Users Manual

FCC ID: 2AB2QNS01RA13FR125

Users Manual

Download: PDF
FCCID_4244971

Installation Instruction Packaging contents: LED Retrofit kit: 1pcs Installation Instruction: 1pcs Friction bracket: 2pcs E26 lamp base: 1pcs Remot:1pcs WARNING WARNING – Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician. WARNING – Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire. Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation. WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. WARNING –This device is not intended for use with emergency exits. WARING- DO NOT USE WITH STANDARD DIMMERS WARING- -SUITABLE FOR WET LOCATIONS Federal Communications Commission (FCC) Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. Only use the control provided with the instruction to control this lamp. This lamp will not operate properly when connected to a standard dimmer or dimming control The product is intended to retrofit Type IC or Type non-IC recessed mount Listed luminaires that use one lamp with or without a diffuser. The minimum lamp compartment dimensions are tabulated below: Lamp compartment of Luminaire, overall Diameter 189.5 dimensions, mm Height 70 Electrical parameters: Model NO. Input voltage(V) Frequency(Hz) Input Input wattage(W) Current(mA) NS01RA13FR1‐25zx 120 60 13 * x replaced by one digital numbers range 1 to 9 to denote different package style; z replaced by one digital numbers 8/9 to denote different CRI

Product siize: Unit: mm Installatioon steps: STEP1: Disconnect power beforre servicing. Remove the e existing bulb or remove the existing trim if neces ssary. *Tips: For tthe shallow housing a) Removve the adjustable socket bracket to asssure enough h space for the fixture (as sshown in How w to adjust shalloww housing soccket bracket)). b) Changee the torsion springs s into the t friction brrackets (as sh hown in How to change thhe torsion springs into friction n brackets) beefore installin ng the LED Reetrofit kit into o the shallow housing. STEP2: As shown in n Figure 1 Twist the lamp base into e lamp base to LED Retrofit kit by connnector. o the socket. Connect the ng the torsio *Tips: Chan on springs into friction n brackets iff necessary before conn nect the lam mp base and d LED Retroffit (as shown in How to ch hange the torrsion springs into friction brackets). Figure 1

STEP3: Arrange the e ends of torssion spring in nside the lam yonet or put the friction bbrackets into the housing mp holder bay (as shown in Figure 2). with torssion spring with friction bracketss Figure 2 STEP5: As shown in n Figure 3. Push the LEED Retrofit kitt into the hou using until itss outer edge is flush against the ceilinng surface. Figure 3 STEP6: Compete th he installation n and turn on the power ssupply. STEP7： Use the rem mote to conne nlight (as show ect the down wn in User Guide‐4 key re emote controoller‐Operation).

*How to adjust shallow hou using sockket bracke et Step1: Remove the e rotary knob b by rotating and then takke out the ad djustable socket bracket ((as shown in Figure 5). Figure 5 Step2: Remove the e the adjusta able socket bracket b by pre essing the so ocket clips (a as shown in Figure 6). Figure 6 Step3: Put the sockket back into the t housing (as n Figure 7). ( shown in Figure 7 *How to change th he torsion n springs in nto frictio on bracketts Loosen th he screws an nd remove th he torsion sp rings (as sho own in Figure e 8). Then fix tthe friction brrackets with the screws ((as shown in Figure 9). Figure 8 Figgure 9


Document Created: 2019-04-18 14:14:14
Document Modified: 2019-04-18 14:14:14
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC