Test Configuration: Same as the test configuration in 4.3. 5.4. Test Results Pass. Please refer the following plot. (Note: Marker 3 means the highest value in 2.39GHz~2.4GHz or 2.4835~2.5GHz) Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 20 of 31 Report No.: R011409364E The worst mode: BDR Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 21 of 31 Report No.: R011409364E The worst mode: BDR 20dB Down: Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 22 of 31 Report No.: R011409364E Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 23 of 31 Report No.: R011409364E 6. PHOTOGRAPH 6.1. Photo of Conducted Emission Test 6.2. Photo of Radiation Emission Test Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 24 of 31 Report No.: R011409364E Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 25 of 31 Report No.: R011409364E APPENDIX I (EXTERNAL PHOTOS) Figure 1 The EUT-Top View Figure 2 The EUT-Bottom View Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 26 of 31 Report No.: R011409364E Figure 3 The EUT-Front View Figure 4 The EUT-Back View Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 27 of 31 Report No.: R011409364E Figure 5 The EUT-Left View Figure 6 The EUT-Right View Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 28 of 31 Report No.: R011409364E APPENDIX II(INTERNAL PHOTOS) Figure 7 The EUT-Inside View Figure 8 The EUT-Inside View Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 29 of 31 Report No.: R011409364E Figure 9 The EUT-Inside View Figure 10 PCB of the EUT-Front View Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 30 of 31 Report No.: R011409364E Figure 11 PCB of the EUT-Back View Figure 12 PCB of the EUT-Front View Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AB7K-A7910 Page 31 of 31 Report No.: R011409364E Figure 13 PCB of the EUT-Back View Shenzhen Anbotek Compliance Laboratory Limited Tel:(86)755-26066544 Fax:(86)755-26014772 www.anbotek.com


Document Created: 2019-09-16 22:55:33
Document Modified: 2019-09-16 22:55:33
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC