14_ZAP 1L-Tx TestRpt DSC r4

FCC ID: 2AB22ZAP-5LX-S

Test Report

Download: PDF
FCCID_4389176

Test Report FCC ID: 2AB22ZAP-5LX-S Date of issue: Aug. 07, 2019 Report Number: MTi19071009-1E1 Sample Description: ZAP remote Model(s): ZAP 1L-Tx Applicant: Etekcity Corporation Address: 1202 N Miller St. Suite A, Anaheim, CA 92806, USA Date of Test: July 11, 2019 to Aug. 07, 2019 Shenzhen Microtest Co., Ltd. http://www.mtitest.com This test report is valid for the tested samples only. It cannot be reproduced except in full without prior written consent of Shenzhen Microtest Co., Ltd. Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 2 of 21 - Report No.: MTi19071009-1E1 Table of Contents 1 GENERAL DESCRIPTION ..................................................................................................................................... 4 1.1 DESCRIPTIONS OF EUT ............................................................................................................................................... 4 1.2 OPERATION CHANNEL LIST ........................................................................................................................................... 4 1.3 FREQUENCY CHANNEL UNDER TEST .............................................................................................................................. 4 1.4 ANCILLARY EQUIPMENT LIST ......................................................................................................................................... 4 1.5 DESCRIPTION OF SUPPORT UNITS ................................................................................................................................. 4 2 SUMMARY OF TEST RESULTS ............................................................................................................................. 5 3 TEST FACILITIES AND ACCREDITATIONS .............................................................................................................. 6 3.1 TEST LABORATORY...................................................................................................................................................... 6 3.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 6 3.3 MEASUREMENT UNCERTAINTY ................................................................................................................................. 6 3.4 TEST SOFTWARE ........................................................................................................................................................ 6 4 EQUIPMENT LIST ............................................................................................................................................... 7 5 TEST RESULT ...................................................................................................................................................... 8 5.1 ANTENNA REQUIREMENT ............................................................................................................................................ 8 5.1.1 Requirement defined in FCC 15.203 ............................................................................................................ 8 5.1.2 EUT antenna description ............................................................................................................................. 8 5.2 AC POWER LINE CONDUCTED EMISSION .................................................................................................................... 9 5.2.1 Limit ............................................................................................................................................................ 9 5.2.2 Test method ................................................................................................................................................ 9 5.2.3 Test Result ................................................................................................................................................... 9 5.3 FIELD STRENGTH OF FUNDAMENTAL AND HARMONIC EMISSIONS ................................................................................. 10 5.3.1 Limits ......................................................................................................................................................... 10 5.3.2 Test Method .............................................................................................................................................. 11 5.3.3 Test Result ................................................................................................................................................. 12 5.4 OCCUPIED BANDWIDTH....................................................................................................................................... 13 5.4.1 Test method .............................................................................................................................................. 13 5.4.2 Test result.................................................................................................................................................. 14 5.5 RADIATED EMISSION AND BAND EDGE SPURIOUS EMISSION ....................................................................................... 15 5.5.1 Limit .......................................................................................................................................................... 15 5.5.2 Test method .............................................................................................................................................. 15 5.5.3 Test Result ................................................................................................................................................. 15 5.6 TRANSMITTER TIMEOUT ...................................................................................................................................... 19 5.6.1 Limit .......................................................................................................................................................... 19 5.6.2 Test method .............................................................................................................................................. 19 5.6.3 Test Result ................................................................................................................................................. 19 PHOTOGRAPHS OF THE TEST SETUP ...........................................................................................................................20 PHOTOGRAPHS OF THE EUT .......................................................................................................................................21 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 3 of 21 - Report No.: MTi19071009-1E1 Test Result Certification Applicant’s name: Etekcity Corporation Address: 1202 N Miller St. Suite A, Anaheim, CA 92806, USA Manufacture's Name: Dongguan Raiwee Electronic Technology Co., Ltd Building 11, Antouling, Industry Avenue, Qinghu Village, Qishi Address: Town, Dongguan, Guangdong 523000, China Product name: ZAP remote Trademark: ETEKCITY Model name: ZAP 1L-Tx Standards: FCC Part 15.231 ANSI C63.10-2013 Test Procedure: DA 00-705 This device described above has been tested by Shenzhen Microtest Co., Ltd. and the test results show that the equipment under test (EUT) compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Tested by: Jone Lee Aug. 07, 2019 Reviewed by: Blue Zheng Aug. 07, 2019 Approved by: Smith Chen Aug. 07, 2019 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 4 of 21 - Report No.: MTi19071009-1E1 1 General description 1.1 Descriptions of EUT Product name: ZAP remote Model name: ZAP 1L-Tx Series model: N/A Difference of series model: N/A Tx/Rx frequency range: Tx:433.92MHz Modulation type: ASK Power source: DC 12V from battery Adapter information: N/A Antenna designation: PCB Antenna(Antenna Gain:1dBi ) Hardware version: V1.0.1 Software version: V1.0 1.2 Operation channel list Channel Frequency 1 433.92MHz 1.3 Frequency Channel Under Test Channel Frequency 1 433.92MHz 1.4 Ancillary equipment list Equipment Model S/N Manufacturer / / / / 1.5 Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Brand Model/Type No. Series No. Note / / / / / / / / / / Note: (1)The support equipment was authorized by Declaration of Confirmation. (2)For detachable type I/O cable should be specified the length in cm in『Length』column. Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 5 of 21 - Report No.: MTi19071009-1E1 2 Summary of Test Results Test procedures according to the technical standards: Item FCC Part No. Description of Test Result Remark 1 15.203 Antenna requirement Pass AC power line conducted 2 15.207 N/A emission Field strength of fundamental 3 15.231(b) Pass and harmonic emissions 15.205 and Radiated emission and 4 Pass 15.209 bandedge 5 15.215 Occupied Bandwidth Pass 6 15.231(a)(2) Release time Pass The meaning of symbols: “ZAP 1L-Tx ” – Not Applicable Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 6 of 21 - Report No.: MTi19071009-1E1 3 Test Facilities and Accreditations 3.1 Test laboratory Test Laboratory Shenzhen Microtest Co., Ltd No.102A & 302A, East Block, Hengfang Industrial Park, Location Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China FCC Registration 448573 No.: 3.2 Environmental conditions Temperature: 15ºC~35ºC Humidity 20%~75% Atmospheric 98kPa~101kPa pressure 3.3 Measurement uncertainty The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 % RF frequency 1 x 10-7 RF power, conducted ±1.38dB Conducted emission(150kHz~30MHz) ±0.21dB Radiated emission(30MHz~1GHz) ±4.68dB Radiated emission (above 1GHz) ±4.89dB Temperature ±0.5°C Humidity ±2 % 3.4 Test software Software Manufacturer Model Version Name Shenzhen JS RF Test System JS1120-3 2.5.77.0418 tonscend co., ltd Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 7 of 21 - Report No.: MTi19071009-1E1 4 Equipment list Equipment Manufactu Serial Calibration Equipment Name Model Due date No. rer No. date Rohde&sch MTI-E004 EMI Test Receiver ESPI7 100314 2018/10/09 2019/10/08 warz TRILOG Broadband MTI-E006 schwarabeck VULB 9163 9163-872 2018/10/15 2020/10/14 Antenna Hewlett-Pac 3113A0615 MTI-E014 amplifier 8447D 2018/10/09 2019/10/08 kard 0 Single path vehicle Schwarzbec MTI-E036 NNBM 8124 01175 2018/10/09 2019/10/08 AMN(LISN) k Low noise active Schwarzbec MTI-E038 vertical monopole VAMP 9243 #565 2018/10/16 2019/10/15 k antenna Schwarzbec MTI-E039 Biconical antenna BBA 9106 #164 2018/10/15 2019/10/14 k MXG Vector Signal MY490604 MTI-E041 Agilent N5182A 2019/04/16 2020/04/15 Generator 55 ESG Series Analog GB400512 MTI-E042 Agilent E4421B 2019/05/21 2020/05/20 signal generator 40 Thermometer clock MTI-E044 - HTC-1 / 2019/04/17 2020/04/16 humidity monitor Schwarzbec MTI-E062 Log Periodic Antenna VUSLP 9111B #312 2018/04/11 2020/04/10 k Log Periodic Dipole ETS-LINDG MTI-E063 3148B 00224524 2018/04/11 2020/04/10 Array Antenna REN MTI-E065 Amplifier EMtrace RP06A 00117 2019/04/29 2020/04/28 Comprehensive test Rohde&sch MTI-E066 CMW500 149155 2019/04/16 2020/04/15 instrument warz MY513502 MTI-E071 PXA Signal Analyzer Agilent N9030A 2018/10/25 2019/10/24 96 Rohde&sch MTI-E076 EMI Test Receiver ESIB26 100273 2019/04/16 2020/04/15 warz 3610A0195 MTI-E078 Synthesized Sweeper Agilent 83752A 2019/04/16 2020/04/15 7 MY400276 MTI-E079 DC Power Supply Agilent E3632A 2019/04/16 2020/04/15 95 Artificial mains ES391180 MTI-E093 3ctest LISN J50 2019/04/16 2020/04/15 network 5 Space-Dtroni EWLNA0118G- MTI-E096 Power amplifier 1852001 2019/04/29 2020/04/28 ccs P40 SOLAR MTI-E097 Current Probe ELECTRONI 9207-1 220095-1 2019/04/17 2020/04/16 CS CO. SOLAR MTI-E098 Loop Sensor ELECTRONI 7334-1 220095-2 2019/04/21 2020/04/20 CS CO. Note: the calibration interval of the above test instruments is 12 months and the calibrations are traceable to international system unit (SI). Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 8 of 21 - Report No.: MTi19071009-1E1 5 Test Result 5.1 Antenna requirement 5.1.1 Requirement defined in FCC 15.203 An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier current devices or to devices operated under the provisions of §15.211, §15.213, §15.217, §15.219, or §15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional radiators which, in accordance with §15.31(d), must be measured at the installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed so that the limits in this part are not exceeded. 5.1.2 EUT antenna description The radio antenna of EUT is a PCB antenna, the maximum gain is 1dBi. So the antenna meets the requirement of this part. PCB Antenna Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 9 of 21 - Report No.: MTi19071009-1E1 5.2 AC power line conducted emission 5.2.1 Limit Frequency Limit (MHz) Quasi-peak Average 0.15-0.5 66 to 56 56 to 46 0.5-5 56 46 5-30 60 50 Note: Decreases with the logarithm of the frequency from 0.15MHz to 0.5MHz. 5.2.2 Test method 1. The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipment powered from additional LISN(s). The LISN provide 50 Ohm/50uH of coupling impedance for the measuring instrument. 2. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. 3. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. 4. LISN is at least 80 cm from nearest part of EUT chassis. 5. The resolution bandwidth of EMI test receiver is set at 9kHz. 5.2.3 Test Result Note: The device is a DC power supply and does not apply to conducted emissions. Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 10 of 21 - Report No.: MTi19071009-1E1 5.3 Field strength of fundamental and harmonic emissions 5.3.1 Limits Intentional radiators may operate at a periodic rate exceeding that specified in paragraph (a) of this section and may be employed for any type of operation, including operation prohibited in paragraph (a) of this section, provided the intentional radiator complies with the provisions of paragraphs (b) through (d) of this section, except the field strength table in paragraph (b) of this section is replaced by the following: Fundamental frequency Field strength of fundamental Field strength of spurious (MHz) (microvolts/meter) emissions (microvolts/meter) 40.66-40.70 2.250 225 70-130 1.250 125 1 1 130-174 1250 to 3750 125 to 375 174-260 3.750 375 1 1 260-470 3750 to 12500 375 to 1250 Above 470 12500 1250 1 Linear interpolations. For example for 433.925MHz uV/m 12500 3750 260 EUT frequency(X) 470 Frequency (MHz) The Field Strength of Fundamental Emissions (Operating Frequency) is: 3750 uV/m = 20*log (3750) dBuV/m = 71.48 dBuV/m 12500 uV/m = 20*log (12500) dBuV/m = 81.94 dBuV/m For example the Fundamental emission is 433.925MHz, the limit is X. (433.92-260)/(470-260)=(X-3750)/(12500-3750) 173.925/210 =(X-3750)/8750 X = 10996.875uV/m AV Limit = 20*log (10996.875) dBuV/m = 80.83 dBuV/m PK Limit = 100.83 dBuV/m Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 11 of 21 - Report No.: MTi19071009-1E1 5.3.2 Test Method 1. The EUT is placed on a turntable, which is 0.8m above ground plane for test frequency range blew 1GHz, and 1.5m above ground plane for test frequency range above 1GHz. 2. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 3. Use the following spectrum analyzer settings: Span = wide enough to fully capture the emission being measured RBW = 1 MHz for f ≥ 1GHz RBW = 100 kHz for f < 1 GHz VBW ≥ RBW Sweep = Auto Detector function = Peak Trace = max hold 4. Follow the guidelines in ANSI C63.4-2014 with respect to maximizing the emission by rotating the EUT, adjusting the measurement antenna height and polarization, etc. The peak reading of the emission, after being corrected by the antenna factor, cable loss, pre-amp gain, etc., is the peak field strength, submit this data. Each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 5. The peak level, once corrected, must comply with the limit specified in Section 15.209. Set the spectrum to RBW = 1MHz VBW = 10Hz Detector = PK for AV value, while maintaining all of the other instrument settings Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 12 of 21 - Report No.: MTi19071009-1E1 5.3.3 Test Result Field Strength of Fundamental Emissions and Field strength of spurious emissions Value Field Operating Frequency Limit @3m Margin Strength Detector Antenna (MHz) (dBuV/m) (dB) (dBuV/m) 78.26 Peak 100.83 22.57 Vertical 67.8 Average 80.83 13.03 Vertical 433.920 79.52 Peak 100.83 21.31 Horizontal 69.06 Average 80.83 11.77 Horizontal 54.34 Peak 80.83 26.49 Vertical 43.88 Average 60.83 16.95 Vertical 869.1301 53.45 Peak 80.83 27.38 Horizontal 42.99 Average 60.83 17.84 Horizontal Note: If the PK measured values lower than average mode limit, the EUT shall be deemed to meet average limits and then no additional average mode measurement performed. Note: 1. EUT Pre-scan X/Y/Z orientation, only worst case is presented in the report(Y orientation). 2. *Calculate Average value based on Duty Cycle correction factor: Duty Cycle=Ton/(Ton+Toff)= 225ms/750ms = 0.3=30% Duty Cycle factor= 20lg (Duty Cycle) =20lg (0.3) = -10.46dB Average=Peak+ Duty Cycle factor 3. Margin: Limit- Field Strength 433.92MHz Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 13 of 21 - Report No.: MTi19071009-1E1 5.4 Occupied Bandwidth 5.4.1 Test method Use the following spectrum analyzer settings: Span = approximately 2 to 3 times the 20 dB bandwidth, centered on a hopping channel RBW ≥1% of the 20 dB bandwidth VBW ≥RBW Sweep = auto Detector function = peak Trace = max hold The EUT should be transmitting at its maximum data rate. Allow the trace to stabilize. Use the marker-to-peak function to set the marker to the peak of the emission. Use the marker-delta function to measure 20 dB down one side of the emission. Reset the marker-delta function, and move the marker to the other side of the emission, until it is (as close as possible to) even with the reference marker level. The marker-delta reading at this point is the 20 dB bandwidth and 99% occupied bandwidth of the emission. The bandwidth of the emission shall be no wider than 0.25% of the center frequency for devices operating above 70 MHz and below 900 MHz. For devices operating above 900 MHz, the emission shall be no wider than 0.5% of the center frequency. Bandwidth is determined at the points 20 dB down from the modulated carrier Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 14 of 21 - Report No.: MTi19071009-1E1 5.4.2 Test result Test modulation: ASK 99% occupied Limits(MHz) 20dB emission Frequency (MHz) bandwidth bandwidth (MHz) (MHz) 433.92 0.4192 0.73856 1.08 Test plots as below 433.92MHz Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 15 of 21 - Report No.: MTi19071009-1E1 5.5 Radiated emission and Band edge spurious emission 5.5.1 Limit Emissions radiated outside of the specified frequency bands, except for harmonic emissions, (b)shall be attenuated by at least 50 dB below the level of the fundamental emissions or to the general field strength limits listed in RSS-Gen, whichever is less stringent. Field Field Frequency Measurement strength strength Detector (MHz) distance μV/m dBμV/m 30-88 100 40 QP 88-216 150 43.5 QP 216-960 200 46 QP 3m 960-1000 500 54 QP Above 1000 500 54 AV Above 1000 5000 74 PK 5.5.2 Test method 1. The EUT is placed on a turntable, which is 0.8m above ground plane for test frequency range blew 1GHz, and 1.5m above ground plane for test frequency range above 1GHz. 2. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 3. Use the following spectrum analyzer settings: Span = wide enough to fully capture the emission being measured RBW = 1 MHz for f ≥ 1GHz 100 kHz for f < 1 GHz, VBW ≥ RBW Sweep = auto Detector function = peak Trace = max hold 4. Follow the guidelines in ANSI C63.4-2014 with respect to maximizing the emission by rotating the EUT, adjusting the measurement antenna height and polarization, etc. The peak reading of the emission, after being corrected by the antenna factor, cable loss, pre-amp gain, etc., is the peak field strength, submit this data. Each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 5. The peak level, once corrected, must comply with the limit specified in Section 15.209. Set the RBW = 1MHz, VBW = 10Hz, Detector = PK for AV value, while maintaining all of the other instrument settings. 5.5.3 Test Result Remark: If the PK measured values lower than average mode limit, the EUT shall be deemed to meet average limits and then no additional average mode measurement performed. Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 16 of 21 - Report No.: MTi19071009-1E1 Radiated emission Between 30MHz – 1GHz EUT： ZAP remote Model Name ： ZAP 1L-Tx Relative 52% Phase: H Humidity: Pressure： 1010 hPa Test Voltage ： DC 12V from battery Test Mode ： TX Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 17 of 21 - Report No.: MTi19071009-1E1 EUT： ZAP remote Model Name ： ZAP 1L-Tx Relative 52% Phase: V Humidity: Pressure： 1010 hPa Test Voltage ： DC 12V from battery Test Mode ： TX Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 18 of 21 - Report No.: MTi19071009-1E1 1G-6GHz Meter Emission Frequency Reading Factor Level Limits Margin Polar No. (MHz) (dBuV) dB) (dBuV/m) (dBuV/m) (dB) (H/V) 1355.738 43.29 -9.96 33.33 74 -40.67 Horizontal 1 2 2070.131 44.93 -9.17 35.76 74 -38.24 Horizontal 3 3157.061 44.72 -9.25 35.47 74 -38.53 Horizontal 4 3852.211 42.99 -9.04 33.95 74 -40.05 Horizontal 5 4902.902 47.67 -9.96 37.71 74 -36.29 Horizontal 6 5613.507 43.62 -9.65 33.97 74 -40.03 Horizontal 1526.384 47.79 -9.77 38.02 74 -35.98 Vertical 1 2 2202.488 48.04 -9.93 38.11 74 -35.89 Vertical 3 3053.802 47.59 -9.10 38.49 74 -35.51 Vertical 4 3928.957 46.41 -9.90 36.51 74 -37.49 Vertical 5 5199.723 52.55 -9.11 43.44 74 -30.56 Vertical 6 5680.524 49.41 -9.87 39.54 74 -34.46 Vertical Note1 : Absolute Level = Reading Level+ Factor, Margin= Absolute Level- Limit, Factor = Antenna Factor + Cable Loss – Pre-amplifier. Note2 :The peak value is less than the AV value, AV value is not required Factor added by measurement software automatically. Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 19 of 21 - Report No.: MTi19071009-1E1 5.6 Transmitter timeout 5.6.1 Limit 15.231 (a)(1)A manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released. 5.6.2 Test method Setup the EUT as show in the block diagram above. Set Spectrum Analyzer Centre Frequency = Fundamental Frequency RBW=100 kHz, VBW= 300 kHz Span= 0 Hz Sweep Time= 10 Seconds. Setup the EUT as normal operation and press Transmitter button Release the button, use Delta Mark function to test the time. 5.6.3 Test Result Periodic operation time (s) Limit(s) Result 0.24 5 Pass Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 20 of 21 - Report No.: MTi19071009-1E1 Photographs of the Test Setup Radiated emission – below 1GHz Radiated emission – above 1GHz Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 21 of 21 - Report No.: MTi19071009-1E1 Photographs of the EUT See the APPENDIX 1: EUT PHOTO in the report No.: MTi19071009-1E1-1 ----End of Report---- Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China


Document Created: 2019-08-07 18:35:43
Document Modified: 2019-08-07 18:35:43
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC