Test Report

FCC ID: 2AAZR8020A

Test Report

Download: PDF
FCCID_2384235

FCC PART 15.249 EMI MEASUREMENT AND TEST REPORT For Shenzhen Highstar Electrical Co., Ltd Building 6,Highstar Industrial zone,Gangtou,Bantian Street,Longgang District, Shenzhen,China FCC ID: 2AAZR8020A September 3, 2014 This Report Concerns: Equipment Type: Original Report 'ITWIST'Bluetooth Speaker Test Engineer: Lisa Chen Report No.: BSL14060143B Receive EUT August 26, 2014 / Date/Test Date: August 26-September 3, 2014 Reviewed By: Sky Zhang BSL Testing Co.,LTD. NO. 24, ZH Park, Nantou, Shenzhen, 518000 China Prepared By: Tel: 86- 755-26508703 Fax: 86- 755-26508703 Note: The test report is specially limited to the above company and this particular sample only. It may not be duplicated without prior written consent of BSL Testing Co.,LTD. This report must not be used by the client to claim product certification,approval,or endorsement by NVLAP, NIST or any agency of the US Government.

FCC ID: 2AAZR8020A TABLE OF CONTENTS 1. GENERAL INFORMATION ....................................................................................................3 1.1. Report information............................................................................................................3 1.2. Measurement Uncertainty.................................................................................................3 2. PRODUCT DESCRIPTION ......................................................................................................4 2.1. EUT Description ...............................................................................................................4 2.2. Block Diagram of EUT Configuration..............................................................................5 2.3. Support Equipment List ....................................................................................................5 2.4. Test Conditions .................................................................................................................5 3. TEST RESULTS SUMMARY ...................................................................................................6 Modifications ................................................................................................................................6 4. TEST EQUIPMENT USED .......................................................................................................7 5. ANTENNA REQUIREMENT ...................................................................................................8 5.1. Standard Applicable..........................................................................................................8 5.2. Antenna Connected Construction .....................................................................................8 5.3. Result ................................................................................................................................8 6. CONDUCTED POWER LINE TEST .......................................................................................9 6.1. Test Equipment .................................................................................................................9 6.2. Test Procedure ..................................................................................................................9 6.3. Test Setup..........................................................................................................................9 6.4. Conducted Power line Emission Limits............................................................................9 6.5. Conducted Power Line Test Result.................................................................................10 7. RADIATED EMISSION TEST ...............................................................................................12 7.1. Test Equipment ...............................................................................................................12 7.2. Test Procedure ................................................................................................................12 7.3. Radiated Test Setup ........................................................................................................12 7.4. Radiated Emission Limit.................................................................................................14 7.5. Radiated Emission Test Result .......................................................................................15 8. BAND EDGE .............................................................................................................................20 8.1. Test Equipment ...............................................................................................................20 8.2. Test Procedure ................................................................................................................20 8.3. Band Edge FCC 15.249(d) Limit....................................................................................20 8.4. Band Edge Test Result....................................................................................................21 9. 20-DB BANDWIDTH ...............................................................................................................22 9.1. Test Equipment ...............................................................................................................22 9.2. Test Procedure ................................................................................................................22 9.3. Limit................................................................................................................................22 9.4. Test Result /Plots ............................................................................................................22 Page 2/25

FCC ID: 2AAZR8020A 1. GENERAL INFORMATION 1.1. Report information 1.1.1.This report is not a certificate of quality; it only applies to the sample of the specific product/equipment given at the time of its testing. The results are not used to indicate or imply that they are application to the similar items. In addition, such results must not be used to indicate or imply that BSL approves recommends or endorses the manufacture, supplier or use of such product/equipment, or that BSL in any way guarantees the later performance of the product/equipment. 1.1.2.The sample/s mentioned in this report is/are supplied by Applicant, BSL therefore assumes no responsibility for the accuracy of information on the brand name, model number, origin of manufacture or any information supplied. 1.1.3.Additional copies of the report are available to the Applicant at an additional fee. No third part can obtain a copy of this report through BSL, unless the applicant has authorized BSL in writing to do so. Test Facility - The test site used to collect the radiated data is located on the address of BSL Testing Co.,LTD. (FCC Registered Test Site Number: 191509) on NO. 24, ZH Park, Nantou, Shenzhen, 518000 China The Test Site is constructed and calibrated to meet the FCC requirements. 1.2. Measurement Uncertainty The reported uncertainty of measurement y U,where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2,providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 Conducted Emission Test +/-1.25dB 2 RF Power, Conducted +/-0.20dB 3 Spurious emissions, conducted +/-0.33dB 4 All emissions, radiated (<1G) +/-3.47dB 5 All emissions, radiated (>1G) +/-3.82dB 6 Temperature +/-0.5 dB 7 Humidity +/-2% Page 3/25

FCC ID: 2AAZR8020A 2. PRODUCT DESCRIPTION 2.1. EUT Description Description : 'ITWIST'Bluetooth Speaker Applicant : Shenzhen Highstar Electrical Co., Ltd Building 6,Highstar Industrial zone,Gangtou,Bantian Street,Longgang District,Shenzhen,China Manufacturer : Shenzhen Highstar Electrical Co., Ltd Building 6,Highstar Industrial zone,Gangtou,Bantian Street,Longgang District,Shenzhen,China Model Number : HSD8020A Modulation type : GFSK Antenna gain : 0dBi Antenna type : PCB Antenna Frequency : 2402-2480MHz BT version : 2.1 Number of Channels : 79 Channels Power Supply : DC 3.7V Battery and charging DC 5V USB Channel List Frequency Frequency Frequency Channel Channel Channel (MHz) (MHz) (MHz) 00 2402 27 2429 54 2456 01 2403 28 2430 55 2457 02 2404 29 2431 56 2458 03 2405 30 2432 57 2459 04 2406 31 2433 58 2460 05 2407 32 2434 59 2461 06 2408 33 2435 60 2462 07 2409 34 2436 61 2463 08 2410 35 2437 62 2464 09 2411 36 2438 63 2465 10 2412 37 2439 64 2466 11 2413 38 2440 65 2467 12 2414 39 2441 66 2468 13 2415 40 2442 67 2469 14 2416 41 2443 68 2470 15 2417 42 2444 69 2471 16 2418 43 2445 70 2472 17 2419 44 2446 71 2473 18 2420 45 2447 72 2474 19 2421 46 2448 73 2475 20 2422 47 2449 74 2476 21 2423 48 2450 75 2477 22 2424 49 2451 76 2478 23 2425 50 2452 77 2479 24 2426 51 2453 78 2480 25 2427 52 2454 26 2428 53 2455 Page 4/25

FCC ID: 2AAZR8020A 2.2. Block Diagram of EUT Configuration Adapter EUT Figure 1 EUT Setup 2.3. Support Equipment List Used Name Model No S/N Manufacturer (Y/N) Adapter GDJ-050-200 - Highstar Y 2.4. Test Conditions Items Required (IEC 68-1) Actual Temperature ( ) 15-35 20-25 Humidity (%RH) 25-75 50-63 Barometric pressure 860-1060 950-1000 (mbar) Page 5/25

FCC ID: 2AAZR8020A 3. TEST RESULTS SUMMARY FCC 15 Subpart C, Paragraph 15.249:2013 FCC Rules Description of Test Result Section 15.207 Conducted Emission Compliant Section 15.249(a) The fundamental field strength Compliant and the harmonics Section 15.209 Radiated Emission Compliant Section 15.249(d) Section 15.249(d) Band Edge Compliant Section 15.203 Antenna Requirement Compliant Section 15.249 20dB Bandwidth Compliant Remark: “N/A” means “Not applicable”. Statement: All testing was performed using the test procedures found in ANSI C63.4-2003. Modifications No modification was made. Page 6/25

FCC ID: 2AAZR8020A 4. TEST EQUIPMENT USED CAL. EQUIPMENT/FACIL MANUFACTURE SERIAL DATE OF MODEL INTERV ITIES R NO. CAL. AL 3m Semi-Anechoic Chengyu Electron 9 (L)*6 BSL086 Aug. 23 2014 1 Year Chamber (W)* 6 (H) EMI Test Receiver Rohde & Schwarz ESCI3 BSL001 Sep. 28 2013 1 Year BiConiLog Antenna Rohde & Schwarz HL562 BSL009 Sep. 28 2013 1 Year Double -ridged Rohde & Schwarz 9120D BSL008 Aug. 27 2014 1 Year waveguide horn Horn Antenna ETS-LINDGREN 3160 BSL072 Dec. 28 2013 1 Year Cable Rohde & Schwarz BSL045 BSL045 Aug. 27 2014 1 Year Cable Rohde & Schwarz BSL046 BSL046 Aug. 27 2014 1 Year Cable Rohde & Schwarz BSL047 BSL047 Aug. 27 2014 1 Year Amplifier(100kHz-40G R&S SMR40 BSL007 Sep. 28 2013 1 Year Hz) Band filter Amindeon 82346 BSL049 Aug. 27 2014 1 Year Active Loop Antenna EMTES EM15 BSL011 Sep. 28 2013 1 Year Coaxial Switch YUANFANG TA218B BSL004 Aug. 27 2014 1 Year Spectrum analyzer Rohde & Schwarz FSP40 BSL049 Sep. 28 2013 1 Year Shielding Room zhongyu Electron 7.0(L)x3.0( BSL085 Sep. 28 2013 1 Year W)x3.0(H) EMI Test Receiver R&S ESPI BSL002 Sep. 28 2013 1 Year 10dB Pulse Limita R&S BSL003 BSL003 Sep. 28 2013 1 Year Coaxial Switch YUANFANG TA218B BSL004 Aug. 27 2014 1 Year LISN Rohde & Schwarz ESH3-Y5 BSL005 Sep. 28 2013 1 Year Coaxial Cable YUANFANG BSL048 BSL048 Aug. 27 2014 1 Year EMI TEST AUDIX E3 N/A N/A N/A SOFTWARE Page 7/25

FCC ID: 2AAZR8020A 5. ANTENNA REQUIREMENT 5.1. Standard Applicable For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 5.2. Antenna Connected Construction According to § 15.203, An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. The antenna used in this product is PCB Antenna. The antenna is permanently attached. Refer to the product photo. 5.3. Result Compliance Page 8/25

FCC ID: 2AAZR8020A 6. CONDUCTED POWER LINE TEST 6.1. Test Equipment Please refer to section 4 this report. 6.2. Test Procedure The EUT and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.).This provides a 50ohm/50uh coupling inpedance for the measuring equipment.The peripheral devices are also connected to the main power through a LISN that provides a 50ohm/50uh coupling inpedance with 50ohm termination. Both sides of A.C. Line are check for maximum conducted interference.In order to find the maximum emission,the relative positions of equipment and all of the interface cables must be changed according to ASIN C63.4:2003 on conducted measurement .Conducted emissions were invested over the frequency range from 0.15MHz to 30MHz using a receiver bandwidth of 9kHz. 6.3. Test Setup For the actual test configuration,Please refer to the related items-Photos of testing 6.4. Conducted Power line Emission Limits FCC Part 15 Paragraph 15.207 (dBuV) Frequency Range Class A Class B (MHZ) QP/AV QP/AV 0.15-0.5 79/66 65-56/56-46 0.5-5.0 73/60 56-46 5.0-3.0 73/60 60-50 Note: In the above table, the tighter limit applies at the band edges. Page 9/25

FCC ID: 2AAZR8020A 6.5. Conducted Power Line Test Result PASS Link Mode Page 10/25

FCC ID: 2AAZR8020A Page 11/25

FCC ID: 2AAZR8020A 7. RADIATED EMISSION TEST 7.1. Test Equipment Please refer to section 4 this report. 7.2. Test Procedure The EUT and its simulators are placed on a turntable, which is 0.8 meter high above ground. The turntable can rotate 360 degrees to determine the position of the maximum emission level. EUT is set 3.0 meters away from the receiving antenna, which is mounted on an antenna tower. The antenna can be moved up and down between 1.0 meter and 4 meters to find out the maximum emission level. Calibrated Loop antenna is used as receiving antenna for frequencies below 30MHz, Calibrated Bilog antenna is used as receiving antenna for frequencies between 30 MHz and 1 GHz, Calibrated Horn antenna is used as receiving antenna for frequencies above 1000MHz. Both horizontal and vertical polarizations of the antenna are set on measurement. In order to find the maximum emission levels, all of the interface cables must be manipulated according to ANSI C63.4: 2003 on radiated emission measurement. The bandwidth of test receiver is set at 9kHz in below 30MHz. and set at 120kHz in 30-1000MHz, and 1MHz in above 1000MHz. The frequency range from 9kHz to 25GHz is checked. The final measurement in band 9-90kHz, 110-490kHz and above 1000MHz is performed with Peak detector and Average detector. Except those frequency bands mention above, the final measurement for frequencies below 1000MHz is performed with Quasi Peak detector. Through three orthogonal axes to determine which attitude and equipment arrangement produces the highest emission relative to the limit. And Y direction is worst mode. 7.3. Radiated Test Setup (A) Radiated Emission Test Set-Up, Frequency Below 30MHz Page 12/25

FCC ID: 2AAZR8020A (B) Radiated Emission Test Set-Up, Frequency Below 1000MHz (C) Radiated Emission Test Set-Up, Frequency above 1000MHz Page 13/25

FCC ID: 2AAZR8020A 7.4. Radiated Emission Limit All emission from a digital device,including any network of conductors and apparatus connected thereto,shall not exceed the level of field strength specified below : A. Fundamental and Harmonics Radiated Emissions 15.249(a) Limit Fundamental Field as trength of Fundamental(3m) Field as trength of Harmonics(3m) Frequency (MHZ) mV/m dBuV/m uV/m dBuV/m 902-928 50 94(AV) 114(Peak) 500 54(AV) 74(Peak) 2400-2483.5 50 94(AV) 114(Peak) 500 54(AV) 74(Peak) Note: (1) RF Voltage (dBuV)=20 log Voltage(uV) (2) Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. (3) The emission limit in this paragraph os based on measurement instrumentation employing an average detector.Measurement using instrumentation with a peak detector function,corresponding to 20dB above the maximum permitted average limit. B. Spurious Radiated Emissions. Limit Frequency Field Strength of Field Strength of The final Measurement (MHz) Quasi-peak Value Quasi-peak Value measurement in band distance (m) (microvolts/m) (dBµV/m) 9-90kHz, 110-490kHz and 0.009 - 0.490 2400/F(kHz) / 300 above 1000MHz is 0.490 - 1.705 24000/F(kHz) / 30 performed with Average detector. 1.705-30 30 29.5 30 Except those frequency bands 30 - 88 100 40 3 mention above, the 88 - 216 150 43.5 3 final measurement for frequencies 216 - 960 200 46 3 below 1000MHz is performed with Above 960 500 54 3 Quasi Peak detector. Note: (1) RF Voltage (dBuV)=20 log Voltage(uV) (2) In the Above Table,the tighter limit applies at the band edges. (3) Distaqnce refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. Page 14/25

FCC ID: 2AAZR8020A 7.5. Radiated Emission Test Result Pass A. Fundamental Radiated Emissions Data CH Low Freq. Read Antenna Cable Preamp Emission HORIZ/ Limits Margin (MHz) Level Factor Factor (dBuV/m) VERT (dBuV/m) (dB) Loss (dBuV) (dB/m) (dB) AV/PK AV/PK AV/PK (dB) 2402 78.59/88.32 27.47 5.42 30.17 81.31/91.04 VERT 94/114 -12.69/-22.96 2402 80.7/90.21 27.47 5.42 30.17 83.42/92.93 HORIZ 94/114 -10.58/-21.07 CH Middle Freq. Read Antenna Cable Preamp Emission HORIZ/ Limits Margin (MHz) Level Factor Factor (dBuV/m) VERT (dBuV/m) (dB) Loss (dBuV) (dB/m) (dB) AV/PK AV/PK AV/PK (dB) 2441 79.75/88.82 27.40 5.40 30.15 82.4/91.47 VERT 94/114 -11.6/-22.53 2441 80.7/90.43 27.40 5.40 30.15 83.35/93.08 HORIZ 94/114 -10.65/-20.92 CH High Freq. Read Antenna Cable Preamp Emission HORIZ/ Limits Margin (MHz) Level Factor Factor (dBuV/m) VERT (dBuV/m) (dB) Loss (dBuV) (dB/m) (dB) AV/PK AV/PK AV/PK (dB) 2480 78.45/87.55 27.50 5.46 29.98 81.43/90.53 VERT 94/114 -12.57/-23.47 2480 80.39/89.5 27.50 5.46 29.98 83.37/92.48 HORIZ 94/114 -10.63/-21.52 Remark: Final Emission =Receiver Read level + Antenna Factor + Cable Loss – Preamplifier Factor Page 15/25

FCC ID: 2AAZR8020A B. General Radiated Emissions Data For below 9kHz-30MHz Spurious Freq. Emission(dBuV/m) Limits(dBuV/m) Margin (MHz) PK / AV PK / AV (dB) - - - - - - - - Note: 1. Emissions attenuated more than 20 dB below the permissible value are not reported. Page 16/25

FCC ID: 2AAZR8020A For 30M-1000MHz Spurious Corrected Factor = Antenna Factor + Cable Loss – Amplifier Gain 2441MHz Transmitting(Worst case mode) Page 17/25

FCC ID: 2AAZR8020A Page 18/25

FCC ID: 2AAZR8020A For 1000MHz-25000MHz Spurious CH Low Freq. Emission(dBuV/m) HORIZ/ Limits(dBuV/m) Margin (MHz) AV/PK VERT AV/PK (dB) 4804 38.58/48.51 54.0/74.0 -15.42/-25.49 7206 42.54/52.51 VERT 54.0/74.0 -11.46/-21.49 9608 40.53/50.53 54.0/74.0 -13.47/-23.47 4804 37.45/49.12 54.0/74.0 -16.55/-24.88 7206 44.99/54.99 HORIZ 54.0/74.0 -9.01/-19.01 9608 46.48/56.48 54.0/74.0 -7.52/-17.52 CH Middle Freq. Emission(dBuV/m) HORIZ/ Limits(dBuV/m) Margin (MHz) AV/PK VERT AV/PK (dB) 4882 33.48/43.56 54.0/74.0 -20.52/-30.44 7323 39.37/49.32 VERT 54.0/74.0 -14.63/-24.68 9764 38.3/48.33 54.0/74.0 -15.7/-25.67 4882 33.56/43.59 54.0/74.0 -20.44/-30.41 7323 41.63/51.63 HORIZ 54.0/74.0 -12.37/-22.37 9764 46.37/56.36 54.0/74.0 -7.63/-17.64 CH High Freq. Emission(dBuV/m) HORIZ/ Limits(dBuV/m) Margin (MHz) AV/PK VERT AV/PK (dB) 4960 36.58/46.62 54.0/74.0 -17.42/-27.38 7440 40.45/50.45 VERT 54.0/74.0 -13.55/-23.55 9920 41.49/51.58 54.0/74.0 -12.51/-22.42 4960 35.85/45.85 54.0/74.0 -18.15/-28.15 7440 40.54/50.55 HORIZ 54.0/74.0 -13.46/-23.45 9920 42.54/52.63 54.0/74.0 -11.46/-21.37 Note: 1. The average measurement was not performed when the peak measured data under the limit of average detection. 2. Emissions attenuated more than 20 dB below the permissible value are not reported. Page 19/25

FCC ID: 2AAZR8020A 8. BAND EDGE 8.1. Test Equipment Please refer to Section 4 this report. 8.2. Test Procedure The EUT and its simulators are placed on a turn table which is 0.8 meter above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 3 meters. The antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Both horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission, all of the interface cables must be manipulated according to ANSI C63.4: 2003 on radiated measurement. The bandwidth setting below 1GHz and above 1GHz on the field strength meter is 120 kHz and 1MHz respectively. 8.3. Band Edge FCC 15.249(d) Limit Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in Section 15.209, whichever is the lesser attenuation. Page 20/25

FCC ID: 2AAZR8020A 8.4. Band Edge Test Result Pass ALL of the restriction bands were tested,and only the data of worst case was exhibited. CH Low Freq. Emission(dBuV/m) HORIZ/ Limits(dBuV/m) Margin (MHz) AV/PK VERT AV/PK (dB) 2390 39.4/47.19 54.0/74.0 -14.6/-26.81 2400 44.67/54.09 VERT 54.0/74.0 -9.33/-19.91 2390 40.13/49.2 54.0/74.0 -13.87/-24.8 2400 42.36/55.31 HORIZ 54.0/74.0 -11.64/-18.69 CH High Freq. Emission(dBuV/m) HORIZ/ Limits(dBuV/m) Margin (MHz) AV/PK VERT AV/PK (dB) 2483.5 38.13/49.46 54.0/74.0 -15.87/-24.54 2500.00 35.16/45.05 VERT 54.0/74.0 -18.84/-28.95 2483.5 39.49/50.05 54.0/74.0 -14.51/-23.95 2500.00 36.05/44.2 HORIZ 54.0/74.0 -17.95/-29.8 Remark: 1. Factor = Antenna Factor + Cable Loss – Pre-amplifier. Page 21/25

FCC ID: 2AAZR8020A 9. 20-DB BANDWIDTH 9.1. Test Equipment Please refer to Section 4 this report. 9.2. Test Procedure 1. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 2. Set center frequency of spectrum analyzer = operating frequency. 3. The spectrum analyzer as RBW=30 KHz, VBW=100 KHz, Sweep=auto 4. Mark the peak frequency and –20dB (upper and lower) frequency. 9.3. Limit Please refer section15.249 9.4. Test Result /Plots Channel 20dB Limit Frequency Bandwidth (MHz) (MHz) / 2402 0.792 / 2441 0.792 / 2480 0.796 Page 22/25

FCC ID: 2AAZR8020A * RBW 30 kHz Marker 1 [T1 ] * VBW 100 kHz -15.82 dBm Ref 10 dBm Att 40 dB SWT 2.5 ms 2.402016000 GHz 10 ndB [T1] 20.00 dB BW 792.000000000 kHz Temp 1 [T1 ndB] A 0 -35.85 dBm 1 PK 2.401620000 GHz MAXH -10 Temp 2 [T1 ndB] 1 -35.69 dBm 2.402412000 GHz -20 -30 PS T1 T2 -40 -50 -60 -70 -80 -90 Center 2.402 GHz 200 kHz/ Span 2 MHz Page 23/25

FCC ID: 2AAZR8020A * RBW 30 kHz Marker 1 [T1 ] * VBW 100 kHz -15.38 dBm Ref 10 dBm Att 40 dB SWT 2.5 ms 2.441020000 GHz 10 ndB [T1] 20.00 dB BW 792.000000000 kHz Temp 1 [T1 ndB] A 0 -35.20 dBm 1 PK 2.440620000 GHz MAXH -10 Temp 2 [T1 ndB] 1 -35.40 dBm 2.441412000 GHz -20 -30 PS T1 T2 -40 -50 -60 -70 -80 -90 Center 2.441 GHz 200 kHz/ Span 2 MHz Page 24/25

FCC ID: 2AAZR8020A * RBW 30 kHz Marker 1 [T1 ] * VBW 100 kHz -16.44 dBm Ref 10 dBm Att 40 dB SWT 2.5 ms 2.480024000 GHz 10 ndB [T1] 20.00 dB BW 796.000000000 kHz Temp 1 [T1 ndB] A 0 -36.57 dBm 1 PK 2.479616000 GHz MAXH -10 Temp 2 [T1 ndB] 1 -36.61 dBm 2.480412000 GHz -20 -30 PS T1 T2 -40 -50 -60 -70 -80 -90 Center 2.48 GHz 200 kHz/ Span 2 MHz End Of The Report Page 25/25


Document Created: 2014-09-10 15:25:55
Document Modified: 2014-09-10 15:25:55
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC