Test report

FCC ID: 2AB22-ZAP1FXT

Test Report

Download: PDF
FCCID_3342373

Test Report FCC ID.: 2AB22-ZAP1FXT Date of issue: Mar. 15, 2017 Sample Description: Etekcity Outdoor Remote Control Outlet Transmitter Model(s): ZAP 1FXT Applicant: Etekcity Corporation Address: 1202 N Miller St. Suite A, Anaheim, CA 92806 Date of Test: Feb.28, 2017 to Mar. 15, 2017 ShenzhenMicrotest Co., Ltd. http://www.mtitest.com This test report is valid for the tested samples only. It cannot be reproduced except in full without prior written consent of Shenzhen Microtest Co., Ltd.. Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 2of 12- Report No.: MTi170228E061 TABALE OF CONTENTS TABALE OF CONTENTS ............................................................................................................. 2 1. General description ............................................................................................................... 5 1.1 Feature of equipment undertest (EUT)................................................................................ 5 1.2 operation channel list ........................................................................................................... 5 2. Test Configuration of EUT .................................................................................................... 6 2.1EUT operation mode .............................................................................................................. 6 2.2Testconditions........................................................................................................................ 6 2.3Testing site ............................................................................................................................. 6 2.4Ancillary equipment list ........................................................................................................ 6 2.5 Measurement uncertainty .................................................................................................... 6 3. List of test equipment ........................................................................................................... 7 4. Test Result ............................................................................................................................. 8 4.1Antenna requirement ............................................................................................................. 8 4.220dB emission bandwidth ..................................................................................................... 9 4.3Radiated emission ............................................................................................................... 10 4.4Time of occupancy (dwell time) .......................................................................................... 12 This test report is valid for the tested samples only. It cannot be reproduced except in full without prior written consent of Shenzhen Microtest Co., Ltd.. Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 3of 12- Report No.: MTi170228E061 TEST RESULT CERTIFICATION Applicant’s name: Etekcity Corporation Address: 1202 N Miller St. Suite A, Anaheim, CA 92806 Manufacture's Name: SHENZHEN SANCING TECHNOLOGY CO;LTD Room301, A Block Tus Technology Park Jianmin road Long Address: gang District Shenzhen China Product description Product name: Etekcity Outdoor Remote Control Outlet Transmitter Trademark: Etekcity Model name: ZAP 1FXT Serial Model: / Standards: FCC Part 15 C Test Procedure: ANSI C63.4-2014；ANSI C63.10-2013 This device described above has been tested by Shenzhen Microtest Co.,Ltd. and the test results show that the equipment under test (EUT) is in compliance with the FCCrequirements. And it is applicable only to the tested sample identified in the report. Tested by: Sangdi Huang Mar. 15, 2017 Reviewed by: Leon Chen Mar. 15, 2017 Approved by: Tom Xue Mar. 15, 2017 Tel:(86-755)88850135 Fax: (86-755) 88850136 http://www.mtitest.com E-mail:mti@51mti.com Address:1F& 3F, East Block, Hengfang Industrial Park, Xingye Road,Xixiang, Bao'an District, Shenzhen, Guangdong,P. R. China.

- Page 4of 12- Report No.: MTi170228E061 SUMMARY OF TEST RESULT Item FCC Part No. Description of Test Result 1 15.203 Antenna requirement Pass AC power line conducted 2 15.207 N/A emission 3 15.231(c) 20dB bandwidth Pass 4 15.231(b) Radiated emission Pass 5 15.231(a)(1) Release time Pass Tel:(86-755)88850135 Fax: (86-755) 88850136 http://www.mtitest.com E-mail:mti@51mti.com Address:1F& 3F, East Block, Hengfang Industrial Park, Xingye Road,Xixiang, Bao'an District, Shenzhen, Guangdong,P. R. China.

- Page 5of 12- Report No.: MTi170228E061 1. General description 1.1 Feature of equipment undertest (EUT) Product name: Etekcity Outdoor Remote Control Outlet Transmitter Model name: ZAP 1FXT Tx/Rx frequency range: Tx:433.92MHz Modulation type: ASK Power source: DC 12V/23A (ALKALINE BATTERY) Antenna designation: PCBA antenna Antenna Gain: 0dBi 1.2 operation channel list Channel Frequency 1 433.92MHz Tel:(86-755)88850135 Fax: (86-755) 88850136 http://www.mtitest.com E-mail:mti@51mti.com Address:1F& 3F, East Block, Hengfang Industrial Park, Xingye Road,Xixiang, Bao'an District, Shenzhen, Guangdong,P. R. China.

- Page 6of 12- Report No.: MTi170228E061 2. Test Configuration of EUT 2.1EUT operation mode During testing, the EUT is operated in TX mode. (new battery is used during all test) 2.2Testconditions During the measurement the environmental conditions were within the listed ranges: - Temperature: 20ºC~30ºC - Humidity: 30%~70% - Atmospheric pressure: 98kPa~101kPa 2.3Testing site Test Site Shenzhen Toby Technology Co., Ltd. 1 A/F., Bldg.6, Yusheng Industrial Zone The National Road Test Site Location No.107 Xixiang Section 467 FCC Registration 811562 No.: 2.4Ancillary equipment list Equipment Model S/N Manufacturer / / / / 2.5 Measurement uncertainty Measurement Uncertainty for a Level of Confidence of 95 %, U=2xUc(y) RF frequency 1 x 10-7 RF power, conducted ± 1 dB Conducted emission(150kHz~30MHz) ± 2.5 dB Radiated emission(30MHz~1GHz) ± 4.2 dB Radiated emission (above 1GHz) ± 4.3 dB Temperature ±1 degree Humidity ±5 % Tel:(86-755)88850135 Fax: (86-755) 88850136 http://www.mtitest.com E-mail:mti@51mti.com Address:1F& 3F, East Block, Hengfang Industrial Park, Xingye Road,Xixiang, Bao'an District, Shenzhen, Guangdong,P. R. China.

- Page 7of 12- Report No.: MTi170228E061 3. List of test equipment For RF conducted test: Equipment Manufacturer Model Serial No. Calibration Due Signal Analyzer Agilent N9010A MY48030494 2017/11/4 4 Ch. Simultaneous Sampling 14 Bits 2 Agilent U2531A TW54063513 2017/11/4 MS/s X-series USB Peak and Average Power Agilent U2021XA MY54080019 2017/11/4 Sensor vector Signal Agilent E4438C US44271917 2017/11/4 Generator vector Signal Agilent E4438C MY49070163 2017/11/4 Generator Dc Power Supply GW GPR-6030D / 2017/11/4 Temperature & GIANT FORCE GTH-056P GF-94454-1 2017/11/4 Humitidy Chamber For Radiated emission: Equipment Manufacturer Model Serial No. Calibration Due Broadband TRILOG Schwarabeck VULB9163 9163-872 2017/11/14 Antenna Horn Antenna Schwarzbeck BBHA 9120 D 9120D-1145 2017/11/14 Amplifier HP 8447D 3113A06150 2017/11/4 Amplifier Agilent 8449B 3008A02400 2017/7/4 Test Receiver Schwarabeck ESPI7 100314 2017/11/4 Spectrum analyzer Agilent E4407B MY41441082 2017/11/4 Signal Generator R&S SMT 06 832080/007 2017/11/4 Note: the calibration interval of the above test instruments is 12 months and the calibrations are traceable to international system unit (SI). Tel:(86-755)88850135 Fax: (86-755) 88850136 http://www.mtitest.com E-mail:mti@51mti.com Address:1F& 3F, East Block, Hengfang Industrial Park, Xingye Road,Xixiang, Bao'an District, Shenzhen, Guangdong,P. R. China.

- Page 8of 12- Report No.: MTi170228E061 4. Test Result 4.1Antenna requirement 4.1.1Requirement defined in FCC 15.203 An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier current devices or to devices operated under the provisions of §15.211, §15.213, §15.217, §15.219, or §15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional radiators which, in accordance with §15.31(d), must be measured at the installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed so that the limits in this part are not exceeded. 4.1.2EUT antenna description The radio antenna of EUT is an internal permanently attached antenna, the maximum gain is 0 dBi. So the antenna meets the requirement of this part. Antenna Tel:(86-755)88850135 Fax: (86-755) 88850136 http://www.mtitest.com E-mail:mti@51mti.com Address:1F& 3F, East Block, Hengfang Industrial Park, Xingye Road,Xixiang, Bao'an District, Shenzhen, Guangdong,P. R. China.

- Page 9of 12- Report No.: MTi170228E061 4.2 20dB emission bandwidth 4.2.1 Limits The bandwidth of the emissions shall be no wider than 0.25% of the center frequency for devices operating above 70MHz and below 900MHz. So the emission bandwidth limits have been calculated in below table. Fundamental Frequency 20 dB Bandwidth Limits (MHz) 433.92MHz 1.0848 4.2.2 Testmethod Set Spectrum Analyzer centre Frequency= Fundamental Frequency, RBW=10 kHz, VBW= 30 kHz, Span= 1 MHz Allow the trace to stabilize, measure the maximum width of the emission that is constrained by the frequencies associated withthe two outermost amplitude points (upper and lower frequencies) that are attenuated by 20 dBrelative to the maximum level measured in the fundamental emission. 4.2.3Test result Frequency 20dB Bandwidth (MHz) Result (MHz) 433.92 0.122 PASS * RBW 10 kHz Marker 1 [T1 ] * VBW 30 kHz 73.27 dBµV Ref 90 dBµV * Att 10 dB * SWT 300 ms 433.954000000 MHz 90 ndB [T1] 20.00 dB BW 122.000000000 kHz Temp 1 [T1 ndB] A 80 1 53.81 dBµV 1 PK 433.893000000 MHz MAXH 70 Temp 2 [T1 ndB] 53.05 dBµV 434.015000000 MHz TDF 60 T1 T2 50 40 3DB 30 20 10 0 -10 Center 433.92 MHz 100 kHz/ Span 1 MHz Date: 14.MAR.2017 02:33:05 Tel:(86-755)88850135 Fax: (86-755) 88850136 http://www.mtitest.com E-mail:mti@51mti.com Address:1F& 3F, East Block, Hengfang Industrial Park, Xingye Road,Xixiang, Bao'an District, Shenzhen, Guangdong,P. R. China.

- Page 10of 12- Report No.: MTi170228E061 4.3Radiated emission 4.3.1 Limit In addition to the provisions of Section 15.205, the field strength of emissions from intentional radiators shall not exceed the following: Field Strength of Spurious Fundamental Frequency Field Strength of Fundamental Emissions (MHz) (microvolt/meter) at 3m (microvolt/meter) at 3m 40.66~40.70 2250 225 70~130 1250 125 130~174 1250 to 3750(**) 125 to 375(**) 174~260 3750 375 260~470 3750 to 12500(**) 375 to 1250(**) Above 470 12500 1250 ** Linear interpolations, the formulas for calculating the maximum permitted fundamental field strengths are as follows: as shown in the above table, based on the average value of the measured emissions.As an alternative, compliance with the limits in the above table may be based on the use of measurement instrumentation with a CISPR quasi-peak detector. The limits on the field strength of the spurious emissions in the above table are based on the fundamental frequency of the intentional radiator. Spurious emissions shall be attenuated to the average (or, alternatively, CISPR quasi-peak) limits shown in this table or to the general limits shown in §15.209, whichever limit permits a higher field strength. Field Field Frequency strength strength Detector Measurementdistance (MHz) μV/m dBμV/m 30-88 100 40 QP 88-216 150 43.5 QP 216-960 200 46 QP 3m 960-1000 500 46 QP Above 1000 500 54 AV Above 1000 5000 74 PK 4.3.2 Test method The measuring distance of 3m shall be used for measurements at frequency up to 1GHz and above 1 GHz. The EUT was placed on a rotating 0.8m high above ground; the table was rotated 360 degrees to determine the position of the highest radiation. The Test antenna shall vary between 1m and 4m, Both Horizontal and Vertical antenna are set to make measurement. For the actual test configuration, please see the test setup photo. 4.3.3 Test Result Tel:(86-755)88850135 Fax: (86-755) 88850136 http://www.mtitest.com E-mail:mti@51mti.com Address:1F& 3F, East Block, Hengfang Industrial Park, Xingye Road,Xixiang, Bao'an District, Shenzhen, Guangdong,P. R. China.

- Page 11of 12- Report No.: MTi170228E061 PK: Result Margin Frequency AV Limit dBμV/m (dB) Remark MHz Hor. Ver. dBμV/ m Hor. Ver. 433.92 72.28 61.95 80.8 -28.52 -38.85 Fundamental 867.84 55.32 43.89 60.8 -25.48 -36.91 Harmonics 1301.76 47.98 35.47 60.8 -32.82 -45.33 Harmonics Remark: If the PK measured values lower than average mode limit, the EUT shall be deemed to meet average limits. Tel:(86-755)88850135 Fax: (86-755) 88850136 http://www.mtitest.com E-mail:mti@51mti.com Address:1F& 3F, East Block, Hengfang Industrial Park, Xingye Road,Xixiang, Bao'an District, Shenzhen, Guangdong,P. R. China.

- Page 12of 12- Report No.: MTi170228E061 4.4 Time of occupancy (dwell time) 4.4.1 Limit 15.231a（1） A manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released. 4.4.2 Test method Setup the EUT as show in the block diagram above. Set Spectrum Analyzer Centre Frequency= Fundamental Frequency, RBW=1MHz, VBW= 1MHz, Span= 0 Hz. Sweep Time= 8 Seconds. Setup the EUT as normal operation and press Transmitter button. Release the button, use Delta Mark function to test the time. 4.4.3 Test Result Release Time(s) Limit(s) Result 0.288 5 PASS RBW 1 MHz Delta 1 [T1 ] * VBW 1 MHz 0.18 dB Ref 90 dBµV * Att 10 dB SWT 8 s 288.000000 ms 90 Marker 1 [T1 ] 37.65 dBµV 1.528000 s A 80 SGL 1 PK * CLRWR 70 TDF 60 50 40 1 1 3DB 30 20 10 0 -10 Center 433.92 MHz 800 ms/ Date: 14.MAR.2017 02:41:17 ----END OF REPORT---- Tel:(86-755)88850135 Fax: (86-755) 88850136 http://www.mtitest.com E-mail:mti@51mti.com Address:1F& 3F, East Block, Hengfang Industrial Park, Xingye Road,Xixiang, Bao'an District, Shenzhen, Guangdong,P. R. China.


Document Created: 2017-03-31 20:18:28
Document Modified: 2017-03-31 20:18:28
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC